BTI Aqua-Solutions C2100, C2200, C2400, H2100, H2200 Installation Guide

FILTRATION FAUCET INSTALLATION INSTRUCTIONS

ITEM C2100	ITEM H2100	ITEM HC2100
ITEM C2200	ITEM H2200	ITEM HC2200
ITEM C2400	ITEM H2400	ITEM HC2400

5-3/8”

5-3/8”

4”

4”

4”

4”

9-1/2”

9-3/4”

9-3/4”

9-1/2”

9-11/16”

2-3/4”

2-3/4”

7-1/2”

7-1/2”

9-11/16”

6-3/4”

3-1/4”

3-1/4”

6-5/8”

6-3/4”

6-1/2”

6-1/4”

5-1/2”

6-1/4”

2-3/4”

2-1/8”

2-1/8”

2-1/8”

2-1/8”

2-1/8”

2-1/8”

4-1/4”

C2100 / H2100

HC2100

C2200 / H2200

HC2200

C2400 / H2400

HC2400

SHUT OFF WATER SUPPLY	TOOLS REQUIRED
BEFORE INSTALLATION	ADJUSTABLE WRENCH • DRILL • PLUMBERS’ TAPE
	PHILLIPS HEAD SCREWDRIVER

COLD ONLY FILTRATION FAUCET W/ FILTRATION SYSTEM

ITEMS: C2100, C2200, C2400

1

Faucet Stem

Base Plate

Rubber Washer

Metal Washer

Rubber Washer

Lock Washer

Lock Nut

Tube Insert

Ferrule

Compression Nut

1/4” Water Inlet

Tubing (supplied

with BTI Filtration

System FL1000)

Drill 3/4” to 1” in diameter hole in countertop. Maximum counter thickness is 2”

2

Center the base plate with built-in O-ring over the mounting hole on the top of the countertop. Center the faucet body on the base plate.

If desired, apply a thin bead of silicone seal under the base plate for added sealing.

DO NOT USE PLUMBERS’ PUTTY

3

Place faucet handle in desired position. Fasten the faucet from under the countertop, sliding large rubber washer, then metal washer, then smaller rubber washer, then 5/8” diameter serrated lock washer on the faucet stem, and secure with the lock nut so the faucet does not move/spin.

DO NOT OVER TIGHTEN

www.btiaquasolutions.com • 7022 S. Revere Parkway Suite 240 • Centennial, CO 80112 • 720.322.0800 (o) 720.322.0801 (f)

REV. 11/19/18

FILTRATION FAUCET INSTALLATION INSTRUCTIONS, page 2 of 4

COLD ONLY FILTRATION FAUCET W/ FILTRATION SYSTEM

ITEMS: C2100, C2200, C2400

4

Slide the metal 1/4” compression nut over the supply tubing (provided with the filtration system). Next, place the plastic ferrule (large end first) over the supply tubing into the compression nut.

If you are using the BTI Filtration System ITEM FL1000, you have ample tubing to connect to the faucet and still leave 4"-6” of extra tubing before the connection point.

5

Place the 1/2” long plastic insert into the end of the tubing and tighten the compression nut on the faucet stem.

TIGHTEN SECURELY WITH WRENCH.

6

* COMPLETE FILTRATION SYSTEM INSTALLATION USING INSTALLATION GUIDE INCLUDED WITH YOUR SPECIFIC BRAND OF FILTRATION SYSTEM.

Then, open the handle on the filtration faucet and turn on the water supply. Allow the water to run for 1-2 minutes to clear any debris that might be present in the water line.

7

Once a clean flow of water is achieved, check for leaks, ESPECIALLY at the water supply and connection points. If leak(s) are present, shut off the water supply, repair the leak and re-test the system as previously described.

FILTRATION SYSTEM INSTALLATION WITH BTI AQUA-SOLUTIONS HOT/COLD FILTRATION FAUCET

ITEMS: HC2100, HC2200, HC2400

A

G	C
F	D
	F
	E
	B

(A)FILTRATION FAUCET

(B)BTI FILTRATION SYSTEM-FL1000

(C)LINE/HOSE TO KITCHEN FAUCET

(D)ANGLE SHUT-OFF VALVE (supplied)

(E)COLD-WATER SUPPLY SHUT-OFF VALVE

(F)1/4” O.D. TUBING (supplied)

(G)3/8” / 1/4” ADAPTER (supplied w/faucet)

Install angle shut-off valve (D) supplied with BTI Filtration System.

Shut-off cold-water supply (E). Disconnect line/ hose (C) to kitchen faucet from cold-water supply shut-off valve (E).

Connect angle shut-off valve (D) to cold-water supply shut-off valve (E). Connect line/hose from kitchen faucet (C) to angle shut-off valve (D).

Cut the 1/4” O.D. inlet/outlet tubing (supplied) to the correct lengths, ensuring the cut ends are square and clean.

Push one end of tubing (F) into angle shut-off valve (D). Push other end of tubing into “L-Fitting”, pre-installed in the “inlet” on top of filter.

Connect 3/8” Female-Side of adapter (G) (supplied) to braided blue label cold-water in hose. Push one end of tubing

(F) into 1/4” Push-Fit Side of adapter (G). Push other end of tubing (F) into “outlet” connector on top of filter.

To remove a tube, push down on the collet while pulling on the tube.

Turn on the water supply and check for leaks. Flush at least one gallon of water through the system before use.

Write the installation and filter change dates on the label for future reference.