Buffalo BF CTCOC, 444443011 Instruction Manual

User Instruction Manual

Counter Top Convection Oven

These instructions cover the Buffalo Counter Top Convection Oven, SKU 444443178

SKU 444443178

Please read and
keep these
instructions

WARRANTY

1 Year Parts

1 Year Labour

INTRODUCTION.

To ensure you obtain full benets from your new oven:

• Please read this instruction booklet carefully, and follow all instructions.

• If you are unsure of any aspect of the installation, use or performance of your oven,
please contact the after sales number shown on the back page.

SPECIFICATIONS

Model BF CTCOC

SKU Number 444443178
Dimensions Height 395mm

Width 611mm
Depth 611mm

Weight 24kg
Voltage 230V ~50Hz
Power rating 2400W

INSTALLATION

Installation Requirements
It is essential that this appliance is installed correctly. Installation should comply with all

local electrical, and health and safety requirements.

WEEE directive registration no. WEE/DK0059TT
At end of unit life, dispose of appliance and any replacement parts in a safe
manner, via a licenced waste handler. Units are designed to be dismantled
easily and recycling of all material is encouraged whenever practicable.

Before Connection to Power Supply:

Remove all packaging.
Check the oven and parts for damage. Report any damage immediately to the carrier or

supplier.

Remove any protective plastic coating from the outer panels.
Check the following parts have been supplied with your oven:
1 x Oven shelf
Check the available power supply corresponds to that shown on the oven rating label.

Location:

This oven is for indoor use only.
Do not install the oven in a cabinet, it is for counter top use only. Allow at least 200mm
clearance above the oven (Please note this oven cannot be stacked).
The oven is only to be installed in locations where its use and maintenance is restricted to

trained personnel.

The mains lead should reach from the mains socket without straining the connections.
Do not let the mains lead hang over the edge of the table or counter, and keep it away
from any hot surfaces.
Do not let the mains lead run across an open space.
Do not place the oven where the mains lead could fall into a sink.
Do not place the oven near a hot gas or electric burner.
Ensure the oven is level both from side to side and front to back, to ensure even cooking.
There are adjustable feet on each corner, tighten the locknuts after adjustment.

The oven should be positioned such that it can be loaded and unloaded easily, and the
controls can be operated conveniently.

Important:
DO NOT OBSTRUCT THE VENTILATION SLOTS IN THE BASE /SIDE AND REAR OF
THE OVEN.

Electrical Connection:

Fitting a plug
The mains lead of this oven will already be tted with a BS1363 13A plug. If the fuse has to
be replaced, use a 13 amp fuse complying with BS 1362.
If the plug is not suitable for your socket then the plug must be cut off and disposed of safely.
An appropriate plug should be tted as follows:
IMPORTANT: The wires in the mains lead are coloured in accordance with the following
code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
The wire which is coloured green and yellow must be connected to the terminal in the plug
which is marked with the letter E or the earth symbol or coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the

letter N or coloured black or blue.

The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red or brown.
Make sure that the connections are tight and that there are no loose strands of wire and no
insulation trapped under the terminals. Tighten the clamp in the plug making sure that it grips
the outer covering of the cord. If tting a BS 1363 13A fused plug then t a 13A fuse. Tighten
the plug cover securely. If you are in any doubt, consult a qualied electrician.

IMPORTANT: if the supply cord is damaged, it must be replaced by the manufacturer,
service agent or similar qualied person in order to avoid a hazard. The supply cord may
become warm when the appliance is in use.

WARNING - THIS APPLIANCE MUST BE EARTHED

In addition to the earth within the mains plug, connect the equipotential bonding
terminal on the rear panel.

Electrical connection: 230V ~ 50Hz, 10.5A, 2400W

Before Use:

Operate the oven for approximately 30 minutes at the highest temperature, to remove any
fumes or odour which may be emitted - this is due to oil used during manufacture, or from
the oven insulation, but is not harmful.

611

390

611