Buderus 600 - 19S, 600 - 24S, 600 - 24C Installation And Maintenance Instructions Manual

Download

Page 1

7209 6700 - 02/2006 GB (EN) For the installer

Please read thoroughly

Installation and maintenance instructions

Gas wall hung Boiler condensing 600 - 11S / 19S / 24S / 24C

122

Page 2

2 Installation and servicing instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Subject to technical modifications!

Constant development efforts may result in changes to illustrations, functional steps and technical data.

Updating the documentation

If you have suggestions for improvement or have found discrepancies, please do not hesitate to contact us.

The boiler meets the basic requirements of the appropriate standards and directives.

Conformity has been substantiated by the proper documents which - together with the declaration of conformity - are filed with the manufacturer.

Page 3

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 3

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Contents

1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.1 Dimensions, connections and assembly . . . . . . . . 6

1.2 Boiler assembly - exploded view . . . . . . . . . . . . . . 7

1.3 Flue Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.4 Items supplied with unit . . . . . . . . . . . . . . . . . . . . 11

1.5 Hanging the boiler . . . . . . . . . . . . . . . . . . . . . . . . 11

1.6 Water circulation system . . . . . . . . . . . . . . . . . . . 12

1.7 Pipe connections . . . . . . . . . . . . . . . . . . . . . . . . . 12

1.8 Flue installation . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.9 Electrical connections. . . . . . . . . . . . . . . . . . . . . . 17

1.10 Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2 Initial start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.1 Preparing the boiler for operation. . . . . . . . . . . . . 22

3 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.1 Preparing the heating boiler for inspection . . . . . . 30

4 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.1 Clean the heat exchanger, burner and condensate

trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.2 Flushing out the hot-water heat exchanger . . . . . 35

5 Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.1 Operating codes . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.2 Fault codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.3 Checking and replacing parts. . . . . . . . . . . . . . . . 45

6 Changing to another type of gas . . . . . . . . . . . 59

7 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

7.1 Technical specifications . . . . . . . . . . . . . . . . . . . . 62

7.2 Short list of spare parts . . . . . . . . . . . . . . . . . . . . 64

8 Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

8.1 Start-up report . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

8.2 Inspection and maintenance reports . . . . . . . . . . 66

G. C. Aplliance No. :

Buderus 600 - 11S 41-110-16 Buderus 600 - 19S 41-110-17 Buderus 600 - 24S 41-110-18 Buderus 600 - 24C 47-110-01

Preface

These installation and servicing instructions apply to: Buderus wall-mounted condensing gas boilers 600 - 11S / 19S / 24S / 24C.

Model C13, C33, C

Type GB II

2H3P

20 mbar, 37 mbar

In this document: NG = 2-G20-20 mbar

LPG = 3P-G31-37 mbar

Power rating: 230 VAC, 50 Hz, IPX4D

Fuse rating: 1.25 Ampere slow blow

Important general instructions for use

Only use the boiler in accordance with its designated use and the installation and servicing instructions. Servicing and repair must be carried out by CORGI registered installer. Only use the boiler in combinations and with the accessories and spare parts indicated in the installation and servicing instructions. Other combinations, accessories and consumables may only be used if they are expressly provided for the designated use and if system performance and safety are not affected in any way.

The boiler is suitable for connection to fully pumped, sealed water systems ONLY. Adequate arrangements for completely draining the system by provision of draining valves must be provided in the installation pipework.

Pipework from the boiler is routed downwards as standard, but may be routed upwards behind the boiler using the distance frame (supplied in a separate kit).

Subject to technical modifications.

As a result of our policy of constant development, there may be small differences between illustrations, functional steps and technical data.

BENCHMARK' Log Book

All Buderus gas fired boilers now include an installation, commissioning and service record log book. The details of the log book will be required in the event of any warranty work being requested. Please complete the appropriate sections on completion of the installation and commissioning.

REMEMBER: Please hand the log book back to the user.

Page 4

4 Installation and maintenance instructions wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Regulations and directives

It is law that all gas appliances are installed and serviced by a CORGI registered installer in accordance with the regulations. Failure to install appliances correctly could lead to prosecution. It is in your own interest, and that of safety, to ensure the law is complied with.

The installation must also be in accordance with the latest I.E.E (BS.7671) Wiring Regulations, water regulations, the building regulations and the Building Standards (Scotland) and any relevant requirements of the local authority.

It is a requirement and in your own interest, and that of safety that this boiler must be installed by a CORGI registered installer, in accordance with the relevant requirements of the current Gas Safety (Installation and Use) Regulations, The Building Regulations, current I.E.E. Wiring Regulations and the relevant British Standard Codes of Practise.

Detailed recommendations are contained in the following British Standard Codes of Practice:

BS. 5440:1 Flues (for gas appliances of rated input not

exceeding 70 kW).

BS. 5440:2 Ventilation (for gas appliances of rated input not

exceeding 70 kW).

BS. 5449 Forced circulation hot water systems. BS. 5546 Installation of gas hot water supplies for domestic

purposes (2nd. family Gases).

BS. 6798 Installation of gas fired hot water boilers of rated

input not exceeding 60 kW.

BS. 6891 Low pressure installation pipes.

IGE/UP/1b Tightness testing and purging domestic sized gas

installations.

Health and & Safety Document No. 635.

The Electricity at Work Regulations, 1989.

The manufacturer's notes must not be taken, in any way, as overriding statutory obligations.

The design and construction of the Buderus wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C conforms to the basic specifications listed in the European directive governing gas-fired appliances 90/396/EEC, and with respect to EN 625, EN 483 and EN 677.

Timber Framed Buildings

If the boiler is to be fitted in a timber framed building it should be fitted in accordance with the Institute of Gas Engineering document IGE/UP/7:1998.

Bathroom Installations

This appliance is rated IPX4D.

The boiler may be installed in any room or internal space, although particular attention is drawn to the requirements of the current IEE (BS.7671) Wiring Regulations and, in Scotland, the electrical provisions of the building regulations applicable in Scotland, with respect to the installation of the boiler in a room or internal space containing a bath or shower.

If the appliance is to be installed in a room containing a bath or shower then, providing water jets are not going to be used for cleaning purposes (as in communal baths/showers), the appliance can be installed in Zone 3, as detailed in BS.7671.

Compartment Installations

A compartment used to enclose the boiler should be designed and constructed especially for this purpose.

An existing cupboard or compartment may be used, provided that it is modified for the purpose.

In both cases, details of essential features of cupboard/ compartment design, including airing cupboard installation, are to conform to the following: BS 6798 (No cupboard ventilation is required - see 'Air Supply' for details).

It is not necessary to have a purpose-provided air vent in the room or internal space in which the boiler is installed. Neither is it necessary to ventilate a cupboard or compartment in which the boiler is installed, due to the low surface temperatures of the boiler casing during operation; therefore the requirements of BS 6798, Clause 12, and BS 5440:2 may be disregarded.

The position selected for installation MUST allow adequate space for servicing in front of the boiler.

For the minimum clearances required for safety and subsequent service, see the wall mounting template. In addition, sufficient space may be required to allow lifting access to the wall mounting plate.

Wall-mounted condensing gas boilers must only be operated with the combustion air/flue gas systems especially devised and authorised for this type of boiler.

NOTE

Observe the corresponding technical rules and the building supervisory and statutory regulations when installing and operating the system.

WARNING!

Keep the burner-control unit housing CLOSED when working on water-bearing components.

NOTE

It is mandatory to clean and service the system once a year. This includes an inspection of the entire system to see if it is in full working order. Defects and faults must be eliminated immediately.

NOTE

When instructions aren’t followed, warranty expires.

Page 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 5

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Observe the relevant standards, regulations and legislation of the country of final use.

Safe handling of substances

Care should be taken when handling the boiler's insulation, which can cause irritation to the skin.

No asbestos, mercury or CFCs are included in any part of the boiler and its manufacture.

CAUTION

Use this device for its intended purpose only.

DANGER! Notes relating to the heating system water.

Thoroughly flush the system before it is filled with water. Use only untreated water or water treatment product such as Sentinel X100 to fill and top up the system.

When using water treatment, only products suitable for use with Buderus heat exchangers are permitted (e.g. Sentinel X100). Your warranty is at risk if an incorrect water treatment product is used in conjunction with this appliance. For more information, contact Buderus Product Support Department.

It is most important that the correct concentration of the water treatment product is maintained in accordance with the manufacturer's instructions.

If the boiler is used in an existing system any unsuitable additives MUST be removed by thorough cleaning. BS.7593:1992 details the steps necessary to clean a domestic central heating system.

In hard water areas, treatment to prevent lime scale may be necessary - however, the use of artificially softened water is NOT permitted.

Under no circumstances should the boiler be fired before the system has been thoroughly flushed.

Do not use water softened in a salt bedding exchanger.

Do not use inhibitors, anti-freeze or other additives.

The expansion vessel must be of sufficient size.

When oxygen-permeable pipes are used (e. g. for floor heating systems) the system must be separated by means of heat exchangers. Unsuitable heating water promotes sludge formation and corrosion. This may cause malfunctions and damage in the heat exchanger.

NOTE: Notes relating to domestic hot water.

z The domestic hot water service must be in

accordance with BS 5546 and BS 6700.

z The boilers are suitable for connection to

most types of washing machine and dishwasher appliances.

z When connecting to suitable showers,

ensure that:

a. The cold inlet to the boiler is fitted with

an approved anti-vacuum or syphon non-return valve.

b. Hot and cold water supplies to the

shower are of equal pressure.

z Where the water hardness exceeds

150 mg/litre, it is recommended that a proprietary scale reducing device is fitted into the boiler cold supply with the requirements of the local water company.

CAUTION

Provision must be made to accommodate the expansion of DHW contained within the appliance, if a non-return valve is fitted to the DHW inlet, as detailed in BS. 67989: §5.4.3.

Page 6

Installation1

6 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

1 Installation

1.1 Dimensions, connections and assembly

480 mm (19")

240 mm (9½")

Ø100 (4")

Ø60 (2 ")

370 mm (14½")

185 mm (7¼")

105 mm (4 ")

DHW Hot, DHW Cold / 35 mm (1¼")

CH Flow, CH return, GAS / 50 mm (2")

12.5 mm (½")

950 mm (37½")

850 mm (33½")

1.5 mm ( ")

845.5 mm (33 ")

840 mm (33")

GAS

CWDO

(2½")65(2½")65(2½")

(2½")

65 (2½")

13 mm (½")

CH Flow

DHW Hot

DHW Cold

CH Return

PRV

CH Flow = CH flow Ø22 mm compression fitting GAS = Gas connection for 24C: Ø22 mm compression fitting

for 11S/19S/24S: R¾" CH Return = CH return Ø22 mm compression fitting CWDO = Condensate drain G1" OUTSIDE DHW Hot = DHW warm out Ø15 mm compression fitting DHW Cold = DHW cold in Ø15 mm compression fitting PRV = Pressure relief valve R¾" (¾" - ½"-adapter supplied with boiler)

NOTE

See wall-mounting template for the necessary clearances.

Page 7

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 7

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

1.2 Boiler assembly - exploded view

Single unit (11S / 19S / 24S)

Legend

1. Flow connection piece

2. Automated air vent

3. Hairpin heat exchanger

4. Flow sensor

5. Clip

6. Flow pipe

7. Clip flow pipe

8. Back part heat exchanger

9. Seal heat exchanger

10. Sealing ring burner

11. Burner

12. Heat exchanger

13. Front panel heat exchanger

14. Sight glass

15. Fastener

16. Ventilation cover

17. Casing

18. Condensate trap

19. Syphon cap with seal

20. Drain pipe condens. trap

21. Syphon

22. Sealing ring

23. Flue gas sensor

24. Sealing ring

25. Flue gas pipe

26. Flue gas pipe seal

27. Condensate collector

28. Lipring

29. Combustion divider

30. Insulation divider

31. Fan

32. Gas/air supply pipe

33. Fan seal

34. Venturi

35. Gas valve

36. Rectifier

37. Suction pipe

38. Gas pipe

39. Concentric adapter

40. Lip ring

41. Adapter clip

42. Bracket

43. Cable duct

4 0

6 0

8 01

0 0

12 0

2 0

2 3

b a r

44. Ventilation cover seal

45. Pipe duct

46. Sealing ring

47. Cable harness

48. UBA

49. Power switch

50. Temp-pressure gauge

51. UBA panel

52. 230V cable

53. O-ring

54. O-ring

55. Return pump connection pipe

56. Pump

57. Expansion vessel

58. Expansion vessel pipe

59. Manifold assembly

60. Pressure relief valve

61. Spring set

62. Connection house by-pass

63. Clip by-pass

64. Connection house three-way valve

65. Spring set

66. Connection housing pump

67. Connection housing

68. Clip

69. By-pass pipe

82. Hot surface ignitor

83. Ionisation electrode

Page 8

Installation1

8 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Combi unit (24C)

Legend

1. Flow connection piece

2. Automated air vent

3. Hairpin heat exchanger

4. Flow sensor

5. Clip

6. Flow pipe

7. Clip flow pipe

8. Back part heat exchanger

9. Seal heat exchanger

10. Sealing ring burner

11. Burner

12. Heat exchanger

13. Front panel heat exchanger

14. Sight glass

15. Fastener

16. Ventilation cover

17. Casing

18. Condensate trap

19. Syphon cap with seal

20. Drain pipe condens. trap

21. Syphon

22. Sealing ring

23. Flue gas sensor

24. Sealing ring

25. Flue gas pipe

26. Flue gas pipe seal

27. Condensate collector

28. Lipring

29. Combustion divider

30. Insulation divider

31. Fan

32. Gas/air supply pipe

33. Fan seal

34. Venturi

35. Gas valve

36. Rectifier

37. Suction pipe

38. Gas pipe

39. Concentric adapter

40. Lip ring

41. Adapter clip

42. Bracket

43. Cable duct

44. Ventilation cover seal

45. Pipe duct

46. Sealing ring

47. Cable harness

48. UBA

49. Power switch

50. Temp-pressure gauge

8 01

0 0

1 2 0

2 0

2 3

b a r

4243

51. UBA panel

52. 230V cable

53. O-ring

54. O-ring

55. Return pump connection pipe

56. Pump

57. Expansion vessel

58. Expansion vessel pipe

59. Manifold assembly

60. Pressure relief valve

61. Spring set

62. Connection house by-pass

63. Clip by-pass

64. Connection house three-way valve

65. Spring set

66. Connection housing pump

67. Connection housing

68. Clip

69. By-pass pipe

70. DHW pipe (hot)

71. Clip

72. DHW supply pipe

73. Hot water sensor

74. Boiler sensor

75. Insulation hot water tank

76. DHW pipe (cold)

77. Flow regulator

78. Three-way valve body

79. Three-way valve cartridge

80. Three-way valve cover

81. Three-way valve head

82. Hot surface ignitor

83. Ionisation electrode

84. Hot water tank

Page 9

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 9

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

1.3 Flue Installation

1.3.1 Siting the flue terminal

The flue must be installed in accordance with the recommendations of BS. 5440-1:2000.

Pluming will occur at the terminal so terminal positions where this could cause a nuisance should be avoided.

The air supply and the flue gas exhaust must meet the applicable general regulations. Please consult the instructions provided with the flue terminal kits prior to installation.

The boiler MUST be installed so that the terminal is exposed to external air.

It is important that the position of the terminal allows the free passage of air at all times.

Minimum acceptable spacing from the terminal to obstructions and ventilation openings are specified in table 1.

If the terminal is fitted within 1000 mm of a plastic or painted gutter or within 500 mm of painted eaves, an aluminium shield of at least 1000 mm long should be fitted to the underside of the gutter or painted surface.

If the lowest part of the terminal is less than 2 metres above the level of the ground, balcony, flat roof or place to which any person has access, the terminal must be protected by a guard. Protective guards are available from Quinnell Barrett and Quinnell, Old Kent Road, London.

Ensure that the guard is fitted centrally.

The flue assembly shall be so placed or shielded as to prevent ignition or damage to any part of the building.

The air inlet/products outlet duct and the terminal of the boiler MUST NOT be closer than 25 mm (1'') to combustible material. Detailed recommendations on the protection of combustible material are given in BS. 5440- 1:2000.

If this could occur the appliance MUST be turned off (with the owners permission), and labelled as unsafe until corrective action can be taken.

Fig. 1 Flue terminal position

B,C

H, I

under carport

Terminal Position

Minimum

Spacing

A. Directly below or alongside an opening

window, air vent or other ventilation opening

300 mm (12")

B. Below guttering, drain pipes or soil pipes

75 mm (3")

C. Below eaves

200 mm (8")

D. Below balconies or a car port roof

200 mm (8")

E. From vertical drain pipes or soil pipes

150 mm (6")

F. From internal or external corners

300 mm (12")

G. Above adjacent ground, roof or balcony level

300 mm (12")

H. From a surface facing the terminal

600 mm (24")

I. From a terminal facing a terminal

1200 mm (48")

J. From an opening in a car port (e.g. door or

window) into dwelling

1200 mm (48")

K. Vertically from a terminal on the same wall

1500 mm (60")

L. Horizontally from a terminal on the wall

300 mm (12")

M. Adjacent to opening

300 mm (12")

Table 1 Balanced flue terminal position

NOTE

It is absolutely essential to ensure, in practice, that products of combustion discharging from the terminal cannot re-enter the building or any other adjacent building through ventilators, windows, doors, other sources of natural air infiltration, or forced ventilation/airconditioning.

Page 10

Installation1

10 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

1.3.2 Air supply and flue gas exhaust in a closed installation

A ventilation cover is integrated into the 600 Series condensing gas boilers. This cover houses a number of components, such as the burner and the heat exchanger. Since this ventilation cover is part of the air supply system, it is vital that it is always installed correctly.

To ensure optimal operation, the 600 Series appliances must be connected to a Buderus wall-mounted or roof-mounted flue terminal. These terminals have been developed specifically for the 600 Series condensing gas boilers and have been comprehensively tested. The Buderus wall and roof-mounted flue terminal kits ensure trouble-free operation.

The following items for the flue (see fig. 2) are included in the delivery of the boiler:

– pos. 1: 1 Concentric bend 60/100;

– pos. 2: 1 Horizontal flue terminal 60/100;

– pos. 3: 1 Flue finishing kit.

1.3.3 Maximum Flue length

The maximum pipe length of the air supply and flue gas exhaust pipes for the 600 Series condensing gas boilers (see table 2) is determined by the total pressure loss of all components in the flue gas exhaust / air supply system.

Take the flue conduit clearances into account when planning the layout of the place of installation (see subsection 1.3.1: "Siting the flue terminal" on page 9).

Maximum wall thickness without extensions is 550 mm. Maintain a minimum side wall clearance of 50 mm (see fig. 3).

1.3.4 Additional flue parts

Additional flue parts (see table 3) can be ordered from your supplier.

Fig. 2 Horizontal flue pack

Fig. 3 Side flue and rear flue installation

550 mm

50 mm

Flow pressure available for use [Pa]

600 Series

11 S 19 S 24 S 24 C

35 60 100 10

Boiler

Maximum

pipe length

For every 90° bend the

maximum pipe length has

to be reduced by

600 Series L = 7.5 m 1.2 m

Table 2 Pipe length

Flue parts Order No.

Concentric pipe, 500 mm long, adjustable NE 83703

Concentric pipe, 1000 mm long, not adjustable NE 83704

Concentric bend 90° NE 83705

Concentric bend 45° NE 83706

Table 3 Additional flue parts

Page 11

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 11

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

1.4 Items supplied with unit

z Check the contents against the packing list to ensure that

nothing is missing.

Requirements to be met by the place of installation

1.5 Hanging the boiler

z Attach the manifold assembly to the wall (see fig. 5,

item 1).

z Attach the pipes.

z Attach the wall bracket.

z When using a stand-off frame, refer to the manual of the

stand-off frame for the correct mounting instructions.

z Loosen the retaining screw on the bottom of the

condensing gas boiler.

z Detach the outer casing of the condensing gas boiler.

z Hang the condensing gas boiler onto the wall bracket

(fig. 5).

Fig. 4 Items supplied with unit

Key to fig. 4:

1: Wall-mounted condensing gas boiler

2: Wall bracket

3: Technical documents

4: Manifold assembly

5: Filling loop

6: Plastic bag containing the following accessories:

4 x wall fixing-screws 4 x wall plugs 4 x washers Seals (1 x 1“, 2 x ¾“, 2 x ½“) Square wrench Initial start-up sticker Second identification plate Safety valve nipple (from ¾“ to ½“)

NOTE

Observe all statutory building regulations applying to the place of installation.

DANGER!

Inflammable materials or liquids must not be stored or used near wall-mounted condensing gas boilers. The site of installation must be frost-protected.

CAUTION

DO NOT remove the polystyrene foam bottom slab protecting the connection nozzles. During installation work, cover the wallmounted condensing gas boiler and the flue gas adapter to prevent site dirt from entering, e. g. using aluminium foil.

Fig. 5 Installation

NOTE

If the boiler isn't connected to the pipework immediately, place caps on the pipe connections.

Page 12

Installation1

12 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

1.6 Water circulation system

The central heating system should be in accordance with BS.6798 and, in addition, for smallbore and microbore systems, BS.5449.

1.7 Pipe connections

Pipework from the boiler is routed downwards as standard, but may be routed upwards behind the boiler using the stand-off frame (supplied in a separate kit).

z Connect pipes as shown in fig. 6. Ensure that all pipework

is routed so as to minimise any strain on the boiler fittings.

1.7.1 Gas Supply

The gas installation must be installed in accordance with BS6891.

The complete installation MUST be tested for gas tightness and purged as described in IGE/UP/1b.

1.7.2 Gas connection

z Connect to gas supply according to relevant standards,

installing a screw-threaded gas shutoff valve (accessory) to the gas supply system.

1.7.3 Hot-water temperature for 600 - 24C

z Fit a non-shutting diaphragm safety valve (max. 8 bar)

upstream of the cold-water inlet. This is not required if the building is equipped with a pressure regulator configured to guarantee that the maximum supply pressure of 10 bar cannot be exceeded.

z Connect pipes free of tension (fig. 6).

Fig. 6 Pipe connections

Key to fig. 6:

1: CH flow

2: DHW warm out (combi only)

3: Gas

4: DHW cold in (combi only)

5: CH return

6: Condensate trap

123

CAUTION!

Pipework from the meter to the boiler MUST be of adequate size.

CAUTION

DO NOT use galvanised pipes or fittings. The hot water heat exchanger is made of copper and is liable to suffer the effects of electrolytic corrosion.

NOTE

When using plastic pipes, observe the supplier’s instructions  especially those referring to recommended jointing techniques and the notes relating to the heating system water on page 5.

Page 13

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 13

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

1.7.4 Condensate drain

A condensate drain is integrated in the boiler. The drain outlet is a standard G1" outside connection. This drain needs to be connected to a drainage point. All pipework and fittings in the condensate drainage system MUST be made of plastic - no other materials may be used. The routing of the drain must be made to allow a minimum fall of 1 in 20 away from the boiler, throughout its length. Excessive external pipe runs should be avoided in order to prevent possible freezing. Any external pipework should be a minimum of 32 mm internal diameter.

Ensure that the condensate trap is filled with water.

1.7.5 Condensate removal

Positioning and termination of the condensate drain pipe

The condensate pipe should be run and terminate internally to the house soil and vent stack or waste pipe. Alternatively, the condensate can be discharged into the rainwater system, or into a purpose-made soak away (condensate absorption point). All connecting drainage pipework should have a fall of at least

2.5° to the horizontal, or approximately 50 mm per metre of pipe run. If the drainage pipe has to be run externally, it is recommended that the pipe be insulated to protect against frost. It should be noted that the connection of a condensate pipe to a drain may be subject to local building controls.

Material for condensate

The condensate drainage pipe should be run in a standard drain pipe material, e.g. PVC (polyvinyl chloride), PVC-U (unplasticized polyvinyl chloride), BS (acrylonitrilebutadienestyrene), PP (polypropylene polyprolene) or PVC-C (cross-linked polyvinyl chloride).

WARNING!

Any external run must be insulated.

Page 14

Installation1

14 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Any internal pipework should be of a diameter to match the requirements of the condensate exit pipe on the appliance. A 32 mm (1¼") waste pipe solvent weld fitting can be used, fitted externally over the condensate exit pipe on the appliance. All external pipework should be kept to a minimum to avoid freezing and should have a diameter of not less than 22 mm.

Internal termination to internal stack

The condensate drainage pipe should have a minimum diameter of 1" with no length restriction. It should incorporate a trap with a 75 mm condensate seal and be connected to the stack at a point at least 450 mm above the invert of the stack. The trap built into the boiler will provide this 75 mm condensate seal. For all internal and external stack connections a second trap is required to prevent any odours emanating from the condensate air break at the boiler (see fig. 7).

External termination via internal branch (e.g. sink waste)

The condensate drainage pipe should have a minimum diameter of 1" with no length restriction and should incorporate a trap with a 75 mm seal. The connection should preferably be made downstream of the sink waste trap. If the connection is only possible upstream, then the air break is needed between the two traps. This is normally provided by the sink waste pipe (see fig. 8 and fig. 9).

Fig. 7 Internal termination of condensate drainage pipe to

internal stack

No length restriction

Ø22 mm min.

75 mm min. trap

internal soil and vent stack

invert

Boiler

450 mm min.

Fig. 8 External termination of condensate drainage pipe

via internal discharge branch (e.g. sink waste) and condensate syphon

75 mm min. trap

No length restriction

Ø22 mm min.

Open end of pipe direct into gully, below ground but above water level

Boiler

Sink

Fig. 9 External termination of condensate drainage pipe

via internal discharge branch (e.g. sink waste – proprietary fitting) and condensate syphon

No length restriction

Boiler

Open end of pipe direct into gully, below ground but above water level

75 mm min. trap

Ø22 mm min.

Sink

Page 15

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 15

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Condensate absorption point

The condensate drainage pipe should have a minimum diameter of 1" and the external pipe length should not be more than 3 m. The condensate absorption point should be sited in a convenient position as close as possible to the boiler but not in the vicinity of other services. See fig. 10 for information.

1.8 Flue installation

The only flue systems that may be used are those supplied by Buderus. The flue system must be installed in accordance with the requirements of BS5440:1. 2000.

Standard 100 mm flue systems

The standard concentric flue system provides for a max. horizontal straight length of upto 7.5 m (see subsection 1.3.3). Full instructions for fitting this flue are in subsection 1.8.2: "Installation of the horizontal flue" on page 16.

1.8.1 Connecting the vertical flue gas duct

z Fit the vertical flue gas duct (fig. 11) onto the appliance flue

connector.

z For remaining installation of the vertical flue assembly,

refer to the relevant installation instructions.

Fig. 10 External termination of condensate drainage pipe to

absorption point

Ø100 mm min. plastic tube

bottom of tube sealed

limestone cladding

hole depth 400 mm min.

300 mm min.

25 mm min.

Ground (either/or)

Two rows of three 12 mm holes at 25 mm centres 50 mm from bottom of tube and facing away from house

1000 mm min.

Ø22 mm min.

External length of pipe 3m max.

NOTE

When discharging condensate to an outside drain caution must be taken to ensure blockage cannot occur during freezing conditions. If this is likely to occur, the use of a syphon trap is recommended.

Fig. 11 Vertical flue connection

Flue gas testing point

IMPORTANT

Any horizontal flue system fitted to a condensing boiler must be incline towards the appliance at an angle of 3% (30 mm per metre length) to prevent condensate dripping from the flue terminal. This means that the clearance above the appliance must be increased to match the duct length. See figure on page 6.

Fig. 12 Elbow with flue gas testing point

Flue gas testing point

NOTE

When using a stand-off frame, don’t forget to take its measurements into account when designing a flue system.

Page 16

Installation1

16 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

1.8.2 Installation of the horizontal flue

The standard 100 mm diameter horizontal flue system is suitable for lengths upto 560 mm (see fig. 13). For longer flue runs upto 7.5 m, extension air/flue ducts are available (see page 10, table 3).

1.8.3 Flue duct preparation and assembly

z Measure the flue length L. Refer to figures 14 and 15.

z Mark of the lengths shown onto the ducts and cut the

length. The cuts must be square and free from burrs. Terminal assembly outer (air) duct - L-70 mm, inner (flue) duct - L-50 mm. The measurement is made from the ridge at the terminal indicating the outer face of the wall. Refer to figure 16. Extension air duct - L-70 mm, flue duct - L-50 mm. The measurement is from the formed end.

z Assemble flue system completely. Push the ducts fully

together. The slope of the terminal outlet must be face downwards. The assembly will be made easier if a solvent free grease is lightly applied to the male end of the ducts.

z Push the assembly through the wall and slide the turret

onto the flue connector. Refer to figure 12.

z Ensure that the turret is fully entered into the socket on the

boiler. From the outside fix the flue finishing kit to the terminal and, after ensuring the duct is properly inclined towards the boiler, fix the finishing kit to the wall. If the terminal is within 2 m of the ground where there is access then an approved terminal guard must be fitted. The guard must give a clearance of at least 50 mm around the terminal and be fixed with corrosion resistant screws.

Fig. 13 Standard flue

Flue Turret

No Clamp

Maximum 560 mm

Terminal assembly

Outer Wall

NOTE

Use the wall-mounting template to help you mark the position of the side flue opening

Fig. 14 Flue length - rear

185

NOTE

The flue must be inclined to the boiler.

Fig. 15 Flue length - side

NOTE

An inner wall sealing plate is provided which should be fitted to the ducts before assembly.

Fig. 16 Flue terminal position

Outer Wall Face

Flue Finishing Kit

Flue Terminal

Raised Ring locating the terminal relative to the outside wall face

Page 17

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 17

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

1.9 Electrical connections

1.9.1 Mains connection

A mains supply of 230 V - 50Hz is required.

External controls are suitable for volt free or 230 V installation.

Wiring to the boiler MUST be in accordance with the current I.E.E. (BS.7671) Wiring Regulations and any local regulations.

Wiring should be a 3 core PVC insulated cable, not less than

0.75 mm

(24 x 0.2 mm), and to BS.6500 Table 16.

Connection must be made in a way that allows complete isolation of the electrical supply such as a double pole switch having 3 mm (1/8'') contact separation in both poles, or a plug and socket, serving only the boiler and system controls. This boiler is equipped with a double pole switch see fig. 17, item 1. The means of isolation must be accessible to the user after installation.

The electrical connection to the mains supply should be readily accessible and adjacent to the boiler.

If the supply cord is damaged, it must be replaced by a registered Corgi installer to avoid a hazard.

The electrical supply for both the boiler and the system must be taken from the same sparred fused spur outlet.

Fig. 17 UBA

Page 18

Installation1

18 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

1.10 Wiring Diagram

24 VAC

0 VAC

max. 6 VA

hot surface

ignitor

remove bridge when

carrying out connection

Loop is non-conducting

(remove when connecting)

1234

123

Burner-control unit (UBA)

1 2 3 4 5 6 7 8 91011121314151617181920 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

20-pin connection strip 18-pin connection strip

12 34 56 78 9 1110

I/O

communication port

24V output (AC)

turn-on voltage for external,

customer-supplied three-way

reversing valve (AC operation)

external sensor

Fuse, main switch, emergency OFF switches and

safety measures to comply with local regulations and standards

circulation pump (PH)

(max. 2A)

STB

HT1

HT2

24Vdc

Ventilator

external three-way

reversing valve for

mains water

(AC operation)

flame-monitoring electrode

Note:

KIM

STK

PA Volt-free connection (bridge connector)

STB Flue gas monitor

FW Domestic hot water temperature sensor

FR Return-temperature sensor (return)

FS Safety-temperature sensor (safety)

FK Boiler water-temperature sensor (supply)

KIM Boiler identification module

MV Solenoid valve

STK Plug socket for additional equipment

HT Hand-held terminal

1) Only one room-temperature regulating

device may be connected.

Mains power source

230V

50 Hz

Max. permitted

fuse rating

10A

Bridge is conductive

(remove when connecting)

UBA terminal box

1.25 Ampere slow blow

external

230V controls

Volt free external

control device

*) remove wirebridge

when used

Volt free room

thermostat

when used with

230V timer *)

Connection box

(RTH converter)

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

GREEN AND YELLOW - EARTH ; BLUE - NEUTRAL ; BROWN - LIVE

As the colours of the wires in the mains lead of of the appliance may not correspond with the coloured markings identifying the terminals in your connector proceed as follows:

The wire coloured green and yellow must be connected to the terminal on the connector marked with the letter E or by the earth symbol or coloured green or green-and-yellow. The wire coloured brown must be connected to the terminal marked

with the letter L or coloured red. The wire coloured blue must be connected to the terminal marked with the letter N or coloured black.

WARNING

THIS APPLIANCE MUST BE EARTHED

Ensure that your appliance is connected correctly - if you are in any doubt consult a qualified electrician.

For location of individual components, see service section and the exploded views in this manual.

Page 19

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 19

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

1.10.1 External controls

The wall-mounted condensing gas boiler can be fitted with the following control devices:

– ON/OFF temperature controller, volt free;

– A room-temperature control device at 230V connected to

the connection plate (fig. 20, item 1).

– A modulating room-temperature control device at 24 Volt

connected to the connection plate (fig. 22, item 1) such as the 250 RF ModuLink and the

iRT controllers.

1.10.2 External 230V controls

z Loosen crosshead screw (fig. 18, item 1) on burner-control

unit (UBA).

z Swivel burner-control unit downwards.

z Open the back of the burner-control unit to the right

(fig. 19).

z Connect the black pre-wired lead to a permanent live

supply (from the same fused isolator as all other controls on the heating system), L N E.

z Feed the 230V switch live and neutral (from external

controls) through the cable lead.

z Identify the 230V terminal block by the shaded area and

230V label.

z Connect the switch live to terminal "1" and a neutral to

terminal "2" (fig. 20, item 1).

z Replace covers.

Fig. 18 Swivel the housing of the burner-control unit

downwards

Fig. 19 Open back of the burner-control unit

Fig. 20 Connection box in burner-control unit -

230V connection

NOTE

Terminal 3 (fig. 20, item 2) is not used.

Page 20

Installation1

20 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

1.10.3 Volt free external control device connection

z Connect the black pre-wired lead to a permanent live

supply (from the same fused isolator as all other controls on the heating system), L N E.

z Loosen crosshead screw (fig. 18, item 1) on burner-control

unit (UBA).

z Swivel burner-control unit downwards.

z Open the back of the burner-control unit to the right

(fig. 19).

z Lead the control device wire through the cable lead.

z Fix the wire to terminal 1 and 2 of the volt free connection

(fig. 21, item 1).

1.10.4 24 Volt modulating room-temperature control device connection

z Loosen crosshead screw (fig. 18, item 1) on burner-control

unit (UBA).

z Swivel burner-control unit downwards.

z Open the back of the burner-control unit to the right

(fig. 19).

z Connect the 24 Volt modulating room-temperature control

device at fig. 22, item 1 on pin 3 and 4.

1.10.5 Other connections

Connection of an external water tank for single devices 600 - 11S/19S/24S:

z Remove bridge (fig. 23, item 1).

z Connect sensor for external water tank.

Connection for a second LPG solenoid valve:

z Connect switch unit for a second solenoid valve

(accessory) at green plug (fig. 23, item 2).

Connection of a modulating pump:

z Connect modulating pump (accessory) at plug (fig. 23,

item 3).

Connection of an external switch contact for underfloor heating system:

z Open plug (fig. 23, item 4) connection.

z Connect underfloor heating header thermostat (volt free)

and in series.

Fig. 21 Connection box in burner-control unit -

volt free connection

Fig. 22 Connection box in burner-control unit -

24 Volt connection

Fig. 23 Other connections

Page 21

Installation 1

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 21

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

1.10.6 System example

NOTE

Example systems are to be regarded as schematic representations only.

Fig. 24 System example

Page 22

Initial start-up2

22 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

2 Initial start-up

2.1 Preparing the boiler for operation

2.1.1 Fill the heating system

z Set three-way valve to the middle setting (applicable for

24C only). This is done by pushing the lever on the threeway valve (fig. 25) with a screwdriver to the middle setting.

z If necessary open the CH flow and CH return maintenance

valves (fig. 26, item 1 and 2).

z Connect temporary hose (fig. 27).

z Open both stop valves.

CAUTION

DO NOT operate the condensing gas boiler if large amounts of dust are present, e.g. due to building work in and around the place of installation.

Fig. 25 Three-way valve

WARNING

The wall-mounted condensing gas boiler must not be activated at this stage.

Fig. 26 Maintenance shutoff valves

CH Flow

CH Return

DHW Hot

(combi only)

DHW Cold

(combi only)

Gas

Fig. 27 Connecting temporary hose

temporary

hose

stop

valve

stop

valve

double

check

valve

DHW

cold

return

Page 23

Initial start-up 2

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 23

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

z Fill the system to a pressure of 1.0 to 1.2 bar (fig. 28,

item 1). Max. water pressure is 1.5 bar.

z Shut both stop valves and disconnect the filling loop.

In the case of the 600 - 24C: Purge the hot-water circuit of air

z Bleed the hot-water heat exchanger via the vent screw on

the heating-circuit side (fig. 29, item 1).

z Open the maintenance valve for the cold-water inlet.

z Leave the hot water taps open until water begins to flow

freely.

To drain the system take the following steps:

z Close the DHW cold and the CH return valve.

z Connect temporary hose (fig. 30).

z Open the CH return stop valve to drain the system.

2.1.2 Checking for leaks

z Disconnect the system from the power supply.

z Check all sections of gas pipework and connections for

signs of leaks before starting up system for the first time. If a leak is detected during tightness testing, use an approved leak detector to check all connections for possible escapes. The product must be certified as a gas leak-testing agent. DO NOT allow the product to come into contact with electrical wiring.

Fig. 28 Pressure display

bar

120

°C

11 KW

Fig. 29 Purge the hot-water heat exchanger of air (applies

to type 600 - 24C only)

Fig. 30 Draining the system

Drain

temporary hose

Stop valve

DHW Cold

(combi only)

CH Flow

CH Return

Page 24

Initial start-up2

24 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

2.1.3 Purging air from the gas supply system

z Close the gas service valve.

z Unscrew the sealing closure of the gas connection-

pressure testing nipple by two turns (fig. 31).

z Purge system and appliance as per relevant procedures,

IGE/UP/1b. Ensuring all safety requirements are met.

z Open the gas service valve.

z Close the gas shutoff valve once more.

z Shut the sealing closure of the test nipple once more.

z Open cover for 2nd operating level (fig. 32, item 1).

z Start boiler up and move chimney sweep switch (fig. 32,

item 3) to position “1”.

The display shows (fig. 32, item 2) “

-.” or “ =.” to indicate that

the gas supply system is purged of air. Return chimney sweep switch to normal running position, that is position “0”.

2.1.4 Check combustion air/flue gas connection

Check to ensure that the correct combustion air/flue gas system has been fitted.

Check that the instructions included in the appropriate flue gas system installation manual have been followed.

Fig. 31 Purging air from the gas supply system

Fig. 32 Display and chimney-sweep switch

Type of gas Factory settings of gas burners

Natural gas H

When delivered ready for operation and set to Wobbe index

14.1 kWh/m

(referred to 15 °C, 1013 mbar), applicable for Wobbe index range 11.3 to 15.2 kWh/m

Inscription on gas-type indicating label: Category setting: 2H G 20_20 mbar

LPG

After adaptation by a CORGI registered installer, the unit can be run on LPG. Inscription on gas-type indicating label: Category setting: 3P G 31_37 mbar

Table 4 Gas-supply types

Page 25

Initial start-up 2

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 25

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

2.1.5 Checking the type of gas and supply

2.1.6 Adjusting the flow temperature

z Open the cover to the 2nd operating level (fig. 33, item 1).

z Adjust the knob (fig. 33, item 2) to the desired flow

temperature (table 6) for your particular installation.

2.1.7 Adjusting the hot-water temperature for 24C only

z Adjust the heat-retaining and outlet temperature (table 6)

using the hot-water temperature regulator (fig. 33, item 5).

Type of gas supply

Gas nozzles ∅ [mm]

Venturi

tubes

11S 19S/24(C)

Natural gas H (G20) 5.55 6.5

Standard

Venturi

tubes

LPG 3.40 4.15

Standard

Venturi

tubes

Table 5 Gas-nozzle diameter

CAUTION

The burner must only be put into operation with the correct nozzles (table 5).

NOTE

Observe stickers attached to Venturi tubes.

Controller

setting

Flow temperature

[°C]

Heat-retaining

temperature (only 24 C)

[°C]

Outlet temperature

(only 24 C)

[°C]

Hot-water temperature

of external tanks

[°C]

1 40 - 60 27

2 44 DO NOT use setting no. 2 31

3 48 40 40 34

4 53 43 43 38

5 58 46 46 41

6 62 49 49 45

7 67 52 52 49

8 71 55 55 52

9 76 58 58 56

10 80 60 60 60

Table 6 Temperature settings

Fig. 33 Control box

Key to Fig. 33:

1: Cover for second operating level

2: Flow temperature knob

3: Heat-capacity jumper

4: Heating capacity knob

5: Hot-water temperature knob

6: Green blocking plate

NOTE

Factory setting of the controller is "10" (around 83 °C).

NOTE

Factory setting of the controller is "10".

To avoid energy losses set the controller to setting "1" (fig. 33, item 5). Remove the green blocking plate before making the adjustment.

Page 26

Initial start-up2

26 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

2.1.8 Adjusting the hot-water temperature for external tanks

z Use the hot-water temperature regulator to adjust the

temperature (fig. 33, item 5) to the desired setting table 6.

2.1.9 Adjust the hot-water flow controller (applies to combi-unit 600 - 24C only)

Adjust the hot-water flow controller (fig. 34) to the desired setting:

– To increase the flow of hot water:

turn valve towards “+”.

– To reduce the flow of hot water:

turn valve towards “”.

2.1.10 Setting the heating capacity

Set the heating capacity (table 7), according to the amount of heat required, at the controller (fig. 33, item 4).

Fig. 34 Hot-water flow controller

NOTE

The unit is factory-adjusted to an output of 22 kW and a flow of 7 l/min

NOTE The controller is factory-adjusted to position “6”

Controller setting

Heating capacity [kW] (±5 %)

600 - 11 S 600 - 19 S 600 - 24 S 600 - 24 C

14.99.79.79.7

2 5.6 10.7 11.3 11.3

3 6.3 11.8 12.9 12.9

4 6.9 12.8 14.5 14.5

5 7.6 13.8 16.0 16.0

6 8.3 14.9 17.6 17.6

7 9.0 15.9 19.2 19.2

8 9.6 16.9 20.8 20.8

9 10.3 18.0 22.4 22.4

10 11.0 19.0 24.0 24.0

Table 7 Heating capacity

Page 27

Initial start-up 2

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 27

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

2.1.11 Measure gas-supply pressure (flow pressure)

z Open at least one radiator thermostat valve.

z Turn the chimney-sweep switch (fig. 35, item 4) to

position “1”.

z Loosen the screw plug on the gas test nipple (fig. 36) by

two turns.

z Attach the pressure-gauge connection hose to the gas test

nipple (fig. 37).

z Slowly open the gas shutoff valve.

z Turn the power switch (fig. 35, item 2) to position “I”.

The burner should ignite after about 30 seconds.

z Measure the gas connection pressure and note it down on

the report form.

The gas-connection pressure must be: for natural gas H min. 17 mbar, max. 25 mbar, nominal connection pressure 20 mbar for LPG min. 30 mbar, max. 50 mbar, nominal connection pressure 37 mbar.

z Detach the gauge-connection tube once more and close

the test nipple at the screw plug.

z Ensure that switch is returned to "0" after this task has been

carried out.

Ensure all disturbed joints and connections are checked for gas tightness on completion of tasks.

2.1.12 Check the gas/air ratio and adjust as required

z Turn mains power switch (fig. 35, item 2) and chimney-

sweep switch (fig. 35, item 4) to “0”.

z Unscrew the sealing closure of the burner-pressure testing

nipple by one turn (fig. 36).

z Connect the positive port of the pressure gauge with a

hose to the burner pressure measuring nipple (fig. 37).

z Turn mains power switch to “I” and chimney-sweep switch

to “1”.

z If the burner has fired after approx. 30 seconds, keep the

service button (fig. 35, item 3) pressed until “Y” appears on the display.

z Turn the hot-water temperature controller (fig. 35, item 1)

to “1”.

z Read the differential pressure.

The differential pressure (p

GAS–pAIR

) should total -5 Pa

(±5 Pa) (display on measuring gauge: -10 Pa to 0 Pa).

Fig. 35 Mains switch, service button and chimney-sweep

switch

CAUTION

The condensing gas boiler must not be activated at this stage.

Fig. 36 Measure the gas connection pressure

NOTE

If the required connection pressure is not available or too high, contact your gas supplier or TRANSCO.

Fig. 37 Check the gas/air ratio

Page 28

Initial start-up2

28 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

z If the gas/air ratio does not conform to specifications,

readjust at the setscrew (fig. 37, item 1).

z Turn mains power switch and chimney-sweep switch to “0”.

z Remove the measuring equipment and retighten the screw

in the burner-pressure measuring nipple.

z Readjust the hot-water temperature controller to its original

setting.

z Turn the mains power switch to “I”.

2.1.13 Gas rating test

z Isolate all other appliances.

z Set the boiler to maximum firing rate.

z Ensure that there is no modulating of the fan gas valve.

z Carry out the Gas Rating procedure as described in

"Essential Gas Safety' 3rd edition on pages 169-176.

2.1.14 Record readings

z Unscrew the corresponding sealing closure (fig. 38) on the

connection adapter for the combustion-air/flue-gas system and replace it once the measuring operation in question has been carried out.

Carbon monoxide content

2.1.15 Function testing

Measuring the ionisation current (fig. 39)

z Disconnect the system from the power supply.

z Loosen the plug-and-socket connector of the ionisation

electrode and connect the multimeter in series. On the measuring device, select the µ-direct current range. The measuring device must have a resolution of at least 1 µA.

z Reconnect the system to the power supply and turn the

chimney-sweep switch to “1”.

z Measuring the ionisation current. The ionisation current

being checked must measure >2 µA direct current.

z Enter the reading on the report form.

z Disconnect the system from the power supply.

Fig. 38 Measuring points on exhaust conduit

Key to Fig. 38:

1: Exhaust-fume temperature, CO

, CO, NO

2: Combustion-air temperature

CAUTION

The carbon monoxide values under vacuum must be smaller than 400 ppm or 0.04 Vol%. Values around or exceeding 400 ppm indicate a faulty burner adjustment, a dirty gas burner or heat exchanger, or a defective burner. Ensure that the cause of the fault is remedied immediately.

NOTE

During initial start-up and annual servicing, make sure that all control, regulating and safety devices are in full working order and, if applicable, check for correct adjustment.

Fig. 39 Measuring the ionisation current

Page 29

Initial start-up 2

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 29

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

z Remove multimeter and restore the plug-and-socket

connection to its original state.

z Turn the chimney sweep switch to position “0”.

z Reconnect the system to the power supply.

When the display shows “7” and the service button is pressed, the display turns to “c”. Press the Reset button. The display shows “r”.

2.1.16 Handing over

After completing the installation and commissioning of the system the installer should hand over to the householder by the following actions:

z Hand the User Manual to the householder and explain

his/her responsibilities under the relevant national regulations.

z Explain and demonstrate the lighting and shutting down

procedures.

z The operation of the boiler and the use and adjustment of

all system controls should be fully explained to the householder, to ensure the greatest possible fuel economy consistent with the household requirements of heating. Advise the User of the precautions necessary to prevent damage to the system and to the building in the event of the system remaining inoperative during frosty conditions.

z Explain the function and the use of the boiler heating

controls.

z Explain the function of the boiler fault mode. Emphasise

that if a fault is indicated, the boiler should be turned off and a registered local heating installer consulted.

z Explain and demonstrate the function of time and

temperature controls, radiator valves etc., for the economic use of the system.

Loss of system water pressure

z Explain that the dial on the control panel indicates the

central heating system pressure and that if the normal COLD pressure of the system is seen to decrease over a period of time then the systems needs to be topped up. If the pressure decreases frequently than a registered local heating installer should be consulted.

z After installation, commissioning and customer handover

instructions please complete the BENCHMARK appliance log book and leave this with the customer.

z IMPORTANT

A comprehensive service should be carried out annually. Stress the importance of regular servicing by a Corgi registered installer.

WARNING

Do not fire the boiler if the pressure has reduced to zero from the original setting.

Page 30

Inspection3

30 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

3 Inspection

3.1 Preparing the heating boiler for inspection

z Disconnect the system.

z Remove the burner housing or cover from the heating

boiler.

For further information, please refer to subsection 8.2 "Inspection and maintenance reports" on page 66 and fill out the Benchmark.

DANGER OF FATAL INJURY

due to electric shock when system is opened.

z Before opening the system:

disconnect the heating unit at the emergency OFF switch or the corresponding circuit breaker of the house power supply.

z Ensure that the heating system cannot be

reconnected by accident.

NOTE

If the gas supply pipes are to be disconnected from the burner, the housing MUST ONLY be removed by a qualified service technician and checked for tightness on reassembly.

Page 31

Maintenance 4

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 31

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

4 Maintenance

For further information, please refer to subsection 8.2 "Inspection and maintenance reports" on page 66 and fill out the Benchmark.

4.1 Clean the heat exchanger, burner and condensate trap

4.1.1 Cleaning the heat exchanger without dismantling

z Disconnect the system from the power supply.

z Close the gas shutoff valve.

z Loosen the fixing screw, remove casing and combustion-

chamber cover.

z Release plug-in connection of fan power lead (fig. 40,

item 1), burner-control unit fan control lead (fig. 40, item 2) and gas-burner assembly (fig. 40, item 3).

z Loosen union nut on gas valve assembly (fig. 40, item 4).

z Push safety plate out of way.

z Turn air suction tube and pull off from below.

z Swivel forward the air combination unit (fig. 41, item 1).

z Pull the air combination unit up and out of bayonet

connector (fig. 41, item 2) and remove via front of unit.

z Remove burner gasket (fig. 42, item 1).

z Remove rubber seal in combustion chamber by pushing

upwards from inside (fig. 42, item 2).

Fig. 40 Loosen the union nut and remove the cable

NOTE

The cleaning of the burner and heat exchanger described here should be carried out whenever there are signs of heavy soiling on the wallmounted condensing gas boiler. It is sufficient, during annual servicing, to clean the burner and heat exchanger with the help of an appropriate cleaning product and a soft brush and compressed-air hose (see following section). The heat exchanger can be dismantled completely for thorough cleaning if required (see “Cleaning the heat exchanger after dismantling” on page 33)

Fig. 41 Remove the air combination unit

Fig. 42 Remove burner gasket and rubber seal

Page 32

Maintenance4

32 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

z Remove burner by pulling upwards through the opening

(fig. 43).

z Remove the front casing shell of the combustion chamber.

This is done by releasing the four snap catches at the sides.

z Remove the hot surface ignitor (fig. 44, item 1) and

ionisation electrode (fig. 44, item 2). In the case of the hot surface ignitor: loosen the fixing screw of the hot surface ignitor, detach both earth (ground) leads and remove the retaining plate of the hot surface ignitor by pulling it upwards, withdraw the hot surface ignitor by pulling it upwards. In the case of the ionisation electrode: Swivel the retaining plate to one side and carefully remove the ionisation electrode by pulling it upwards.

z Clean the burner and both parts of the combustion

chamber with a compressed-air line or brush.

z Refit the heat exchanger by following the above procedure

in reverse order.

Fig. 43 Remove burner

NOTE

Maintain the specified clearance of approx. 25 cm between the ceiling and the combustion chamber cover.

Fig. 44 Remove the hot surface ignitor and ionisation

electrode

CAUTION

The gasket between the two halves of the casing shell should normally be replaced. Fit the new gasket by pressing in from the top on both sides, and without stretching. DO NOT attempt to cut the gasket to size.

CAUTION

The burner gasket must match the shape of the groove in the housing.

CAUTION

Check the heat-exchanger for leaks BEFORE reassembling the casing shells.

Page 33

Maintenance 4

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 33

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

4.1.2 Cleaning the heat exchanger after dismantling

z Disconnect the system from the power supply.

z Close the gas shutoff valve.

z Loosen the retaining screw and remove the casing.

z Close the heating shutoff valves and drain the system.

z Open snap closures and remove combustion-chamber

cover.

z Release plug-in connection of fan power lead (fig. 40,

item 1), burner-control unit fan control lead (fig. 40, item 2) and gas-burner assembly (fig. 40, item 3).

z Loosen union nut on gas valve assembly (fig. 40, item 4).

z Push safety plate out of way.

z Turn air suction tube and pull off from below.

z Swivel the air combination unit forward (fig. 41, item 1).

z Pull the air combination unit up and out of bayonet

connector (fig. 41, item 2) and remove via front of unit.

z Remove burner gasket (fig. 42, item 1) and rubber seal in

combustion chamber from top (fig. 42, item 2).

z Remove burner by pulling upwards through the opening

(fig. 47, item 1) and release the four retaining clips (fig. 47, item 2).

z Remove the front casing shell of the combustion chamber.

z Remove the hot surface ignitor (fig. 44, item 1) and

ionisation electrode (fig. 44, item 2). In the case of the hot surface ignitor: Loosen the fixing screw of the hot surface ignitor, detach both earth (ground) leads and remove the retaining plate of the hot surface ignitor by pulling it upwards, withdraw the hot surface ignitor by pulling it upwards. In the case of the ionisation electrode: Swivel the retaining plate to one side and carefully remove the ionisation electrode by pulling it upwards.

Fig. 45 Draining the system

Drain

temporary hose

Stop valve

DHW Cold

(combi only)

CH Flow

CH Return

CAUTION

Cut hot water on supply side by closing the heating shutoff valve.

CAUTION

Drain the system via the temporary filling loop (fig. 45) or the screw-in drain plug (fig. 46, item 1) located under the pump.

Fig. 46 Screw-in drain plug

Fig. 47 Remove burner and release retaining clips

Page 34

Maintenance4

34 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

z Remove securing pin on flow and return flow conduit

(fig. 48) of heat exchanger.

z Remove spiral heat exchanger by pulling towards front

(fig. 48). Drain any water remaining in the heat exchanger into the condensate trap.

z Remove the diffusion head (fig. 49, item 2) on the

underside of the heat exchanger by withdrawing the securing pin (fig. 49, item 1) and unscrewing the diffusion head.

z Clean the two casing shells of the combustion chamber,

heat exchanger and burner with water or compressed air.

Take care not to damage the fins of the heat exchanger.

Refitting (fig. 50) :

z Screw the diffusion head in as far as it will go on the

underside of the heat exchanger (the final turn of the heat exchanger increases the clearance between the pipes) and insert securing pin.

z Check to ensure that the heat exchanger has been fitted

the right way round. The upper securing-pin groove must be horizontal.

Fig. 48 Securing pin on spiral heat exchanger

Fig. 49 Removing the diffusion head

Fig. 50 Refitting the heat exchanger

NOTE

Excessive exhaust temperatures may be an indication of an incorrectly-fitted diffusion head.

CAUTION

Take care not to damage the insulation on the diffusion head.

Page 35

Maintenance 4

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 35

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Refit the heat exchanger by following the above procedure in reverse. Note the following:

– The gasket between the two halves of the casing shell

should normally be replaced. Fit the new gasket by pressing in from the top on both sides, and without stretching. DO NOT attempt to cut the gasket to size.

– Check the heat-exchanger for leaks BEFORE

reassembling the casing shells.

z Check O-ring seals (spiral), and replace as required.

z Smear the O-ring seal with a thin layer of silicone grease.

4.1.3 Cleaning the condensate trap

z Remove the trap from the sleeve with the lip seal facing

downwards (fig. 51, item 1) and withdraw it from the outlet (fig. 51, item 2).

z Remove the safety cover and clean the trap.

z Fill the syphon with water and then reassemble in reverse

order.

z Measuring the gas input pressure (flow pressure).

z Check the gas/air ratio.

z Leak test in operational condition.

z Measuring the carbon monoxide content.

z Carry out function testing.

4.2 Flushing out the hot-water heat exchanger

z Turn mains power switch to “0”.

z Shut cold-water tap (accessory).

z Open a hot-water tap (e.g. at the washbasin) and then

close it again in order to check the pressure of the water being supplied.

z Loosen the cable on the stand-by sensor.

z Release the plastic clip from the bottom insulation of the

hot-water heat exchanger and remove the insulation.

z Connect the system to a power flusher unit and flush it out.

z Remove temperature sensor for DWH warm out and stand-

by sensor, and replace with flushing hoses (fig. 52).

z Reassemble.

z Open cold-water tap (accessory).

z Open hot-water tap (e.g. at washbasin) and thoroughly

flush out system.

z Turn mains power switch to “I”.

Fig. 51 Removing the condensate trap

Fig. 52 Flushing out the hot-water heat exchanger

Page 36

Servicing5

36 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

5 Servicing

5.1 Operating codes

NOTE

If the code displayed on the burner-control unit is not listed under the operating codes or fault warnings, the burner-control unit itself is malfunctioning.

Display Display after

pressing the service button

Meaning

Buderus 600 - 11S/19S/24S/24C is ready for operation

Burner interval circuit, 10 min. from burner start-up

Waiting for activation of the three-way valve (if fitted) or pump

Stand-by activated, Buderus 600 - 11S/19S/24S/24C ready to provide heat or hot water

Initial safety period: self-testing of burner-control unit during burner start-up

Post- or pre-purging period of fan unit

Flow temperature at adjustment setting

Buderus 600 - 11S/19S/24S/24C running in heating mode

“Chimney-sweep” mode, flow-temperature controller bypassed, Buderus 600 - 11S/19S/24S/24C heating to previously-entered flow temperature.

Normal heating mode

Service mode

Buderus 600 - 11S/19S/24S/24C running in hot-water mode

Normal hot water mode

Reset

Page 37

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 37

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

5.2 Fault codes

Code Meaning

Safety sensor exceeds 100 °C

Possible cause

Action

1 Resistance in the installation is too high Check if not all (thermostatic) radiator valves are clogged

with dirt.

2 Heating capacity is too large for the installation Adjust the heating capacity (see subsection 2.1.10)

3 Safety sensor is faulty Measure if resistance over the sensor is correct.

If not replace safety sensor (see subsection 5.3.11, subsection 5.3.12, subsection 5.3.13)

4 Problem with the pump or pump cabling

(no circulation)

Check if the pump cabling is faulty or if the pump is stuck (see subsection 5.3.9)

5 Water pressure is too low in the installation Top up the system (see subsection 2.1.1)

Code Meaning

Temperature difference between the safety sensor and flow sensor is greater than or equal to 15 °K

Possible cause

Action

1 Resistance in the installation is too high Check if not all (thermostatic) radiator valves are closed or

clogged with dirt

2 Safety sensor is dirty or faulty Check the safety sensor for dirt. Measure if resistance over

the sensor is correct. If not replace safety sensor (see subsection 5.3.11, subsection 5.3.12, subsection 5.3.13)

3 Flow sensor is dirty or faulty Check the sensor, replace if necessary (see subsection

5.3.14, subsection 5.3.15, subsection 5.3.16)

4 Problem with the pump or pump cabling

(no circulation)

Check if the pump cabling is faulty or if the pump is stuck. Replace pump if necessary (see subsection 5.3.9 and subsection 5.3.10)

5 Water pressure is too low in the installation Top up the system (see subsection 2.1.1)

Code Meaning

Safety sensor rises faster than 5 °C/sec.

Possible cause

Action

1 Heating capacity is too large for the installation Adjust the heating capacity (see subsection 2.1.10)

2 Resistance in the installation is too high Check if not all (thermostatic) radiator valves are closed or

clogged with dirt

3 Safety sensor is dirty or faulty Check the safety sensor for dirt. Measure if resistance over

the sensor is correct. If not replace safety sensor (see subsection 5.3.11, subsection 5.3.12, subsection 5.3.13)

4 External domestic hot water tank is too small for the

heating capacity

Top up the system (see subsection 2.1.1)

Page 38

Servicing5

38 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Code Meaning

Bad plug-in connection at cable harness, or damaged wiring

Possible cause

Action

1 Cable harness is faulty Check cable harness for faults and bad connections

2 Connectors at the back of the UBA are loose or faulty Check the connectors at the back of the UBA

3 UBA might be faulty Check the UBA by temporarily connecting an other UBA

(see subsection 5.3.3)

Code Meaning

Flow sensor exceeds 100 °C

Possible cause

Action

1 Flow sensor is dirty or faulty Check the sensor, replace if necessary (see subsection

5.3.14, subsection 5.3.15, subsection 5.3.16)

2 There is a problem with the pump or pump cabling

(no circulation)

Check if the pump cabling is faulty or if the pump is stuck. Replace pump if necessary (see subsection 5.3.9 and subsection 5.3.10)

3 Water pressure is too low in the installation Top up the system (see subsection 2.1.1)

Code Meaning

F2 fuse malfunction, or flue gas thermostat active

Possible cause

Action

1 Water pressure is too low in the installation Top up the system (see subsection 2.1.1)

2 Heat exchanger is dirty Check for a dirty heat exchanger and clean if necessary.

(see subsection 4.1)

3 Flue gas retarder faulty or missing Check if the flue gas retarder is installed in the heat

exchanger

4 Heat exchanger has a problem Purge heat exchanger

Code Meaning

Flow sensor exceeds 100 °C

Possible cause

Action

1 Resistance in the installation is too high Check if not all (thermostatic) radiator valves are clogged

with dirt

2 Heating capacity is too large for the installation Adjust the heating capacity

3 Safety sensor is faulty Check the sensor and measure if resistance over the

sensor is correct. If not replace safety sensor (see subsection 5.3.11, subsection 5.3.12, subsection 5.3.13)

4 Problem with the pump or pump cabling (no circulation) Check if the pump cabling is faulty or if the pump is stuck

(see subsection 5.3.9)

5 Water pressure is too low in the installation Top up the system (see subsection 2.1.1)

Code Meaning

System error

Possible cause

Action

1 Boiler is in operation for DHW due to a dripping faucet Check for dripping faucets

Page 39

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 39

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Code Meaning

Short circuit in safety sensor

Possible cause

Action

1 Safety sensor is faulty Check the sensor and measure if resistance over the

sensor is correct. If not replace safety sensor (see subsection 5.3.11, subsection 5.3.12, subsection 5.3.13)

2 A short or bad connection in the cable harness Check the cable harness and/or connector of the sensor

3 UBA might be faulty Check the UBA by temporarily connecting a different UBA

(see subsection 5.3.3)

Code Meaning

Safety sensor has a loose connection or is defective

Possible cause

Action

1 Safety sensor faulty or disconnected Check the sensor and measure if resistance over the

sensor is correct. If not replace safety sensor (see subsection 5.3.11, subsection 5.3.12, subsection 5.3.13)

2 A short or bad connection in the cable harness Check the cable harness and/or connector of the sensor

3 UBA might be faulty Check the UBA by temporarily connecting a different UBA

(see subsection 5.3.3)

Code Meaning

Short circuit in flow sensor

Possible cause

Action

1 Flow sensor is dirty or faulty Check the sensor, replace if necessary (see subsection

5.3.14, subsection 5.3.15, subsection 5.3.16)

2 A short or bad connection in the cable harness Check the cable harness and/or connector of the sensor

3 UBA might be faulty Check the UBA by temporarily connecting a different UBA

(see subsection 5.3.3)

Code Meaning

Flow sensor interrupted

Possible cause

Action

1 Flow sensor faulty or disconnected Check the sensor and measure if resistance over the

sensor is correct. If not replace safety sensor (see subsection 5.3.14, subsection 5.3.15, subsection 5.3.16)

2 A short or bad connection in the cable harness Check the cable harness and/or connector of the sensor

3 UBA might be faulty Check the UBA by temporarily connecting a different UBA

(see subsection 5.3.3)

Page 40

Servicing5

40 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Code Meaning

Boiler shut down after connection with Service Tool

Possible cause

Action

1 Service tool connection Press reset. If fault code remains than try to temporarily

connect a different UBA (see subsection 5.3.3)

2 A short or bad connection in the cable harness Check the cable harness and/or connector of the sensor

3 UBA might be faulty Check the UBA by temporarily connecting an other UBA

(see subsection 5.3.3)

Code Meaning

F1 fuse defective, or no ionisation message after ignition

Possible cause

Action

1 There is no flame, ionisation electrode doesn’t

glow, fan is turning

– Check wiring of the hot surface ignitor, measure the resistance

of the hot surface ignitor (should be between 50 and 300 Ohm). Replace hot surface ignitor if necessary (see subsection 5.3.19 and subsection 5.3.20)

– Check the UBA’s F1 fuse, replace if necessary

2 There is no flame, ionisation electrode does

glow, fan isn’t turning

– Check the fan and KIM connectors and the UBA fuses

3 There is no flame, ionisation electrode and fan

are working

– Check and adjust the gas/air ratio (see subsection 2.1.12)

– Check for 24 V~ on the gas valve during start up

– Check the gas-supply pressure (see subsection 2.1.11), this

should be higher than 20 mbar for natural gas.

– Check the earthing cable connections

(yellow/green wire).

– Check the cabling on the ionisation electrode

4 There is a flame, but the flame disappears

when the fan starts up

– Check the gas-supply pressure (see subsection 2.1.11), this

should be higher than 20 mbar for natural gas.

– Check and adjust the gas/air ratio (see subsection 2.1.12)

– Check the earthing cable connections (yellow/green wire)

– Check the cabling on the ionisation electrode

– Press reset. If fault code remains than try to temporarily connect

a different UBA (see subsection 5.3.3)

Page 41

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 41

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Code Meaning

Ionisation message, but no flame

Possible cause

Action

1 There is no flame, ionisation electrode doesn’t

glow, fan is turning

– Check wiring of the hot surface ignitor, measure the resistance

of the hot surface ignitor (should be between 50 and 300 Ohm). Replace hot surface ignitor if necessary (see subsection 5.3.19 and subsection 5.3.20)

– Check the UBA’s F1 fuse, replace if necessary

2 There is no flame, ionisation electrode does

glow, fan isn’t turning

– Check the fan and KIM connectors and the UBA fuses

3 There is no flame, ionisation electrode and fan

are working

– Check and adjust the gas/air ratio (see subsection 2.1.12)

– Check for 24V – on the gas valve during start up

– Check the gas-supply pressure (see subsection 2.1.11), this

should be higher than 20 mbar for natural gas.

– Check the earthing cable connections (yellow/green wire).

– Check the cabling on the ionisation electrode

4 There is a flame, but the flame disappears

when the fan starts up

– The gas valve doesn’t close properly. If there is still more than

20 V~ on the gas valve when there is no heat demand then check the UBA by temporarily connecting a different UBA.

– Check ionisation electrode/circuit (see subsection 2.1.15 and

subsection 5.3.22)

– When both the UBA and the ionisation electrode/circuit are OK,

then replace the gas valve

– Press reset. If fault code remains than try to temporarily connect

a different UBA (see subsection 5.3.3)

Code Meaning

Flame dies out after gas valve is opened

Possible cause

Action

1 Gas/air ratio not in order Check and adjust the gas/air ratio (see subsection 2.1.12)

2 Gas supply pressure may need adjusting Check the gas-supply pressure (see subsection 2.1.11),

this should be higher than 20 mbar for natural gas

3 Earthing cable may be faulty Check the earthing cable connections (yellow/green wire)

4 Ionisation electrode may be faulty Check the cabling on the ionisation electrode

Code Meaning

Flame goes out during warm-up phase

Possible cause

Action

1 Gas/air ratio not in order Check and adjust the gas/air ratio (see subsection 2.1.12)

Gas supply pressure may need adjusting

Check the gas-supply pressure (see subsection 2.1.11), this should be higher than 20 mbar for natural gas

3 Earthing cable may be faulty Check the earthing cable connections (yellow/green wire)

4 Ionisation electrode may be faulty Check the cabling on the ionisation electrode

Page 42

Servicing5

42 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Code Meaning

Voltage in burner-control unit too low (lower than 187 V~) or too high (higher than 246 V~)

Possible cause

Action

1 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

Code Meaning

Mains supply interrupted

Possible cause

Action

1 A problem with the mains supply Carry out a power test procedure for safe testing of the

mains electrical supply

2 Reset button pressed too briefly Press the Reset button until "r" appears in the display

Code Meaning

F3 fuse defect, or burner control unit error

Possible cause

Action

1 Short circuit in the 24V circuit (three-way-valve or

connector)

Check for a short circuit and replace the F3 fuse

2 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

Code Meaning

Voltage peaks in the UBA

Possible cause

Action

1 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

Code Meaning

Internal UBA error

Possible cause

Action

1 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

Page 43

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 43

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Code Meaning

Gas fault

Possible cause

Action

1 External switching contact (e.g. temperature-

monitoring device for underfloor heating has been tripped or gas pressure too low

Check gas pressure detector is defective or the wires have not been properly connected to the back of the UBA (see subsection 5.3.6)

Code Meaning

System error

Possible cause

Action

1 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

– Check for dripping hot water taps on the combination

boiler only

2 UBA may be defective Press reset. If fault code remains then try to temporarily

connect a different UBA

Code Meaning

KIM error

Possible cause

Action

1 KIM connected incorrectly or KIM defective Check the KIM connector and fan connector.

If the connectors are fine then contact Buderus

Code Meaning

9F/H

System error

Possible cause

Action

1 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

2 UBA may be defective Press reset. If fault code remains then try to temporarily

connect a different UBA (see subsection 5.3.3)

Code Meaning

Gas valve assembly error

Possible cause

Action

1 Wiring to the gas valve incorrect, or loose wiring

connections in UBA

– Check the electrical connections of the gas valve.

– Measure the resistance of the gas valve (18-55 Ohm)

– Check if for example induction fields interfere with the

regulating device

2 UBA may be defective – Press reset. If fault code remains then try to temporarily

connect a different UBA (see subsection 5.3.3)

3 Peaks in the electrical network – Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

Page 44

Servicing5

44 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Code Meaning

KIM defective

Possible cause

Action

1 KIM connected incorrectly or KIM defective Check the KIM connector and fan connector.

If the connectors are fine then contact Buderus

Code Meaning

E with

any character but

UBA defective

Possible cause

Action

1 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

2 UBA may be defective – Press reset. If fault code remains then try to temporarily

connect a different UBA (see subsection 5.3.3)

Code Meaning

Non compatible UBA fitted

Possible cause

Action

1 Regulating device may have to cope with interference – Check if for example induction fields interfere with the

regulating device

– Check if the are any peaks in the electrical network

caused by maybe windmills or a power generator

2 KIM connected incorrectly or KIM defective – Check the KIM connector and fan connector. If the

connectors are fine then contact Buderus

Problem: No DHW, despite the system being operational

– Set chimney sweep switch to "0"

– Check three-way valve replace if necessary

– Check DHW sensor and replace if necessary

Problem: No heating, despite that there is a demand for heat and the boiler is operational

– Check regulating device configuration and/ or the wiring

– Check the wiring between the regulating device and the UBA (see subsection 5.3.6)

– Check all the wiring

– Check the UBA and replace if necessary (see subsection 5.3.3)

Page 45

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 45

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

5.3 Checking and replacing parts

5.3.1 Checking the flue gas sensor

z Detach plug-and-socket connection on cable to flue gas

sensor. Ensure that no cable is earthed (grounded) at any point.

z Allow the flue gas sensor to cool down.

Activation temperature: 600 - 11S / 19S / 24S / 24C: 105 °C

z Check flue gas sensor for free throughput. If throughput is

not free, the flue gas sensor is defective.

z Replace any flue gas sensor found to be defective.

Ensure you use only genuine Buderus spare parts.

z If the flue gas sensor is working correctly, plug it in once

more.

5.3.2 Replacing the flue gas sensor

z Unscrew the flow-backup mounting.

z Detach the cable plug at the flue gas sensor.

z Loosen both retaining screws on the flue gas sensor.

z Remove the flue gas sensor and replace with a new unit

(fig. 53).

z Retighten the retaining screws.

z Reconnect the cable plug.

z Screw the mounting into place.

5.3.3 Replacing the UBA

z Disconnect the system from the power supply.

z Loosen crosshead screw (fig. 54, item 1) on UBA housing.

z Swivel UBA housing downwards.

Fig. 53 600 - 11S / 19S / 24S / 24C:

replacing the flue gas sensor

Fig. 54 Swivel UBA housing downwards

Page 46

Servicing5

46 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

z Open the UBA housing (fig. 55).

z Note the position of the cable plugs, disconnect all cable

plugs.

z Open the mains connection box by loosening the screw.

z Loosen the four screws and remove the strain-relief clamp.

z Carefully lift the UBA and remove by pulling forwards (snap

lock) (fig. 56).

z Fit new UBA.

z Reconnect all plug-in cables to their correct sockets.

z Feed the mains lead in through the strain-relief clamp in the

connection box and connect to the terminals as per the wiring diagram.

z Retighten the strain-relief clamp and shut the connection

box.

z Shut the mains connection box.

z Shut the UBA housing.

z Swivel the UBA housing upwards and screw into place.

z Fit the casing.

z Connect system to mains power supply.

5.3.4 Checking the fan

z Set the mains switch to “0”.

z Disconnect the fan's plug and socket connection.

z Connect a multimeter (230 V AC).

z Turn the mains power switch to “I”.

z Take voltage reading at measuring device.

If the voltage reading is 230 V, the power supply is in order.

z Set the mains switch to “0”.

z If the power supply is in order, plug the unit in once more.

z Turn the mains power switch to “I”.

z If the fan now fails to run, it must be replaced.

z If the fan runs at only partial load (i.e. effective operation of

the boiler is not possible), troubleshooting should start at the connection cable to the UBA or UBA.

Fig. 55 Opening the UBA housing

Fig. 56 Carefully lift the UBA to remove

Fig. 57 Checking the fan

Page 47

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 47

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

5.3.5 Replacing the fan

z Shut the gas valve.

z Disconnect the system from the power supply.

z Disconnect the fan, using the plug and socket from the

power supply (fig. 58, item 1), loosen the UBA control line at the fan (fig. 58, item 2) and the gas burner fitting (fig. 58, item 3).

z Loosen the union nut (fig. 58, item 4) on the gas burner

fitting.

z Push the safety plate out of the way (fig. 59, item 1).

z Turn air suction tube and pull off from below.

z Swivel the gas combination unit forward (fig. 60, item 1)

z Remove the gas combination unit from its bayonet

connector and pull upwards to detach (fig. 60, item 2).

Fig. 58 Replacing the fan on the 600 Series:

loosen plug and union nut

Fig. 59 Replacing the fan on the 600 Series:

remove the air suction tube

Fig. 60 Replacing the fan on the 600 Series:

remove the gas connection unit

Page 48

Servicing5

48 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

z Detach the fan by loosening the 2 x 2 screws on the

connection unit.

z Replace the fan.

z Refit by following the above procedure in reverse.

5.3.6 Checking the wiring connections of the UBA

z Disconnect the system from the power supply.

z Loosen crosshead screw on UBA housing.

z Swivel UBA housing downwards.

z Open the UBA housing.

z Check all cable terminals for tightness and

resecure/retighten as required.

z Shut the UBA housing.

z Swivel the UBA housing upwards and screw into place.

z Connect system to mains power supply.

5.3.7 Checking the mains supply

If the mains supply is interrupted or seems faulty, carry out a power test procedure for safe testing of the mains electrical supply.

z Loosen crosshead screw on UBA housing.

z Swivel UBA housing downwards.

z Open the UBA housing.

z Carry out the power test procedure (see fig. 63, item 1).

z Shut the UBA housing.

z Swivel the UBA housing upwards and screw into place.

z Connect system to mains power supply.

Fig. 61 Replacing the fan on the 600 Series:

replace the fan

NOTE

Once installation has been completed successfully, carry out leak testing as per subsection 2.1.2.

Fig. 62 Checking the wiring connections of the UBA

Fig. 63 Checking the mains supply

Page 49

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 49

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

5.3.8 Checking the miniature fuses

z Disconnect the system from the power supply.

z Loosen crosshead screw on UBA housing.

z Swivel UBA housing downwards.

z Open the UBA housing.

z Check miniature fuses (fig. 64) for correct functioning,

or carry out visual inspection. If defective, fit new fuse. All fuses a rated 230 Vac - 1.25 AT.

z Shut the UBA housing.

z Swivel the UBA housing upwards and screw into place.

z Connect system to mains power supply.

5.3.9 Checking the pump

z Remove screw plug on the pump (fig. 65).

z Turn the UBA mains power switch to “I”.

z Check to ensure that the pump is running. The pump’s

running mechanism may become blocked if the heating system has been out of use for an extended period. Use a screwdriver to rotate the pump in its normal running direction and release the blockage in question. If this procedure does not work, replace the pump.

z If the pump is working correctly, screw the plug back in.

5.3.10 Replacing the pump

z Disconnect the system from the power supply.

z Shut the servicing valve.

z Drain the 600 - 11S / 19S / 24S / 24C as per the

"Installation and Servicing Instructions".

z Loosen the screw on the terminal box (fig. 66, item 2) of the

pump and open the terminal box. Note the wiring layout, and loosen the cables (fig. 66, item 1).

z Loosen the screw-in connections on the pump (fig. 66,

item 3) and remove the pump.

z Fit new pump and connect to system.

z Connect cables in previously-noted order inside terminal

box, close terminal box and screw shut.

z Connect system to mains power supply.

z Open servicing valves.

Fig. 64 Checking the miniature fuse

Fuse Function

1 Hot surface ignitor

2 UBA, sensors, thermostat valve

3 UBA, three-way valve

Fig. 65 600 - 11S / 19S / 24S / 24C:

checking the pump

Fig. 66 600 - 11S / 19S / 24S / 24C:

replacing the pump

NOTE

Fill the 600 - 11S / 19S / 24S / 24C and purge the system of air.

Page 50

Servicing5

50 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

5.3.11 Checking the safety sensor

z Unplug cable connection from sensor.

z Measure resistance of sensor (fig. 67, item 1).

z Use a second-reading thermometer to measure the

temperature around the sensor.

z Compare readings with values shown intable 8 on

page 52. If there is any mismatch (i.e. > 5%), the sensor is defective.

z If the sensor is working correctly, plug it in once more.

5.3.12 Replacing the safety sensor

z Shut the servicing valve.

z Drain the 600 - 11S / 19S / 24S / 24C as per the

"Installation and Servicing Instructions".

z Loosen the plug-in connection (fig. 68, item 1).

z Unscrew the sensor (fig. 68, item 2) and replace with a new

unit.

z Plug in cable connection.

z Open servicing valves.

5.3.13 Checking the safety sensor connection lead

Check to ensure that all plug-in connections on the sensor and UBA are in order. Note that an incorrectly-inserted plug can lead to the generation of error messages. Start up the boiler by pressing the “reset” button.

z Set the mains switch to “0”.

z Disconnect the system from the power supply.

z Unplug cable connection from flow sensor.

z Disconnect 18-pin plug from UBA.

z Use a continuity tester to check the cable between the

plug-in connection and the 18-pin plug in the UBA. The test should be carried out on connections 06-18 and 08-18 (fig. 69).

z If the cables are in order, plug them in.

z Connect system to mains power supply.

z Turn the mains power switch to “I”.

Fig. 67 600 - 11S / 19S / 24S / 24C:

checking the safety sensor

Fig. 68 600 - 11S / 19S / 24S / 24C:

replacing the safety sensor

NOTE

Fill the 600 - 11S / 19S / 24S / 24C and purge the system of air.

Fig. 69 600 - 11S / 19S / 24S / 24C:

checking the safety sensor connection lead

Page 51

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 51

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

5.3.14 Checking the flow sensor

z Unplug cable connection from sensor.

z Measure resistance of sensor (fig. 70, item 1).

z Use a second-reading thermometer to measure the

temperature around the sensor.

z Compare readings with values shown in table 8 on

page 52. If there is any mismatch (i.e. > 5%), the sensor is defective.

z If the sensor is working correctly, plug it in once more.

5.3.15 Replacing the flow sensor

z Shut the servicing valve.

z Drain the 600 - 11S / 19S / 24S / 24C as per the

"Installation and Servicing Instructions".

z Loosen the plug-in connection (fig. 71, item 1).

z Unscrew the sensor (fig. 71, item 2) and replace with a new

unit.

z Plug in cable connection.

z Open servicing valves.

5.3.16 Checking the flow sensor connection lead

z Set the mains switch to “0”.

z Disconnect the system from the power supply.

z Unplug cable connection from flow sensor.

z Disconnect 20-pin plug from UBA.

z Use a continuity tester to check the cable between the

plug-in connection and the 20-pin plug in the UBA. The test should be carried out on connections 05-20 and 18-20 (fig. 72).

z If the cables are in order, plug them in.

z Connect system to mains power supply.

z Turn the mains power switch to “I”.

Fig. 70 600 - 11S / 19S / 24S / 24C:

checking the flow sensor

Fig. 71 600 - 11S / 19S / 24S / 24C:

replacing the flow sensor

NOTE

Fill the 600 - 11S / 19S / 24S / 24C and purge the system of air.

Fig. 72 600 - 11S / 19S / 24S / 24C:

checking the flow sensor connection lead

110

2011

UBA

Page 52

Servicing5

52 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

5.3.17 Checking the hot water / boiler sensor

z Disconnect the plug-and-socket connection on the hot

water sensor cable (fig. 73, item 1) and/or the boilersensor (fig. 73, item 2).

z Measure resistance, take a temperature reading at the

thermal pressure gauge (tolerance ± 5 K) and compare with the values listed in table 8. If there is any marked mismatch, the hot-water sensor is defective.

z If the hot water / boiler sensor is in order, plug it back in.

Table 8 Resistance values for hot water / boiler sensor

(approximate values)

Fig. 73 Checking the hot water / boiler sensor

Fig. 74 Boiler temperature sensor diagram

Temperature [°C] Resistance [Ω]

0 29,490.0

5 23,462.0

10 18,787.0

15 15,136.0

20 12,268.0

25 10,000.0

30 8,197.0

35 6,754.0

40 5,594.0

45 4,656.0

50 3,893.0

55 3,271.0

60 2,760.0

65 2,339.0

70 1,990.0

75 1,700.0

80 1,458.0

85 1,255.0

90 1,084.0

95 1,939.6

100 1,817.2

Fig. 75 Outside temperature sensor diagram

(°C)

R (Ω)

-20

-15

-10

-5

50,00020,000 80,00040,00030,00010,000 60,000 70,000

Outside temperature sensor

Page 53

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 53

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

5.3.18 Changing the hot water / boiler sensor

z Shut the servicing valve.

z Drain the 600 - 11S / 19S / 24S / 24C as per the

"Installation and Servicing Instructions".

z Disconnection plug-and-socket connection on cable to

hot water / boiler sensor.

z Remove insulation mounting (fig. 76, item 1) and detach

insulation.

z Pull out the sensor fuses (fig. 77).

z Unscrew hot water / boiler sensor and replace with new

unit.

z Refit insulation and corresponding mounting elements.

z Plug cable connection in once more.

z Open servicing valves.

z Fill the 600 - 11S / 19S / 24S / 24C and purge the system

of air as indicated in the installation and servicing instructions.

5.3.19 Checking the hot surface ignitor

z Disconnect the system from the power supply.

z Loosen crosshead screw on UBA housing.

z Swivel UBA housing downwards.

z Open the UBA housing.

z Unplug and remove hot surface ignitor from UBA housing

(fig. 78).

z Check hot surface ignitor for free throughput.

If throughput is free, the hot surface ignitor is in order.

z If the hot surface ignitor is in order, plug the cable into the

UBA housing.

z Shut the UBA housing.

z Swivel the UBA housing upwards and screw into place.

z Connect system to mains power supply.

Fig. 76 Changing the hot water / boiler sensor

Fig. 77 Changing the hot water / boiler sensor

Fig. 78 Checking the hot surface ignitor

Page 54

Servicing5

54 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

5.3.20 Replacing the hot surface ignitor

z Disconnect the system from the power supply.

z Remove combustion-chamber cover.

z Remove the earth (ground) lead from the hot surface

ignitor (fig. 79, item 1).

z Loosen crosshead screw on UBA housing.

z Swivel UBA housing downwards.

z Open the UBA housing.

z Unplug hot surface ignitor connection cable from UBA

housing (fig. 80).

z Loosen nut on clamp used to secure earth (ground) lead

(fig. 79, item 2).

z Detach retaining plate of hot surface ignitor (fig. 79, item 3)

and remove hot surface ignitor.

5.3.21 Measuring the ionisation current

z Disconnect the system from the power supply.

z Loosen the plug-and-socket connector of the monitoring

cable and connect the measuring device in series. Select the µA direct current range on the multimeter. The multimeter must have a resolution of at least 1 µA.

z Reconnect the system to the power supply and turn the

chimney-sweep switch to “1”.

z Measure the ionisation current.

The ionisation current must be > 2 µA DC.

z Enter the reading on the report form.

z Disconnect the system from the power supply.

z Remove the measuring device and restore the

plug-and-socket connection to its original state.

z Turn the chimney-sweep switch to position “0”.

z Refit the cover for 2nd operating level.

z Reconnect the system to the power supply. When the

display shows “7”, press the service button to display “c”. Press the "reset" button. The display shows “r”.

Fig. 79 Replacing the hot surface ignitor

Fig. 80 Disconnect the plug-in cable from the UBA housing

Page 55

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 55

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

5.3.22 Replacing the ionisation electrode

z Remove the CombiVENT air combination unit.

z Loosen the plug-and-socket connection of the ionization

electrode.

z Loosen screw (fig. 81, item 1) by a half-turn and slide bar

to remove.

z Pull electrode to remove, and fit new unit.

z Reassemble by following the above procedure in reverse.

5.3.23 Checking the three-way motorised valve for correct operation

z Disconnect the system from the power supply, set mains

switch to "0".

z Dismantle condensate trap.

z Remove protective cap from three-way valve.

z Remove bottom insulation from internal hot-water reservoir

(applies to 600 - 24C only).

z Push in catch on regulating motor and

z Remove bayonet connector by twisting anticlockwise.

z Remove regulating motor.

z Set the mains switch to “I” and press the “reset” button.

z Once the 600 - 11S / 19S / 24S / 24C is in operation, open

one of the hot-water taps. The UBA displays "

=. " for hot water. If the regulating

motor starts up (check for movement of adjusting lever), the motorised head is working.

z Shut the hot-water tap.

z Set the mains switch to “0”.

z If the motorised head is working, attach the regulating

motor and lock into place by twisting the bayonet connector.

z Connect the system to the power supply, set the mains

switch to “I” and press the “reset” button.

Fig. 81 Replacing the ionisation electrode

Fig. 82 600 - 11S / 19S / 24S / 24C:

checking the motorised head for correct operation

Page 56

Servicing5

56 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

5.3.24 Replacing the motorised valve body control valve

z Shut the servicing valve and drain the

600 - 11S / 19S / 24S / 24C as per the "Installation and Servicing Instructions".

z Dismantle condensate trap.

z Remove protective cap from three-way valve.

z Remove bottom insulation from internal hot-water reservoir

(applies to 600 - 24 C only).

z Push in catch on regulating motor and remove bayonet

connector by twisting anticlockwise.

z Remove regulating motor.

z Remove the control valve with a spanner and fit a new unit

(fig. 83).

z Fit regulating motor and lock into place by twisting the

bayonet connector.

z Reconnect the cable plug.

z Set the mains switch to “I” and press the “reset” button.

5.3.25 Replacing the three-way valve

z Shut the servicing valve and drain the

600 - 11S / 19S / 24S / 24C as per the "Installation and Servicing Instructions".

z Dismantle condensate trap.

z Remove protective cap from three-way valve.

z Remove bottom insulation from internal hot-water reservoir

(applies to 600 - 24 C only).

z Push in catch on motorised valve head and remove

bayonet connector by twisting anticlockwise.

z Remove motorised head.

z Loosen the 3 compression nuts (fig. 84).

z Remove three-way valve and fit new unit.

z Tighten the 3 compression nuts.

z Fit motorised valve head and lock into place by twisting the

bayonet connector.

z Reconnect the cable plug.

Fig. 83 600 - 11S / 19S / 24S / 24C:

replacing the control valve

NOTE

Open servicing valves, fill the 600 - 11S / 19S / 24S / 24C and purge the system of air.

Fig. 84 600 - 11S / 19S / 24S / 24C:

replacing the three-way valve

NOTE

Replace the three-way valve only if leaking occurs on the screw-in pipe connectors.

A: Mains water, B: Heating, AB: Boiler flow line

NOTE

Open servicing valves, fill the 600 - 11S / 19S / 24S / 24C and purge the system of air.

Page 57

Servicing 5

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 57

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

z Connect the system to the power supply, set the mains

switch to “I” and press the “reset” button.

5.3.26 Checking the ERC/RC connections to the UBA

z Disconnect the system from the power supply.

z Loosen crosshead screw on UBA housing.

z Swivel the UBA housing downwards (fig. 85).

z Push in UBA housing on left-hand side and open to the

right (fig. 86).

z Check to ensure that ERC or RC are correctly connected

to 3 and 4.

z Terminals 1 and 2 should not be wired in any way.

The unit is supplied with a dummy connector between terminals 1 and 2 (fig. 87). The DC voltage at terminals 3 and 4 should be approx. 11.5 V. If this is not so, the UBA or the cable harness is defective.

z Shut the UBA housing once more.

z Swivel the UBA housing upwards and screw into place.

z Connect system to mains power supply.

z Set the mains switch to “I” and press the “reset” button.

5.3.27 Replacing the terminal strip

z Note order of cable terminals. Loosen all cables.

z Connect the cables, in the right order, to the new terminal

strip.

Fig. 85 Swivel UBA housing downwards

Fig. 86 Opening the UBA housing

Page 58

Servicing5

58 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

5.3.28 Checking connections at the ModuLink or iRT

z Check contact link between cable and ModuLink or

iRT.

z There should be a DC voltage of approx. 11.5 V at the

ModuLink or iRT.

5.3.29 Checking KIM connections

z Locate KIM on boiler frame under UBA housing.

z Check 4 pin connector (fig. 88, item 1) is fitted and secure.

Fig. 87 Checking the controller-device connections at the

boiler

Key to control-device connections:

Item 1: ON/OFF temperature controller

Item 2: ModuLink or

iRT room temperature controller (digital)

Item 3: I/O port / communication port

Item 4: Outdoor-temperature sensor

Item 5: Power supply 24 VAC/max. 6 VA

Item 6: Turn-on voltage for three-way valve (9+11)

NOTE

It is possible, in order to limit the source of errors, to disconnect the ModuLink or iRT from the boiler (bridge required at 3 and 4) and to install a conductor bridge at 1 and 2 (fig. 87). The heating and hot-water requirement is then passed via the potentiometer setting of the UBA.

Fig. 88 KIM connections

NOTE

This is not a serviceable part and any fault identified with this component, contact Buderus.

Page 59

Changing to another type of gas 6

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 59

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

6 Changing to another type of gas

Switch off the heating boiler

z Disconnect the system from the power supply.

z Close the gas shutoff valve.

z Loosen the fixing screw and remove cover.

z Open snap locks (fig. 89, item 1) and remove combustion

chamber cover.

z Loosen union nut on gas valve assembly (fig. 90, item 4).

z Release plug-in connection of fan power lead (fig. 90,

item 1), burner-control unit fan control lead (fig. 90, item 2) and gas-burner assembly (fig. 90, item 3).

z Push safety plate out of way (fig. 91, item 1).

z Turn air suction tube and pull off from below.

Fig. 89 Open snap locks

WARNING!

Work on components in contact with gas must only be carried out by a registered CORGI engineer.

Fig. 90 Loosen the union nut and remove the cable

Fig. 91 Remove safety plate

Page 60

Changing to another type of gas6

60 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

z Swivel the air combination unit forwards (fig. 92, item 1).

z Pull the air combination unit up and out of the bayonet

connector (fig. 92, item 2) and remove via the front of the unit.

Replacing a gas nozzle

z Undo the three screws (fig. 93, item 2) on the long side of

the gas fitting.

z Remove the gas nozzle and insert the correct gas nozzle

for the new gas type.

z Insert new seal (fig. 93, item 4).

z Remount all components in the reverse sequence.

z Cover stickers (fig. 94, item 1) with the new stickers

(2 pieces, included in conversion kit).

Starting up

z Start up the appliance following the procedure described in

the mounting and maintenance instructions.

z Include all seal areas concerned during mounting in the

gas-tightness check when in operation.

Fig. 92 Remove the air combination unit

Type of gas supply

Gas nozzles ∅ [mm]

Venturi

tubes

11S 19S/24(C)

Natural gas H (G20) 5.55 6.5

Standard

Venturi

tubes

LPG 3.40 4.15

Standard

Venturi

tubes

Table 9 Gas-nozzle diameter

Fig. 93 Replacing a gaz nozzle

WARNING!

Conversion to another gas type is implemented by installing/removing a gas nozzle (fig. 93, item 3) of the appropriate gas nozzle diameter (table 9).

Page 61

Changing to another type of gas 6

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 61

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

z Refit all covers.

Fig. 94 Place new stickers

Page 62

Appendix7

62 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

7 Appendix

7.1 Technical specifications

Dimensions Unit

600 Series wall-mounted condensing gas boiler

11S 19S 24S 24C

Type of gas supply as established in EN 437 (GB)

GB II

2H3P

20 mbar, 37 mbar

(natural gas H and LPG)

Rated thermal load for hot water tank

kW kW

4.5 - 10.5

4.5 - 13.0

9.0 - 18.2 9.0 - 23.0 9.0 - 23.0

Rated heating capacity for system temperature (modulating from 30° to 100°) Heating curve 75/60 °C Heating curve 40/30 °C

kW kW

4.3 - 10.0

4.9 - 11.0

8.6 - 17.4

9.7 - 19.0

8.6 - 22.0

9.7 - 24.0

8.6 - 22.0

9.7 - 24.0

Seasonal efficiency (SEDBUK) % 90.3 90.3 90.2 90.1

Central heating installation

Heating water temperature °C 40 - 80

ΔT at residual head of 200 mbar K <20

Max. operating overpressure of boiler bar 3.0

Volume heat exchanger heating circuit l 1.0

Pump stopping time heating circuit

Position 1

Position 2

min

Expansion vessel

Capacity of expansion vessel l 12

Admission pressure of expansion vessel bar 0.75

Hot water tank (type 24C)

Hot water capacity of heat exchanger l - - - 0.95

Outlet flow at 60 °C (ΔT = 50 °C) l/min - - -

6.5

(type 24C)

Adjustable hot water temperature °C 40 - 60

Minimum connection pressure bar 0.75

Maximum connection pressure bar 10

Page 63

Appendix 7

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 63

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Dimensions Unit

600 Series wall-mounted condensing gas boiler

11S 19S 24S 24C

Pipe connections

Gas inch / mm G1"

Ø22 mm

compression

fitting

Heating water mm Ø22 mm compression fitting

Domestic water mm Ø15 mm compression fitting

Condensate-water outlet inch G1"

Flue gas values

Condensate water quantity, natural gas, 40/30 °C

l/h 0.7 1.3 1.6 1.6

pH value of condensate water approx. 4.1

Exhaust-fume mass-flow rate Full load Part-load

g/s g/s

4.9

2.2

8.4

4.3

10.6

4.3

10.6

4.3

Exhaust-fume temperature, full load Heating curve 75/60 °C Heating curve 40/30 °C

°C °C

75 50

85 55

95 55

Exhaust-fume temperature, part-load Heating curve 75/60 °C Heating curve 40/30 °C

°C °C

65 40

70 45

full load, natural gas

standard test gas G20 % 9.2

full load, natural gas

standard test gas LPG % 10.3

Standard emission factor CO mg/kWh <22

Standard emission factor NO

mg/kWh <30

Flow pressure available for use Pa 35 60 100 100

Flue-gas system

Type of exhaust-fume connection C

, C33, C

Diameter of flue gas system mm 60/100

Electrical data

Mains connection voltage V 230

Electrical power consumption Full/Part load W 105/100 110/105 115/105 115/105

Electrical protection rating IPX4D

Boiler dimensions and weight

Height x Width x Depth mm 850 x 480 x 370

Weight (without casing) kg 39 40 40 45

Casing kg 7 7 7 7

Page 64

Appendix7

64 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

7.2 Short list of spare parts

The following are parts commonly required due to damage or expendability. Their failure or absence is likely to affect safety or performance of this appliance. For a pictorial representation of the part see the respective position number on the exploded view pictures on pages 7 and 8.

Description Product No.

46 Sealing ring 73561 47 Cable harness 73371 48 UBA 38324 49 Power switch 38340 50 Temp-pressure gauge 75300 51 UBA panel 38488 52 230V cable 75301 53 O-ring 73580s 54 O-ring 73584s 55 Return pump connection pipe 73616 56 1-speed pump / 3-speed pump 75302 / 75303 57 Expansion vessel 38461 58 Expansion vessel pipe 38621 59 Manifold assembly 20378 60 Pressure relief valve 73199 61 Spring set 73531 62 Connection house by-pass 38611 63 Clip by-pass 38483 64 Connection house three-way valve 38614 65 Spring set 73531 66 Connection housing pump 73617 67 Connection housing 38611 68 Clip 38475s 69 By-pass pipe 38610 70 DHW pipe (hot) 38601 71 Clip 38474s 72 DHW supply pipe 73614 73 Hot water sensor 38352 74 Boiler sensor 38353 75 Insulation hot water tank 38493 76 DHW pipe (cold) 38605 77 Flow regulator 38604 78 Three-way valve body 73118 79 Three-way valve cartridge 73499 80 Three-way valve cover 73520 81 Three-way valve head 73317 82 Ionisation electrode 38320 83 Hot surface ignitor 78105 84 Hot water tank 38600

– RTH converter 230V 78091

Description Product No.

1 Flow connection piece 73581 2 Automated air vent 38618 3 Hairpin heat exchanger 73582s 4 Flow sensor 38323 5 Clip 73056s 6 Flow pipe 73613 7 Clip flow pipe 38602s 8 Back part heat exchanger 73611

9 Seal heat exchanger 73578 10 Sealing ring burner 73571s 11 Burner 11S / 19S and 24(C) 73593 / 73594 12 Heat exchanger 73612 13 Front panel heat exchanger 73610 14 Sight glass 73576 15 Fastener 75132s 16 Ventilation cover 75135 17 Casing 38091 18 Condensate trap 73589 19 Syphon cap with seal 73124 20 Drain pipe condensate trap 75988 21 Syphon 75986 22 Sealing ring 73561 23 Flue gas sensor 73376 24 Sealing ring 73736 25 Flue gas pipe 73743 26 Flue gas pipe seal 73579 27 Condensate collector 73630 28 Lipring 73563 29 Combustion divider 73587 30 Insulation divider 73515 31 Fan 73366 32 Gas/air supply pipe 73570 33 Fan seal 73565 34 Venturi 11S / 19S and 24(C) 73567 / 73568 35 Gas valve 73278 36 Rectifier 38355 37 Suction pipe 73573 38 Gas pipe 73279 39 Concentric adapter 77463 40 Lip ring 77464 41 Adapter clip 38496 42 Bracket 38092 43 Cable duct 38463s 44 Ventilation cover seal 38456 45 Pipe duct 38462s

Page 65

Reports 8

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 65

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

8 Reports

8.1 Start-up report

z Please check off the start-up tasks carried out and enter

the corresponding readings.

Initial start-up tasks Remarks or measurement readings

1. Note down gas characteristics:

Wobbe-index Operating heat value

_____________________ kWh/m

2. Inspect to check for leaks (See section 2.1.2 on page 23)

3. Check combustion air/flue gas connection (See section 2.1.4 on page 24)

4. Checking the boiler equipment (change to another type of gas if necessary) (See section 2.1.5 on page 25)

5. Carry out adjustment settings (See section 2.1.8 on page 26)

6. Measure the gas connection pressure (flow pressure) (See section 2.1.11 on page 27)

_____________________ mbar

7. Checking and adjusting the gas/air -ratio

-content: at full load at part load

(See section 2.1.12 on page 27)

_____________________ Pa

_____________________ % _____________________ %

8. Leak test in operational condition

9. Measure carbon monoxide content (CO), vacuum (See section 2.1.14 on page 28)

_____________________ ppm

10. Function testing

Measuring the ionisation current (See section 2.1.15 on page 28)

_____________________ µA

11. Fit the boiler casing

12. Instruct the user. Fill in Benchmark log book. Hand over documentation. (See section 2.1.16 on page 29)

13. Confirm initial start-up

Confirmation of initial start-up by qualified service technician

(Company stamp, signature)

Page 66

Reports8

66 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

8.2 Inspection and maintenance reports

Please check off the inspection and/or requirement-related maintenance tasks carried out and enter the corresponding readings.

The inspection and maintenance reports provide an overview of all the tasks and operations carried out.

z Sign details of inspection and maintenance tasks,

indicating date carried out.

See also Section 3: "Inspection“ on page 30 or Section 4: "Maintenance“ on page 31.

Use only original replacement parts.

Inspection tasks Date: _____________ Date: _____________

1. Check general state of system

2. Visual inspection and function check of system

3. Check gas- and water-bearing components for

- leaks

- signs of corrosion

- signs of ageing

4. Take system out of service and check the burner, heat exchanger and syphon for signs of dirt and soiling. (See section 4.1.1 on page 31)

5. Check the burner, hot surface ignitor and ionisation electrode, after disconnecting the system. (See section 4.1.1 on page 31)

6. Measuring the ionisation current (See section 2.1.15 on page 28) _________________ µA _________________ µA

7. Measure the gas connection pressure (flow pressure) (See section 2.1.11 on page 27) ________________ mbar ________________ mbar

8. Check the gas-air ratio (See section 2.1.12 on page 27) _________________ Pa _________________ Pa

9. Gas leak test in operational condition (See section 2.1.2 on page 23)

10. Measure the carbon monoxide content (CO), vacuum (See section 2.1.14 on page 28) ________________ ppm ________________ ppm

11. Pressure-testing of heating system:

- admission pressure of expansion tank

(see installation instructions supplied with expansion tank)

- Filling pressure

________________ mbar

12. Check ventilation and exhaust conduits for correct functioning and safety

13. Check requirement-related adjustment settings of control device (see documentation supplied with control device)

14. Final check of inspection tasks, with record kept of measurement readings and test results

15. Confirm inspection carried out by qualified service engineer and fill out the Benchmark

Company stamp / Date / Signature)

Page 67

Reports 8

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 67

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Date: _________ Date: ___________ Date: ___________ Date: ___________ Date: ___________

_______________ µA _______________ µA _______________ µA _______________ µA _______________ µA

_____________ mbar _____________ mbar _____________ mbar _____________ mbar _____________ mbar

_______________ Pa _______________ Pa _______________ Pa _______________ Pa _______________ Pa

______________ ppm ______________ ppm ______________ ppm ______________ ppm ______________ ppm

_____________ mbar

Page 68

Reports8

68 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Requirement-related maintenance tasks Date: _____________ Date: _____________

1. Clean heat exchanger, burner and condensate trap (See section 4.1 on page 31)

2. Check and adjust the gas-air ratio CO

-content: at full load at part load

(See section 2.1.12 on page 27)

______________________

3. Confirm servicing work Confirmation of servicing carried out by qualified technician

Company stamp, signature)

Page 69

Reports 8

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 69

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Date: ___________ Date: ___________ Date: ___________ Date: ___________ Date: ___________

___________________

____________________

___________________

____________________

___________________

____________________

___________________

____________________

___________________

____________________

Page 70

Notes

70 Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006

Buderus • http://www.buderus-domestic.co.uk Subject to modifications resulting from technical improvements!

Page 71

Notes

Installation and maintenance instructions for wall-mounted condensing gas boiler 600 - 11S/19S/24S/24C • 02/2006 71

Subject to modifications resulting from technical improvements! Buderus • http://www.buderus-domestic.co.uk

Page 72

Heating system specialist:

Buderus

Cotswold Way

Warndon Worcester WR4 9SW

Telephone: 01905 - 752 936

Fax: 01905 - 753 130

www.buderus-domestic.co.uk

Buderus is a trading name of BBT Thermotechnology UK Ltd.

Customer Services:

Technical Product Support:

Sales:

Returns:

Spares:

Tel: 0870 - 421 5933

Tel: 0870 - 421 5944

Tel: 01905 - 752 640

Tel: 01905 - 752 531

Tel: 01905 - 752 576

Fax: 01905 - 456 445 / 455 394

Fax: 01905 - 455 392

Fax: 01905 - 754 620

720.967A - 4612 - 02/2006