Bryston BryFi Quick Start Manual
Quick Start Guide
1 2 3 4 5 6
7
8 9
Geing Started
Before you begin, please make sure that you have the following available:
A computer network with 2.4GHz WiFi or Ethernet
One of the following devices:
An Apple® iPhone®, iPod®, or iPad® running iOS 7 or greater
An Android smartphone or tablet running version 4.0 or greater
A PC with WiFi adapter running Windows 7 or greater
A Mac® computer with AirPort® card running OS X® 10.7 or greater
Controls and Connections
1. Power buon: To turn on the BryFi press and release the power buon. To turn o the system, press the power
buon briey and the BryFi will safely shutdown in about 20 seconds. If the system should become unresponsive for
any reason, simply press and hold the power buon until the green LED turns o. (is can take over 30 seconds.)
2. Analog input: An external playback device with a line or headphone output can be connected to the BryFi system
using this 3.5mm stereo input jack. To select the analog input, click on the gear icon in the top right corner of the web
interface and click the check box beside analog input.
3. Analog volume control: Use this control to adjust the volume of an external analog source. Note that this control will
not function with digital le playback via AirPlay, UPnP, or local digital music les.
4. Status Lights: See page 2 for a full description of the status light indicators.
5. USB ports: Can be used to aach external USB thumb drives for music playback. Note that one USB port is
populated with a WiFi adapter. Do not remove or change the location of this device.
6. Ethernet port: Can be used to connect to a wired LAN.
7. Power Input: Plug the round connector from the supplied power brick into this jack . e at side should be facing
up.
8. Sub Out: 3.5mm output jack to connect an external subwoofer. A 3.5mm to RCA cable may be necessary depending
on subwoofer.
9. Analog input: An external playback device with a line or headphone output can be connected to the BryFi system
using this 3.5mm stereo input jack. To select the analog input, click on the gear icon in the top right corner of the web
interface and click the check box beside analog input.
1
Status Lights
Lights Status/Description
None BryFi is o
Solid Green BryFi is on
Flashing Blue (slow) BryFi is in hotspot mode
Flashing Blue (fast) BryFi is in hotspot mode and is in WiFi accessory conguration mode
Solid Blue BryFi is connected to local WiFi / wired network
Flashing Red BryFi is out of range of local network / conguration error
Solid Red BryFi baery needs charging (if equipped)
Connect to Power
Place your BryFi in a location where you’d like to enjoy your music.
Align the round connector from the supplied power brick to the jack marked 15VDC IN on the back of your BryFi by keeping the
at side of the connector facing up before inserting fully.
Plug the supplied power cable into the power brick and then into a nearby wall outlet.
Optional: If you are connecting to a wired network, ip down the door at the boom ont of the BryFi and plug in an Ethernet
cable. Do not connect an Ethernet cable if you’d like to connect your BryFi to a wireless network.
Flip down the door at the boom front of the BryFi and press the white buon. You should see a green LED illuminate.
In approximately 45 seconds you will hear a xylophone start-up sound, followed by a ashing blue LED, indicating that the system is
in hotspot mode and ready to be added to your home WiFi network.
Find the Section in the following pages for your device type
Section 1 – iOS devices
Section 2 – Android Devices
Section 3 – Windows PC
Section 4 – Mac computer
2
Turn On
Connect to WiFi
Loading...