Page 1
www.burg-waechter.de
BURG-WÄCHTER KG
Altenhofer Weg 15
58300 Wetter
Germany
Elektronisches Türschloss
BA/MA TSE Set 4001 dp/mri/dn 11/2011
Montage- und Bedienungsanleitung
Installation and User Manual
Instruction de montage et mode d’emploi
Montage- en gebruiksaanwijzing
HOME
Genial sicher.
Genial einfach.
Page 2
TSE HOME 4001
English | 7
Illustrations
On key
Enter key
Ready for opening
When a valid opening code is entered, the opening readiness
icon turns on.
Blocking time
When a wrong opening code is entered three times in succession, the
lock blocks the operation for one minute. After every further wrong code
entry, the lock will be blocked for 3 minutes. During this time, the red
blocking time icon flashes and the lock cannot be opened even with the
valid opening code.
Programming status
When the programming mode is entered, the programming mode icon
turns on. It turns off, when the programming mode is terminated.
F
Entry denied
When an invalid opening code is entered, the red entry denied
icon turns on.
G
Battery replacement symbol
When the battery replacement symbol icon turns on, the batteries in
the keypad and in the cylinder has to be replaced.
H
Service call
When the service call icon turns on, a communication error between
the keypad and cylinder is indicated. In most cases, this is a sign of low
batteries in the keypad or in the cylinder. Please replace the batteries
immediately.
I
Key confirmation
Any successful key operation is confirmed with a brief flashing of
the green central confirmation LED.
Structure Dear customer,
thank you very much for choosing the BURG-WÄCHTER TSE 4001 electronic
locking system. This system has been developed and manufactured using
the latest technical potential in order to satisfy high security requirements.
The electronic cylinder can be easily used in any door, prepared for profile
cylinder up to 120 mm (60/60 mm, measured at the central fixing screw),
without the need of drilling and installing. It is perfectly appropriate for both,
new installation and retrofitting. Data transmission from the keypad unit to
the cylinder is wireless. The keypad can be located within a radius of about
10 m from the cylinder.
The BURG-WÄCHTER TSE 4001 can be controlled by using a pin-code or a
BURG-WÄCHTER TSE E-KEY – please find additional information in the User
Manual.
Important: Please read the entire User Manual before you start
programming the system.
Enjoy your new locking system.
Icons
F
G
H
I
Page 3
TSE HOME 4001
English | 8
Technical data
Blocking times
After 3 x wrong pincode entry
1 minute, then 3 minutes each time
Power supply for
keypad
2 x MIGNON LR6 AA ALKALINE
Power supply for
cylinder
2 x MICRO LR03 AAA ALKALINE
Permissible
ambient
conditions*
-15 °C / +50 °C / u
p to 95 % relative air humidity
(noncondensing)
TSE 4001 PINCODE
The electronic cylinder operates using a 6-digit pincode. In option to that,
you can also use the TSE 5103 E-KEY.
Electronic cylinder TSE 4001
The TSE 4001 electronic cylinder includes
the following standard functions:
– Number of pincodes: 1
– Number of E-KEYs: 5
Optional locking media
– TSE 5103 E-KEY remote key
Administrator code
– Factory setting: 123456 (you absolutely need to change this)
In the following description, the administrator code is referred to as
“pincode”.
1. Commissioning
When the TSE 4001 pincode is first put into operation, it is necessary to
perform a certain procedure, as the system is delivered from the factory in
a special power saving mode.
– Press “On”, the green “ready for opening”-icon flashes briefly
– Press “Enter” for approx. 5 seconds until the blocking time icon starts
flashing, while the green “ready for opening”-icon is on permanently
– The blocking time icon turns off after approx. 20 seconds. Now enter
the factory-set pincode (1-2-3-4-5-6).
When the procedure has been successfully finished, the “ready for
opening”-icon turns on, while in case of an incorrect procedure,
the “entry denied” icon flashes. In case, please repeat the procedure.
Page 4
TSE HOME 4001
English | 9
Menu functions
Besides numbers, the keypad also includes letters. In order to program
individual functions, number or letter combinations must be typed.
The initial letters of a program function create a code combination,
intended for easy memorizing. Each submenu explicitly includes this.
1 Starting the programming mode to change the lock settings
– Press “On”, then type in 76, press “Enter”
– Enter the 6-digit pincode
– The green key confirmation LED flashes briefly and the program
mode icon turns on.
The code combination “76” stands for “PM” – Programming Mode.
2 Changing the opening code (factory setting 1 2 3 4 5 6)
– Enter the programming mode, using the current pincode
– Type in your new 6-digit pincode and press “Enter”
– Repeat your new 6-digit pincode and press “Enter” briefly. If the green
“ready for opening”-icon turns on, the code change was successful.
In case the red “entry denied”-icon turns on, the code entry was wrong
and the former settings persist.
3 Unblocking the lock
– Press the “On” key
– Type the 6-digit user code, then press the “Enter” key
– The green „ready for opening“ icon goes on
– The lock can be opened by turning the door knob
4 Recording or overwriting an E-KEY in one
of the memory positions 1 to 5
– Start the programming mode using the current pincode
– Set the E-KEY into the programming mode (hold the button on the E-KEY
until the green LED on the E-KEY flashes three times in succession)
– Type in 32X (X indicates the E-KEY position on the memory cell,
numbers 1 to 5 are allowed), then press “Enter”.
– You need to leave the programming code to activate the permission to
access. Therefore press the button „On“ twice and enter the opening
code via the keypad once, then press „Enter“.
7 Resetting the radio channel
– The radio channel can be reset here (12 channels to select from; factory
setting: channel 1)). This may be required when the radio channel is
already used by another application, e.g. WLAN, which can possibly
lead to interference. In such case, please select another channel with
a spacing of at least 3 radio channels.
– Enter the programming mode using the current opening code
– Type 72X (X indicates the radio channel, numbers 1 to 12, also 01 etc.,
are allowed), then press the “Enter” key.
The combination “72” stands for “RC” – RF channel). When the action has
been performed successfully, the green „ready for opening“ LED goes on,
while the red „entry denied“ one goes on in case of error.
8 Registering the keypad
– Press “On”, type in “82”, then press “Enter”.
– Type in the valid pincode
Attention: When registering a new cylinder,
the factory code (123456) has to be entered.
When the action has been executed successfully, the green
„ready for opening“ LED turns on, while in case of rejection,
the red „entry denied“ one turns on.
In case a wrong key has been entered by mistake, the “On” key
can generally be used to return to the initial lock setting. You can
then restart the locking operation from the beginning.
As long as the programming mode is active, the icon „Prog“ is lit,
other E-KEYS can be programmed without re-entering the code.
The combination “32” stands for “AE” - add E-KEY. When the action has been
performed successfully, the green “ready for opening” LED turns on, while in
case of rejectiion, the red “entry denied” one turns on.
You can note the names of the E-KEY users and the corresponding position
numbers on page 16 of this User and Assembly Manual.
5 Deleting an E-KEY in one of the user positions 1 to 5
– Start the programming mode using the current pincode
The code combination “35” stands for “RE” - remove E-KEY. When the action
has been carried out successfully, the green „ready for opening“ LED turns on,
while in case of rejection the red „entry denied“ one turns on.
6 Synchronising the E-KEY
– In this menu, the radio channel of the E-KEY can be synchronised to
the channel of the keypad. This is necessary when the radio channel
of the cylinder is modified, although E-KEYs with the old channel
setup are still in use.
– Set the E-KEY into the programming mode (hold the button on the E-KEY
until the green LED on the E-KEY flashes three times in succession)
– Type in “37”, then press “Enter”
The combination “37” stands for “ES” – E-KEY sync. When the action has
been carried out successfully, the green „ready for opening“ LED turns on,
while in case of rejection, the red „entry denied“ one turns on.
Page 5
TSE HOME 4001
English | 10
Keypad battery replacement
1 Remove the cover by pressing its detent notches on both sides with
a pointed tool towards inside and pulling it up.
2 Insert the batteries into the keypad.
Please check the correct polarity of the cells.
3 Place the cover on the keypad.
When inserting the new batteries, please check the correct polarity,
which is indicated in the battery compartment of the keypad.
Keypad installation
1 Choose a place for fixing the keypad. Place the keypad within a maximum
distance of approx. 10 m from the lock and carry out an opening test by
entering the pincode. After a successful test, the keypad can be fixed using
either the screws (3.9 x 22 and/or 3.9 x 12) or the attached adhesive pad.
When using the screws, please remove the batteries before installation.
Please install the keypad at a place, where it is protected against
weather influences!
2 If required, replace the batteries and engage the housing cover
onto the device box.
3 Carry out a function test of the unit while the door is open.
In order to do so, enter the valid pincode several times.
Installation instructions for TSE cylinder
The installation of the TSE cylinder is described below.
Please read this Manual carefully before the assembly and then store it at
a safe place.
The cylinder is provided with a special detent system, offering you a
possibility of using the cylinder for doors up to a thickness of 120 mm
(60/60 mm, measured at the central fixing screws). No prior adjustment
is necessary.
Attention:
Attention should be paid to prevent the door knob from being
bumped, as the knob might be damaged.
The lock should not be greased or oiled.
The fixing of the knobs is provided with one incorporated hex screw
in each knob.
Attention:
Never pull the outer knob completely from the shaft, as this will
damage the electronics! The hex screw that fixes the knob onto the
shaft must be loosened only slightly and it must always remain in the
plastic knob, providing protection against pulling out the knob!
Outer side Inner side
Outer knob Inner knob
Schematic
representation
of an assembled
cylinder.
Cover Fixing screw Hex screw for fixing the
knob onto the shaft
Page 6
TSE HOME 4001
English | 11
Remark
The basic size of the cylinder is 30 mm for each side. When delivered,
the cylinder is completely pushed together (smallest possible cylinder length).
Before you embed the cylinder into the door, you need to adjust the exterior
knob to door thickness.
To install the cylinder, proceed as follows:
1 Take a rough measurement of the door thickness (incl. fittings)
2 Pull the inner knob away from the shaft, move the outer knob over the
detent system (spacing 2.85 mm) to the required dimension.
Schematic representation of
adjustment of the outer knob
3 the TSE cylinder outside in through the mortise lock into
the door and then tighten the fixing screw.
4 Shift the outer knob along the shaft until the required dimension is
attained. Please make sure that the distance between the rotary knob
and the door mounting is at least 1 mm. Then fix the knob using the
hex key.
5 Shift the interior knob into the required position on the shaft and fix
it with a distance of at least 1 mm from the strike plate by using the
hex bolt.
Make sure that the interior knob is shifted on the shaft in a way that
the fixing screw (inside the knob) faces the shaft with the little holes
at the side.
6 The function test must be made while the door is open.
Replacing the knob batteries (exterior)
Attention: When replacing the batteries, make sure that no
precipitations or humidity penetrate the batteries, as no water can
escape when the compartment has been closed.
1 Loosen the hex screw on the cover and remove it. The fixing
screw may be loosened only so far that the cover can be
opened. It must never be unscrewed from the cover.
2 Pull the silicone cover out and replace the batteries.
Check the correct polarity of the cells.
3 Place the silicone cover on the batteries, close the cover
and tighten the fixing screw.
Loading...