BT7373
DESK MOUNT WITH ARTICULATED ARM
INSTALLATION GUIDE & PARTS LIST
This Pack Contains 1 Desk Mount
PLEASE KEEP THIS FOR FUTURE RE FERENCE
FEATURES
● Designed for screens up to 24" (61cm) / 9kg (20lbs)
● Fits screens with VESA mounting patterns:
75 x 75mm and 100 x 100mm
● Optional desk clamp and grommet included
● Easy tilt adjustment +/-40° tilt
● Maximum extension is 457m m (18”)
● Features three swivel points: 360° at pole,
360° at both pivot points and 180° at interface
● Simple installation with all mounting hardware included
CONTENTS
Installation Safety Notes.....................................................................................................................2
Parts List.............................................................................................................................................4
Installation Instructions.......................................................................................................................6
Product Dimensions..........................................................................................................................15
B-Tech Contact Details.....................................................................................................................16
INSTALLATION TOOLS REQUIRED
Crosshead
screwdriver
2.5mm Hex Key
(Supplied)
4mm Hex Key
(Supplied)
B-TECH AUDIO VIDEO MOUNTS
www.btechavmounts.com
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This mount is intended for use only with the maximum weights
indicated. Use with flat screens heavier than the maximum indicated may
result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and
properly understood. Please keep these instructions for future reference.
B-Tech International Limited, its distributors and dealers are not liable or responsible for
damage or injury caused by improper installation, improper use or failure to observe these
safety instructions. In such cases, all guarantees will expire.
General
Great care must always be taken during installation as most AV equipment is of a fragile
nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely,
then please consult a professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death bot h during installation and at
any time thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are
installing. This weight limit will be clearly stated on each product and its packaging and will
vary from product to product.
Product location
Please pay careful attention to where this product is located. Some locations are not suitable
for installation.
If located in a public or frequently populated area ensure that the product is out of the
immediate reach of people.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and that the purpose of
all other fixing hardware is fully understood. In some cases more AV equipment fixing
hardware will be supplied to accommodate different models of equipment and set up
configurations.
The installer must be satisfied that any supplied fixing hardware is suitable for each specific
installation. If any fixing screws or included hardware are deemed not sufficient for a safe
installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the
product might provide and ensure that all cables are tidy and secure. Check to see that any
moving aspect of the product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or
trapping of fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up.
Immediately after installations double-check that the work done is safe and secure. Doublecheck all necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as
frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV
installer or other suitably qualified person.
The articulating arm may spring upward and may cause injury or damage to the equipment
when the monitor is removed. Secure the arm by lifting the arm to highest position, to remove
monitor safely.
2
BT7373
PARTS LIST
9
20
9
1
11
5
10
12
2
23
GROMMET CLAMP
22
23
22
6
15
11
6
13
14
16
21
18
3
4
10
2
13
7
8
Suitable for loads
up to
9kg (20lbs)
4
19
17
18
24
REF PART NAME QTY
1 INTERFACE ASSEMBLY 1
2 ARM 2
3 HEIGHT ADJUSTMENT COLLAR 1
4 POLE ASSEMBLY 1
5 TOP CLAMP 1
6 CLAMP PLATE 2
7 BOTTOM CLAMP 1
8 SHORT HANDWHEEL 1
9 M6 x 15mm HEX SCREW 3
10 M5 x 5mm GRUB SCREW 2
11 M6 x 8mm HEX SCREW 5
12 M10 E-RING 1
13 M10 METAL WASHER 2
14 M10 NUT 1
15 GROMMET PLATE 1
16 LONG HANDWHEEL 1
17 CABLE CLIP 1
18 CIRCULAR FOAM PAD 2
19 RECTANGULAR FOAM PAD 2
20 FLAT PLASTIC CAP 1
21 ANGLED PLASTIC CAP 1
22 M6 x 10mm SCREW 2
23 M6 METAL W ASHER 2
24 CABLE TIE 5
25 2.5mm HEX KEY (FOR PART10) 1
26 4mm HEX KEY (FOR PARTS 9 & 11) 1
A M4 x 12mm SCREW 4
B M4 x 30mm SCREW 4
C M5 x 12mm SCREW 4
D M5 x 30mm SCREW 4
E M5 x 20mm SPACER 4
INTERFACE KIT
A
B
C
D
25
26
PLEASE KEEP THIS FOR FUTURE REFERENCE
E
5
INSTALLATION INSTRUCTIONS
Choose a preferred mounting method.
i. Clamp (page 6)
ii. Grommet (page 8)
1
i. Desk clamp option.
4
11
18
12
6
13
5
19
Max 70mm
(2.8")
11
7
6
8
Attach the foam pads to the underside of the clamp base.
18
19
Place the mount over edge of the desk and tighten the short handwheel.
4
DESKTOP
6
8
7
ii. Grommet Clamp
4
15
11
18
8
19
6
14
13
16
Max 95mm
(3.7")
Remove the desk clamp and attach the grommet plate. Then attach the foam
pads onto the grommet plate.
26
11
4
Place the mount over the cable management hole and screw the handwheel into
the grommet plate, then tighten the nut to clamp the desk.
4
DESKTOP
26
11
15
5
4
19
18
16
14
16
9
2
Attach the interface plate to the flat screen.
2
DCBA
P
O
T
BO
M
O
T
T
1
FLAT
SCREEN
E
3
To lock the adjustment collar, hold the top of the collar and rotate the lower
part of the adjustment collar.
3
LOCK COLLAR
4
10
4
i.
Slide the flat screen and arms onto the pole, adjust height, then tighten the
grub screw.
2
FLAT
SCREEN
3
UNLOCK COLLAR
ii.
3
4
LOCK COLLAR
3
iii.
10
25
11
5
Insert the cable into the cable management slots on the underside of the
arms.
OPTIONAL : Cable Management.
WARNING:
Ensure articulating arms
are fully extended before
connecting cables.
2
CABLE
2
2
FLAT
SCREEN
2
4
17
CABLE
12
CABLE
CAUTION: Ensure there is adequate cable slack for movement of the
screen, and that cables will not be pinched when the mount is closed.
6
To increase tilt resistance, tighten part 9.
+/-40°
26
9
If this does not hold
the screen at the
required tilt, remove
the flat screen from
the interface.
Then remove plastic
nut cover and tighten
the M8 nyloc nut.
13
7
Tilt and swivel.
10
25
360°
10
25
360°
14
26
9
360°
+/-90°
26
9
BT7373
PRODUCT DIMENSIONS
457mm
18"MAX
478mm
18.8"MAX
243mm
35mm
O
1.4"
9.6"MIN
325mm
12.8"
476.7mm
18.8"
59mm
2.3"MIN
DESK CLAMP, GROMMET & BASE
169mm
6.7"
30mm
1.2"
110mm
4.3"
72mm
2.8"
95mm
3.7"
83.7mm
3.3"
70mm
2.8"MAX
95mm
218mm
8.6"
INTERFACE PLATE
100mm
3.9"
75mm
3"
75mm
3.9"
3"
120mm
4.7"
120mm
4.7"
100mm
3.7"MAX
THESE INSTRUCTIONS ARE INTEND ED AS A GUIDE ONLY AND B-TECH ACCEPTS NO
LIABILITY FOR THE ACCURACY OF THE I NFORMATION CONTAINED IN THIS DOCUMEN T.
15
www.btechavmounts.com
A
A
A
B-TECH AUDIO VIDEO MOUNTS
Bennett House, Long March, Daventry, Northants NN11 4NR, UK
EUROPE
Brixtonlaan 32, Zaventem 1930,
Brussels, Belgium
Email: info@btechproav.com
Buffalo, NY 14215, USA
Email: info@btechavmounts.com
Email: info@btechavmoun ts.co. uk
NORTH AMERIC
203 Eggert Road,
©2010 Bennett Technologies Limited. All rights reserved.
B-Tech Audio Video Mounts is a division of Bennett Technologies Limited.
B-Tech & Better By Design are registered trademarks of Bennett Technologies Limited.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
IP-BT7373-V1-PROBX-160810-21 MADE IN CHINA
HEAD OFFICE
SIA PACIFIC
Ruby Industrial Complex,
Singapore 347740
Email: info@btechavmounts.com.sg
CHIN
1503 Prosperity Millennia Plaza,
Quarry Bay, Hong Kong
Email: info@btechavmoun ts.com.hk
Loading...