DIGITAL INSTANT HOT WATER DISPENSER INSTALLATION INSTRUCTIONS
We are delighted you have chosen the BTI Aqua-Solutions Digital Instant Hot Water Dispenser for use in your home. When used in con-
junction with a Hot & Cold or Hot Only BTI Aqua-Solutions Filtration Faucet, or any other open vented 3-line filtration faucet, this unit will
give you years of hot water whenever you require it.
Please read and follow this step-by-step guide to installation, operation, and care for the Digital Instant Hot Water Dispenser and you will
soon be making your rst cup of coffee, tea, soup, oatmeal or a variety of other items - instantly - and at optimal temperature!
TOOLS REQUIREDPARTS INCLUDED
• Adjustable wrench
• Phillips screwdriver
IMPORTANT - WHAT YOU NEED TO KNOW BEFORE YOU START
For your safety and a worry-free installation, please read and follow all the instructions, cautions and warnings BEFORE installation or
use of this Digital Instant Hot Water Dispenser. The BTI Aqua-Solutions Digital Instant Hot Water Dispenser is intended only for residential, not commercial use.
•
Make sure all electrical wiring, connections and water connections conform to local codes.
•
A standard 110V electrical outlet is required under the sink to power the Dispenser and must supply power CONTINUOUSLY to the
Dispenser.
•
The cord/plug supplied with the Dispenser must be connected to the power outlet.
• 3/8” x 5/16” hot-outlet adapter
• 3/8” x 1/4” cold-inlet adapter
•
The Digital Instant Hot Water Dispenser is a non-pressurized, open vented system with a built-in pressure regulator valve (PRV) that
limits operating pressure to 60 psi.
•
A Hot & Cold or Hot Only Filtration Faucet must be installed before the Digital Instant Hot Water Dispenser, creating an “open vent”
system, consequently, no pressure is built up inside the Dispenser.
REV 4/02/18
1
SAFETY INSTRUCTIONS - READ BEFORE YOU START
These instructions are only intended as a guide. If there is any doubt about installation,
please contact a licensed/certied plumber and/or electrician.
ENSURE THE DIGITAL INSTANT HOT WATER DISPENSER IS NOT CONNECTED TO ELECTRIC POWER DURING THE INSTALLATION.
•
•
Using an ungrounded or improper connection of the power supply to the product can cause serious injury or death from
electrical shock. ALWAYS use the USA IEC Power Cord supplied with the unit.
•
The Digital Instant Hot Water Dispenser must be mounted vertically and level. Because the Digital Instant Hot Water Dispenser is
not under pressure, there is a slight delay in water ow after the Hot & Cold or Hot Only Filtration Faucet handle is turned on. This
is normal and indicates the Digital Instant Hot Water Dispenser is functioning properly.
•
It is recommended that a “handle spring-back” type Filtration Faucet, like the BTI Aqua-Solutions 2100, 2200 or 2400 Series
Filtration Faucets, is used with the Digital Instant Hot Water Dispenser to protect the user from continuous dispensing of hot
water and possible injury from same.
•
Place the Digital Instant Hot Water Dispenser in position, check and ensure that the ltration faucet hoses and the power cord to
the electrical outlet will reach without being stretched.
ITEM HT4105
The Digital Instant Hot Water Dispenser must be positioned so the hoses to and from the Filtration Faucet do not twist or kink.
•
ELECTRICAL REQUIREMENTS
•
A 110V electrical power supply is required.
•
It is recommended that a separate circuit serving only the Digital Instant Hot Water Dispenser be provided OR use an outlet that
can be turned On/Off by a switch.
The Digital Instant Hot Water Dispenser is equipped with a power supply cord with a power plug. To minimize possible shock
•
hazard, the cord must be plugged into a mating ground-type outlet, grounded in accordance with all local codes and ordinances.
PLUMBING REQUIREMENTS
•
If local codes permit, the Hot & Cold or Hot Only Filtration Faucet hoses should be connected to hot and cold water supply lines
using shut-off valves.
•
The use of ltered, clean water with impurities removed is advised. Place a point-of-use ltration unit such as the BTI
Aqua-Solutions FL1000 in-line PRIOR to the Filtration Faucet.
•
Unltered water with impurities, grains of sand, etc., can clog the Dispenser and Filtration Faucet and cause the Dispenser’s
5-year warranty to be voided.
•
Connecting a standard, pressurized faucet may cause injury and will damage the electronic components of the Digital Instant Hot
Water Dispenser and void the 5-year warranty.
ENVIRONMENT REQUIREMENTS
••DO NOT install the Instant Hot Water Dispenser outdoors or in a location where the temperature may fall below 32ºF.
The installation environment should be ventilated, with protection from direct sunlight, in a humidity range of 10-70%.
2
HOW A VENTED FAUCET WORKS
OUTLETINLET
OUTLETINLET
Water ows from supply line (A) into the faucet base (B).
ITEM HT4105
Water is then diverted inside the faucet into line (C) and into the Digital
Instant Hot Water Dispenser (D).
The fresh water displaces hot water in the Dispenser, causing it to ow
freely through line (E) to the ltration faucet.
Hot water continues straight through the ltration faucet and exits
the spout, (F).
IMPORTANT!
NEVER OPERATE THE FAUCET IF THE CLEAR OUTLET TUBE (E) IS KINKED!
NEVER CONNECT AN INSTANT HOT WATER DISPENSER DIRECTLY TO A
STANDARD FAUCET. CONNECTION TO A FAUCET OTHER THAN A 3-LINE
VENTED FAUCET CAN CAUSE INJURY, INTERNAL DAMAGE TO DISPENSER
AND WILL VOID 5-YEAR WARRANTY.
INSTANT HOT WATER DISPENSER INSTALLATION PROCEDURE
1. FOR FLOOR-MOUNT INSTALLATION - CHOOSE LOCATION FOR DISPENSER
F
B
E
C
D
A
Find a location under the sink that has access to an
electrical outlet and is close enough to connect the
faucet lines without kinking them. For the unit to operate properly, it cannot be installed beyond the reach of
the manufacturer-provided electrical cord. Leave 1-2”
clearance around the Dispenser for air ow.
DO NOT PLUG IN THE INSTANT HOT WATER DISPENSER UNTIL IT IS FILLED WITH WATER.
HEATING THE DISPENSER WHILE EMPTY WILL DAMAGE THE UNIT AND VOID THE 5-YEAR WARRANTY.
2. CABINET-SIDE MOUNT
If mounting on side of cabinet,
install 2 screws into cabinet side that align with the
mounting holes on the back of the Dispenser.
Leave 1”-2” clearance around Dispenser for air ow.
WARNING!
3
3. BTI AQUA-SOLUTIONS HOT ONLY and HOT & COLD FILTRATION FAUCET W/ DIGITAL INSTANT HOT WATER DISPENSER
ITEM HT4105
3a
A
F
E
3b
Drill 1-3/8” hole in countertop.
Maximum counter thickness is 2”
Center the base plate with built-in
O-ring over the mounting hole on
the top of the countertop. Center the
faucet body on the base plate.
If desired, apply a thin bead of silicone
seal under the base plate for added
sealing.
DO NOT USE PLUMBERS’ PUTTY
Hoses are attached to faucet body as
B
C
D
G
I
shown in diagram.
A - Blue Label Cold Water-In Hose
B - Faucet Stem
C - Hot Only Faucet, Hot Handle
D - Black Label Pressure Tank Hose
E - Hot & Cold Faucet, Cold Handle
F - Blue Label Cold Water-In Hose
G - Faucet Stem
H - Black Label Pressure Tank Hose
I - Hot & Cold Faucet, Hot Handle
H
3c
For Hot Only Faucet: Place faucet
handle in desired position.
Fasten the faucet from under the
countertop by rst sliding the rubber
washer, then the metal washer onto
the faucet stem.
3d
Thread the mounting nut to the top
of the faucet stem and hand tighten.
Once the faucet is secure, tighten the
3 screws against the underside of the
countertop. This will prevent the faucet
from moving/spinning.
3e
Make sure to place the 3 screws on
the metal washer through the matching holes of the rubber washer and
slide both washers up to the bottom of
the countertop.
Place a metal pinch clamp on one
end of the clear hose and attach
the clear hose to faucet stem end.
Secure with pinch clamp.
3g
3f
Attach the braided blue label coldwater-in hose to cold-water supply
line.
Use plumbers’ tape on the outside
threads to provide a good seal.
Turn on the water supply and check for leak(s), ESPECIALLY at the water supply and connections points. If leak(s) are present, shut off the
water supply, repair the leak and re-test the system as described. Open the hot handle of the faucet and turn on the water supply. Water
will ow from the faucet when the dispenser is full.
FAUCET AND DIGITAL INSTANT HOT WATER DISPENSER!
Attach the braided black label
pressure tank hose to the blue
cold-water inlet on the dispenser.
Screw the tapered adapter onto the
red hot-water outlet. Use plumbers’
tape on the outside threads of the
outlet for a good seal.
Make sure that all lines are as straight
as possible and not kinked as this may
adversely affect the performance of
the dispenser.
ENJOY YOUR BTI AQUA-SOLUTIONS FILTRATION
3h
Place the remaining metal pinch
clamp on the open end of the clear
hose. Push the clear hose onto the
tapered adapter previously installed
on the red hot-water outlet. Secure
with pinch clamp.
4
4. INSTALLATION IF NOT USING BTI AQUA-SOLUTIONS FILTRATION FAUCET
4a4b
Screw 3/8” x 1/4” cold-inlet adapter onto blue
cold-water inlet (A) on top of Dispenser.
Screw 3/8” x 5/16” hot-outlet adapter onto red hot-water
outlet (B) on top of Dispenser.
ITEM HT4105
Connect cold-water line to BLUE cold-water inlet tting.
Connect hot-water line to RED hot-water outlet tting.
Push lines securely into ttings.
Make sure larger 5/16” adapter is put onto the red
hot-water outlet (B) on top of Dispenser.
IMPORTANT!
BEFORE the Instant Hot Water Dispenser is plugged into the power outlet, it must be lled with water and checked for tightness
and leaks. FOLLOW THIS PROCEDURE BEFORE CONNECTING DIGITAL INSTANT HOT WATER DISPENSER TO POWER.
1. Open all water valves to allow water to ow to the Filtration Faucet.
2. Turn the “spring-back handle” of any BTI Aqua-Solutions Hot Only or Hot & Cold Faucet (or equivalent) to the open
position and hold until the Dispenser is full and water ows through the faucet spout.
3. Release and close the “spring-back handle” and check all connections for water tightness and leaks.
4. Correct any leaking joints and re-test for water-tightness and leaks before connecting to power outlet.
5. Ensure the installation area is dry and no water is present.
6. Connect the plug to the power outlet and turn on the power outlet at the switch or breaker box.
7. The Digital Instant Hot Water Dispenser display panel will now light up with the On/Off button in the center illuminated.
Turn water supply back on.
5
BTI AQUA-SOLUTIONS DIGITAL INSTANT HOT WATER DISPENSER GUIDE TO OPERATION
REMEMBER TO ONLY PLUG THE DISPENSER IN AFTER THE
UNIT IS COMPLETELY FILLED WITH WATER
GETTING TO KNOW YOUR INSTANT HOT WATER DISPENSER
RAISE TO NEXT PRESET TEMPERATURE
ITEM HT4105
LOWER TEMPERATURE IN 3º INCREMENTS
LOWER TO NEXT PRESET TEMPERATURE
To power ON/OFF or to select VACATION MODE, simply press and hold center button for 3 seconds.
•
When the Dispenser is in heating mode, there will be a sequence of red/blue rings illuminating individually to indicate the
•
Dispenser is actively heating.
Once the desired temperature is reached, the dial’s red/blue rings will become static.
•
When the Instant Hot Water Dispenser is empty and is powered ON, the unit will automatically sense the situation. The
•
heating element will not engage and the “lack of water” will be indicated on the display panel by ashing a 208º
temperature reading.
When “lack of water” indicator is displayed, the dry-burn protection sensor has automatically activated.
•
RAISE TEMPERATURE IN 3º INCREMENTS
POWERS ON/OFF, SELECTS VACATION MODE
When “lack of water” indicator is ashing 208º, press the ON/OFF center button and hold for 3 seconds to power down the
•
unit. Then, ll the Dispenser and follow the starting procedures. When water is drawn from the Dispenser through the Hot
& Cold or Hot Only Filtration Faucet, OR the temperature inside the Dispenser falls by 6º F, the Dispenser will automatically
reheat the water to the desired setting.
TEMPERATURE ADJUSTMENT (for temperatures above 203º F)
The BTI Aqua-Solutions Digital Instant Hot Water Dispenser has been set for optimum performance in most common and known
situations. However, there are factors which may inuence the performance of the Dispenser, such as incoming water
temperature, atmospheric pressure, and altitude.
Should you experience any discharge of water from the Filtration Faucet spout during heat-up, you can reduce the temperature
setting to compensate by adjusting the unit in 3 degree increments until the water discharge is eliminated.
Consult the “High Altitude Cooking” information included.
6
ITEM HT4105
HIGH ALTITUDE COOKING
Common knowledge tells us that water boils at 212ºF, but that number only represents how water boils at sea level. With each 500 feet
of increased elevation, the boiling point of water is lowered by about one degree. That means if you’re cooking at the highest point in
South Dakota, you’re going to be boiling at just 198º, and food will take longer to cook because of decreased atmospheric pressure.
Most cookbooks consider anything more than 3,000 feet in elevation to be “high altitude,” putting most of the western United States in
the category. For food safety as well as taste, cooks in a high altitude region must cook food for longer, add moisture to most baked
goods, and consider marinating or braising meat.
BTI Aqua-Solutions’ Instant Hot Water Dispenser can be adjusted for your specic region. If you do not know your city’s specic
elevation, nd the highest point in your state in the chart below. For each 500 feet of elevation more than sea level, reduce 212º by one
degree to determine your local boiling point.
State Highest Point
Alabama
Alaska
Arizona
Arkansas
California
Colorado
Connecticut
Delaware
DC
Florida
Georgia
Hawaii
2,413’
20,310’
12,637’
2,753’
14,505’
14,440’
2,379’
447’
409’
345’
4,784’
13,803’
The BTI Aqua-Solutions Instant Hot Water Dispenser comes with seven pre-set commonly used temperatures:
State Highest PointState Highest PointState Highest Point
Idaho
Illinois
Indiana
Iowa
Kansas
Kentucky
Louisiana
Maine
Maryland
Massachusetts
Michigan
Mississippi
Missouri
12,668’
1,235’
1,257’
1,671’
4,041’
4,145’
535’
5,270’
3,360’
3,489’
1,979’
2,302’
807’
Montana
Nebraska
Nevada
New Hampshire
New Jersey
New Mexico
New York
North Carolina
North Dakota
Ohio
Oklahoma
Oregon
Pennsylvania
12,807’
5,427’
13,147’
6,288’
18,013’
13,167’
5,343’
6,684’
3,508’
1,549’
4,975’
11,249’
3,213’
Rhode Island
South Carolina
South Dakota
Tennessee
Texas
Utah
Vermont
Virginia
Washington
West Virginia
Wisconsin
Wyoming
811’
3,560’
7,244’
6,643’
8,751’
13,534’
4,395’
5,729’
14,417’
4,863’
1,951’
13,809’
OPTIMAL PRE-SET TEMPERATURES
167ºF
176ºF
185ºF
194ºF
203ºF
206ºF
208ºF
COFFEE
195º - 205ºF
TEA
167º - 194ºF
White/Green Tea 167ºF
Black/Oolong 185ºF
Chamomile 194ºF
SOUP
190º - 200ºF
COOKING
206ºF
7
BTI AQUA-SOLUTIONS INSTANT HOT WATER DISPENSER TROUBLESHOOTING GUIDE
THE UNIT DOES NOT HEAT WATER
The BTI Aqua-Solutions Instant Hot Water Dispenser will take between 8 and 10 minutes (from initial activation) to heat water to
the setting specied. If the unit is not heating water, make sure the unit is plugged into a 110V outlet that you have conrmed to
be operational. Test the outlet by plugging in another 110V item, such as a light. If the outlet is working and the unit is not heating
water, please contact BTI Client Support at 720.322.0800 for assistance.
THE FAUCET DRIPS OR SPITS FROM THE SPOUT
Although this is an “uncommon” occurrence with the BTI Instant Hot Water Dispenser unit, certain altitude conditions may make
the faucet drip/spit when the Instant Hot Water Dispenser is reheating water to replenish the unit’s water supply. Once the water
level in the dispenser is lled and heated, the dripping/spitting will cease.
THE WATER HAS AN ODOR OR TASTES FUNNY
ITEM HT4105
The BTI Instant Hot Water Dispenser contains NSF-approved, food-grade materials for the cold-water inlet and a 304 Stainless
Steel tank for the hot water reservoir. Using these materials and the quality control inspections at time of manufacturing elimi-
nates any leaching of chemicals into the unit. The common cause of odor or bad taste is the presence of unltered water being
heated by the unit. Upon heating the unltered water, the odors and taste are accentuated. The best solution to this problem is to
install a point-of-use ltration unit such as the BTI Aqua-Solutions FL1000 in conjunction with the Instant Hot Water Dispenser.
Make sure the ltration unit selected is certied to both NSF 42 and 53 standards to assure maximum protection. Once the water
is ltered, the bad odor and taste will not be present in heated water.
WARNING - IMPORTANT
THE BTI AQUA-SOLUTIONS INSTANT HOT WATER DISPENSER MUST ONLY BE USED WITH A 3-LINE VENTED FAUCET.
If connected to a non-vented faucet, the 5-year warranty will be void.
Additionally, the use of any in-line water chiller with any BTI Aqua-Solutions Filtration Faucet will void the 5-year warranty of
any BTI Aqua-Solutions Filtration Faucet and Instant Hot Water Dispenser.
www.btiaquasolutions.com
7022 S. Revere Pkwy Suite 240 • Centennial, CO 80112 • 720.322.0800 (o) 720.322.0801 (f)
8
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.