Patent Pending
Model: RPBOF
USER MANUAL
Please visit www.bofwaterpark.com for full assembly video
TABLE OF CONTENTS
Warning and Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Assembling the Waterpark Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Attaching the Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operating the Waterpark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Storing the Waterpark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
WARNINGS AND SAFETY INSTRUCTIONS
Observe the following warnings and safety instructions to reduce the likelihood of serious or fatal injury. Save these instruction for future
reference.
WARNING: CHOKING HAZARD CONTAINS SMALL PARTS. ADULT ASSEMBLY AND SUPERVISION REQUIRED.
Drowning Hazard - supervision of an adult required at all times
Do NOT allow children to assemble this product
Do NOT allow children to climb or swing from the waterpark
NEVER leave children unattended while the waterpark is in use.
Do NOT leave water in the bucket or basins; empty after use.
Do NOT attempt to move the waterpark when it is filled with water or has water/sand in the basins.
Ensure all connections are secure before attaching water supply
Surfaces may become slippery, ensure proper precautions are taken
Do NOT allow children to install batteries
Do NOT mix battery types or mix old and new batteries
IMPORTANT
Intended for children 2 years and up
Store inside and do NOT use if temperature is below 32°F
Use clean water in play basin and rinse thoroughly between uses
CONTENTS
TOOLS (Not Included)
• Rubber Mallet (Do NOT use a metal hammer)
• Phillips Head Screwdriver
• Scissors (may be required to cut funnel hose)
• Measuring Tape (optional)
OTHER SUPPLIES/ACCESSORIES (Not Included)
• Clean, Filtered Play Sand (if desired)
• (3) AA Batteries
• Bubble solution
• Water/Sand and Riding Toys
ASSEMBLING THE WATERPARK STRUCTURE
Helpful Tips to a Quick Build:
• Construct on a flat, firm surface - this will help when tapping components
together
• Tap components together after the structure is fully assembled - easier to take
apart if a wrong component is installed
• Wear gloves with a rubber coating - provides additional grip on the PVC
components
Item Description Qty
A Funnel Hose 1
B Dump Bucket 1
C Funnel 1
D Bucket Support Rod 1
E Water And Sand Basins 2
F Bucket Support Arm (Left) 1
G Bucket Support Arm (Right) 1
H Bucket Feed Line 1
I Table Upright With 4 Way 1
J Main Water Feed (Top) 1
K Main Water Feed (Bottom) 1
L Cross Feed Line 1
M 36" Pipe (Bottom/Table Support) 1
N 33.5" Pipe (Lateral Supports) 3
O 30.5" Pipe (Table Upright - Top) 1
P 24" Pipe (Front Upright - Top) 1
Q 17.25" Pipe (Table Support) 4
R 16" Pipe (Table Upright - Bottom) 2
S 12" Pipe (Table Support) 3
T Table Legs 2
U 24" Pipe With Coupling (Front Upright - Bottom) 1
V 3 Way Tee (Purple) 2
W Elbow (Yellow) 3
X 3 Way Elbow (Red) 2
Y 4 Way Elbow (Green) 1
Z Bucket Spout 1
AA Bubble Maker Straps 2
BB Self Taping Screws 2
CC Automatic Bubble Maker 1
NOTE: The hose connector and o-rings for the unions are in a separate
bag with the screws and Velcro straps.
• A measuring tape can be used to help identify components if needed
INSTRUCTIONS
IMPORTANT: Please pay additional attention to the orientation of the components
when placing them together. Connectors need to face the correct direction for
proper assembly.
IMPORTANT: Hand fit all the components at first. When fully assembled, tap the
unglued components lightly with a rubber mallet (Do NOT use a metal hammer).
IMPORTANT: To reduce leaking, ensure the o-rings are installed in the (4) unions
prior to tightening.
NOTE: The hose connector and o-rings for the unions are in a separate bag.
1. Lay the blue pipe in descending order, as seen in the CONTENTS section of
the manual. This will help to identify the components (Fig. 1).
Fig. 1
2
2. Assemble the bottom support of the table (Fig. 2).
(1) M 36" Pipe (Bottom/Table Support)
(2) R 16" Pipe (Table Upright - Bottom)
(2) W Elbow (Yellow)
Fig. 2
3. Assemble the top cross support of the table (Fig. 3).
(1) I Table Upright With 4 Way
(2) Q 17.25" Pipe (Table Support)
(1) V 3 Way Tee (Purple)
(1) Y 4 Way Elbow (Green)
Fig. 4B
Fig. 4C
Fig. 3
4. Construct the water and sand tables (Fig. 4A - 4C).
(3) S 12" Pipe (Table Support)
(2) Q 17.25" Pipe (Table Support)
(2) X 3 Way Elbow (Red)
(2) T Table Legs
(1) V 3 Way Tee (Purple)
5. Stand the table upright (resting on the yellow elbows/green caps) and install
the top upright (Fig. 5).
(1) O 30.5" Pipe (Table Upright - Top)
Fig. 5
Fig. 4A
6. The following steps will cover the assembly of the opposite side to the water
and sand tables (Fig. 6A - 6C). NOTE: Use an O-ring when connecting the
union
(1) J Main Water Feed (Top)
(1) K Main Water Feed (Bottom)
(2) N 33.5" Pipe (Latteral Supports)
(1) W Elbow (Yellow)
(1) P 24" Pipe (Front Upright - Top)
(1) U 24" Pipe With Coupling (Front Upright - Bottom)
3
Connect by tightening the union.
Fig. 6A
Fig. 7A
Stand the structure and align the union with the water and sand table structure.
Tighten the union to connect the two structures
Fig. 6B
Fig. 6C
7. Connect the two halves of the waterpark together by attached the Cross Feed
Line and install the lateral support for the bucket assembly (Fig. 7A - 7C).
NOTE: Use an O-ring when connecting the union.
(1) L Cross Feed Line
(1) N 33.5" Pipe (Lateral Supports)
Fig. 7B
Fig. 7C
8. Assemble the Dump Bucket (Fig. 8A - 8D).
(1) B Dump Bucket
(1) D Bucket Support Rod
(1) F Bucket Support Arm (Left)
(1) G Bucket Support Arm (Right)
Lay out the components as shown, ensuring the yellow and red elbows are
arranged properly. In addition, ensure the counterweight, inside the bucket
(identified by the arrow), is in the correct position (Fig. 8A).
Connect by tightening the union. Stand the structure and align the union with
the water and sand table structure. Tighten the union to connect the two
structures
Fig. 8A
4
Insert Support Rod (D) into the Right Support Arm (G) as shown (Fig. 8B).
Fig. 8B
Slide Dump Bucket (B) onto Support Rod (D) as shown (Fig. 8C).
Fig. 8C
Slide Left Support Arm (F) onto Support Rod (D) as shown (Fig. 8D).
11. Connect the Bucket Spout (Z) to the Bucket Feed Line (H) as
shown (Fig 11A and 11B)
IMPORTANT: Turn from the bottom of the spout, and do NOT over tighten. A
snug fit is all that is needed. Do NOT force the spout to finish a rotation. It does
not have to be tightened all the way to work properly.
Fig. 11A
Fig. 8D
9. Attach the Dump Bucket Assembly to the waterpark structure as shown (Fig. 9).
Fig. 9
NOTE: The Dump Bucket should tilt slightly toward the center of the waterpark. If
it is tilting away from the center, the bucket may be installed backwards - please
check the location of the counterweight.
10. Connect the Bucket Feed Line (Fig 10A and 10B). NOTE: Use an O-ring
when connecting the union.
(1) H Bucket Feed Line
Tighten the union from the Cross Feed Line and secure the front end with
the yellow elbows from the Bucket Support Arms as shown (Fig. 10)
Ensure that the spout is in line with the Bucket Feed Line and the center of the
Dump Bucket (Fig. 11B).
Fig. 11B
12. Using a rubber mallet (Do NOT use a metal hammer), lightly tap all the non glued components together to ensure they are secure and square.
.
Fig. 10
The assistance of a second person to hold the opposing side when tapping
connections together will make this step easier.
13. Secure the hose connector to the Main Water Feed (K) and ensure the gasket
is in place.
5
ATTACHING THE ACCESSORIES
IMPORTANT: Before attaching accessories, it is recommended to place the
waterpark in the location it will be used.
1. Insert AA batteries (NOT included) into the Bubble Maker. Attach the Bubble
Maker (CC) to the center of the top lateral pipe, across from the water and
sand tables using Straps (AA) as shown (Fig. 12).
Fig. 12
2. Secure the Funnel to the front upright.
Fig. 14
NOTE: Scissors may be necessary to cut the hose to the desired length.
3. Insert the (2) Water and Sand Basins (E) into the table frames (Fig. 15).
IMPORTANT: Tap all connections together prior to installing bins. Use a
rubber mallet and tap front to back and side to side, ensuring the pipes are
all the way inside the fittings.
IMPORTANT: Do NOT screw into any pipe that has a union or is designated
as a "feed line". Look at the location of the funnel before screwing into the pipe.
(1) A Funnel Hose
(1) C Funnel
(2) BB Self Tapping Screws
Using a Phillips head screw driver, attach the funnel just above the coupling
of the front upright, opposite of the water and sand tables as shown (Fig. 13).
-
Fig. 15
OPERATING THE WATERPARK
WARNING: Do NOT allow children to use the waterpark unless there is proper
supervision.
WARNING: NEVER leave children unattended while the waterpark is in use.
Fig. 13
Insert the Funnel Hose (A) into the bottom of the Funnel (C) and then wrap
the hose twice around the upright. Secure the hose to the bottom of the
upright with a Self Tapping Screw (BB) by screwing through the inside
portion of the hose only as shown (Fig. 14).
WARNING: Do NOT leave water in the bucket or basins; empty after use.
WARNING: Ensure all fittings are secure before operating the waterpark.
WARNING: Surfaces may become slippery, ensure proper precautions are taken
IMPORTANT: Ensure the waterpark is in the location where it will be used. Do
NOT attempt to move the waterpark when it is filled with water or has water/sand
in the basins.
6
1. Use a garden hose to fill one or both basins with water. Only fill the basins
halfway with water.
2. Fill a second basin, if desired, with clean, filtered play sand (NOT
INCLUDED). Only fill half way with sand .
3. Add bubbles to the Bubble Maker. Press and release the top button to turn
On/Off.
4. Secure the garden hose to the waterpark as shown (Fig. 16).
Fig. 16
5. Gradually opening the valve to the full position. Allow water to flow through
the entire waterpark until it pours out of the spout, into the Dump Bucket.
NOTE: The Dump Bucket may continuously spin when the hose valve is fully
open. This step is just to fill the entire waterpark.
6. Gradually turn the garden hose valve to reduce the water supply to the
waterpark until the dump bucket stops spinning and catches water.
NOTE: A good flow of water allows the bucket to dump once every 25 - 35
seconds.
NOTE: Monitor the area around the waterpark for puddles and move the
waterpark accordingly.
STORING THE WATERPARK
WARNING: Do NOT leave water in the bucket or basins; empty after use.
IMPORTANT: Do NOT use or leave water in the waterpark if temperatures fall
below 32°F.
IMPORTANT: Do NOT attempt to move the waterpark when it is filled with water
or has water/sand in the basins.
NOTE: The waterpark does not need to be disassembled between uses.
1. Turn the water supply to the OFF position.
2. Release the hose from the waterpark connector (water will flow from the pipe).
3. Remove both basins and empty any water basin.
NOTE: If sand is used in the second basin, the first basin can be used as a c
over to keep sand clean.
4. Empty any water left in the Dump Bucket.
5. Using the front uprights, gently tilt the waterpark upward, lifting the front a
few inches. This will allow excess water to escape through the open hose
connector.
6. Move the waterpark to a shaded area away from heavy traffic.
NOTE: For longer term storage it is good practice to release a few
connections to ensure all water has been emptied from the waterpark.
For assistance please contact our support line at (732) 719-9195
7
Thank you for purchasing
Buckets of Fun 6-in-1
Backyard Waterpark!
We know your kids will have a blast!
We'd love to share in the excitement, so please post your
images, videos and comments to Facebook and Instagram.
Please find us @backyardwaterpark and use
#hadbucketsoffun.
"My kids #hadbucketsoffun with their new backyard
waterpark!"
Thank you!
Loading...