1
1
6
7
2
8
3
4
5
A
B
C
067226 HD/HC/HS4658
L/N/NT4658N
574048
574098 AM5658
This devices features a PIR and US (ultrasound) movement detector, and a brightness
sensor for automatic activation of various types of loads following the detection of a
movement, and a brightness level lower than the set level.
The enabling/disabling of the load can also be performed manually using the
appropriate front pushbutton and/or using an external BUS control device.
IT is possible to configure several operating modes; for the detailed descriptions see
page 4.
Description
1. PIR sensor
2. LEARN LED
3. US sensor
4. ON-OFF button
5. LEARN button
6. Movement detector sensor (under the lens)
7. Infrared transmitter (under the lens)
8. Brightness sensor
Voltage: 27 V=
Current draw: 17 mA
Connection between sensor and actuator: SCS BUS connector
Sensor type: movement detector (PIR+US) with 180°
detection angle and brightness sensor.
Flush mounted box depth: 40 mm
Weight: 60 g
Impact resistance: IK04
Penetration of solids and liquids: IP20
Time delay: from 5 sec to 59 min. 59 sec
Brightness: from 20 lux to 1275 lux
Operating temperature: from - 5 °C to + 45 °C
Storage temperature: from - 20 °C to + 70 °C
Technical data
Dimensional data
Front view
Legend
Size: 2 flush mounted modules
A B C
45 45 51
PIR+US ush-mounted SCS Green Switch
MQ00473-f-EN 09/06/2014
Standards, Certifications, Marks
Directive:
– Electromagnetic Compatibility Directive 2004/108/EC
Installation regulations:
– CEI 64-8
Product regulations:
– IEC 60669-2-1
– EN 50428
Environmental regulations:
– EU Directive 2002/96/EC: WEEE (Waste Electrical and Electronic Equipment)
– EU Directive 2002/95/EC: RoHS (Restriction of Hazardous Substances)
2
PIR US
≥ 2,5 m
1 m
2,5 m
067226 HD/HC/HS4658
L/N/NT4658N
574048
574098 AM5658
Positioning the sensor
Installation
Settings
Position the sensor so
that it is not affected by
the artificial light already
present in the room.
Sensor parameters Default value Adjustable parameters Configuration remote control
88230 88235
BMSO4001 BMSO4003
Time delay 15 mn
3,5,10,15,20 min
−
30s - 255 h 59 min 59s
−
Sensitivity PIR (very high) / US (high) Low, medium, high, very high
Brightness threshold 300 lux
20, 100, 300, 500, 1000 lux
−
0 - 1275 lux
−
Operating
mode
Auto Not active ON/OFF
Walkthrough ON ON/OFF
Eco Not active ON/OFF
Detection
mode
Initial PIR and US PIR and/or US, PIR, US
−
Holding PIR or US PIR and/or US, PIR, US
−
Retrigger PIR or US PIR and/or US, PIR, US, OFF
−
Alarm Not active ON/OFF
−
Advanced
mode
Calibration − 0 - 99995 lux
−
Adjustment Not active ON/OFF
−
Contribution of light Automatic Automatic - 1275 lux
−
PIR+US ush-mounted SCS Green Switch
MQ00473-f-EN 09/06/2014
Time delay
The period of time after which the load is switched off if no movement is detected.
The time restarts whenever the sensor detects a movement.
Sensitivity
Adjustment of the sensitivity of the detection technology used.
Brightness threshold
Lighting level below which the sensor activates the load and above which it
switches it off.
Operating mode:
Auto
The load is automatically switched on:
- upon detection of a movement if the level of natural light is insufficient.
The load is automatically switched off:
- if no movement is detected at the end of the set time delay + standby time.
- or if the level of natural light is insufficient (adjustment on).
Each new detection causes automatic switching on if the light is insufficient.
Walkthrough
Loading...