This equipment will automatically brew a 48 ounce batch of coffee into an awaiting decanter and has
a pour-over feature for emergency use. It is only for indoor use on a sturdy counter or shelf.
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects in material and
workmanship existing at the time of manufacture and appearing within one year from the date of installation. This warranty does
not apply to any equipment, component or part that was not manufactured by Bunn or that, in Bunn’s judgement, has been affected
by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. The agents, dealers or employees of Bunn are not authorized to make modifications to this warranty
or to make additional warranties that are binding on Bunn. Accordingly, statements by such individuals, whether oral or written,
do not constitute warranties and should not be relied upon.
The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by
writing to Post Office Box 3227, Springfield, Illinois, 62708-3227. If requested by Bunn, the Buyer shall ship the defective
equipment prepaid to an authorized Bunn service location. If Bunn determines, in its sole discretion, that the equipment does not
conform to the warranty, Bunn shall repair the equipment with no charge for parts during the one year warranty period and no charge
for labor by a Bunn Authorized Service Representative during the one year warranty period. If Bunn determines that repair is not
feasible, Bunn shall, at its sole option, replace the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS
EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AS SPECIFIED HEREIN, TO REPAIR
OR, AT BUNN’S SOLE OPTION, REPLACEMENT OR REFUND. Bunn shall not be liable for any other damage or loss, including,
but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time,
cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.
The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels.
!
WARNING
Fill water tank before turning -on
thermostat or connecting appliance
to power source.
Use only on a properly protected
circuit capable of the rated load.
Electrically ground the chassis.
Follow national/local electrical codes.
CAUTION - Do not plug-in the brewer until specified in Initial Set-Up.
The A10 Automatic Brewer has an attached cordset and requires 2-wire grounded service rated 120
volts ac, 10 amp, single phase, 60 Hz.
The A10A Automatic Brewer has an IEC 320 connector and matching cordset and requires 2-wire
grounded service rated 230 volts ac, 10 amp, single phase, 50-60 Hz. The appropriate cordset connector
must be supplied when installing the brewer.
PLUMBING REQUIREMENTS
This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi
from a 1/2" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a
regulator in the line when pressure is greater than 90 psi to reduce it to 50 psi.
1
/4" flare.
NOTE – Bunn-O-Matic recommends 1/4" copper tubing for installations of less than 25 feet and 3/8" for more
than 25 feet from the 1/2" water supply line. At least 18 inches of an FDA approved flexible beverage
tubing, such as reinforced braided polyethylene or silicone, before the brewer will facilitate movement
to clean the countertop. It can be purchased direct from Bunn-O-Matic (part number 00326-0000).
This equipment must be installed to comply with the Basic Plumbing Code of the
Building Officials and Code Administrators International, Inc. (BOCA)
and the Food Service Sanitation Manual of the Food and Drug Administration (FDA).
The water inlet fitting is
Plumbing Hook-Up
1.Attach the flare fitting from the short piece of tubing on the flow control (supplied) to the water inlet fitting
on the left rear side of the brewer.
2.Flush the water line and securely attach it to the flare fitting on the strainer.
3.Turn on the water supply.
INITIAL SET-UP
CAUTION – The brewer must be unplugged throughout the initial set-up, except when specified in the
instructions.
1.Insert an empty funnel into the funnel rails.
2.Place an empty decanter under the funnel.
3.Pour three pitchers of tap water into the screened area on top of the brewer. Allow approximately two
minutes between pitchers for water to flow into the tank. While the third pitcher of water is entering the
tank, the tank will fill to capacity and the excess will flow from the sprayhead, out of the funnel, and into
the decanter.
4.When the flow of water from the funnel stops, plug-in the brewer and place the heater switch on the
left side of the brewer in the “ON” lower position. Wait approximately twenty minutes for the water in
the tank to heat to the proper temperature. Some water will drip from the funnel during this time; this
is due to expansion and should not occur thereafter.
5.Empty the decanter, return it to the warmer, place the warmer switch in the “ON” (lighted) position, and
momentarily press and release the start switch.
6.Place the warmer switch in the “OFF” (unlighted) position after water has stopped flowing from the
funnel, and let the water in the tank reheat to the proper temperature.
7.Empty the decanter, place the warmer switch in the “ON” (lighted) position, and momentarily press and
release the start switch. Check the water volume in the decanter after water has stopped flowing from
the funnel. It should be 48 ounces.
INITIAL SET-UP (CONT.)
8.If not, locate the brew timer near the heater switch on the left side of the brewer, adjust the brew timer
dial up-or-down as required and allow the water to reheat. Start, and measure another brew cycle.
9.Repeat step 8 until 48oz water volume is achieved.
10. The brewer is now ready for use in accordance with the coffee brewing instructions.
OPERATING CONTROLS
Warmer Switch
Placing the switch in the unlighted position cuts power to the brew station warmer and stops brewing.
Stopping a brew cycle after it has been started will not stop the flow of water into the funnel until the tank
syphons down to its proper level. Placing the switch in the lighted position supplies power to the brew station
warmer and enables the brew circuit.
Start
Momentarily pressing and releasing this switch starts a brew cycle when the warmer switch is in the
lighted position.
NOTE – The warmer switch must be in the lighted position to initiate and complete a brew cycle.
Full/Half
Placing this switch in the half position yields approximately 24 ounces.
COFFEE BREWING
1.Insert a BUNN® filter into the funnel.
2.Pour the fresh coffee into the filter and level the bed of grounds by gently shaking.
3.Slide the funnel into the funnel rails.
4.Place an empty decanter under the funnel.
5.Place the warmer switch in the lighted position. Momentarily press and release the start switch.
6.When brewing is completed, simply discard the grounds and filter.
CLEANING
1.The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning
all surfaces on Bunn-O-Matic equipment.
2.Check and clean the sprayhead. The sprayhead holes must always remain open.
3.With the sprayhead removed, insert the deliming spring (provided) all the way into the sprayhead tube.
When inserted properly, no more than two inches of spring should be visible. Saw back and forth five
or six times.
NOTE – In hard water areas, this may need to be done daily. It will help prevent liming problems in the
brewer and takes less than a minute.
REPLACEMENT PARTS
04060.0000 ........... BASE EXTRUSION
04040.0004 ........... BREW FUNNEL, BLACK
04069.0003 ........... CONTROL THERMOSTAT ASSY.
01716.0000 ........... CORD, POWER 250V 10 AMP, IEC320 (A10A)
01637.0000 ........... CORDSET, 16/3HSJO NEMA 5-15P (A10)