Bunn-O-Matic 1.0 Gallon TF SERVER, 1.5 Gallon TF SERVER Operation Manual

Download

Page 1

1.0 & 1.5 Gallon

TF SERVER

(With & Without Base)

USE & CARE INFORMATION

CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE 1 of DAILY CLEANING.

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

Page 2

INTRODUCTION

This server is intended for use with a BUNN® DUAL® TF DBC, SINGLE® TF DBC or ICB coffee brewer only. When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf.

USER NOTICES The notices on this server should be kept in good condition. Replace unreadable or damaged labels.

#26186.0000

DAILY CLEANING

CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY

NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method

consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing solution using an approved non-chlorine sanitizer. Do not submerge server.

1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server completely by opening the faucet.

2. Remove the lid, ﬁll server with cleaning solution and thoroughly clean the inside of server.

3. Rinse server thoroughly using fresh water rinse.

4. Fully ﬁll server with sanitizing solution for 5 minutes then drain through fully open faucet.

5. Remove the large plastic cover from the bottom of the server, then remove the clamps and silicone tube from the server.

6. Remove the faucet handle/stem assembly by unscrewing the faucet nut just beneath the faucet handle.

7. Remove sight gauge shroud by pulling straight up. Remove sight gauge tube, nut, ferrule and o-ring.

8. Use enclosed cleaning brush to thoroughly clean the ﬁll tube of the lid assembly, faucet, and sight gauge tube.

9. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts, lid, and silicone tube in a mild detergent and water solution. Rinse the parts in hot water. Sanitize the parts for ﬁve minutes, then air dry completely.

10. Reassemble the faucet and attach it, the lid, sight gauge and silicone tube to the dispenser.

11. Wash the entire outside surface of the server with a clean damp cloth.

35075 111604

Page 3

SERVER WITH BASE

REPLACEMENT PARTS

1. 35006.1000 Shroud, Sight Gauge 1.5 Gal. (Includes Item 4)

35006.1001 Shroud, Sight Gauge 1.0 Gal. (Includes Item 4)

2. 35010.0000 Plate, Decal Mounting

3. 35009.0000 Decal, Bunn

4. 35004.0000 Backing, Sight Gauge 1.5 Gal.

35004.0001 Backing, Sight Gauge 1.0 Gal.

5. 35005.0000 Sight Gauge Tube 1.5 Gal.

35005.0001 Sight Gauge Tube 1.0 Gal.

6. 39306.1001 Nut w/Ferrule

8. 23408.0001 O-Ring, Sight Gauge Tube

9. 35015.0000 Handle, Faucet

10. 35003.0000 Nut, Faucet Spout

11. 00601.0000 Faucet Spring

12. 29164.0000 Faucet Stem

13. 00600.0000 Faucet Seat Cup

14. 35074.0000 Screw, Hex Hd Black M4 x .7x25

15. 35002.0000 Spout, Faucet

16. 35014.0000 Cover, Drip Tray

17. 35008.0000 Drip Tray

18. 26186.0000 Decal, Warning Hot Liquid

19. 35001.0000 Guard, Faucet

20. 12422.0006 Clamp, Tube .53"/.59" I.D.

21. 35342.0000 Tube, Silicone

22. 12422.0001 Clamp, Tube .59"/.66" I.D.

23. 35016.0000 Insert, Stand

24. 34999.0000 Stand, Server

25. 01383.0002 Screw, Pan Head #6-32 x .62"

26. 35007.0000 Base Plate, Stand

27. 04811.0000 Foot, Rubber-Black .62" Dia.

28. 35301.0000 Brush, Cleaning

29. 35071.0000 Decal, Black Wrap (Black Decor models only)

30. 35365.0000 Lid Assembly 1.5 Gal.

35365.0001 Lid Assembly 1.0 Gal.

35075 031309

Page 4

SERVER WITHOUT BASE

REPLACEMENT PARTS

1. 35006.1000 Shroud, Sight Gauge 1.5 Gal. (Includes Item 4)

35006.1001 Shroud, Sight Gauge 1.0 Gal. (Includes Item 4)

2. 35010.0000 Plate, Decal Mounting

3. 35009.0000 Decal, Bunn

4. 35004.0000 Backing, Sight Gauge 1.5 Gal.

35004.0001 Backing, Sight Gauge 1.0 Gal.

5. 35005.0000 Sight Gauge Tube 1.5 Gal.

35005.0001 Sight Gauge Tube 1.0 Gal.

6. 39306.1001 Nut w/Ferrule

8. 23408.0001 O-Ring, Sight Gauge Tube

9. 35015.0000 Handle, Faucet

10. 35003.0000 Nut, Faucet Spout

11. 00601.0000 Faucet Spring

12. 29164.0000 Faucet Stem

13. 00600.0000 Faucet Seat Cup

14. 35074.0000 Screw, Hex Hd Black M4 x .7x25

15. 35002.0000 Spout, Faucet

16. 26186.0000 Decal, Warning Hot Liquid

17. 35001.0000 Guard, Faucet

18. 12422.0006 Clamp, Tube .53"/.59" I.D.

19. 35342.0000 Tube, Silicone

20. 12422.0001 Clamp, Tube .59"/.66" I.D.

21. 35301.0000 Brush, Cleaning

22. 35071.0000 Decal, Black Wrap (Black Decor models only)

23. 35365.0000 Lid Assembly 1.5 Gal.

35365.0001 Lid Assembly 1.0 Gal.

35075 031309

Page 5

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:

1) All equipment other than as speciﬁed below: 2 years parts and 1 year labor.

2) Electronic circuit and/or control boards: parts and labor for 3 years.

3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.

4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years or 30,000 pounds of coffee, whichever comes ﬁrst. These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Ofﬁce Box 3227, Springﬁeld, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN

are not authorized to make modiﬁcations to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon. If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods speciﬁed above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost proﬁts, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

BrewWISE, BrewLOGIC, BrewMETER, BrewWIZARD, Bunn Gourmet, BUNN Gourmet Ice, BUNN Pour-O-Matic, BUNN, Bunn-OMatic, Bunn-O-Matic, BUNNlink, BUNNserve, BUNNSERVE, BUNN Espress, Cool Froth, DBC, Dr. Brew, Dual, EasyClear, EasyGard, Easy Pour, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, IMIX, Infusion Series, Intellisteam, Quality Beverage Equipment Worldwide, The Mark of Quality in Beverage Equipment Worldwide, My Café, PowerLogic, Safety-Fresh, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, System III, ThermoFresh, 392, AutoPOD, AXIOM, Beverage Proﬁt Calculator, Beverage Bar Creator, BUNNsource, Coffee At Its Best, Digital Brewer Control, Nothing Brews Like a BUNN, Pouring Proﬁts, Pulse Wave, Signature Series, Smart Heat, Tea At Its Best, The Horizontal Red Line, Titan, Ultra, are either trademarks or registered trademarks of Bunn-O-Matic Corporation.

35075 012609