Bryant SYSTXBBRWF01 User Manual

SYSTXBBRWF01 EVOLUTIONr SYSTEM WiFi (WIRELESS) BROADBAND REMOTE ACCESS MODULE

Installation Instructions

NOTE: Read the entire instruction manual before starting the

installation.

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may cause death, personal injury or property damage. Consult a qualified installer, service agency or your distributor or branch for information or assistance. The qualified installer or agency must use factory--authorized kits or accessories when modifying this product. Refer to the individual instructions packaged with the kits or accessories when installing.

Follow all safety codes. Wear safety glasses, protective clothing, and work gloves. Have a fire extinguisher available. Read these instructions thoroughly and follow all warnings and cautions included in literature and a ttached to the unit. Consult local building codes and the current edition of the National Electrical Code (NEC) NFPA 70.

In Canada, refer to the current editions of the Canadian Electrical Code CSA C22.1.

Recognize safety information. When you see this symbol the unit and in instructions or manuals, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING,andCAUTION. These words are used with the safety--alert symbol. DANGER identifies the most serious hazards, which will result in severe personal injury or death. WARNING signifies hazards, which could result in personal injury or death. CAUTION is used to identify unsafe practices, which may result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation.

INSTALLATION CONSIDERAT IONS

The WiFi Broadband Wireless Remote Access Module (WiFi B--SAM), part number SYSTXBBRWF01, is powered with a 24VAC transformer which is included. A 120VAC supply must be near the mounting location. Provisions must be made to secure the transformer to the outlet. The D--wire (24VAC) from the

Evolutionr system must NOT be used to power the Remote Access Module.

This instruction covers the physical installation and start up of WiFi B--SAM. Use this instruction to guide the actual installation process after the Evolution system(s) have been installed. One WiFi B--SAM is capable of handling two Evolution systems.

INTRODUCTION

The WiFi B--SAM connects to a network router and allows remote connectivity for up to two Evolution systems within the same building. The Evolution system owner, as well as authorized dealer, can monitor and control the system via the Internet, as well as by telephone. The WiFi B -- SAM communicates wirelessly through the homeowner’s cable or DSL Internet service. Broadband Internet service with a wireless network router is required. The WiFi B--SAM is not compatible with dial--up

Internet service. The WiFi B--SAM can also monitor a dry--contact sensor to provide a warning for the presence of water in the building, or some other use. If the sensor is active, the Evolution system will not be disabled or shut down.

Computer Requirements

The WiFi B-- SAM uses a web--based application to control and monitor the Evolution System. This application will work with any graphic user interface PC operating system (Microsoft, Apple, Linux). The web-- based application is optimized for use with Microsoft’s Internet Explorer version 6 and above. Other web browsers are compatible with some possible screen formatting issues.

WiFi INSTALLA TION

BEFORE STARTING:

S SYSTXBBUID01--B or SYSTXBBUIZ01--B is

required (version 14 software revision or higher).

S Retrieve your wireless network’s SSID (network

name) and encryption type and key (if used).

To get the SSID, right--click on the wireless network connection icon in the lower right corner of the desktop on a Windows--based PC that is connected to the wireless network:

Wireless Networks

A08408

From the pop--up menu, choose View Available Wireless Networks.

A08409

A window will open showing all of the wireless networks available:

SYSTXBBRWF01

SSID of a network, note the name of your network (including case of letters)

A08410

Encryption type and key will need to be obtained from your wireless router’s administration web page. Please see the instructions of your router to obtain this.

Note your network information here before installing the WiFi B--SAM.

SSID

Encryption Type:

Encryption Key:

1. Mount WiFi B--SAM and connect ABC wiring and 24VAC transformer.

2. Power up WiFi B--SAM and HVAC system and perform installation procedure from user interface.

Go to Installer Service menus (10 second press of Advanced) and select INSTALL.

Ensure “REMOTE ACCESS YES” appears on equipment summary screen (check ABC wiring if not).

3. Go to the WiFi B--SAM Setup screens by pressing the Advanced button on the user interface and then pressing the right side button until the WiFi B--SAM Setup screens appear. These screens will not appear if you do not have a --B model user interface.

4. Press the right side button to get to WiFi B-- SAM WIRELESS SETUP 1.

5. Highlight the SSID item and enter your network’s SSID (it is case sensitive).

Press the Temp Up/Down to move the cursor left or right.

Press the Time Up/Down to change the character.

The Space character is obtained by continuously pressing the Time Down button.

6. If you have encryption, press the right side button to go to WiFi B--SAM WIRELESS SETUP 2.

Select the encryption type. Enter the encryption key.

Press the Temp Up/Down to move the cursor left or right.

Press the Time Up/Down to change the character.

Encryption type and key will need to be obtained from your wireless router’s administration web page. Please see the instructions of your router to obtain this.

7. Exit the menus by pressing the Advanced button, saving all entries.

8. Give the system about 2 minutes to respond to all the changes.

9. The green LED light on the WiFi B--SAM wireless circuit board will flash if it is NOT connected. The LED will be lit solid if it is connected to your network.

10. If the LED is lit solid, give the system 15 minutes to transmit your equipment information to the server. Then, go to the web site and register your system by clicking on New User link. Enter your WiFi B--SAM’s serial number and MAC Address.

11. If the LED continues to blink, check your SSID and encryption entry for errors.

+ 4 hidden pages