Your Tower speaker should be treated with care. The information below has been
provided in the interest of safety and will help you to enjoy this product and the
benefits it brings for many years.
• Keep the product and all its parts out of reach of small children.
• This product is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
• Keep it dry. Avoid exposure to precipitation, humidity and liquids which could all
aect the product circuitry.
• Do NOT leave it in high temperatures as electronic devices and plastic parts may
warp in heat.
• Do NOT leave it in low temperatures as moisture can form inside the product,
which may damage the circuit board.
• Do NOT block or cover slots, holes or openings on the product by placing on soft
furnishings such as carpets, rugs or beds as these are provided for functionality
and/or ventilation to ensure safe operation of the product
• Do NOT store in dusty or dirty areas.
• Disconnect your Tower speaker from the mains power supply during
thunderstorms.
• Always check that you have completely switched o your Tower speaker, before
you change or disconnect the power supply.
• Only use the power supply that came with the product. Using an unauthorised
power supply will invalidate your guarantee and may irrecoverably damage the
product.
• Where the mains power plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
• Do NOT attempt to open the product. This product does not contain any user
serviceable parts. Unauthorised handling of the device may damage it and will void
your warranty.
• Do NOT use your Tower speaker near emergency/intensive care medical
equipment; if you have a pacemaker fitted or during an electrical storm.
• Do NOT use harsh chemicals, cleaning solvents or detergents to clean the
product. Wipe with a damp (not wet) soft cloth to clean.
• If the Tower speaker remote control will not be used for a long period of time,
make sure that all of the batteries are removed from the battery compartment.
3
• Only use recommended batteries or those of the same equivalent type.
• Do not mix old and new batteries or batteries of dierent types.
• Batteries are to be inserted with the correct polarity.
• The supply terminals are not to be short-circuited.
• Do not attempt to recharge non-rechargeable batteries
• Dispose of old batteries carefully.
• Never throw batteries in a fire or attempt to open the outer casing.
Batteries are harmful if swallowed, so keep away from young children.
4
Instructions for use
Check the package contents
The package contains:
• 1 x Tower speaker
• 1 x Base
• 2 x Assembly screws
• 1 x Dock support stand
• 1 x Stereo audio connection cable with 3.5mm plug
• 1 x Mains adaptor
• 1 x Remote control
• 1 x Instruction manual
Where to put your Tower speaker
It is important that you consider carefully in advance where your Tower speaker will be
situated and make sure that it is:
• on a flat and stable surface
Note: Never place your Tower speaker on antique or polished surfaces.
• within 1.4 metres of a power socket. Please ensure that the mains power lead is
not a trip hazard.
• at least 1 metre away from other electrical appliances to avoid interference
• where it will be in range of the connected or ‘paired’ blutooth device (eg. iPod/
iPhone/iPad/Android/other phone/computer), which is about 10 metres or less
(33 feet or less) in line of sight.
• where you can easily access the controls on the top of the product, if you choose
not to use the remote control.
• where you can fully extend the wire radio aerial
• away from bright sunlight or heat sources, such as a radiator
• not in a humid or very damp place such as a bathroom
5
Setting up
1. Attach the Tower speaker to the separate base using the screws supplied.
2. Insert the dock support stand supplied into the slot on the top of the Tower
speaker, just behind the dock connector.
3. Insert 2 x AAA batteries into the remote control, noting the ‘+’ and ‘-’ markings and
position the batteries the correct way around.
4. Replace the battery cover, making sure it ‘clicks’ shut.
5. Connect the mains power lead into the socket on the back of the Tower speaker at
the top.
6. Plug the power adaptor into the mains power wall socket and switch on. The red
Standby led will light up.
7. Press and release the ‘ ’ button on the top of the Tower speaker or on the remote
control. The display will fully switch on and the current mode (iPod/BT/LINE/AUX/
Radio frequency) will be displayed.
6
Using your Tower Speaker with Dock
Switch on
Press and release the ‘ ’ button on the top of the Tower speaker or on the remote
control. The display will fully switch on and the current mode (iPod/BT/LINE/AUX/
Radio frequency) will be displayed.
Switch o
Press and release the ‘ ’ button on the top of the Tower speaker or on the remote
control. The Tower speaker will go into Standby mode and the red Standby led will
light up.
To completely switch o the Tower speaker, switch o the mains power at the wall
socket.
Note: If you do not use your Tower speaker for 15 minutes and no audio signal is
received, the speaker will automatically go into standby mode. Press the ‘ ’ button on
the top of the speaker or on the remote control to switch the product back on.
Change the mode
Briefly press the ‘Source’ button on the top of the Tower speaker or on the remote
control to change modes. iPod/BT/LINE/AUX/Radio modes are available. Please
check the display, which will confirm the mode.
Adjusting the volume
Use the ‘Volume +’ or ‘Volume -’ buttons on the Tower speaker or on the remote
control to adjust the volume. When you adjust the volume, please check the display
which will confirm the volume setting.
Mute
Press and release the ‘Mute’ button on the remote control to turn the sound o. ‘Mute’
will be displayed
Press and release the ‘Mute’ button to turn the sound on again.
Adjusting the bass setting
Use the ‘Bass +’ or ‘Bass -’ buttons on the remote control to adjust the bass setting.
When you adjust the bass, please check the display, which will confirm the setting.