Page 1
CROSS PS 7500
BURG-WÄCHTER KG
Altenhofer Weg 15
58300 Wetter
Germany
ProfiScale CROSS
Cross line laser level with tripod
en
Operating instructions
CROSS
<
20 m
precision
+
1,25 %
www.burg-waechter.de
Page 2
ProfiScale CROSS PS 7500 2
Introduction
Align your tiles, furniture, pictures or borders the easy way. The lasers in the
ProfiScale CROSS cross line laser level are self-adjusting and show horizontal
and vertical lines up to 20 metres long. You’ll have both hands free at all
times – whether the device is suspended, standing upright or placed on the
tripod.
The cross laser ProfiScale CROSS uses laser beams to project horizontal and
vertical lines onto a wall. It’s the perfect aid to professionally installing wall
units, pictures, shelves etc. The cross laser ProfiScale CROSS automatically
adjusts within a range of ± 8 °.
Illustration
Laser 1
Laser 2
Laser 3
Locking switch
On/off switch
Mounting device
Battery compartment
Angle adapter for use with tripod
Tripod
Safety instructions
Failure to observe the following instructions may result
in personal injury:
1. Before using the device, you must read these instructions carefully to
ensure that you operate the device safely. Keep these instructions in a
safe place.
2. The warning label(s) on the device must never be obscured or removed
from the device.
Caution – Laser radiation
Do not stare into beam
EN 60825-1:1994 + A1:2002 + A2:2001
P
max
< 2 mW; λ = 630 – 660 nm
3. Before using the device for the first time, apply the warning labels
provided in your national language.
4. Never point the laser beam at the eyes of other persons or animals.
Never look into the light beam yourself and do not use optical devices to
focus the laser light. To do so may damage your eyes.
5. Do not allow children to operate the laser measuring tool. They may
inadvertently injure themselves or others.
6. Do not operate the device at eye level or close to reflective surfaces, as
these may reflect laser beams into your eyes.
7. Always switch the laser off when you have finished working or if you are
not using it for some time.
8. When using the pin, note that it is extremely sharp and could cause
injury if improperly used.
9. When working with the device (using the pin), make sure there are no
cables or wires close by that could be damaged by the pin.
10. Keep the device away from children and unauthorized persons.
11. For safety reasons and to maintain the warranty on the device, repairs
must only be carried out by qualified personnel using genuine parts.
12. Never expose the device to an electric voltage, as this could damage the
electronics.
13. Do not use the device in the vicinity of inflammable or explosive gases.
14. Do not use the device if it is defective.
15. Handle the device with care and do not drop it.
16. To avoid functional errors, do not dismantle the device.
17. Keep the device clean and dry.
18. When not in use, the device should be stored in the bag supplied.
19. Avoid contact with water and dust.
20. Do not use abrasive cleaners or solvents to clean the device. Use a damp
cloth and mild detergent.
21. Check the battery/batteries regularly to avoid damage.
22. Remove the battery if you are not going to use the device for a long
period.
Warranty
Congratulations!
Thank you for choosing ProfiScale quality measuring technology by BURGWÄCHTER. BURG-WÄCHTER offers a warranty of 2 years’ duration from the
date of purchase. The warranty does not cover damage caused by improper
use, overloading the device or incorrect storage as well as normal wear and
defects that only have an insignificant effect on the value or usability of
the device. The warranty shall be immediately invalidated if unauthorized
persons work on the device. In the event that a warranty claim arises, please
hand over the entire device incl. packaging, description and batteries along
with the sales receipt to your dealer.
Technical data
Length of laser line
approx. 8 m
Width of laser line
< 5 mm
Resolution
±10 mm (in 8 m)
Laser output
< 2 mW
Laser wavelength
630 – 660 nm
Laser class
Class 2
Power supply
9 V compound (e.g. 6LR61)
Operating temperature
-10 °C – 40 °C
Page 3
ProfiScale CROSS PS 7500 3
Printing and typesetting errors excepted. We reserve the right to make technical changes.
Operating the device
Replacing the battery
1. Ensure that the laser is switched off.
2. Replace the 9 V compound battery, observing the
correct polarity.
3. Close the battery compartment cover.
Securing the device
A The device can be secured in different ways:
Pin fixing (as in Fig. 1 and Fig. 2)
B Securing using adhesive points (as in Fig. 4)
C The device can also be mounted using tripod STAND PS 7510.
Use the angle adapter to mount the device.
Using the device
1. Position the device.
2. Switch on the device and open the locking switch.
The device adjusts itself automatically.
Automatic adjustment
The automatic adjustment only works if the device is
suspended. The device centres itself within a range of ±8 °.
If the device is being transported, you must move the locking
switch to the lock position.
Tips:
This device projects lines on surfaces on which or in front of which the device
was positioned. If the laser lines are not visible even though the device is
switched on, check the battery. The device was designed for indoor use.
Disposing of the device
Dear Customer,
Please help to reduce waste. Should you decide to dispose of the device,
please bear in mind that many of the components it contains are made from
valuable material that can be recycled.
Please do not throw the device into the normal waste bin. Contact the
responsible office in your area and ask about collection points for electrical
waste.
Loading...