Burley 09 dlite, 09 Solo, 09 Encore User Manual

Installation Instructions for ‘09 d’lite™, Encore® and Solo™ (Euro) Child Trailers
Installation Instructions for ‘09 d’lite™, Encore® and Solo™ (Euro) Child Trailers
Contents:
(1) Burley Owner’s Instruction and Safety Manual (1) Hitch (1) Clear light with batteries included (1) Red light with batteries included (2) Phillip Pan screws (2) Brackets for lights (1) Wheel guard assembly:
Tools Required: Phillips screwdriver 4mm hex wrench 10mm or open end wrench
Note : Consult your Burley Owner’s
Instruction and Safety Manual for wheel guard and hitch installation
instructions.
Roll Bar Installation
1. If handle bar receivers are already installed, loosen and remove handle bar knobs and outer handle bar receivers.
FIGUR E 1
2. Using wrench, loosen and remove lock nuts and screws from handle bar receivers.
3. From trailer front, slide roll bar into upper handle bar receivers, with curved front extending above trailer body.
4. Match holes in roll bar and inner handle bar receivers, re-install screws and tighten lock nuts.
5. Replace outer handle bar receivers and tighten knobs.
Front of Trailer
Screws
Roll Bar
FIGURE 1: Roll Bar Installa tion
Lock Nut s
Inner Handle bar
Receiver
Outer Handle bar
Rear Assembly
Receiver
Frame
Handle bar
Knob
Contents:
(1) Burley Owner’s Instruction and Safety Manual (1) Hitch (1) Clear light with batteries included (1) Red light with batteries included (2) Phillip Pan screws (2) Brackets for lights (1) Wheel guard assembly:
Tools Required: Phillips screwdriver 4mm hex wrench 10mm or open end wrench
Note : Consult your Burley Owner’s
Instruction and Safety Manual for wheel guard and hitch installation
instructions.
Roll Bar Installation
1. If handle bar receivers are already installed, loosen and remove handle bar knobs and outer handle bar receivers.
FIGUR E 1
2. Using wrench, loosen and remove lock nuts and screws from handle bar receivers.
3. From trailer front, slide roll bar into upper handle bar receivers, with curved front extending above trailer body.
4. Match holes in roll bar and inner handle bar receivers, re-install screws and tighten lock nuts.
5. Replace outer handle bar receivers and tighten knobs.
Front of Trailer
Screws
Roll Bar
FIGURE 1: Roll Bar Installa tion
Lock Nut s
Inner Handle bar
Receiver
Outer Handle bar
Rear Assembly
Receiver
Frame
Handle bar
Knob
Light Installation
Note : Clear light is mounted facing
forward, on side closest to traffic. Red light is mounted facing rear, on the side closest to traffic.
Note : Make sure on/off light switches
are accessible.
1. Remove clips and screws from back of lights.
2. Using screws, fasten brackets and lights together.
3. Mount clear light/bracket diagonally on front of roll bar and red light/bracket on rear of roll bar, both on side closest to traffic. PHOTO 1
Front of Trailer
Clear Light
PHOTO 1: Light Installat ion
Roll Bar
Red L ight
Light Installation
Note : Clear light is mounted facing
forward, on side closest to traffic. Red light is mounted facing rear, on the side closest to traffic.
Note : Make sure on/off light switches
are accessible.
1. Remove clips and screws from back of lights.
2. Using screws, fasten brackets and lights together.
3. Mount clear light/bracket diagonally on front of roll bar and red light/bracket on rear of roll bar, both on side closest to traffic. PHOTO 1
Front of Trailer
Red L ight
Roll Bar
Clear Light
PHOTO 1: Light Installat ion
Locking Quick Release/ Wheel Installation and Operation
1. With quick release lever in “open” position, insert wheel axle completely into trailer axle receiver.
2. Close quick release lever, with lever aimed towards rear of trailer. PHOTO 2
3. Verify that tires are inflated to pressure marked on the tire side wall.
4. To remove wheel from trailer axle, push locking button on side of quick release lever and open lever.
Note : The locking quick release lever
securely attaches the wheel to the trailer. If you have difficulty removing the wheel, release pressure on the quick release by pushing the end of lever in toward the trailer before pushing the locking button.
WARNING
MAKE SURE WHEELS ARE HELD SECURELY, WITH WHEEL SHAFT FULLY INSERTED INTO AXLE RECEIVER. YOU SHOULD NOT BE ABLE TO ROCK OR SHIFT WHEELS. IMPROPERLY INSTALLED WHEELS CAN FALL OFF, CAUSING AN ACCIDENT OR SERIOUS INJURY.
Quick
Rele ase
Lev er
Rear of Tra iler
PHOTO 2: Wheel Inst alla tion
Locking
But ton
Locking Quick Release/ Wheel Installation and Operation
1. With quick release lever in “open” position, insert wheel axle completely into trailer axle receiver.
2. Close quick release lever, with lever aimed towards rear of trailer. PHOTO 2
3. Verify that tires are inflated to pressure marked on the tire side wall.
4. To remove wheel from trailer axle, push locking button on side of quick release lever and open lever.
Note : The locking quick release lever
securely attaches the wheel to the trailer. If you have difficulty removing the wheel, release pressure on the quick release by pushing the end of lever in toward the trailer before pushing the locking button.
WARNING
MAKE SURE WHEELS ARE HELD SECURELY, WITH WHEEL SHAFT FULLY INSERTED INTO AXLE RECEIVER. YOU SHOULD NOT BE ABLE TO ROCK OR SHIFT WHEELS. IMPROPERLY INSTALLED WHEELS CAN FALL OFF, CAUSING AN ACCIDENT OR SERIOUS INJURY.
Quick
Rele ase
Lev er
Rear of Tra iler
PHOTO 2: Wheel Inst alla tion
Locking
But ton
B U R L E Y D E S I G N
Copyright © 2008 by Burley Design LLC. “Burley” is a registered trademark of Burley Design LLC 4020 Stewa rt Rd. Eug ene, OR 97402
:
PH 541. 687.1644
800.423. 844 5 FAX 541. 687.04 36
:
Rev 06/08
:
burley@burley. com
:
170056 Euro d’lite, Encore and Solo Installation Instructions r1
:
www.burley .com
B U R L E Y D E S I G N
Copyright © 2008 by Burley Design LLC. “Burley” is a registered trademark of Burley Design LLC 4020 Stewa rt Rd. Eug ene, OR 97402
:
PH 541. 687.1644
800.423. 844 5 FAX 541. 687.04 36
:
Rev 06/08
:
burley@burley. com
:
170056 Euro d’lite, Encore and Solo Installation Instructions r1
:
www.burley .com
Loading...