Savio FP
Savio FP
USER MANUAL AND INSTRUCTIONS
WALL HUNG GAS BOILER FOR
CENTRAL HEATING SUPPLY
Please Read Instructions Carefully
Save for Future Reference
Do not store or use gasoline or other fl ammable vapors and liquids —
in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS —
Do not try to light any appliance.•
Do not touch any electric switch; do not use any phone in your •
building.
Immediately call your gas supplier from a neighbor’s phone. Fol-•
low the gas supplier’s instructions.
If you can not reach your gas supplier call the fi re department.•
Installation and service must be performed by a qualifi ed installer, —
service agency or the gas supplier.
WARNING: If the information in this manual is not followed
exactly, a fi re or explosion may result causing property dam-
age, personal injury or loss of life.
SAVIO FP USER MANUAL
2 SAVIO FP USER MANUAL
Dear Customer:
Thank you for buying a SAVIO FP Boiler System.
The SAVIO FP is a high effi ciency, non-condensing, wall mounted gas boiler which
provides central heat and domestic hot water.
We realize that it is not possible to answer all questions about the SAVIO boiler system in this
manual. Reading this installation manual does not make the reader an expert in all aspects
of installation and operation, and does not replace the need for a qualifi ed, licensed heating
contractor. We urge you to contact your installing contractor or distributor if you are in question
about any aspect of your boiler’s performance. Our main concern is that you are satisfi ed with
your boiler and its performance. We require that your contractor complete effi ciency tests using
instruments.
The external controls and accessories listed in this manual (excluding those supplied inside
the boiler) are intended to serve as guidelines rather than specifi c recommendations. We re-
alize that other makes and models of such devices are available and can be used as successfully as those we specify. The installing contractor is the best judge of a system’s specifi c
requirements, as well as the local availability of certain makes and models of controls and
accessories. The preceding does not apply, however, to the equipment that comes with every
boiler, such as the overheat control and pressure relief valves. The installation of the spe-
cifi c devices supplied with every boiler is absolutely necessary to the safe operation of
the boiler and protection of the heating system.
All SAVIO wall hung boilers are built in accordance with the ASME boiler and pressure vessel
code, and bear the “H” stamp. The Entire range of applications for the SAVIO FP has been
tested to standard CSA 4.9 and is CSA compliant.
This SAVIO boiler has a 2 year warranty on the boiler, and 10 years on the heat exchanger, a
copy of which is provided with the boiler. Please be sure to return the warranty registration card
as the warranty will be void without your boiler’s serial numbers (located on the ratings label
affi xed to the boiler), date of installation and the name of your installer being on record in our fi les.
Thank you for purchasing our SAVIO FP boiler. If you have questions or comments,
please don’t hesitate to contact us immediately. Our goal is 100% customer satisfaction.
BOYERTOWN
SAVIO FP USER MANUAL 3
Table of Contents
Section Title Section Number Page Number
Warnings - 4-5
Important Information - 6
General Information 1 7
Technical Information 2 7-8
Appliance Description 3 9
Operation Lights 4 10
Instructions for Use 5 11-14
Warnings 5.1 11
Refi lling Procedure 5.2 11
Lighting/Operation Instruction 5.3 12
Central Heating Circuit Temp. 5.4 12-13
Extinguishing Instructions 5.5 13
Domestic hot water 5.6 14
Useful Advice 6 15-17
Central Heating 6.1 15
Frost Protection 6.2 15
Periodic Maintenance 6.3 15
External Cleaning 6.4 16
Operational Faults 6.5 16-17
Warranty 18
4 SAVIO FP USER MANUAL
WARNING
DANGER
Boiler is certifi ed as an indoor appliance. Do not install boiler outdoors or locate where it will
be exposed to freezing temperatures.
Caution: Do not store or use fl ammable materials, chemicals or fl ammable liquids,
especially gasoline, in the vicinity of this heating appliance.
Caution: Should overheating occur or the gas supply fail to shut off, do not turn
off or disconnect the electrical supply to the pump. Instead, shut off the gas
supply at a location external to the appliance.
Caution: Do not use this boiler if any part has been under water. Immediately
call a qualifi ed service technician to inspect the boiler and to replace any part of
the control system and any gas control which has been under water.
Do not store or use gasoline or other fl ammable vapors and liquids in the —
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS —
Do not try to light any appliance.•
Do not touch any electric switch; do not use any phone in your build-•
ing.
Immediately call your gas supplier from a neighbor’s phone. Follow the •
gas supplier’s instructions.
If you can not reach your gas supplier call the fi re department.•
Installation and service must be performed by a qualifi ed installer, ser- —
vice agency or the gas supplier.
WARNING: If the information in this manual is not followed
exactly, a fi re or explosion may result causing property dam-
age, personal injury or loss of life.
SAVIO FP USER MANUAL 5
WARNING
Any appliance that burns natural gas, propane gas, fuel oil, wood or coal is capable of producing carbon monoxide (CO). Carbon Monoxide (CO) is a gas which is odorless, colorless
and tasteless but is very toxic. CO is lighter than air and thus may travel throughout the
building.
BRIEF EXPOSURE TO HIGH CONCENTRATIONS OF CO, OR
PROLONGED EXPOSURE TO LESSER AMOUNTS OF CO MAY
RESULT IN CARBON MONOXIDE POISONING. EXPOSURE CAN BE
FATAL AND EXPOSURE TO HIGH CONCENTRATIONS MAY RESULT
IN THE SUDDEN ONSET OF SYMPTOMS INCLUDING UNCONSCIOUSNESS.
Symptoms of CO poisoning include the following:
dizziness vision problems shortness of breath
headache loss of muscle control unclear thinking
nausea weakness unconsciousness
The symptoms of CO poisoning are often confused with those of infl uenza, and the highest
incidence of poisoning occurs at the onset of cold weather or during fl u season.
A victim may not experience any symptoms, only one symptom, or a few symptoms.
Suspect the presence of carbon monoxide if symptoms tend to disappear when you
leave your home.
The following signs may indicate the presence of carbon monoxide:
Hot gasses from appliance, venting system pipes or chimney, escaping into the living •
space.
Flames coming out around the appliance.•
Yellow colored fl ames in the appliance.•
Stale or smelly air.•
The presence of soot or carbon in or around the appliance.•
Very high unexplained humidity inside the building.•
If any of the symptoms of CO occur, or if any of the signs of carbon monoxide are present,
VACATE THE PREMISES IMMEDIATELY AND CONTACT A QUALIFIED HEATING SERVICE COMPANY OR THE GAS COMPANY OR THE FIRE DEPARTMENT.
ONLY QUALIFIED, LICENSED SERVICE CONTRACTORS SHOULD PERFORM WORK
ON YOUR SAVIO FP.
6 SAVIO FP USER MANUAL
IMPORTANT INFORMATION
Please read this page carefully.
ALL BOILERS MUST BE INSTALLED IN ACCORDANCE WITH NATIONAL, •
STATE AND LOCAL PLUMBING, HEATING AND ELECTRICAL CODES
AND ORDINANCES, AS WELL AS THE REGULATIONS OF THE SERVING
ELECTRICAL, WATER AND GAS UTILITIES.
All systems should be designed by competent contractors, and only persons •
knowledgeable in the layout and installation of heating systems should attempt
the installation of any boiler. It is the responsibility of the installing contractor
to see that all controls are correctly installed and operating properly when the
installation is completed.
This boiler is intended for use, only with propane or natural gas. All fl ammable •
liquids (especially gasoline), chemicals, rags, paper, wood scraps, debris, etc.,
should be kept away from the boiler at all times. Keep the boiler area clean and
free of all fi re hazards.
Please read the literature and warranties supplied by the manufacturers of the •
various accessory equipment. This equipment is warranted by the respective
manufacturers, not by BOYERTOWN. Each piece of equipment must be
installed and used according to the recommendations of the manufacturer.
Codes and Regulations:
Installation of the boiler and related equipment must conform to national, state and
local regulating agencies and codes applicable to the installation of the equipment. In
the absence of local requirements, the following codes apply:
A. ANSI/NFPA - #70 National Electric Code
B. ANSI/NFPA - #211 Chimneys and Vents
C. ANSI/NFPA - #Z223.1 National Fuel Gas Code
C. ANSI/NFPA - Domestic Gas Conversion Burner
D. CAN/CGA - B149 Installation Codes
E. ANSI/ASME - CSD-1
The above codes are available from:
National Fire Protection Association (NFPA) CSA International
Battery March Park 8501 E. Pleasant Valley Road
Quincy, Massachusetts, 02269 Cleveland, OH 44134-5575
http://www.nfpa.org http://www.csa-international.org
SAVIO FP USER MANUAL 7
General Information1.
Technical Information (M130.30CM)2.
The SAVIO FP is a high effi ciency, non-condensing, wall mounted gas boiler which pro-
vides central heat. The boiler features a gas valve which modulates the energy input from
49,476BTU/h to 122,837 BTU/h. The boiler is shipped fully assembled. All units are pressure
and combustion tested at the factory prior to shipping.
Key Features:
Wall mountable - saving valuable fl oor •
space.
Several fl ue options available•
Electronic spark ignition•
Safety fl ow switch - positioned on the •
main circuit, which monitors the fl ow and
protects the main heat exchanger from
thermal shock should there be a lack of
water in the system.
Frost protection - contains an integral frost •
protection system to prevent frost damage which can occur in areas susceptible
to very cold weather conditions.
Boiler operation recognition system - •
should the boiler not be used for longer
than 24 hours, it then performs a controlled system test to ensuring the motorized components within the boiler do not
become inoperable due to lack of use.
Gas valve modulation - the gas input •
modulates based off central heating temperature to within ± 2 ºF
Diagnostic information system equipped •
with three LED diagnostic lights for quick
error assessment.
GENERAL
Height in 27.7
Width in 15.7
Depth in 12.8
Weight lb 78.7
ELECTRICAL
Voltage V 120
Frequency Hz 60
Current A 1.6
Power consumption W 180
INJECTORS No. Size
Natural 14 130
Propane 14 89
CENTRAL HEATING
Maximum working temp. °F 185
Temp. Regulation range* °F 100-176
Maximum pressure psi 30.0
Minimum pressure psi 4.35
Max head loss (at 4.4 GPM) ft 9.9
*At the minimum useful output
8 SAVIO FP USER MANUAL
2. Technical Information Cont.
ENERGY CAPACITY
Nominal heat input
(0/2000ft)
MBH 122.8
Nominal heat input
(2000/4500ft)
MBH 116.7
Minimum heat input MBH 49.5
Maximum useful output
(0/2000ft)
MBH 100.7
Maximum useful output
(2000/4500ft)
MBH 95.9
Minimum useful output MBH 37.0
GAS SUPPLY PRESSURE
Gas Normal Min Max
Natural inwc 7.0 3.5 10.5
Propane inwc 11.0 8.0 13.0
GAS PRESSURE AT BURNER
Gas Min Max Ignition
Natural inwc 0.8 5.3 2.4
Propane inwc 1.4 9.0 5.2
FLUE DESIGN
Minimum Venturi pressure inwc 0.66
Flue pipe diameter
Coaxial in
2.25/4
3.25/5
Twin split pipes in 3.25/3.25
Nominal heat fl ow rate
(0/2000ft)
MBH 122.8
Nominal heat fl ow rate
(2000/4500ft)
MBH 116.7
Min Exhaust temperature °F 262
Max Exhaust temperature °F 324
GAS FLOW RATE
Gas Min Max
Natural ft³/h 48.7 121.1
Propane lb/h 2.2 5.6
CLEARANCE TO COMBUSTIBLES
Front in 18
Back in 0
To p i n 8
Sides in 2
Bottom in 8
Flue pipe enclosed in 2
Flue pipe free air in 0
Hot water pipes in 1”
FLUE GAS FIGURES
Gas Min Max
CO2
2.5% 7.2%
O2
16.5% 8.1%
DOMESTIC HOT WATER
Maximum temperature °F 131
Minimum temperature
°F 95
Maximum pressure
psi 145
Minimum pressure psi 4.35
D.h.w. ΔT 25K gpm 4.5
D.h.w. ΔT 30 K gpm 3.7
D.h.w. ΔT 35 K gpm 3.2
D.h.w. ΔT 40 K gpm 2.8
SAVIO FP USER MANUAL 9
Appliance Description3.
Overview:3.1
1 Case front panel
2 Control panel
3 Control panel cover
Control Panel:3.2
4 Central heating circuit temperature and
pressure gauge
5 Lock-out signal lamp
6 Boiler reset button
7 Function selector knob and radiator
temperature control
8 Domestic hot water, temperature
control knob
9 Appliance operation lights
3 1 2
98 7 65 4
Piping Connections:3.3
A Gas inlet pipe
B Main circuit drain cock
C C.h. supply copper pipe
D C.h. return copper pipe
E C.h PRV discharge copper pipe
F D.h.w. hot water outlet
G D.h.w. cold water inlet
Figure 3.1
Figure 3.2
Figure 3.3
10 SAVIO FP USER MANUAL
Operation Lights4.
Three lights (8 in Fig. 3.2) give detailed indication regarding the operation of the boiler.
The following table gives the relationship between each of the possible light combinations and
their meaning.
A short pulse every 4 seconds: stand-by condition Function
selector in
position. Anti-freeze system active
1 second pulse every 2 seconds: normally operating boiler.
Function selector in on position
Central heating operation
Frost protect operation
Faulty central heating temperature probe NTC
Faulty primary circuit (no water or absence of fl ow)
Lack of burner ignition (no ignition signal from the full sequence ignition device)
Ignition gas pressure adjustment
Minimum gas pressure adjustment
Lamp OFF Lamp ON
Flashing lamp, alone
or simultaneously
with another lamp.
Flashing lamp, alternate with another
lamp
SAVIO FP USER MANUAL 11
Instructions For Use5.
Warnings:5.1
In order to guarantee safety and correct operation, it is essential that all the tests are carried •
out by a competent and responsible licensed service person before lighting up the boiler.
The tests are described in the installation, operation and service instructions manual in Sec-•
tion 15 Commissioning.
Ensure that the Central Heating circuit is regularly fi lled with water checking that the pres-•
sure indicated on the temperature and pressure gauge (4 on fi gure 3.2) is not lower than 1
bar (14.5 psi) as shown on fi gure 5.1.
If the pressure reading on the pressure gauge is below 1 bar (14.5 psi), then the system •
will require fi lling. An automatic fi lling valve is normally provided by the installer for this pur-
pose.
If you are in any doubt regarding this procedure you are advised to contact your In-•
staller or an Approved Service Person.
This appliance is provided with a built in anti-freeze system that operates the boiler when •
the temperature is below 41 °F
Therefore, when the boiler is not lit or used in cold weather, with consequent risk of freezing •
do not switch off the boiler at the circuit breaker or close the gas inlet cock.
When you expect not to use the boiler for a long period follow the instructions given in sec-•
tion 5.6 on page 14.
Refi lling procedure:5.2
Isolate the boiler from the electrical sup-•
ply at the circuit breaker.
The boiler should have been installed with •
an automatic fi ll valve, external to the unit.
Open the cold water supply to the automatic fi ll valve.
The pressure should be 1 – 1,5 bar (14.5 •
– 22 psi).
The automatic fi ll valve should maintain •
this pressure, but not exceed it.
Figure 5.1
0
4
2
3
1
Air introduced into the boiler during this fi lling process will vent through the automatic air purger
fi tted to the boiler. You may also fi nd it necessary to vent air from your heating circuit using the
installed vents, however be aware that excessive venting will cause the pressure in the system
to drop. Always ensure that the pressure gauge is set at the required pressure.
12 SAVIO FP USER MANUAL
5. Instructions For Use Cont.
Lighting/Operating Instructions:5.3
Warnings: Do not attempt to start the boiler unless all cleanout doors are secured and
sealed. Do not attempt to light the burner by hand.
1 Check that the cocks connected to the
gas inlet pipe and to the supply cold water inlet pipe (see section 3.3 for pipes)
are open.
2 Turn on the electricity supply to the boiler,
switching on the circuit breaker. The appliance operation light A (fi gure 5.2) will fl ash
every 4 seconds (stand-by condition).
Figure 5.2
A B C D E
3 If the boiler is to be used for c.h position
the function selector C as in fi gure 5.2.
The appliance operation light A will fl ash
every 2 seconds (operating boiler).
4 If the appliance will not operate, follow
the extinguishing instructions on page 13
and call your service technician or gas
supplier.
Central Heating Circuit Temperature:5.4
1 The output temperature of c.h. water is
adjustable from a minimum of about 100
°F to a maximum of about 176 °F (Figure
5.3), by turning the knob B
2 Adjustment of the boiler temperature al-
ters the gas fl ow at the burner according
to the thermal demand in the system. So
it is usual to see the burner lit at the minimum level for more or less long periods.
3 Adjustment of central heating. output on
the boiler is automatic. The greatest output is factory pre-set, however, it can be
reduced according to actual system requirements. These adjustments must be
carried out by a qualifi ed person; there-
fore we advise you to contact your installer or Service Agent.
Figure 5.3
SAVIO FP USER MANUAL 13
5. Instructions For Use Cont.
Adjustment:
In order to achieve optimal settings for •
economy and comfort, we recommend
adjusting the operating temperature of
the central heating water according to the
outside temperature, positioning the knob
as in fi gure 5.4
Your installer may have installed addi-•
tional energy saving equipment and will
be able to recommend the most suitable
adjustment for your system.
The temperature and pressure gauge (Fig. •
5.1 on page 11) will allow you to check
that the set temperature is obtained.
Figure 5.4
From 41 to 59°F
Lower than 23°F
Between 23 and 41°F
Extinguishing Instructions:5.5
To turn the boiler off set the function se-•
lector C to the position shown in the Figure 5.5.
The appliance operation light A (fi gure5.2) •
will fl ash every 4 seconds (stand-by
mode).
Turn off electric power to the appliance •
at the circuit panel of boiler serviceman’s
switch.
Figure 5.5
AC
When you expect not to use the boiler for a long period:
Switch off the electricity supply to the boiler, by means of the circuit breaker;•
Shut off the gas supply cock connected to the gas inlet pipe and the cock connected to the •
supply cold water inlet pipe (see section 3.3 for pipes)
Empty the water circuit, if necessary, as shown in the installation, operation and service •
instructions manual in the maintenance section.
14 SAVIO FP USER MANUAL
5. Instructions For Use Cont.
Domestic hot water temperature:5.6
The temperature of the domestic hot water coming out from the boiler can be regulated from a
minimum of approximately 95° F to a maximum of approximately 131° F by turning the control
shown in fi g. 5.6
Figure 5.6
Minimum
Maximum
Figure 5.7
Adjustment of the d.h.w. temperature is completely separate from that of the c.h. circuit.
The adjustment system integrated within the boiler automatically controls the fl ow of gas to
the burner in order to keep the temperature of d.h.w. delivered constant, between the limits of
maximum and minimum output.
Where the demand is at a low level or with the temperature set to the minimum,it is normal to
see a cycle of lighting and extinguishing of the burner when running.
Regulate the domestic hot water temperature to a value suitable for your requirements.
Reduce the need to mix the hot water with cold water.
In this way, you will appreciate the characteristics of automatic regulation.
If the water is particularly hard, we recommend regulating the boiler at a temperature lower
than 120° F fi g.
In these cases, we nevertheless recommend the installation of a water-softener on the domestic hot water system.
If the maximum fl ow rate of the domestic hot water is too high for a suffi cient temperature to be
reached, it is advisable to have a suitable fl ow rate limiter installed by an Authorised Assistance
Technician.
SAVIO FP USER MANUAL 15
Useful Advice6.
Central Heating:6.1
For reasonably economical service install •
a room thermostat.
Never shut off the radiator in the area •
where the room thermostat is installed.
If a radiator (or a convector) does not heat •
up, check that no air is present in it and
that its valve is open.
If the ambient temperature is too high, do •
not alter the radiator valves. Reduce the
central heating temperature instead by
means of the room thermostat and the
knob (C in Fig. 6.1).
Figure 6.1
C
Frost Protection:6.2
The built in antifreeze system and any additional system protect the boiler from possible •
damages due to the icing.
This system doesn’t guarantee the protection of the whole central heating system.•
In the case that the external temperature may be lower than 32°F it is suggested to leave •
the system running setting the room thermostat at a low temperature.
When the boiler is completely switched off for a long period, it is recommended to empty •
completely central heating circuit.
Periodic Maintenance:6.3
For effi cient and continuous operation of the boiler, it is advisable to arrange maintenance •
and cleaning by an Authorised Service Person, at least once a year.
During the service, the most important components of the boiler will be inspected and •
cleaned. This service can be part of a maintenance contract.
In particular, you are advised to have the following checks carried out:
primary heat exchanger;•
burner;•
exhaust fume duct and fl ue;•
pressurization of the expansion vessel;•
fi lling up of the central heating circuit;•
bleeding of air from the central heating system;•
general check of the appliance’s operation.•
16 SAVIO FP USER MANUAL
6. Useful Advice Cont.
External Cleaning:6.4
Before performing any cleaning, disconnect the appliance from the electrical mains, using •
the dedicated circuit breaker or serviceman’s switch located adjacent to the appliance.
To clean the external panels, use a cloth soaked in soapy water. Do not use solvents, abra-•
sive powders or sponges.
Do not carry out cleaning of the appliance and/or its parts with readily fl ammable substanc-•
es (for example petrol, alcohols, naphtha, etc.).
Operational Faults:6.5
If the lock-out signal lamp comes on:
This indicates that the safety lock-out 1 •
(Fig. 6.2) has stopped the boiler
To re-start the boiler, it is necessary to •
turn the function selector B in the position
and then press the boiler reset button
2 (Fig. 6.2).
For the fi rst light up and following main-•
tenance procedures for the gas supply, it
may be necessary to repeat the resetting
operation several times so as to remove
the air present in the pipework.
Figure 6.2
AC
If noises due to air bubbles are heard during operation:
You should check that the pressure on the temperature and pressure gauge (Fig. 5.1 on •
page 11) is not below the correct setting.
If required, fi ll up the system correctly, as described in the section 5.2 of this manual.•
Bleed any air present in the radiators, if necessary.•
If the pressure on the temperature and pressure gauge (Figure 5.1 on page 9) has
gone down:
It is necessary to fi ll up the appliance with water again, so as to raise the pressure to an •
adequate level as described in the section 5.2 of this manual.
If fi lling up with water has to be done very frequent, have the system checked for leaks.•
SAVIO FP USER MANUAL 17
6. Useful Advice Cont.
If water comes out of the pressure relief valve pipe 3 in Fig. 6.3:
Check on the temperature and pressure •
gauge (fi gure 5.1 on page 11) that the
pressure in the central heating circuit is
not close to 3 bars (43.5 psi). In this case,
temperature rise in the circuit can cause
the pressure relief valve to open.
So that this does not happen and to de-•
crease the pressure to a normal value, it
is advisable to vent some of the water in
the appliance through the bleed valves
present in the heating system.
Figure 6.3
If water should occasionally leak from the boiler:
Close the cocks connected to the inlet gas pipe and to the supply cold water inlet pipe under •
the boiler and call an Authorised Service Person.
In case of problems other than those mentioned here, switch off the boiler, as described
in Section 5.5 on page 13 and call a competent and responsible service person.
18 SAVIO FP USER MANUAL
Warranty
For SAVIO Residential
Wall Hung Gas Boilers
FIRST 2 YEARS-WARRANTY FOR SAVIO SERIES
RESIDENTIAL HOT WATER BOILERS: BOYERTOWN
warrants that itswall hung boiler and casing are free
from defects in material and workmanship for 2 years
from the date of installation. If any part on the boiler is
found to be defective within this period, BOYERTOWN
will replace the part free of charge.
FIRST 10 YEARS-WARRANTY FOR SAVIO SERIES
RESIDENTIAL HOT WATER BOILERS: SAVIO warrants that the copper tube heat exchanger of the SAVIO
boilers are free from defects in material and workmanship for 5 years from the date of installation. If the copper tube heat exchanger is found to be defective within
the fi rst 5 years after installation, BOYERTOWN and
SAVIO will replace the copper tube heat exchanger.
These warranties are subject to the condition that a
heating contractor whose principal occupation is the
sale and installation of heating equipment must have
installed the boiler. PARTS, WHICH ARE COVERED,
consists of all materials supplied by SAVIO, identifi ed
by BOYERTOWN’s part numbers in its literature. Other
parts supplied by the installer carry their own warranty
and each manufacturer has responsibility for its own
products.
NOTE: ANY PART, WHICH IS REPLACED UNDER
WARRANTY, CARRIES ONLY THE UNEXPIRED
PORTION OF THE ORIGINAL WARRANTY.
OWNER RESPONSIBILITIES:
1. Provide for proper installation, which includes pressure relief and pressure reducing valves and high limit
safety controls on closed systems.
2. Provide qualifi ed periodic service to prolong proper
operation and service.
3. Insure that boiler is installed in accordance with all
codes and ordinances.
4. This warranty does not apply to boilers, which are
subject to misuse, abuse, neglect, alteration, accident,
excessive temperature, excessive pressure, or corrosive water or atmosphere.
5. Owner will be responsible for return of faulty components to BOYERTOWN, PA, freight pre-paid.
BOYERTOWN and SAVIO will not be responsible for:
1. Components that are part of the heating system, but
were not manufactured by SAVIO or BOYERTOWN as
part of the boiler.
2. The workmanship of the installers of SAVIO boilers.
Furthermore, this warranty does not assume any liability for unsatisfactory performance caused by improper
installation.
3. Any costs for labor to remove or replace the faulty
component.
4. Improper boiler application or adjustments, control
settings, care or maintenance.
5. Any damage associated with corrosion or leakage
due to the use of “non-barrier”, plastic pipe in the heating system.
*IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY
SHALL BE LIMITED TO THE DURATION OF THE
EXPRESSED WARRANTY. SAVIO AND BOYERTOWN EXPRESSLY DISCLAIM AND EXCLUDE ANY
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF ANY EXPRESSED OR
IMPLIED WARRANTY.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE.
For prompt warranty service, notify the installer, who,
in turn, will notify the distributor from whom the boiler
was purchased. If this does not result in corrective action, contact SAVIO through BOYERTOWN Hydronic
Technologies (Address Below) with details in support
of the warranty claim. All claims must be processed
through proper trade channels. Contact with SAVIO directly is not recommended for rapid claim settlement.
BOYERTOWN Furnace Co.
PO Box 100
Boyertown,PA 19512
1-610-369-1450
www.boyertownfurnace.com
SAVIO BOILER WARRANTY REGISTRATION
IMPORTANT., Registration required. To gain complete warranty
Protection, fi ll in and mail this card, within 1 year of installation to the address listed below
NAME:____________________________________ ADDRESS:____________________________
CITY:______________________ STATE:________ ZIP:______________
BOILER SERIAL NO.: _______________________ DATE OF INSTALL:_____________________
NAME OF INSTALL CO.:_____________________ ADDRESS:____________________________
CITY:______________________ STATE:________ ZIP:____________
RETURN TO: BOYERTOWN FURNACE Co. PO Box 100 BOYERTOWN PA 19512 1-610-369-1450
SAVIO FP USER MANUAL 19
17962.1512.0 2908 (20A4)USA
17/07
2008
N
Loading...