B-TECH BT7052/B, BT7052/C Datasheet

BT7052

This pack contains:
1 collar with covers

v.0209 OR1BX

Caution: Do not exceed the maximum weight limit indicated for this product.
Failure to comply may cause instability and possible serious injury.

This wall collar is intended for use only with the maximum
weights indicated. Use with heavier than the maximum
indicated may result in instability causing possible injury.

50mm (2 INCH) ACCESSORY
COLLAR WITH COVERS

O52

84

24

• Accessory collar for use with 50mm (2”) poles

• Provides attachment for B-Tech modulus system mounts

• Aesthetic cover plates included to hide fasteners

68

27

Important Safety Instructions.

Read first

Do not attempt to install this product until all instructions and warnings have been read and
properly understood. Please keep these instructions for future reference.
B-Tech International Limited, its distributors and dealers are not liable or responsible for
damage or injury caused by improper installation, improper use or failure to observe these
safety instructions. In such cases, all guarantees will expire.

General

B-Tech International Ltd recommends that a professional AV installer or other suitably qualified
person install this product. Great care must always be taken during installation as most AV
equipment is of a fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely,
then please consult a professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death both during installation and at
any time thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are
installing. This weight limit will be clearly stated on each product and its packaging and will
vary from product to product.

Product location

Please pay careful attention to where this product is located.
If located in a public or frequently populated area ensure that the product is out of the
immediate reach of people. If any AV equipment is to be suspended over the likely path or
location of people then great care should be taken to secure all parts of the installation from
falling.

Fixing hardware

It is highly recommended that all fixing screws be used where supplied and that the purpose of
all other fixing hardware is fully understood.
The installer must be satisfied that any supplied fixing hardware is suit able for each specific
installation. If any fixing sc rews or inc l ude d ha rd war e are deemed not suff ic i ent for a safe
installation then please consult a professional or your local hardware store.

Hazard limitation

Some products have moving parts and the potential to cause injury through the crushing or
trapping of fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up.
Immediately after installations doub le -check that the work done is safe and secure. Double­check all necessary fixings are present and are of ample ti gh tne ss .
It is recommended that periodic inspections of the product and its fixing points are made as
frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV
installer or other suitably qualified person.

Head Office

Bennett House, Long March, Daventry, Northants N N11 4NR, UK

Tel: [phone] Fax: [phone]

B-Tech International Ltd.

Email: [e-mail]

Made in China

Europe

Brixtonlaan 32, Zaventem 1930,Brussels, Belgium

Tel: [phone] Fax: [phone]

B-Tech PRO-AV bvba

Email: [e-mail]

www.btechavm ounts.c om

©Copyright 2009.

North America

B-Tech Audio Video Mounts.

10 Greg Street, #108, Sparks, NV 89431, USA

Tel: [phone] Fax: [phone]

Email: [e-mail]

B-Tech International (Hong Kong) Ltd.

23rd Floor, Manulife Tower, North Point, HK

Tel: [phone] Fax: [phone]

Email: [e-mail]

Asia Pacific

PAGE 1 / 3

BT7052

v.0209 OR1BX

PARTS LIST

PARTS LIST

6

5

2

1

Attention!

Ensure safety bolt (Pa rt 5)

is in place before any AV

equipment is fitted.

3

No

1 BT7052 COLLAR

2 M8 X 15mm GRUB SCREWS

3 M8 SPRING WASHER

M8 X 12mm FLAT CROSS HEAD

4

SCREW

5 M8 X 65mm SAFETY BOLT

6 BT7052 COLLAR COVER HALF PUSH FIT AROUND COLLAR 2

7 4mm ALLEN KEY

8 5mm ALLEN KEY

PART NAME DESCRIPTION QTY

TO FIT 50MM POLES

TO CLAMP COLLAR TO POLE

SITS UNDER SCREW HEADS

TO ATTACH ACCESSORIES

PASSES THROUGH POLE

TO TIGHTEN (PART 2)

TO TIGHTEN (PART 5)

1

2

5

4

1

1

1

4

3

Spare screws and

4

washers are provided

for use on the other

side of the collar if two

accessories need to

3

be attached.

Covers cannot be

used in this situation.

7

8

PLEASE KEEP THIS PARTS LIST FOR FUTURE REFERENCE

PAGE 2 / 3