Bunn Coffee Maker TF SERVER 1.5 Installation Manual

ThermoFresh

BUNN

11/2 Gallon Server

OPERATING INSTRUCTIONS

INTRODUCTION

This server allows portable storage and dispensing of up to 11⁄2 gallons of hot beverage at remote locations. Coffee can be brewed directly into the server without removing the cover when used with a BUNN® Dual®-TS or Single®-TS coffee brewer. The spill-resistant design lessens the chance of hot beverage burns and splashes.

USING THE SERVER

Simply follow the FILLING and DISPENSING steps on the back of the server or on the decal shown below.

USER NOTICES

The notices on this server should be kept in good condition. Replace unreadable or damaged labels.

CAUTION

HOT

LIQUID

DO NOT USE ON OPEN FLAME OR ELECTRIC ELEMENTS.

DO NOT CLEAN WITH BLEACH.

DO NOT IMMERSE SERVER

#26186.0000

OPERATING INSTRUCTIONS

NOTE - Preheat server with hot water for best performance.

FILLING

Unscrew and remove top cap. Open sight gauge valve. Position server with brew-thru lid

beneath the brew funnel. Fill with no more than 1.5 gallons of liquid

or no higher than the bottom of fill port. Close sight gauge valve. Reinstall top cap. Do not overtighten.

DISPENSING

Loosen top cap approximately 1 turn to provide vent. Open sight gauge valve. Dispense as desired.

Top Ca

TS N R

EM L

N W

LEA

T I

NO O

ERV

U A C

IQ L

Sight Gauge Valve

Sight Gauge Valve - open

Sight Gauge

Valve - closed

#26180.0000

BUNN-O-MATIC␣ CORPORATION

POST OFFICE BOX 3227, SPRINGFIELD, ILLINOIS 62708-3227

TELEPHONE: (217) 529-6601 FAX: (217) 529-6644

CLEANING

1. Turn the entire lid assembly one-quarter turn counterclockwise to remove it for daily dishwasher cleaning.

NOTE -Bunn-O-Matic recommends CASCADE® dishwashing detergent for thorough cleaning. DO NOT use bleach.

CASCADE® is a registered trademark of Procter & Gamble Co., Cincinnati, Ohio.

2. Completely disassemble the lid assembly for cleaning by removing the inlet tube assy (a) and inlet ball (b) from the bottom of the assembly.(See illustration at left.) The inlet tube assy is removed by unscrewing it in a counterclockwise direction.

3. Clean the airvent (c) of the lid assembly with a small brush. (See illustration at right.)

4. After cleaning, reassemble the lid assembly, being care-

ful to reinstall the ball and inlet tube assy.

NOTE␣ –␣ Be Careful not to lose the ball. It is necessary for the

lid to function properly.

5. Clean all other surfaces with a damp cloth rinsed in any mild, non-abrasive, liquid detergent.

6. Clean the sight gage with a brush. brush.

7. Thoroughly rinse the entire server after cleaning.

WARRANTY

Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects in material and workmanship existing at the time of manufacture and appearing within one year from the date of installation. This warranty does not apply to any equipment, component or part that was not manufactured by Bunn or that, in Bunn’s judgement, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of Bunn are not authorized to make

modifications to this warranty or to make additional warranties that are binding on Bunn. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon.

The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at (217) 5296601 or by writing to Post Office Box 3227, Springfield, Illinois, 62708-3227. If requested by Bunn, the Buyer shall ship the defective equipment prepaid to an authorized Bunn service location. If Bunn determines, in its sole discretion, that the equipment does not conform to the warranty, Bunn shall repair the equipment with no charge for parts during the one year warranty period and no charge for labor by a Bunn Authorized Service Representative during the one year warranty period. If Bunn determines that repair is not feasible, Bunn shall, at its sole option, replace the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AS SPECIFIED HEREIN, TO REPAIR OR, AT BUNN’S SOLE OPTION, REPLACEMENT OR REFUND. Bunn shall not be liable for any

other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.