Buffalo Technology WBR2-G54S User Manual

Page 1
Wireless Cable/DSL Router
www.buffalotech.com/wireless
User Manual
125 High Speed Mode*
WBR2-G54S
Page 2
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
Antenna Installation. . . . . . . . . . . . . . . . . . . . . . 13
Standard Settings . . . . . . . . . . . . . . . . . . . . . . . 14
AOSS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . 26
Wireless Settings . . . . . . . . . . . . . . . . . . 26
Wireless LAN Security . . . . . . . . . . . . . . 28
LAN Port . . . . . . . . . . . . . . . . . . . . . . . . 32
DHCP Server . . . . . . . . . . . . . . . . . . . . . 33
Wireless MAC Filtering . . . . . . . . . . . . . 36
Wireless Bridge (WDS) . . . . . . . . . . . . . 38
WAN Settings . . . . . . . . . . . . . . . . . . . . . . . 40
WAN Port . . . . . . . . . . . . . . . . . . . . . . . . 40
WAN Network . . . . . . . . . . . . . . . . . . . . . 43
LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . 26
2
Page 3
Table of Contents
Network Settings. . . . . . . . . . . . . . . . . . . . . 45
Routing Setup . . . . . . . . . . . . . . . . . . . . 45
Address Translation . . . . . . . . . . . . . . . . 47
Packet Filter . . . . . . . . . . . . . . . . . . . . . . 50
Intrusion Detector . . . . . . . . . . . . . . . . . 55
UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Management . . . . . . . . . . . . . . . . . . . . . . . . 58
System Information . . . . . . . . . . . . . . . . 58
Change Password . . . . . . . . . . . . . . . . . 59
Time Setup . . . . . . . . . . . . . . . . . . . . . . 60
Traffi c Information . . . . . . . . . . . . . . . . . 61
Client Monitor . . . . . . . . . . . . . . . . . . . . 62
Ping Tool . . . . . . . . . . . . . . . . . . . . . . . . 63
Log Information . . . . . . . . . . . . . . . . . . . 64
Syslog Transfer . . . . . . . . . . . . . . . . . . . 65
Save/Restore Settings . . . . . . . . . . . . . . 66
Reboot/Reload Settings . . . . . . . . . . . . . 67
Firmware Updates . . . . . . . . . . . . . . . . . 68
AOSS . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
3
Page 4
Table of Contents
Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . 71
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 76
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . 90
Warranty Information. . . . . . . . . . . . . . . . . . . . . 93
Contact Information . . . . . . . . . . . . . . . . . . . . . 94
4
Page 5
Introduction
AirStation 125 High Speed Mode Wireless Cable/DSL Router (WBR2-G54S)
This manual introduces you to the AirStation Cable/DSL Router, and will help you connect to your network quickly.
The WBR2-G54S router, is a wireless 4-port router network device that complies with the 2.4GHz IEEE 802.11g standard specifi cation on wireless LANs. It also supports 125 High Speed Mode technology. The WBR2-G54S supports enhanced built-in NAT/SPI fi rewall functions and is used as a multi-functional router/link between wired and wireless LAN computers.
Summary of the AirStation WBR2-G54S features:
• Wi-Fi™ (Wireless Fidelity) certifi ed by the Wi-Fi Alliance as an 802.11b/g device. AirStation will communicate with other IEEE 802.11b/g/Wi-Fi compliant wireless LAN products.
• Supports 125 High Speed Mode
• Support for Wi-Fi Protected Access™ (WPA), 802.1x, TKIP, AES, and WEP.
• Supports Frame Bursting for enhanced performance.
• DHCP client/server function.
• Auto roaming, supports seamless roaming over multiple channels.
• VPN pass-through, for secure communications.
• Packet Filtering for eliminating unwanted communications.
• SOHO/SMB routing and fi rewall functions provide a safer private networking environment, includ­ing support for MS NetMeeting and MSN-Messenger.
5
Page 6
Introduction
• Additional SPI Firewall Functions - DMZ, intrusion detection and notifi cation
• Syslog transmits some or all system activities to a central Syslog server.
• Extended range, with optional add-on antennas or WDS (Wireless Distribution System).
• Auto Media Dependent Interface/Crossover (MDI/X) port, allows connection by standard and crossover CAT5 cables.
• Supports Universal Plug and Play (UPnP).
• Buffalo’s AOSS System for easy, secure wireless client confi guration.
• Enhanced security features:
- SPI Firewall and DMZ zone functions to prevent unknown intruders.
- Intrusion Detector Firewall (NAT) with a pop-up or email alert warning unwanted attacks.
- Dynamic packet fi ltering.
- WPA, 802.1x, TKIP, AES, and WEP.
- VPN (IPSec, PPTP and L2TP) pass-through
- Packet monitoring and fi ltering by MAC address, IP address and port.
- PPPoE support
- WDS support
• Buffalo’s easy web interface confi guration
• Broadband router static and dynamic routing methods between WAN and LAN based on updated routing tables. An economical way to bridge multiple networks.
6
Page 7
Introduction
• Optional external antennas for boosting range and signal quality.
• Buffalo’s AOSS System for easy, secure wireless client confi guration.
Home Networking 1
Buffalo AirStation wireless access points enable sharing broadband by simply connecting the AirStation to a DSL or Cable modem to:
• Share fi les and printers
• Access and share the Internet
• Share media fi les
SOHO/SMB Networking
With high-speed DSL or Cable connections readily available, many users can work effectively from a home offi ce, connected securely to a corporate network. Buffalo’s solutions are ideal for home networks that require secure, high-speed access to the corporate LAN. Tools that play an integral part in Buffalo’s solutions include VPN connectivity for secure access to corporate resources, which enable the remote employee to handle information from clients or coworkers as if they were in the offi ce. Connect the Buffalo AirStation Broadband router AP to a Cable or DSL modem in order to:
•Share broadband access
•Share fi les and printers
•Bridge between multiple networks and multiple computer platforms
•Provide easy and secure access to home or company networks from remote locations
7
Page 8
Introduction
System Requirements
• Broadband (High-Speed) Internet connection or existing Local area connection
• Any Wi-Fi (wireless) compatible computer with a Web Browser Internet Explorer or Netscape 4.5 or later. (Safari 1.0 is supported with Macintosh OS X.2)
AirStation WBR2-G54S Package Contents
The AirStation WBR2-G54S package consists of the following items.
1. WBR2-G54S Base Station
2. AC adapter and power cable
3. CAT5 LAN cable
4. Utility CD with Manual
5. Quick Setup Guides
6. Warranty Statement
8
Page 9
The LAN or Wired MAC address is the default SSID (SSID) of the AirStation. The LAN MAC address is clearly labeled on the back of the AirStation.
Product Views
Power - Lit when the device is powered on.
Wireless - Lit when the wireless radio is on. Flashes when
wireless traffi c is present.
WAN - Lit when connection to Cable/DSL modem is present.
Flashes when internet traffi c is present.
Diag - Flashes red when performing diagnostic functions.
AOSS - Flashes when in AOSS mode, solid when AOSS
encryption has been set.
Ethernet - 1, 2, 3, or 4 lit when ethernet clients are connected. Flashes when ethernet traffi c is present.
Introduction
9
Page 10
Introduction
About the AirStation CD
The AirStation does not require any software to be installed on your computer for confi guration. The AirStation CD contains client drivers for Buffalo Wireless Adapters (i.e. Notebook Adapter and Desktop PCI Adapter) and the AirStation documentation.
Prior to copying or installing any software, please read the Software License Agreement “license. txt”, located in the root folder of the CD. By installing, copying or using the AirStation software, you are consenting to the terms of this agreement. If you do not agree to all of the terms of the Software License Agreement, do not download, copy or install the AirStation software.
It is the policy of Buffalo Technology to improve products as new technology, components, software and fi rmware become available.
Please consult the AirStation wireless website (http://www.buffalotech.com/wireless) to download and install the latest fi rmware for your product.
10
Page 11
Installation / Setup
Follow these simple steps to connect the AirStation to your Broadband Internet connection allowing you to combine and share wired and wireless computers and printers with the high-speed internet connection.
1. Power down the Cable or DSL modem and the computer which will be used to confi gure the AirStation router.
2. Plug the Cable or DSL’s LAN Ethernet cable into the AirStation’s WAN port. Initially, you may need to unplug this cable from your computer, hub or other router.
3. Plug the provided Ethernet cable into a LAN port on the AirStation and plug the other end into
your computer Ethernet adapter’s (NIC) port. If you plan to initially confi gure the AirStation via a wireless connection, (not recommended), you may skip this step.
4. Power on your cable or DSL modem, wait one full minute, Power on the AirStation router, wait another full minute and then power on the computer which will be used to confi gure the AirSta­tion. If the red DIAG light on the AirStation is lit or fl ashing after several minutes of being pow­ered on, please consult Buffalo Technical Support.
11
Page 12
Installation / Setup
Introduction
Confi guring the AirStation using a standard web browser requires basic wireless confi guration knowledge. Setup includes manual wireless confi guration and basic administrative management.
Setup Preparation
Make note of the AirStation’s wired MAC address (found on the back of the WBR2-G54S). It is also recommended you record any other broadband ISP information such as global IP address, subnet mask address, default gateway address, DNS server address and PPPoE parameters.
Setup Overview
Buffalo recommends using a wired connection, meaning your computer is physically connected to the AirStation with a CAT5 straight cable plugged into one of the four LAN ports This type of setup will eliminate possible setup problems due to any issues with the wireless adapter on the computer being used to confi gure the AirStation.
A Web browser version 4.5 or later can be used to confi gure the AirStation.
12
Page 13
Antenna Installation
The WBR2-G54S has two internal antennas. One has a vertical orientation while the other has a horizontal orienta­tion. This setup is ideal because it allows for proper antenna polarization with both desktop and notebook style wireless adapter antennas.
However, it may be necessary to increase your range further by installing an external, higher-gain antenna. External antennas come in all shapes and sizes. Antennas also come with different connectors. The WHR2-G54 has an ‘MC Connector’ on it. Thus, the antenna must also have an MC connector.
To install the antenna, slide the antenna connector door on the back of the WBR2-G54S to the right. This will expose the MC Connector. Attaching the antenna is simple, just insert the antenna’s MC Connector into the WBR2-G54S’s MC Connector and fi rmly push it in until it snaps into place. Once snapped, the antenna’s connector will swivel with ease. It is important not to push the antenna connector in at an angle.
To remove the antenna, pull the antenna connector out. It is important not to pull the antenna connector out at an angle.
13
Page 14
Standard Settings
Advanced settings for security, fi ltering and other features will be explained in later sections.
Open the Setup Screen
• Connect the WBR2-G54S according to the wiring instructions in Section 2.
• The WBR2-G54S has a default LAN IP address of 192.168.11.1 and Subnet Mask of
- A window will open prompting you to enter a User ID and Password.
Enter “root” as the User ID and leave the password fi eld blank.
Note: These are the factory default settings
Initial
Settings
Login
255.255.255.0.
Note: The computer used to confi gure the AirStation should be set to obtain an IP address automatically using a DHCP server. The Quick Setup Guide enclosed with the product contains detailed instruc­tions on how to confi gure your computer for initial confi guration.
On the computer used to confi gure the AirStation, launch a Web Browser 4.5 or later.
- Enter 192.168.11.1 into the URL fi eld.
14
Page 15
Standard Settings
Initial
Settings
Screen
Initial DSL
button
Screen
Enter ISP information
• Click the appropriate button to select the type of broadband access. (Users more experienced in networking may choose to select the Ad­vanced button and skip to Section 4.)
• For supplementary tools, use the tabs along the top of the screen.
DSL Button
Select the appropriate connection method.
Automatic IP Assignment by ISP
- The DHCP server of the ISP assigns an IP ad­dress automatically.
15
Page 16
Standard Settings
Manual DSL
IP Settings
Screen
DSL PPPoE
Settings
Screen
Enter IP Address Manually
- Enter the IP Address given by the ISP.
- Use ‘Enter IP Address Manually’ if the ISP requires use of a static IP address.
PPPoE Connection
- Enter the PPPoE information provided by the ISP.
16
Page 17
Standard Settings
Initial CATV
Settings
Screen
Manual IP
Address
Settings
CATV (Cable) Button
Select the appropriate connection method.
Automatic IP Assignment by ISP
- Select ‘Automatic IP Assignment by ISP’ if your ISP’s DHCP server assigns an IP address automatically.
Enter IP Address Manually
- Select ‘Enter IP Address Manually’ if the ISP requires use of a static IP address.
17
Page 18
Standard Settings
Auto IP/
Manual DNS
Settings
Line
Test Tab
The IP Address is Acquired Au to mat i cal ly but DNS Server Address is Entered Manually
-
Select ‘IP address is acquired automatically but DNS server address is entered manually’ if the ISP’s DHCP server supplies an IP address but not DNS server addresses.
Line Test
Tests the connection to the Internet.
18
Page 19
Standard Settings
Security Tab
Security
The Security Tab offers three Simple Security Settings. Follow the in struc tions in each screen to enter Encryption Keys, MAC Address Filter­ing and the degree of fi rewall security for the AirStation.
19
Page 20
Standard Settings
Encryption Setup.
- Select the desired encryption scheme from the choices. After it has been selected, press the ‘Next’ button. You will then be prompted to enter the appropriate key(s) for that method of encryp­tion.
Simple MAC Address Filter.
- Select ‘Enable’ to use MAC fi lter­ing. See ‘Page 36’ for more infor­mation on MAC Address Filtering.
20
Simple Security Setup.
- See ‘Page 55’ for more information on Intrusion Detector.
Page 21
Standard Settings
Ap pli ca tion
Ta b
Applications
The Application Tab offers setup for special ap­plications such as games, MS NetMeeting and MSN Messenger. Then follow the on-screen menus to confi gure the AirStation for the applica­tion.
21
Page 22
Standard Settings
Internet Gaming Setup
-Enter the ports(refer to Game documentation) the game runs on, and enter the Local IP Ad­dress of the PC that plays the game.
NetMeeting Setup
-Enter the IP Address of the PC that will use Netmeeting.
MSN Messenger Setup
-Refer to the on-screen help for information about Messenger.
Although your AirStation will function fi ne using only the Standard Settings, you may wish to explore more advanced options. The Advanced Settings section explains each function in the Advanced settings area.
Click the Top tab and click the Advanced button to enter the Advanced settings area.
22
Page 23
AOSS
AOSS (AirStation One-Touch Secure System) is a simple, one-touch setup for connecting wireless clients to an access point while setting up the most secure possible connection. Users no longer need to worry about choosing the proper security protocols, IP addresses, or SSID's. The intelligence of AOSS determines the most optimal connection and confi gures itself in seconds.
NOTE: AOSS automatically creates a secure connection between your AOSS Access Point and client. You must have a Buffalo AOSS enabled wireless client device to use the AOSS features of your AOSS Access Point/Router.
Confi gure your WBR2-G54S’ internet con-
nection by referring to the instructions in the WBR2-G54S’ Quick Setup Guide.
Once the WBR2-G54S has been confi g-
ured, follow the directions to install your wireless client device and its drivers if necessary. Certain wireless client adapt­ers require client software to confi gure them. If your device has a Client Man­ager, then install it as well.
NOTE: If the wireless client adapter is installed on a PC, then the AOSS client manager will need to be installed as well. If your wireless client adapter is a standalone device that does not require a PC, then just power up the device.
Standalone Devices: Ethernet Converters and Access Point Bridges Client Manager Devices: CardBus, USB, and PCI Adapters.
Standalone
AOSS Device
23
Client Manager
Device
Client Manager
Software
Page 24
AOSS
Now that the WBR2-G54S and wireless client adapter
are installed, you can use AOSS to confi gure them.
To begin the confi guration, press the AOSS button on
the back of the WBR2-G54S for 3-5 seconds. The AOSS light will begin to fl ash when the AOSS mode has been enabled. You can stop pressing the button at this point.
NOTE: AOSS mode will stay active for a period of two minutes. This is the time-slot required to initiate the
wireless client adapter. The AOSS LED will stop fl ashing when AOSS mode has stopped or timed out.
Refer to your wireless client adapter's AOSS
supplement to initiate the wireless client adapter's AOSS mode.
It typically takes 10-15 seconds for the AOSS light to
stop fl ashing after the AOSS button has been pressed on the wireless client adapter. Once confi guration is complete, the AOSS light will remain steady. Please refer to your wireless client adapter's supplement for the remainder of the setup.
24
Page 25
AOSS
Additional AOSS Information:
Only one AOSS wireless client adapter can be confi gured to the AOSS router at a time. Thus,
the button will need to be repressed for each additional AOSS wireless client adapter that will be connected.
It is not necessary to AOSS client devices that have already been confi gured via AOSS, unless
signifi cant changes have been made to the wireless network.
Do not attempt to confi gure two separate AOSS networks at the same time, as it may cause
undesired confi gurations.
If an undesired client has connected via AOSS, it can be disconnected from within the WBR2-
G54S’ advanced confi guration menus.
25
Page 26
Advanced Settings
LAN Settings
Wireless
Settings
ters for the SSID (case sensitive). By default the SSID is the LAN Mac address of the AirStation.
Note: Roaming - When multiple AirStations have an identical SSID, WEP key (if WEP is used), (and channel in WDS mode) , client computers may Roam between the AirStations.
Wireless Channel - Select the channel used for wireless communication. There are 11 overlap­ping channels. Channels 1, 6 and 11 are non-overlapping. The ‘Auto-Channel’ option is recom­mended, as it constantly assesses the best available channel for the AirStation to operate on.
26
Set up LAN connections.
Wireless Settings
Wireless Function - Enable or
disable wireless LAN computer communication.
SSID - Allows administrator to alter the SSID of the AirStation. To communicate with a specifi c AP only, the AP’s SSID must be entered in the client comput­er. The client computer looks for the specifi c AP (or SSID) for wireless communication. Use up to 32 al pha nu mer ic charac-
Page 27
Advanced Settings
If there are multiple APs in close proximity using the same channel, there may be interference. In this case, change to a non-overlapping channel.
Privacy Separator - Enable or disable communication between wireless clients. If you choose to use this feature, every wireless client that is associated to the AirStation will not be able to communicate with any other wireless clients.
Note: If this function is used, wired clients can still communicate with wireless clients.
BSS (Basic Service Set) Basic Rate Set - The transmission data rates offered by the AirStation. It is recommended to use the ‘Default’ selection to accomidate 802.11 and 802.11b rate sets. It is NOT recom­mended to use the ‘All’ selection, as some devices may not understand all of the rate sets offered by the AirStation.
Frame Bursting - This function increases 802.11g communication throughput by transferring packets more effi ciently. The following conditions affect this function:
• The wireless LAN client adapter must support Frame Bursting (and it must be enabled). If the wireless LAN client adapter does not support Frame Bursting, or Frame Bursting is not enabled, then it will operate at non-Frame Bursting speeds.
125 High Speed Mode - This function further increases 802.11g communication. Rate sets up to 125 Mbps are offered to clients.The following conditions affect this function:
• The wireless LAN client adapter must support 125 High Speed Mode (and it must be enabled). If the wireless LAN client adapter does not support 125 High Speed Mode, or it is not enabled, then it will operate at regular 802.11g speeds.
It is recommended to leave 125 High Speed Mode enabled as it can only help throughput, not hurt it.
27
Page 28
Advanced Settings
802.11g Protection - This enables protection mechanisms for when 802.11b clients join the net­work. It enables CTS (Clear-to-Send)
DTIM Period - An access point transmits beacon signals to nearby clients at a preset interval. This parameter sets the beacon transmission interval time (1-255 seconds). Se lec tion of a larger num­ber may conserve energy for the client computer (when client power management is enabled), but may delay wireless communication. The default value of 1 is recommended.
Wireless Output Power - Confi gure output power of the AirStation. Decrease wireless output power to shrink the wireless communication range. The default setting of 100% is recommended unless decreased range is desired
Wireless
Security Settings
Wireless LAN Security
Broadcast SSID - Enable or Dis-
able the SSID (SSID) from being broadcasted. If denied, the AirStation will not be found unless the specifi c AirStation’s SSID is entered in the client computer manually.
Data Encryption - Disable to have no encryption of the wireless data. This will make accessing the AirStation and the network very easy. It is im-
28
Page 29
Advanced Settings
portant to note, that without encryption it is easy for strangers to connect to your network, especially if the AirStation is broadcasting its SSID.
Select the type of data encryption:
• Disabled - Disable data encryption.
- WEP - Uses WEP encryption. Encryption key should be entered.
- TKIP - Uses TKIP (Temporal Key Integrity Protocol) for data encryption.
The encryption key is renewed every “Re-key interval” when “TKIP” is selected.
WEP - When the WEP (Wired Equivalent Protection) encryption standard is implemented into a wireless network, a WEP key is used between the client and access point to successfully encrypt, transmit and decrypt data. For this reason, the same WEP key must be used for communication between the client and the AirStation.
An access point and client may both carry multiple WEP keys. It is necessary for not only the WEP keys to match, but also the WEP key’s order. If a wireless client cannot support multiple WEP keys, the AirStations must be confi gured to transmit key number 1 for a connection to take place.
Examples of WEP key:
64-bit ASCII: 5 digits of alphanumeric characters, “ab34Y”
128-bit ASCII: 13 digits of alphanumeric characters, “123456abcdef7”
Note: ASCII WEP keys are case sensitive.
64-bit HEX: 10 digits, using characters 0-9 and a-f, “00234ABCDE”
29
Page 30
Advanced Settings
128-bit HEX: 26 digits, using characters 0-9 and a-f, “20123456789abcdeabcdeabcde”
TKIP - TKIP (Temporal Key Integrity Protocol) is a WEP expanded encryption technique. TKIP has greatly improved WEP’s weaknesses by rotating secret keys between every packet. TKIP uses WPA-PSK (pre-Shared Key).
Characteristics:
- The Initialization Vector is expanded from 24-bits to 48-bits.
- The Initialization Vector is randomized.
- Uses a different RC4 key for every packet.
AES - AES further improves TKIP by using AES (Advanced Encryption Standard) encryption method. Due to its hardware co-processor, AES uses the toughest encryption without sacrifi cing throughput like WEP and TKIP.
TKIP & AES require an 8 to 63 character passphrase in ASCII or 64 digits hexadecimal key.
Example 1: [ airstation -WPA-PSK ]
Example 2: [0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef]
WPA Group Rekey Interval - When TKIP is selected, the encryption key is renewed at this inter­val. This interval is in seconds; the range of acceptable values is 0-3600.
If 0 is entered, the key is never renewed.
Note: The lower the rekey interval, the more often a rekey occurs. Setting a low rekey interval may affect performance negatively.
30
Page 31
Advanced Settings
TKIP Method - This is the method that the AirStation uses to handle TKIP encryption. The two methods are Hardware and Software. Hardware uses the AirStation’s processors TKIP extension to handle the TKIP encryption. This results in decent performance but the limitation of only 12 simulataneous TKIP clients. The software method is a software method written by Buffalo which al­lows for considerably more TKIP clients but does not utilize the processor’s direct extensions. This results in more of a throughput loss when TKIP is used.
IEEE802.1x/EAP authentication (WPA) - Confi gure Authentication and WPA Settings.
Disable - Do not use any RADIUS Server based authentication.
Enable - Authorized clients access this AirStation via a RADIUS Server.
Use 802.1x/EAP to authorize every wireless client who wants to access the AirStation by using
802.1x/EAP and a RADIUS Server. The RADIUS server provides login information for every user establishing a more secure system than TKIP or other fi xed encryption key methods. This also reduces the amount of necessary key maintenance.
A RADIUS server is necessary for IEEE802.1x/EAP authentication. Enter [RADIUS Server], {RA­DIUS Port] and [RADIUS Key] information.
RADIUS authentication
RADIUS Server - Enter RADIUS server IP address. RADIUS Port - Enter port number for authentication. RADIUS Key - Encryption key between RADIUS Sever and the AirStation. Enter the same key as
registered in the server. Use a 1 to 256 character alphanumeric code.
31
Page 32
Advanced Settings
LAN Port
Settings
the IP address is changed, then the DHCP scope must be changed to match.
DHCP Server Function - Allows administrator to enable/disable the DHCP server function for the AirStation LAN side. Select Use to enable and Do not use to disable the function. Once Use is selected, the assigned IP address range can be specifi ed. Enter the starting LAN IP address and total number of computers the DHCP server can accomidate.
Note: If there is another DHCP server on the network, one either must be disabled or the IP range must be changed to avoid confl icts derived from overlapping DHCP scopes.
32
LAN Port
Set the LAN side Ethernet settings.
LAN Side IP Address - Allows ad min is tra tor to specify a static IP and Subnet Mask for the LAN side of the AirStation.
Note: If the AirStation’s IP address is changed, the con­fi guring computer’s IP must be changed to the same range to continue confi guration. If the LAN IP is changed, restart the AirStation. (Section 4.4.10). If
Page 33
Advanced Settings
DHCP Server
Settings
server is turned off, all client PC’s must have unique, static IP addresses and valid network settings manually entered. Check with your LAN administrator for static IP information.
Assigned IP address (Range As sign ment) - Sets the beginning address and range of addresses to be assigned by the AirStation’s DHCP server function. Select up to 253 consecutive addresses (nodes). The IPs to be excluded from the range spec i fi ca tion should be entered in the specifi ed fi eld.
33
DHCP Server
Allows a more advanced con­fi guration of the DHCP server functions.
DHCP Server Function - Al­lows ad min is tra tor to enable/ disable the DHCP server func­tion for the AirStation LAN side. Select Use to enable or Do not use to disable this function. If the DHCP service is enabled, wireless and wired clients may receive IP addresses and other network information from the AirStation. If the DHCP
Page 34
Advanced Settings
Lease duration - Specifi es the time in hours (1-999) an assigned IP address is valid. If the client computer does not request a renewal of IP address before the lease period expires, the AirStation can issue the IP to another client computer.
Default Gateway - Allows administrator to use the Default Gateway address (the AirStation’s IP address), assign a specifi c Gateway address, or block clients from Gateway notifi cation.
DNS server - Allows administrator to use the default DNS address (the AirStation’s IP address), assign specifi c DNS addresses, or block clients from DNS address notifi cation.
WINS server - Allows administrator to use a WINS address. Select auto assignment of the IP ad­dress, enter a specifi c WINS IP address, or block clients from the WINS address notifi cation.
Domain name - Allows administrator to use an assigned domain name, assign a specifi c domain name, or block clients from domain name no ti fi ca tion. Domain names will be sent to LAN comput­ers when an IP address is assigned. Enter a maximum of 64 al pha nu mer ic characters.
34
Page 35
Advanced Settings
Manual IP
and MAC
Address
Assignment
Settings
Manual IP and MAC Address As sign ment - Allows administra-
tor to add additional leased IP addresses tied to a specifi c MAC address. When a specifi c MAC address connects to the AP, the IP address specifi ed will be given to that client.
Display/Delete lease informa­tion - List of IP addresses, MAC addresses, lease periods and status is displayed.
35
Page 36
Advanced Settings
Wireless MAC
Filter
Wireless MAC Filter
Wireless PC’s Connection
- Select Enable to restrict wireless connections to the registered adapters in the list. Select Disable to disable MAC address fi ltering.
Press the Preset button to enter the MAC Address registration menus. This is where MAC Addresses can be assigned and deleted.
36
Page 37
Advanced Settings
Register for
Allowable PC’s
MAC Address
Registration for MAC Ad­dresses - MAC access
restriction set up in LAN. Input the MAC addresses that are allowed to communicate with the AirStation.
MAC address list - Displays a table list of all MAC addresses allowed to communicate with the AirStation.
37
Page 38
Advanced Settings
Wireless
Bridge (WDS)
Settings
Note: All AirStations must support WDS and be on the same channel. Do not use ‘Auto-Channel’ when using WDS. For roaming support, use the same SSID on all devices.
Add a WDS Partnet: Allows administrator to input the wireless MAC address of AirStations for Bridge (WDS) communication. The wireless MAC address is found in the Management section => System Information, labeled Wireless MAC Address.
38
Wireless Bridge (WDS)
The Wireless Distribution System supports peer-to-peer AP communication.
Wireless Bridge (WDS) Func­tion - Select Enable to allow
Bridge (WDS) mode between AirStations or Disable to block communication between AirStations.
Wireless Bridge (WDS) dedi­cated mode - Select Enable to
restrict wireless computer com­munication with the AirStation. In dedicated mode wireless clients CANNOT connect to WDS AirStations.
Page 39
Advanced Settings
Wireless
Bridge (WDS)
Settings
Repeat this process on every other AirStation used in Bridge (WDS) mode.
39
To enable WDS, set the Wire­less Bridge (WDS) function to Enable.
Enter the Wireless MAC address of the AirStation to communicate with in the form of two characters separated by a colon and click Add.
MAC Address Ex: 00:00:00:00:00:00
Up to six AirStation MAC ad­dresses may be registered.
Click Apply under Wireless Bridge (WDS) settings when the wireless Mac addresses AirStation are entered.
Page 40
Advanced Settings
WAN port
Setup
WAN Settings
WAN Port
Wired WAN Performance
- Select port speed and type of duplex connecting to the WAN port. If unknown, select Auto negotiation.
MAC Address of WAN - Set the AirStation MAC address to be used for WAN com mu ni c­a tion. Some ISP’s may require you to set the MAC Address of WAN to be the same MAC address of your cable or DSL modem.
ministrator to select DHCP server, PPPoE, or manual setting for the WAN port of the AirStation.
Auto IP assignment from DHCP server - acquire the IP address automatically from the DHCP server.
Use PPPoE client - If selected, the in for ma tion listed below must be entered.
Manual setting - Enter the appropriate IP address and subnet mask.
40
WAN IP Address - Allows ad-
Page 41
Advanced Settings
PPPoE Setting (for enabling PPPoE Client function) - Allows administrator to use PPPoE as specifi ed by the ISP.
The following parameters should be entered for PPPoE Settings:
Name of Connection - Enter the name of your connection.
User Name - Enter the user name (up to 64 alphanumeric characters) for PPPoE au tho ri za tion.
Password - Enter the password provided by your ISP (up to 64 alphanumeric characters). Reenter
the password in the Confi rmation box.
Service Name - Enter the PPPoE service name (up to 64 alphanumeric characters). If your ISP doesn’t require a service name, then leave it blank.
Connection Type - Select from:
- Continuous Connection - connects im me di ate ly after setting and never disconnects.
- Connect on Demand - Reconnects when the disconnect time elapses.
- Manual - Disables Automatic Con nec tion. Connects to the Internet using the connect button on the initial settings page.
The Enter New Connection button will not appear until Use PPPoE Client is set.
Disconnection Time - Specify the number of minutes (0-1440) before automatic dis con nect is performed. If “0” is entered, the dis con nect function is disabled. If Con tin u ous Connection is selected, the timer is disabled.
41
Page 42
Advanced Settings
PPPoE
Settings
Screen
once per minute. If there is no reply within six minutes, the client disconnects. Set to Disable if frequent disconnection occurs.
Activation - Enable/disable registered connection settings. If disabled, the connection is not per­mitted.
42
Authorization - Authorization method for accessing the ISP’s PPPoE server. If unknown, select Auto authorization.
MTU (Maximum Transmit Unit) Size - Maximum Transmit
Unit (578-1492) when using PPPoE.
MRU (Maximum Receive Unit) Size - Maximum Receive
Unit (578-1492) when using PPPoE.
Keep Alive - Enables the PPPoE client to send a Link Control Protocol (LCP) echo request to the PPPoE server
Page 43
Advanced Settings
Network of
WAN
as sign ment from DHCP Server is selected in the WAN Port section, a gateway IP is assigned automatically, provided the DHCP server is set to provide one.
DNS Server Address - Enter the primary and secondary DNS address(es) of the server to be used by the AirStation for DNS resolution.
If DNS was set to Do not use, leave blank. If Auto IP as sign ment from DHCP Server was selected, DNS addresses are assigned automatically, provided the DHCP server is set to provide them.
43
WAN Network
WAN side (Internet) param­eters. These settings are gen­erally not required if your ISP is providing DHCP services. In this case these fi elds can be left blank if desired.
Host Name - Enter the host name as desired.
Default Gateway - A default gateway IP should be assigned to the AirStation. If unknown, leave blank. If Auto IP
Page 44
Advanced Settings
Remote Management Port Number - Set a specifi c port number when remote setup of the AirSta­tion is planned. Using port 80 allows the AirStation to be accessed from the internet by connecting to http://xxx.xxx.xxx.xxx (where xxx.xxx.xxx.xxx is your WAN IP address). You will need to confi g­ure the NAT (Adress Translation Settings) to forward PORT 80 back to the AirStation.
Block Ping from WAN - Allows a PING test from the WAN/Internet. Select Disable or Enable.
44
Page 45
Advanced Settings
Routing
Setup
information.
Click Add Route to Add a Routing Table Entry
Destination address - Network IP address and subnet mask.
Gateway - Address through which the packet passes before it reaches the des ti na tion address.
45
Network Settings
Routing Setup
RIP transmission to WAN - Allows RIP
transmission or None (no RIP) to WAN
RIP reception from WAN - Allows RIP reception or None (no RIP) from WAN
RIP transmission to LAN - Allows RIP transmission or None (no RIP) to LAN
RIP reception from LAN - Allows RIP reception or None (no RIP) from LAN
RIP transmission to WAN - Allows RIP transmission or None (no RIP) to WAN
Display current information - Allows administrator to view and delete routing
Page 46
Advanced Settings
Add Routing
Table Entry
Metric - Number of routers (1-15) to be passed before the packet reaches its destination.
46
Page 47
Advanced Settings
Address
Translation
Setup
Static IP address translation -When the WAN requests connection to the LAN, the WAN IP
address of the AirStation is translated into the IP address of the LAN computer.
Log Output - Set ‘Log Output’ to log discarded packets. Otherwise, a dropped packed is not logged.
IPSec Pass-Through - Enables the AirStation’s ability to pass IPSec VPN data.
47
Address Translation
Address Translation - Select Enable or Disable. Address Translation must be enabled for client computers to con­nect to the Internet. Selecting Enable enables the following functions:
IP Masquerade - When the LAN computer connects to the WAN side, the IP address of LAN computer is dynamically translated to become the WAN IP address of the AirStation. Multiple LAN computers can share one WAN IP address to access the Internet.
Page 48
Advanced Settings
IP Address of DMZ - Allows administrator to set the DMZ (De-Militarized Zone) address. Incoming packets containing no recognizable destination port information will be re di rect ed to the DMZ’s IP address.
Display/Delete NAT Table - Allows ad min is tra tor to delete NAT tables.
Add NAT Table
Address
Translation
Setup
dress used by the WAN computer to connect to the local computer. AirStation’s IP Address of WAN should be used unless you have multiple WAN side IP addresses.
Group - Specify a group (up to 16 characters) that the NAT rule belongs. Groups are simply used to visually organize the NAT table for the administrator. It is recommended to name the group after the protocol that is being setup (e.g. Group Name FTP when setting up ad­dress translation for FTP) Click New Group to create new group or select an existing group to add a NAT rule to it.
WAN Side IP Address - Select AirStation’s WAN Side IP Address or Manual IP Ad­dress. For Manual setting, enter the IP ad-
48
Page 49
Advanced Settings
Some network applications (online games or streaming software) require adding Address Transla­tion tables; consult the software’s documentation for port information).
Protocol (WAN):
All - Selects all IP protocols.
ICMP - Network Diagnostic Protocol (1).
Manual - Specify the protocol number (0-65535).
TCP/UDP - Enter port number for TCP or UDP protocols. If both TCP and UDP are required, then separate entries are required.
LAN IP Address - Select Manual IP Address and enter the destination IP address of the LAN computer; or select AirStation’s LAN IP Address.
Protocol (LAN) - Enter the destination port number. If left blank, the packets are transferred to the same port number as the source port number. Typically the destination port should be left the same as the source port.
• Click Add to NAT table. This will add the information to the NAT table. Once you have gone
through this process for every desired translation, you will need to press the Apply button on the top of the screen to start the translating.
49
Page 50
Advanced Settings
Packet
Filter
Setup
Prohibit setup via wireless bridge access point - Prohibits a personal computer connected to another AirStation in a wireless bridge.
Prohibit NBT and Microsoft-DS routing - Prevent unexpected external access via Microsoft network sharing. This prohibits computers on the internet from accessing shared resources on Windows machines. It is recommended to leave this fi lter activated.
Reject the IDENT request - The AirStation sends reject packets if it receives an IDENT request.
50
Packet Filter
Log Output - Select Output to
activate the packet fi lter log.
Packet Filter Information Basic Rule - Click add/delete
basic rules. Place a check mark next to the basic rule to enable:
Prohibit setup from wire- less LAN - Prohibits adminis­tration from a wireless com­puter.
Prohibit setup from wired LAN - Prohibits administration from a wired computer.
Page 51
Advanced Settings
Basic Filter
Setting
Use this fi lter when the commu­nication speed goes down using a network application like E-mail, FTP and WEB.
* If IDENT requests are for­warded to a LAN side client by address translation setting (DMZ or TCP port :113 ), this basic rule is ignored.
51
Page 52
Advanced Settings
IP Filter
setting
• WAN side - packets coming from the WAN side will be fi ltered.
• LAN side - packets from the LAN side will be fi ltered.
Are :
• Ignored - Stop the packet and do not route it.
• Rejected - Return the rejected packet to the point of origin.
• Accepted - Pass the packet through.
Destination IP Address - The IP address to be fi ltered.
Source IP Address - The IP address designated for fi ltering. If all IP addresses must be fi ltered,
leave this box blank.
Warning: If administrator selects packet from LAN is Ignored or Rejected, the ad min is tra tor will
52
type of packets allowed to pass between the WAN and LAN. The maximum number of rules is 32.
Operation - Packets from WAN (or LAN), select ignored, rejected, or accepted. Select the operation to be performed on the packets. Packets from:
IP Filter Settings - Limits the
Page 53
Advanced Settings
no longer have access to the AirStation confi guration screens. This function prohibits setup from a wireless or wired computer. The AirStation can be returned to the factory default settings by holding down the INIT button on the back of the unit for fi ve seconds or until the red DIAG light becomes solid.
Protocol - Mark and select a specifi c protocol. Select from all protocols, ICMP, arbitrary protocol number and TCP/UDP protocol number.
All - Selects all IP protocols.
ICMP - Network Diagnostic Protocol (1).
Manual - Enter protocol number (0-65535).
TCP/UDP Destination Port - Select TCP or UDP, then enter port number.
Priority - Specify the priority an item. The smaller the number, the higher the priority.
Add MAC
Filter
setting
53
MAC Filter - Click Enter MAC
fi lter to enter MAC address.
Source MAC address -The MAC address of the source of the packets that will be fi ltered may be set. Click Add rule when complete.
Page 54
Advanced Settings
Note: If confi guring from a wireless computer, add your MAC address to the list of au tho rized
wireless LAN PCs. The MAC address must be in two-digit groups separated by colons. Example: 00:40:26:00:11:22
Click Apply when settings are complete.
54
Page 55
Advanced Settings
Intrusion Detector
Setup
Notifi cation email address - Enter des ti na tion email address
Sender email address - Enter the email address that will send the email. This is the name that will appear as the sender when the email is read. This email can be made up (e.g. DETECTOR@AIRSTATION
55
Intrusion Detector
The Intrusion Detector watch guards and prevents unauthorized access from the WAN (Internet) This function also records information on unauthorized access attempts
Intrusion Detector - Select Do not use, Use or Use (Apply Packet fi lter setting for Intrusion Detector set­ting).
IP Spoofi ng - Check Block to prevent
IP spoofi ng.
Threshold Value - Enter the number (1-999) of suspect packets before the notifi cation occurs.
Notify by email
Page 56
Sender email server address - Enter the SMTP Server address.
Receiving email server au tho ri za tion - Enter the POP3 Server address, User name and Password. This is only required if your SMTP server requires POP verifi cation before it allows email to be sent. Consult your ISP or mail server support for more information.
Send test - Click Send to test no ti fi ca tion; this will also save and commit the entries.
Pop-up notifi cation - Pop-up window alert of unwanted activity. Client Manager must be installed and running on a client machine to use this feature.
Destination IP address - Enter the IP address to be notifi ed. The LAN computer with this IP address must have Buffalo’s Client Manager software installed and running for the verifi cation to occur. If the machine is off the verifi cation will not be received, and the AirStation will NOT resend information.
Intrusion Detector information - displays log activity detected by the Intrusion Detector service.
56
Page 57
Advanced Settings
UPnP
Setting
UPnP
Select Enable to enable UPnP (Universal Plug and Play). When a computer with UPnP support connects to the AirStation, that computer auto­matically receives confi guration information from the AirStation.
57
Page 58
Advanced Settings
System
Information
with other access points. This is the best place to determine the wireless MAC address.
• LAN
- Displays the AirStation LAN settings
• WAN
- Displays the AirStation WAN settings
• Default Gateway
- Displays the default gateway settings
58
Management
System Information
System information of the AirStation is obtained here.
• Model name
model and fi rmware version
• AirStation Name
AirStation host name
• DHCP Server function
Displays On or Off
• Wireless
wireless LAN settings such
as wireless MAC address and wireless fi rmware. The wireless MAC address is required for setting up WDS
- Displays
- Displays the
- Displays
-
Page 59
Advanced Settings
WAN side IP address auto acquisition - This is the method to acquire the IP address from the
WAN (Internet) side DHCP server. Press Release to release current DHCP WAN information. Press Renew to obtain WAN information from the DHCP server. NOTE: If a manual IP is assigned to the WAN port, this feature is not displayed.
Name and
Password
Setup
Admin Name and Password
AirStation name - When using
multiple AirStations, select a unique name to make it easier to identify each AirStation through the AirStation Manager utility. This utility is seldomly used, thus, the AirStation name value has little value.
Administrator name - “root”, cannot be changed
Administrator password ­Allows the administrator to enter an administrator password to restrict access to the setting screens.
59
Page 60
Advanced Settings
New Password - Enter new password. Enter up to eight alphanumeric characters (case sensi­tive)
Confi rm Password - Reenter the new password for confi rmation
Time Setup
Screen
Time setup
Time setup - Enter the current date and time, and click Set.
NTP - Network Time Protocol. Select Use or Do not use.
Note: If NTP is used, time is set au to mat i cal ly.
NTP server name - Enter the NTP server name
Update Time - Enter the time interval (in hours) for the time check frequency
Time Zone - Select local time zone
Click Apply.
60
Page 61
Advanced Settings
Packet Traf-
fi c Informa-
tion
Packet Traffi c Information
Displays number of packets sent and received for:
Wired WAN
Wired LAN
Wireless LAN
Click Refresh to start update the transfer packet log.
61
Page 62
Advanced Settings
Client
Monitor
Screen
Client Monitor
Displays the wired and wireless clients (computers) that are accessing the AirStation.
MAC address - Shows the client’s MAC address.
IP Address and Medium ­Shows the IP address that is assigned to the client from the DHCP server. The network medium is indicated as wireless or wired depending on how the client is accessing the AirStation.
Note: The Client Monitor only shows clients that have received an IP address from the AirStation’s DHCP server. Clients that have static IP addresses will not appear in the Client Monitor.
62
Page 63
Advanced Settings
PING Test
PING Test
Performs a PING test from the AirStation to a LAN or WAN address.
Enter the target IP address and click OK (e.g. 192.168.11.2
- OR- www.buffalotech.com)
If the test results in an error, then verify you correctly inputted the address and check your connections.
63
Page 64
Advanced Settings
Log
Information
Screen
Log Information
Display log info level - Select Error and/or Notify to spec­ify the types of reports to be logged by the AirStation.
Display log info - Select the specifi c reports to be logged.
Log information - Displays recorded logs.
64
Page 65
Advanced Settings
Syslog
Transmitting
Screen
65
Syslog Transfer
Select Use or Do not use to enable or disable the
AirStation’s ability to transmit information to a Syslog server.
Syslog Server - Enter the IP address of the Syslog server.
Log Information Level
- Select Error and/or Notice to specify the types of reports to be sent to the Syslog server.
Log Information - Select the specifi c reports to be sent to the Syslog server.
Note: work running a Syslog service is required for this.
A server on the net-
Page 66
Advanced Settings
Save/
Restore
Settings
Screen
66
Save/Restore Settings
Save current settings - Click Save to open the fi le saving
dialog and save the current AirStation settings to a fi le. Restored saved settings
- Restores settings from a fi le that has been saved. Click Choose fi le to select the saved fi le and click Restore.
Note: saved by a newer fi rmware than the current one, the AirStation can’t restore the settings.
If the setting fi le is
Page 67
Advanced Settings
Initialization/
Reboot
67
Reboot/Reload Defaults
Click Restart to reboot AirStation
Click Restore to reset the AirStation to default factory settings.
Note: factory settings will erase all settings and passwords previously entered. The AirStation will return to the condition it was in when fi rst purchased.
Resetting to default
Page 68
Advanced Settings
Firmware
Update
Firmware Update
Firmware fi le name
- Click Browse to browse
to the path and fi lename for the new fi rmware. Click Firmware Update to load fi rmware to the AirStation.
Note: Firmware update does not erase current user settings.
Please visit the Buffalo Technology Web Page to download the latest fi rm­wares free of charge.
http://www.buffalotech. com/wireless
68
Page 69
Advanced Settings
AOSS
AOSS
Client Table - Displays the
clients connected via AOSS. The ‘Disconnect’ button disconnects the client from the AOSS router by using MAC Address fi ltering. Once disconnected, the client will still appear in the client list but will appear as disconnected. The client can then be re-enabled by pressing the ‘Re-Enable’ but­ton. A separate table exists for connected Ethernet Convertors. The ‘Refresh’ button updates the tables.
69
Page 70
Advanced Settings
AOSS
Start AOSS Process- Click AOSS icon to begin the AOSS sequence. This starts the AOSS process just like pressing the AOSS button.
Stop AOSS Process- Click AOSS icon to stop AOSS operation. Stopping the AOSS function will turn off AOSS and return the router to non-AOSS function.
70
Manually specify the encryp­tion type - This forces AOSS to
use a specifi ed type of encryp­tion. It is recommended to not change this setting. If the setting is changed then every client that connects must have support for that encryption type.
AOSS Function - Click Enable to allow the AirStation to use AOSS function. Click Disable to shut off the AOSS system. Clicking Disable will disable the
AOSS button on the AirStation.
Page 71
Specifi cations
Additional Information
For more information, please consult:
• The AirStation website at:
http://www.buffalotech.com - for frequently asked questions (FAQ’s) and Software Updates.
WBR2-G54S BASE STATION SPECIFICATIONS
Physical Specifi cations
Dimensions W3 x H6.75 x D6.1in. (76 x 171 x 155mm)
Weight 1 lb. (620g)
Temperature & Humidity
Operation 0˚ to 40˚ C
Maximum humidity 80%
Transit/Storage 0˚ to 40˚ C maximum humidity 80% (no condensation)
Power Characteristics
Transmit Mode 1.1A (Nominal),
Power Supply 3.3 V
71
Page 72
Specifi cations
Regulatory Information
Wireless communication is often subject to local radio regulations. Although AirStation wireless networking products have been designed for operation in the license-free 2.4 GHz band, local radio regulations may impose limitations on the use of wireless com mu ni ca tion equipment.
Networking Characteristics
Compatibility
• IEEE802.11g/b Standard for Wireless LANs (125 High Speed Mode also Available)
• Wi-Fi (Wireless Fidelity) certifi ed by the Wi-Fi Alliance.
Host Operating System
Microsoft Windows® 98SE/ME/NT4.0/2000/XP, Unix, Linux and MacOS
Media Access Protocol
Wired - CSMD/CD (Collision Detection)
Wireless - CSMD/CA (Collision Avoidance) with Acknowledgment (ACK)
Radio Characteristics
RF Frequency Band 2.4 GHz (2400-2483 MHz)
11 selectable channels (3 non-overlapping)
72
Page 73
Modulation Technique Direct Sequence Spread Spectrum
• ODFM for High Transmit Rate
• DQPSK for Standard Transmit Rate
• DBPSK for Low Transmit Rate
Spreading 11-chip Barker Sequence
Nominal Output Power 13.5 dBm
Transmit Rate / Range
High Speed 54 Mbps (125 Mbps in 125 High Speed Mode)
Medium Speed 36 Mbps (96 Mbps in 125 High Speed Mode)
Standard Speed 2 Mbps
Low Speed 1 Mbps
Open Offi ce Environment
160 m (525 ft.)
270 m (885 ft.)
Specifi cations
73
Page 74
Specifi cations
400 m (1300 ft.)
550 m (1750 ft.)
Semi-Open Offi ce Environment
50 m (165 ft.)
70 m (230 ft.)
90 m (300 ft.)
115 m (375 ft.)
Closed Offi ce
25 m (80 ft.)
35 m (115 ft.)
40 m (130 ft.)
50 m (165 ft.)
Receiver Sensitivity -83 dBm -87 dBm -91 dBm -94 dBm (depends on data rate)
Delay Spread (at FER of <1%) 65 ns 225 ns 400 ns 500 ns (depends on data rate)
• The range of wireless devices can be affected by metal surfaces, solid high-density materials and obstacles in the signal path.
74
Page 75
Specifi cations
Table “Radio Characteristics” lists the typical ranges when used indoors:
• In Open Offi ce environments, clients can “see” each other, i.e. there are no physical obstruc­tions between them.
• In Semi-open Offi ce environments, work space is separated by room dividers; client cards are at desktop level.
• In Closed Offi ce environments, workspace is separated by fl oor-to-ceiling brick walls.
Note: measured at Buffalo Technology AirStation laboratories. These values are provided for your guidance but may vary according to the actual radio conditions at the location where the AirStation product is installed.
AirStation IEEE 802.11 Channel Sets
The range of the wireless signal is related to the Transmit Rate of the wireless communication. Communications at a lower Transmit range may travel longer distances.
Center Channel ID FCC
1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457 11 2462 11 default channel
The range values listed in Table “Radio Characteristics” are typical distances as
75
Page 76
Troubleshooting
Common Problems:
• Out of range, client cannot connect to the AirStation.
• Confi guration mismatch, client cannot connect to the AirStation.
• Absence or confl ict with the Client Driver.
• Confl ict of another device with the AirStation hardware.
B.1.1 LED Activity B
Monitoring LED activity helps identify problems.
• Power LED should be GREEN,
• Wireless LED should be GREEN if the line is active. If is it blinking GREEN, wireless communica­tion is active.
• Ethernet LED should be GREEN (100Mbps) or AMBER (10Mbps) while the communication is ac­tive.
DIAG LED Activity
Unplug the power for three seconds. Plug the power back in to monitor the DIAG LEDs during start-up.
If any symptoms match section B.1.1, call the Buffalo Tech Support line 24 hours a day, 7 days a week at 866-752-6210 or email info@buffalotech.com.
76
Page 77
Troubleshooting
Table B.1.1 DIAG LED Activity Table
DIAG LED Display Time Description/Action
Continuous Red Starting RAM Error Red fl ash, 2 times Starting Flash ROM
Error
Red fl ash, 3 times Starting A problem on the wired LAN side
Red fl ash, 4 times Starting A problem on the wireless LAN side
B. 1.2 LEDs Work But Client PC Cannot Connect to Network
If the LEDs indicate that the network is working properly (Power LED is on, Transmit/Receive LED blinks), check the TCP/IP settings of the network.
Changing Client TCP/IP Settings in Windows
Consult the LAN Administrator for TCP/IP settings. To add or change the TCP/IP Settings:
1. On the Windows task bar click Start.
2. Select Settings, then Control Panel.
3. Double-click on the Network icon to view the Network Properties.
4. From the list of installed components, verify the TCP/IP => wireless LAN adapter protocol is installed.
77
Page 78
Troubleshooting
• If the wireless adapter protocol is not yet installed, click the Add button and select the TCP/IP protocol from the list. Refer to Windows Help for more information.
• If the wireless adapter protocol is installed, select the protocol and click the Properties button. Verify the parameters match the settings provided by your LAN Administrator. Make changes if necessary, and click OK.
5. When or if prompted, restart your computer.
B. 1.3 Other Problems
Please refer to www.buffalotech.com for further reference materials.
78
Page 79
Troubleshooting
Troubleshooting WDS (Step-by-Step Instructions)
The most common issue with WDS installations is using the wrong MAC address. The proper MAC Ad­dress for the access points is the ‘Wireless MAC Address’. The best place to document this is under the ‘System Information’ section of the confi guration web page. For proper setup, please continue reading this document.
Problem:
Communication problems with WDS (wireless bridging/repeating).
Cause:
WDS is a very complex bridging system, and it is not part of the 802.11b or 802.11g standard.
Restrictions:
Please verify that the following conditions are met (if just one condition is not satisfi ed, then WDS can­not be used on the wireless network):
1. All wireless access points in the wireless bridge need to be from the same vendor (e.g. all Buffalo access points).
(At time of publication, the Apple Airport Extreme WILL work in WDS with Buffalo G54 access points.)
2. No single access point can communicate with more then six other access points in the wireless bridge.Good Practices:proper location.
79
Page 80
Troubleshooting
The following is a list of good practices with WDS:
1. Start the wireless bridge system with only two access points and then add more access points.
2. Setup all access points in the wireless bridge in close proximity before they are deployed to their
proper location.
3. Only one access point in the wireless bridge should be serving DHCP and routing services unless a routed wired network exists.
Proper Setup:
Please follow the following steps to properly setup WDS.
1. It is recommended that all access points in the bridge are reset to their factory default settings. This is done by holding the INIT button on the rear of the access point down for 5-10 seconds.
2. Login to the fi rst access point in the wireless bridge (this should be the DHCP server enabled ac­cess point if there is not already a routed wired network).
3. Click on the ‘Advanced’ button.
4. The wireless settings page will appear. Select the proper settings for the wireless network. Record all settings on a piece of paper. All settings except for the SSID need to be identical amongst all ac­cess points in the bridge.
(If roaming is desired, then make sure the SSID settings need to be identical as well). Press the ‘Set’
button if any changes are made.
(If the IP address was changed, then reconnecting to the access point for confi guration will require ac-
cessing it via its new IP address in a web browser (e.g. http://NEW_IP_ADDRESS).
80
Page 81
Troubleshooting
5. Click on the ‘LAN port’ link on the left.
6. Check that the ‘LAN side IP address’ values are correct for your network, or leave them as default.
Record the ‘LAN side IP address’. Press the ‘Set’ button if any settings on this page have been set.
7. Click on the ‘Management’ link on the left.
8. The System Information page will appear. In the Wireless section of the table record the MAC ad-
dress (including the :’s). Please make sure the MAC address is recorded from the Wireless section and not the other sections.
9. Logout of the access point by clicking on the ‘Logout’ link on the left. Close the browser window.
10. Login to the second access point in the wireless bridge.
11. Click on the ‘Advanced’ button.
12. The wireless settings page will appear. Select the proper settings for the wireless network. Refer to
the settings recorded from the fi rst access point. All settings except for the SSID need to be identical amongst all access points in the bridge.
(If roaming is desired, then make sure the SSID settings need to be identical as well).
13. Click on the ‘LAN port’ link on the left.
14. Make sure that the ‘LAN side IP address’ ‘IP address’ setting is different then the fi rst access point.
The IP addresses cannot be the same, but they should be on the same network. It is recommended that the IP address of the second access point is one higher then that of the fi rst access point. Thus, if access point one’s address is 1.1.1.1, then access point two’s address should be 1.1.1.2. If there is a ‘DHCP server function’ setting on this page, then make sure to set it to ‘Do not use’ or to ‘Disabled’. Press the ‘Set’ button when fi nished.
81
Page 82
Troubleshooting
15. Click on the ‘Wireless bridge (WDS)’ link on the left.
16. Enable the WDS function and press the ‘Set’ button.
17. Enter the Wireless MAC Address of the fi rst access point (which was recorded on Step 8) into the
fi eld that say ‘MAC Address of AirStation(Wireless)’ (include the :’s). Press the ‘Add’ button.
18. The Wireless MAC address inputted on the step above will appear in the ‘Connected AirStation’ table. Please check that the checkbox under enable is checked, and then press the ‘Enable marked item’ button.
19. At the top of the page, press the ‘Apply’ button.
20. Once the router has rebooted, click on the ‘Management’ tab on the left.
21. The System Information page will appear. In the Wireless section of the table record the MAC ad-
dress (including the :’s). Please make sure the MAC address is recorded from the Wireless section and not the other sections.
22. Logout of the access point by clicking on the ‘Logout’ link on the left. Close the browser window.
23. Login to access point one again.
24. Click on the ‘Advanced’ button.
25. Click on the ‘Wireless bridge (WDS)’ link on the left.
26. Enable the WDS function and press the ‘Set’ button.
27. Enter the Wireless MAC Address of the fi rst access point (which was recorded on Step 21) into the
fi eld that say ‘MAC Address of AirStation(Wireless)’ (include the :’s). Press the ‘Add’ button.
82
Page 83
Troubleshooting
29. At the top of the page, press the ‘Apply’ button.
30. Once the router has rebooted, click on the ‘Management’ tab on the left.
31. Click on the ‘PING test’ link on the left.
32. In the ‘Destination’ fi eld enter the IP address of the second access point and press the ‘OK’ button.
a. If the ‘Result’ section of the table reports information like, “1st: 64 bytes from IP_ADDRESS” then
the WDS bridge is effectively working.
b. If the ‘Result’ section of the table reports “Destination Host Unreachable”, then an error has oc-
curred during the setup.
WDS is a complicated bridging system with a lot of variables. If there are still problems with WDS con-
fi guration on the network, then please call our 24/7 technical support line at 1-866-752-6210.
83
Page 84
Glossary
10BaseT or 100BaseTx: 802.3 based Ether­net network that uses UTP (Unshielded twisted pair) cable and a star topology. 10 is 10 Mbps and 100 is 100 Mbps.
802.1x: The standard for wireless LAN authenti-
cation used between an AP and a client. 802.1x with EAP will initiate key handling.
Ad-Hoc Network: The wireless network based on a peer-to-peer communications session. Also referred to as AdHoc.
Bandwidth: The transmission capacity of a computer or a communication channel, stated in Megabits per second (Mbps).
BSS (Basic Service Set): An 802.11 network­ing framework that includes an Access Point.
Bus Mastering: A system in which the speci­fi ed Input/Output device (e.g. NIC Card) can perform tasks without the intervention of the CPU.
Client: A PC or workstation on a network.
Cross-Over Wiring: A UTP cable that has its
transmit and receive pair crossed to allow com­munications between two devices.
DCE (Data Communications Equipment): Hardware used for communication with a Data Terminal Equipment (DTE) device.
Default Gateway: The IP Address of either the nearest router or server for the LAN.
Default Parameter: Parameter set by the manufacturer.
Destination Address: The address portion of a packet that identifi es the intended recipient station.
DHCP (Dynamic Host Confi guration Pro­tocol): Based on BOOTP, it uses a pool of IP
addresses, which it assigns to each device con­nected to it, and retrieves the address when the device becomes dormant for a period of time.
DNS (Domain Name System): System used to map readable machine names into IP ad­dresses
84
Page 85
Glossary
Driver: Software that interfaces a computer with a specifi c hardware device.
DSSS (Direct Sequence Spread Spectrum): Method of spreading a wireless signal into wide frequency bandwidth.
DTE (Data Terminal Equipment): Device that con10BaseT or 100BaseTx: 802.3 based
Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 10 is 10 Mbps and 100 is 100 Mbps.
Dynamic IP Address: An IP address that is automatically assigned to a client station in a TCP/IP network, typically by a DHCP server.
ESS (Extended Service Set): A set of two or more BSSs that form a single sub-network. SSID is user identifi cation used in the ESS LAN confi guration.
Ethernet: The most widely used architecture for Local Area Networks (LANs). It is a shared­media network architecture. The IEEE 802.3 standard details its functionality.
Ethernet cable: A wire similar to telephone cable that carries signals between Ethernet devices.
File and Print Sharing: A Microsoft application that allows computers on a network to share fi les and printers.
Firmware: Programming inserted into pro­grammable read-only memory, thus becoming a permanent part of a computing device.
Frame: A fi xed block of data, transmitted as a single entity. Also referred to as packet.
Full-Duplex: To transmit on the same channel in both directions simultaneously.
Half-duplex: To transmit on the same channel in both directions, one direction at a time.
Hub: A device which allows connection of com­puters and other devices to form a LAN.
IEEE (Institute of Electrical and Electronics Engineers): The professional organization
which promotes development of electronics technology.
85
Page 86
Glossary
IP (Internet Protocol) Address: A unique 32­binary-digit number that identifi es each sender or receiver of information sent in packets.
Infrastructure: A wireless network or other small network in which the wireless network devices are made a part of the network through the Access Point.
ISP (Internet Service Provider): A company that provides access to the Internet and other related services.
IV (Initialization Vector): The header section of an encrypted message packet.
LAN (Local Area Network): A group of com­puters and peripheral devices connected to share resources.
LED (Light Emitting Diode): The lights on a hardware device representing the activity through the ports.
MAC (Medium Access Control) Address: A unique number that distinguishes network cards.
Mbps (Mega Bits Per Second): A measure­ment of millions of bits per second.
MDI/X (Media Dependent Interface/Cross­over): Port on a network hub or switch that
crosses the incoming transmit lines with the outgoing receive lines.
MHz (MegaHertz): One million cycles per second.
NAT (Network Address Translation): An inter­net standard that enables a LAN to use one set of IP addresses for internal traffi c and a second set for external traffi c.
NIC (Network Interface Card): An expansion card connected to a computer so the computer can be connected to a network.
Packet: A block of data that is transferred as a single unit, also called a frame or a block.
Packet Filtering: Discarding unwanted net­work traffi c based on its originating address or its type.
86
Page 87
Glossary
PCI (Peripheral Component Interconnect): A bus that is connected directly to the CPU.
PCMCIA (Personal Computer Memory Card International Association) Card: Remov-
able module that adds features to a portable computer.
Ping (Packet Internet Groper): An Internet utility used to determine whether a particular IP address is online.
Plug and Play: Hardware that, once in­stalled (“plugged in”), can immediately be used (“played”), as opposed to hardware that requires manual confi guration.
PoE (Power over Ethernet): A mechanism to send DC power to a device using a CAT5 Ethernet cable.
PPPoE (Point-to-Point Protocol over Ether­net): A specifi cation for connecting users on an
Ethernet line to the Internet through a common broadband medium.
Protocol: A standard way of exchanging infor-
mation between computers.
RADIUS (Remote Authentication Dial In User Service): A server that issues authentication key to
clients.
RAM (Random Access Memory): Non-permanent memory.
Repeater Hub: A device that collects, strengthens and transmits information to all connected devices, allowing the network to be extended to accommo­date additional workstations.
RC4: The encryption algorithm that is used in WEP.
RJ-45 connector: An 8-pin connector used be-
tween a twisted pair cable and a data transmission device.
ROM (Read Only Memory): Permanent memory.
Router: Device that can connect individual LANs
and remote sites to a server.
Roaming: The ability to use a wireless device while moving from one access point to another without losing the connection.
87
Page 88
Glossary
Script: A macro or batch fi le containing instruc­tions and used by a computer to perform a task.
Server: Any computer that makes fi les or peripheral devices available to users of the network and has a resident Network OS.
SMTP (Simple Mail Transfer Protocol): The protocol used to defi ne and deliver electronic mail (E-mail) from one location to another.
SNMP (Simple Network Management Proto­col: An application layer protocol that outlines
the formal structure for communication among network devices.
Static IP Address: A permanent IP address is assigned to a node in a TCP/IP network. Also known as global IP.
STP (Shielded Twisted Pair): Twisted Pair cable wrapped in a metal sheath to provide ex­tra protection from external interfering signals.
Subnet Mask: An eight-byte address divided into 4 parts separated by periods.
TCP/IP (Transmission Control Protocol/In­ternet Protocol: Protocol used by computers
when communicating across the Internet or Intranet.
TKIP (Temporal Key Integrity Protocol): An encryption method replacing WEP. TKIP uses random IV and frequent key exchanges.
Topology: The shape of a LAN (Local Area Network) or other communications system.
Twisted Pair: Cable that comprises 2 or more pair of insulated wires twisted together.
UDP (User Datagram Protocol): A com­munication method (protocol) that offers a limited amount of service when messages are exchanged between computers in a network. UDP is used as an alternative to TCP/IP.
Uplink: Link to the next level up in a communi­cation hierarchy.
UTP (Unshielded Twisted Pair) cable: Two or more unshielded wires twisted together to form a cable.
88
Page 89
WAN (Wide Area Network): A networking sys­tem covering a wide geographical area.
WEP (Wired Equivalent Privacy): An encryp­tion method based on 64 or 128-bit algorithm.
Web Browser: A software program that allows viewing of web pages.
Wi-Fi (Wireless Fidelity): An organization that tests and assures interoperability among WLAN devices.
Wire Speed: The maximum speed at which a given packet can be transferred using Ethernet and Fast Ethernet standard specifi cations.
WLAN (Wireless LAN): A LAN topology using wireless devices.
VPN (Virtual Private Network): A security method to connect remote LAN users to a cor­porate LAN system.
Glossary
89
Page 90
FCC / CE Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con­nected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
90
Page 91
FCC / CE Information
IMPORTANT NOTE:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
91
Page 92
FCC / CE Information
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. BUFFALO declared that WBR2-G54S is limited in CH1~11 by specified firmware controlled in USA.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment.
EU Countries intended for use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Norway, The Netherlands, Portugal, Spain, Sweden, Switzerland and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states Iceland,
Liechtenstein, Norway and Switzerland.
EU Countries Not intended for use
None.
Potential restrictive use
France: Only channels 10,11,12, and 13.
92
Page 93
Warranty Information
Buffalo Technology (Melco Inc.) products comes with a two-year limited warranty from the date of purchase. Buffalo Technology (Melco Inc.) warrants to the original purchaser the product; good operat­ing condition for the warranty period. This warranty does not include non-Buffalo Technology (Melco Inc.) installed components. If the Buffalo product malfunctions during the warranty period, Buffalo Technology/(Melco Inc.) will, replace the unit, provided the unit has not been subjected to misuse, abuse, or non-Buffalo Technology/(Melco Inc.) authorized alteration, modifi cations or repair.
All expressed and implied warranties for the Buffalo Technology (Melco Inc) product line including, but not limited to, the warranties of merchantability and fi tness of a particular purpose are limited in duration to the above period.
Under no circumstances shall Buffalo Technology/(Melco Inc.) be liable in any way to the user for damages, including any lost profi ts, lost savings or other incidental or consequential damages arising out of the use of, or inability to use the Buffalo products.
In no event shall Buffalo Technology/(Melco Inc.) liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying software, or its documentation. Buffalo Technology/(Melco Inc.) does not offer refunds for any product.
@ 2003 Buffalo Technology (Melco, Inc.)
93
Page 94
Contact Information
ADDRESS
Buffalo Technology (USA), Inc.
4030 West Braker Lane, Suite 120
Austin, TX 78759-5319
GENERAL INQUIRIES
Monday through Friday
8:30am-5:30pm CST
Direct: 512-794-8533 | Toll-free: 800-456-9799 | Fax: 512-794-8520 | Email: sales@buffalotech. com
TECHNICAL SUPPORT
North American Technical Support by phone is available 24 hours a day, 7 days a week. (USA and Canada).
Toll-free: (866) 752-6210 | Email: info@buffalotech.com
* When operating in High-Speed Mode, this Wi-Fi device achieves an actual throughput of up to 34.1 Mbps, which is the
equivalent throughput of a system following 802.11g protocol and operating at a signaling rate of 125 Mbps.
94
Page 95
4030 W. Braker Ln. Suite 120
Austin, Texas 78759
Tel: 800-456-9799
Fax: 512-794-8606
Technical Support is available 24 hours a day, 7 days a week
(USA / Canada)
Toll-Free: 866-752-6210
email: info@buffalotech.com
©2004, Buffalo Technology (USA), Inc.
95
Loading...