Bryant 113A, Legacy 113A Product Data

113A LegacytRNC Line 13 Air Conditioner with Puronr Refrigerant 1--1/2 to 5 Nominal Tons (Sizes 018--060)

Product Data

the environmentally sound refrigerant

Bryant’s Air Conditioners with Puronr refrigerant provide a collection of featu res unmatch ed by any other family of equipment. The 113A has been designed utilizing Bryant’s Puron refrigerant. The environmentally sound refrigerant allows you to make a responsible decision in the protection of the earth’s ozone layer.

As an Energy Starr Partner, Bryant Heating and Cooling has determined that this product meets the Energy Starr guidelines for energy efficiency. Refer to the combination ratings in the Product Data for system combinations that meet Energy Starr guidelines.

NOTE: Ratings contained in this document are subject to change at any time. Always refer to the AHRI directory (www.ahridirectory.org) for the most up --to--date ratings information.

INDUSTRY LEADING FEATURES / BENEFITS

Efficiency

13 -- 14 SEER/10.55 -- 12 EER

S S Microtube Technologyt refrigeration system S Indoor air quality accessories available

Sound

Sound level as low as 75 dBA

S S Sound level as low as 74 dBA with accessory sound

blanket

Comfort

System supports Thermidistatt or standard thermostat

controls

Reliability

Puronr refrigerant -- environmentally sound, won’t

deplete the ozone layer and low lifetime servce cost.

S Scroll compressor S Internal pressure relief valve S Internal thermal overload S Filter drier S Balanced refrigeration system for maximum reliability

Durability

DuraGuardt protection package:

S Solid, durable sheet metal construction S Dense wire coil guard available S Baked--on, complete outer coverage, powder paint

Applications

Long-- line -- up to 250 feet (76.20 m) total equivalent

length, up to 200 feet (60.96 m) condenser above evaporator, or up to 80 ft. (24.38 m) evaporator above condenser (See Longline Guide for more information.)

S Low ambient (down to --20_F/--28.9_C)) with

accessory kit

MODEL NUMBER NOMENCLATURE

12 3 4 5 6789 1011 1214 N N N A A/N N N N N A/N A/N N A

11 3 A N A036 0 0 0 0

Product

Famil y

1=AC

Tier SEER

Legacy RNC

3=13 SEER A=Puron

Major

Series

Vol ta ge

N= 208---230 --- 1

or 208/230--- 1

Grille

Vari a ti on s

A=Dense

W=Standard

ISO 9001:2000

Cooling Capacity

Open Open Open Series

0=Not

Defined

0=Not

Defined

0=Not

Defined

the environmentally sound refrigerant

113A

REGISTERED

This product has been designed and manuf actured to meet Energy Star ® criteria f or energy efficiency when matched with appropriate coi l components. However, proper refri gerant charge and proper air fl ow are critical to achieve rated capacity and efficiency. Installation of this product should follow all manufacturing refrigerant charging and air flow instructions. Failure to confirm

proper ch arge and air flow may reduce energy efficiency and shorten equipment life.

STANDARD FEATURES

Feature 018 024 030 036 042 048 060

Puron Refrigerant X X X X X X X

Maximum SEER 14.5 14.5 14.5 14.0 14.0 14.5 13.5

Scroll Compressor X X X X X X X

FieldInstalledFilterDrier X X X X X X X

Front Seating Service Valves X X X X X X X

Internal Pressure Relief Valve X X X X X X X

Internal Thermal Overload X X X X X X X

Long Line capability X X X X X X X

Low Ambient capability with Kit X X X X X X X

X=Standard

PHYSICAL DATA

UNIT SIZE--- VOLTAGE, SERIES 018 --- D 024 --- D 030 --- E 036---E 042 --- C 048 --- E 060 --- G

Operating Weight lb (kg)

Shipping Weight lb (kg)

Compressor Type Scroll

REFRIGERANT Puron® (R --- 410A)

Control TXV (Puron® Hard Shutoff)

Charge lb (kg)

COND FAN Propeller Type, Direct Drive

Air Discharge Vertical

Air Qty (CFM) 1792 2218 2218 2954 3167 3365 3129

Motor HP 1/12 1/10 1/10 1/4 1/5 1/4 1/4

Motor RPM 1100 1100 1100 1100 1100 1100 800

COND COIL

Face Area (Sq ft) 8.4 8.4 9.80 13.13 17.25 19.40 12.93

Fins per In. 20 25 25 25 25 25 20

Rows 1 1 1 1 1 1 2

Circuits 3 3 3 3 4 5 5

VALVECONNECT.(In.ID)

Vapor 3/4 3/4 3/4 7/8 7/8 7/8 7/8

Liquid 3/8

REFRIGERANT TUBES (In. OD)

Rated Vapor* 3/4 3/4 3/4 7/8 7/8 7/8 1 --- 1 / 8

Max Liquid Line{ 3/8

* Units are rated with 25 ft (7.6 m) of lineset length. See Vapor Line Sizing and Cooling Capacity Loss table when using other sizes and lengths of lineset.

Note: See unit Installation Instruction for proper installation.

{ See Liquid Line Sizing For Cooling Only Systems with Puron Refrigerant tables.

107

(48.5)

130

(59.0)

3.50

(1.59)

110

(49.9)

134

(60.8)

3.80

(1.72)

111

(50.3)

136

(61.7)

4.10

(1.86)

141

(64.0)

170

(77.1)

5.34

(2.42)

189

(85.7)

217

(98.4)

5.84

(2.65)

186

(84.4)

224

(101.6)

7.00

(3.18)

190

(86.2)

226

(102.5)

8.19

(3.71)

113A

REFRIGERANT PIPING LENGTH L I M I TATIONS

Liquid Line Sizing and Maximum Total Equivalent Lengths

The maximum allowable length of a residential split system depends on the liquid line diameter and vertical separation between indoor and outdoor units.

See Table below for liquid line sizing and maximum lengths :

Maximum Total Equivalent Length Outdoor Unit BELOW Indoor Unit

Liquid

Size

18000

AC with

Puron

24000

AC with

Puron

30000

AC with

Puron

36000

AC with

113A

Puron 42000

AC with

Puron 48000

AC with

Puron 60000

AC with

Puron

* Maximum actual length not to exceed 200 ft (61 m) { Total equivalent length accounts for losses due to elbows or fitting. See the Long Line Guideline for details.

--- --- = o u t s i d e a c c e p t a b l e r a n g e

Liquid Line

Connection

3/8

3/8 3/8 250* 250* 250* 250* 250* 250* 230 160 --- ---

3/8 3/8 250* 250* 250* 225* 190 150 110 --- --- --- ---

Line

Diam.

w/ TXV

5/16 250* 250* 250* 250* 250* 250* 250* 225* 150

5/16 250* 250* 250* 250* 250* 225* 175 125 100

1/4 30 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --5/16 175 225* 200 175 125 100 75 --- --- --- ---

5/16 175 150 150 100 100 100 75 --- --- --- ---

3//8 250* 250* 250* 250* 250* 250* 250* 250* 250*

5/16 125 100 100 75 75 50 --- --- --- --- --- ---

(0---1.5)

1/4 150 150 125 100 100 75 --- --- --- --- --- ---

3/8 250* 250* 250* 250* 250* 250* 250* 250* 250* 1/4 75 75 75 50 50 --- --- --- --- --- --- --- ---

3/8 250* 250* 250* 250* 250* 250* 250* 250* 250*

3/8 250* 250* 250* 250* 250* 250* 250* 250* 150

AC with Puron Refrigerant Maximum Total Equivalent Length{: Outdoor unit BELOW Indoor

0 --- 5

6 --- 1 0

(1.8---3.0)

11---20

(3.4---6.1)

{

for Cooling Only Systems with Puronr Refrigerant:

Vertical Separation ft (m)

21---30

(6.4---9.1)

31---40

(9.4---12.2)

41---50

(12.5---15.2)

51---60

(15.5---18.3)

(18.6---21.3)

61---70

71---80

(21.6---24.4)

Maximum Total Equivalent Length

Outdoor Unit ABOVE Indoor Unit

Liquid

Size

18000

AC with

Puron

24000

AC with

Puron

30000

AC with

Puron

36000

AC with

Puron 42000

AC with

Puron 48000

AC with

Puron 60000

AC with

Puron

* Maximum actual length not to exceed 200 ft (61 m) { Total equivalent length accounts for losses due to elbows or fitting. See the Long Line Guideline for details.

--- --- = o u t s i d e a c c e p t a b l e r a n g e

Liquid Line

Connection

3/8

3/8 3/8 250* 250* 250* 250* 250* 250* 250* 250*

Line

Diam.

w/ TXV

1/4 175 250* 250* 250* 250* 250* 250* 250*

5/16 250* 250* 250* 250* 250* 250* 250* 250*

3/8 250* 250* 250* 250* 250* 250* 250* 250* 1/4 100 125 175 200 225* 250* 250* 250*

5/16 250* 250* 250* 250* 250* 250* 250* 250*

3/8 250* 250* 250* 250* 250* 250* 250* 250* 1/4 30 --- --- --- --- --- --- --- --- --- --- --- --- --- --5/16 250* 250* 250* 250* 250* 250* 250* 250*

3/8 250* 250* 250* 250* 250* 250* 250* 250*

5/16 225* 250* 250* 250* 250* 250* 250* 250*

3/8 250* 250* 250* 250* 250* 250* 250* 250*

5/16 175 200 250* 250* 250* 250* 250* 250*

3/8 250* 250* 250* 250* 250* 250* 250* 250*

AC with Puron Refrigerant Maximum Total Equivalent Length{: Outdoor unit ABOVE Indoor

(7.6)

26---50

(7.9---15.2)

51---75

(15.5---22.9)

Vertical Separation ft (m)

76---100

(23.2---30.5)

101---125

(30.8---38.1)

126---150

(38.4---45.7)

151---175

(46.0---53.3)

176---200

(53.6---61.0)

REFRIGERANT CHARGE ADJUSTMENTS

Liquid Line Size Puron Charge oz/ft

3/8

5/16 0.40

1/4 0.27

(Factory charge for lineset = 9 oz)

0.60

Units are factory charged for 15 ft (4.6 m) of 3/8” liquid line. The factory charge for 3/8” lineset 9 oz. When using other length o r diameter liquid lines, charge adjustments are required per the chart above.

Charging

Formula:

[(Lineset oz/ft x total length) – (factory charge for lineset)] = charge adjustment

Example 1: System has 15 ft of line set using existing 1/4“ liquid line. What charge adjustment is required?

Formula: (.27 oz/ft x 15ft) – (9 oz) = (-4.95) oz.

Net result is to remove 4.95 oz of refrigerant from the system

Example 2: System has 45 ft of existing 5/16” liquid line. What is the charge adjustment?

Formula: (.40 oz/ft. x 45ft) – (9 oz.) = 9 oz.

Net result is to add 9 oz of refrigerant to the system

LONG LINE APPLICATIONS

An application is considered Long Line, when the refrigerant level in the system requires the use of accessories to maintain acceptable refrigerant management for systems reliability. See Accessory Usage Guideline table for required accessories. Defining a system as long line depends on the liquid line diameter, actual length of the tubing, and vertical separation between the indoor and outdoor units.

For Air Conditioner systems, the chart below shows when an application is considered Long Line.

AC WITH PURONr REFRIGERANT LONG LINE DESCRIPTION ft (m)

Beyond these lengths, long line accessories are required

Liquid Line Size Units On Same Level Outdoor Below Indoor Outdoor Above Indoor

1/4

5/16 120 (36.6) 50 (15.2) 120 (36.6)

3/8 80 (24.4) 35 (10.7) 80 (24.4)

Note: SeeLongLineGuidelinefordetails

No accessories needed within allowed lengths

175 (53.3)

113A

VAPOR LINE SIZING AND COOLING CAPACITY LOSS

Acceptable vapor line diameters provide adequate oil return to the compressor while avoiding excessive capacity loss. The suction line diameters shown in the chart below are acceptable for AC systems with Puron refrigerant:

Unit

Nominal

Size (Btuh)

18000 1Stage AC with

Puron

24000 1Stage AC with

Puron

30000 1Stage AC with

Puron

36000 1Stage AC with

Puron

42000 1Stage AC with

Puron

48000 1Stage AC with

Puron

60000 1Stage AC with

Puron

Applications in this area may be long line and may have height restrictions. See the Residential Piping and Long Line Guideline.

Maximum

Liquid Line

Diameters

(In. OD)

3/8

Vapo r Line

Diameters

(In. OD)

1/2 1 2 3 5 6 7 8 9 11

5/8 0 1 1 1 2 2 2 3 3

3/4 0 0 0 0 1 1 1 1 1

5/8 0 1 2 2 3 3 4 5 5

3/4 0 0 1 1 1 1 1 2 2

7/8 0 0 0 0 0 1 1 1 1

5/8 1 2 3 3 4 5 6 7 8

3/4 0 0 1 1 1 2 2 2 3

7/8 0 0 0 0 1 1 1 1 1

5/8 1 2 4 5 6 8 9 10 12

3/4 0 1 1 2 2 3 3 4 4

7/8 0 0 0 1 1 1 1 2 2

3/4 0 1 2 2 3 4 4 5 6

7/8 0 0 1 1 1 2 2 2 3

11/8 0 0 0 0 0 0 0 0 0

3/4 0 1 2 3 4 5 5 6 7

7/8 0 0 1 1 2 2 2 3 3

11/8 0 0 0 0 0 0 0 1 1

3/4 1 2 4 5 6 7 9 10 11

7/8 0 1 2 2 3 4 4 5 5

11/8 0 0 0 1 1 1 1 1 1

26--- 50

(7.9---15.2)

51--- 80

(15.5---24.4)

81--- 100

(24.7---30.5)

Cooling Capacity Loss (%)

Total Equivalent Line Length ft. (m)

101--- 125

(30.8---38.1)

126--- 150

(38.4---45.7)

151--- 175

(46.0---53.3)

176--- 200

(53.6---61.0)

201--- 225

(61.3---68.6)

226--- 250

(68.9---76.2)

ACCESSORY THERMOSTATS

THERMOSTAT / SUBBASE

PKG.

T 6 --- P R H 0 1 --- A Programmable Thermidistat

T 6 --- N R H 0 1 --- A Non ---programmable Thermidistat

T 6 --- P A C 0 1 Preferred Series Programmable AC Stat

T 6 --- N A C 0 1 Preferred Series Non --- programmable AC Stat

T 2 --- P A C 0 1 Legacy Series Programmable AC Stat

T 2 --- N A C 0 1 Legacy Series Non--- programmable AC Stat

T 1 --- P A C 0 1 Legacy RNC Series Programmable AC Stat

T 1 --- N A C 0 1 Legacy RNC Series Non --- programmable AC Stat

TSTATBBSEN01---B Outdoor Air T emperature Sensor

TSTATXXBBP01 Backplate for Builder’s Thermostat

TSTATXXNBP01 Backplate for Non --- Programmable Thermostat

TSTATXXPBP01 Backplate for Programmable Thermostat

TSTATXXCNV10 Thermostat Conversion Kit (4 to 5 wires) -- - 10 Pack

ACCESSORIES

113A

KIT NUMBER DESCRIPTION

KAAFT0101AAA FREEZE THERMOSTAT X X X X X X X

KAATD0101TDR TIME DELAY RELAY X X X X X X X

KSALA0301410 LOW AMBIENT PSW X X X X X X X

KSALA0601AAA{ MOTORMASTER 230V X X X X X X X

HC32GE234 MOTOR FAN BALL BEARING X

HC34GE239 MOTOR FAN BALL BEARING X X

HC40GE226 MOTOR FAN BALL BEARING X X

HC38GE219 MOTOR FAN BALL BEARING X

HC40GE225 MOTOR FAN BALL BEARING X

KSAHS1701AAA HARD START (CAP / RELAY) X X X X X X X

KSACY0101AAA CYCLE PROTECTOR X X X X X X X

KSASF0101AAA SUPPORT FEET X X X X X X X

KAACS0201PTC START ASSIST PTC X X X X X X X

KAALS0201LLS LIQUID LINE SOLENOID X X X X X X X

KAAWS0101AAA WINTER START X X X X X X X

KAACH1201AAA CRANKCASE HTR X X X

KAACH1401AAA CRANKCASE HTR X X X X

KSATX0201PUR TXV PURON HSO X X X

KSATX0301PUR TXV PURON HSO X X

KSATX0401PUR TXV PURON HSO X

KSATX0501PUR TXV PURON HSO X

KSASH0601COP SOUND HOOD X X X X X X

KSASH2101COP SOUND HOOD X

KAALP0401PUR LOW PRESSURE SWITCH X X X X X X X

KAAHI0501PUR HIGH PRESSURE SWITCH X X X X X X X

{ Required accessories include ball bearing fan motor, compressor start assist (CAP / Relay), crankcase h eater, evaporator freeze stat, hard shut ---off TXV. X = Accessory

018--- D 024--- D 030 - -- E 036- -- E 042 --- C 048--- E 060 - -- G

DESCRIPTION

Size --- Voltage & Series

ACCESSORY USAGE GUIDELINE

REQUIRED FOR LOW --- AMBI-

ACCESSORY

Ball Bearing Fan Motor Yes{ No No

Compressor Start Assist Capacitor and Relay Yes Ye s No

Crankcase Heater Yes Ye s No

Evaporator Freeze Thermostat Yes No No

H a r d S h u t --- O f f T X V Yes Ye s Yes

Liquid Line Solenoid Valve No No No

Motor Master®Control or

L o w --- a m b i e n t P r e s s u r e S w i t c h

Support Feet Recommended No Recommended

Winter Start Control Yes # No No

* Required for Low ---Ambient Controller (full modulation feature) MotorMasterr Control. { Required for Low ---Ambient Controller (full modulation feature) MotorMasterr Control.

# Required if Low Pressure Switch is factory or field installed.

ENT COOLING APPLICATIONS

(Below 55°F/12.8_C)

Yes No No

REQUIRED FOR LONG

LINE APPLICATIONS*

Accessory Description and Usage (Listed Alphabetically)

1. Ball--Bearing Fan Motor

A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication.

Usage Guideline:

Required on all units when MotorMasterr is used.

2. Compressor Start Assist -- Capacitor and Relay

Start capacitor and relay gives a ”hard” boost to compressor motor at each start up.

Usage Guideline: Required for reciprocating compressors in the

following applications:

Long line Low ambient cooling

Hard shut off expansion valve on indoor coil Liquid line solenoid on indoor coil

Required for single--phase scroll compressors in the following applications:

Long line

Low ambient cooling

Suggested for all compressors in areas with a history of low voltage problems.

3. Compressor Start Assist — PTC Type

Solid state electrical device which gives a ”soft” boost to the compressor at each start-- up.

Usage Guideline:

Suggested in installations with marginal power supply.

4. Crankcase Heater

An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and minimizes the chance of liquid slugging.

Usage Guideline:

Required in low ambient cooling applications.

Required in long line applications. Suggested in all commercial applications.

5. Cycle Protector

The cycle protector is designed to prevent compressor short cycling. This control provides an approximate 5--minute delay after power to the compressor has been interrupted for any reason, including power outage, protector control trip, thermostat jiggling, or normal cycling.

6. Evaporator Freeze Thermostat

An SPST temperature--actuated switch that stops unit operation when evaporator reaches freeze--up conditions.

Usage Guideline:

Required when low ambient kit has been added.

7. Low--Ambient Pressure Switch Kit

A long life pressure switch which is mounted to outdoor unit service valve. It is designed to cycle the outdoor fan motor in order to maintain head pressure within normal operating limits (approximately 100 psig to 225 psig). The control will maintain working head pressure at low--ambient temperatures down to 0_F (--18_C) when properly installed.

Usage Guideline:

A Low--Ambient Pressure Switch or MotorMasterr

Low-- Ambient Controller must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C).

8. MotorMasterr Low--Ambient Controller

A fan--speed control device activated by a temperature sensor, designed to control condenser fan motor speed in response to the saturated, condensing temperature during operation in cooling mode only. For outdoor temperatures down to --20_F (--28.9_C), it maintains condensing temperature at 100_F ±10_F (37.8_C ±

5.5_C).

Usage Guideline:

A MotorMasterr Low Ambient Controller or Low-- Ambient Pressure Switch must be used when cooling operation is used at outdoor temperatures below 55_F (12.8_C).

Suggested for all commercial applications.

9. Outdoor Air Temperature Sensor

Designed for use with Bryant Thermostats listed in this publication. This device enables the thermostat to display the outdoor temperature. This device also

is required to enable special thermostat features such as auxiliary heat lock out.

Usage Guideline:

Suggested for all Bryant thermostats listed in this publication.

REQUIRED FOR

SEA COAST

APPLICATIONS

(Within2miles/3.22km)

113A

Accessory Description and Usage (Listed Alphabetically) (Continued)

10. Sound Hood

Wraparound sound reducing cover for the compressor. Reduces the sound level by about 2 dBA.

Usage Guideline: Suggested when unit is installed closer than 15 ft (4.57 m) to

quiet areas, bedrooms, etc.

Suggested when unit is installed between two houses less than 10 ft (3.05 m) apart.

11. Support Feet

Four stick--on plastic feet that raise the unit 4 in. (101.6 mm) above the mounting pad. This allows sand, dirt, and other debris to be flushed from the unit base, minimizing corrosion.

Usage Guideline:

Suggested in the following applications: Coastal installations. Windy areas or where debris is normally circulating.

Rooftop installations. For improved sound ratings.

113A

12. Thermostatic Expansion Valve (TXV)

A modulating flow-- control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the evaporator.

Kit includes valve, adapter tubes, and external equalizer tube. Hard shut off types are available.

NOTE: When using a hard shut off TXV with single phase reciprocating compressors, a Compressor Start Assist Capacitor and Relay is required.

Usage Guideline:

Required to achieve ARI ratings in certain equipment combinations. Refer to combination ratings.

Hard shut off TXV or LLS required in air conditioner long line applications.

Required for use on all zoning systems.

13. Time--Delay Relay

An SPST delay relay which briefly continues operation of indoor blower motor to provide additional cooling after the compressor cycles off.

NOTE: Most indoor unit controls include this feature. For those that do not, use the guideline below.

14. Winter Start Control

This control is designed to alleviate nuisance opening of the low--pressure switch by bypassing it for the first 3 minutes of operation.

Usage Guideline:

For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.

ELECTRICAL DATA

UNIT

S I Z E ---

VOLTAGE,

SERIES

018--- D

024--- D

030--- E

036--- E

042--- C

048--- E

060--- G

* Permissible limits of the voltage range at which the unit will operate satisfactoril y { If wire is applied at ambient greater th an 30_C , consult table 310 ---16 of the NEC (NFPA 70). The ampacity of non ---metallic ---sheathed cable (NM), trade

name ROMEX, shall be that of 60_C conditions, per the NEC (NFPA 70) Article 336 ---26. If other th a n uncoated (no ---plated), 60 or 75_C insulation, copper

wire (solid wire for 10 AWG or smaller, stranded wire for larger than 10 AWG) is used, consult applicable tables of the NEC (NFPA 70).

} Length shown is as measured one way along wire path between unit and service panel for voltage drop not to exceed 2%. * * T i m e --- D e l a y f u se .

FLA --- F u l l L o a d A m p s LRA --- L o c k ed R o to r A mp s MCA --- Minimum Circuit Amps RLA --- RatedLoadAmps NOTE: Control circuit is 24--- V on all units and requires external power source. Copper wire must be used from service disconnect to unit.

Complies with 2007 requirements of ASHRAE Standards 90.1

V/PH

208/230/1 253 197

All motors/compressors contain internal overload protection.

OPER

VOLTS*

COMPR FAN

MCA

MIN WIRE

SIZE{

MIN WIRE

SIZE{

MAX MIN LRA RLA FLA 60° C 75° C 60° C 75° C

48.0 9.0 0.5 11.8 14 14 66 (20.1) 63 (21.0) 15

58.3 13.5 0.77 17.6 14 14 44 (13.4) 42 (12.8) 25

64.0 12.8 0.77 16.8 14 14 46 (14.0) 44 (13.4) 25

77.0 14.1 1.4 20.5 12 12 61 (18.6) 58 (17.7) 30

112.0 17.9 1.1 23.5 12 12 53 (16.2) 51 (15.5) 40

109.0 19.9 1.4 26.2 10 10 76 (23.2) 72 (22.2) 40

134.0 26.4 1.2 34.2 8 10 62 (18.9) 55 (16.8) 50

MAX

LENGTH

ft. (m)}

MAX

LENGTH

ft. (m)}

A--WEIGHTED SOUND POWER (dBA)

U N I T S I Z E ---

SERIES

018--- D 72 53.5 59.5 63.5 67.0 63.5 59.0 52.5 024--- D 76 55.0 61.5 67.0 71.5 69.0 61.0 55.0 030--- E 74 55.0 63.5 68.5 68.5 65.5 61.0 54.0 036--- E 75 59.5 63.0 68.5 70.0 65.5 61.5 53.5 042--- C 78 57.5 65.0 71.0 73.0 70.5 67.5 62.5 048--- E 80 58.5 67.5 73.5 75.0 70.5 67.5 64.5 060--- G 78 59.0 67.5 71.5 73.5 69.0 66.0 63.5

NOTE: Tested in accordance with ARI Standard 270 ---2008 (not listed in AHRI).

STANDARD

RATING

(dBA)

125 250 500 1000 2000 4000 8000

TYPICAL OCTAVE BAND SPECTRUM (dBA, without tone adjustment)

MAX

FUSE**

or CKT

BRK

AMPS

113A

A--WEIGHTED SOUND POWER WITH SOUND BLANKET (dBA)

U N I T S I Z E ---

SERIES

018--- D 71 55.5 60.5 64.0 66.0 63.0 58.5 52.0 024--- D 74 55.5 60.5 68.5 70.0 67.0 61.0 53.6 030--- E 73 55.5 64.0 68.0 67.0 64.0 60.0 52.5 036--- E 74 59.5 63.0 68.0 69.5 65.0 60.5 50.5 042--- C 77 57.5 65.0 70.5 72.0 70.0 67.0 62.0 048--- E 79 60.5 67.5 73.5 74.5 71.0 68.0 63.5 060--- G 78 59.0 68.0 70.5 72.5 68.0 67.0 63.0

NOTE: Tested in accordance with ARI Standard 270 ---2008 (not listed in AHRI).

STANDARD

RATING

(dBA)

125 250 500 1000 2000 4000 8000

TYPICAL OCTAVE BAND SPECTRUM (dBA, without tone adjustment)

CHARGING SUBCOOLING (TXV--TYPE EXPANSION DEVICE)

UNIT SIZE --- SERIES REQUIRED SUBCOOLING _F(_C)

018--- D 10 (5.6) 024--- D 10 (5.6) 030--- E 10 (5.6) 036--- E 14 (7.8) 042--- C 10 (5.6) 048--- E 15 (8.3) 060--- G 13 (7.2)

AIR IN

113A

SHIPPING

OPERATING

DIMENSIONS (L x W x H)

WEIGHT (lbs)

NOTES:

WEIGHT (lbs)

F, MAX. 1 25

48" ABOVE UNIT, 6" ON ONE SIDE, 12" ON REMAIN ING SIDE,

AND 24" BETWEEN UN ITS FOR PROPER AIRFLO W.

1. ALLOW 30" CLEAR ANCE TO SERVICE SIDE OF UNIT,

MODE IS 5 5

2. MINIMUM OUTDOOR OPERATING AMBIENT IN COOLING UNIT MODEL NUMBER.

3. SERIES DESIGNATION IS THE 14TH PO SITION OF THE

AIR

DISCHARGE

4. CENTER OF GRAVITY .

5. ALL DIMENSIONS ARE IN "INC HES" UNLESS NOT ED. AIR IN

AIR IN

(2) PLACES

5/16"

3/8" TIEDOWN KNOCKOUTS

ABCDEFGKLMNP

ELECTRICAL

CHARACTERISTICS

UNIT SERIES

113A018 D X O O O 23 1/2" 25 5/16" 3 3/4" 3/4" 4 7/16" 18 1/16" 7 13/16" 2 13/16" 1/2" 16 1/2" 15" 12" 107 130 24 1/4" X 27 3/8" X 33 1/2"

17/8"

SQ.

AIR DISCHARGE

X = YES

O=NO

460-3-60

208/230-3-60

230-1-60

208-230-1-60

7/8" HOLE

SUPPLY CONN .

7/8" HOLE WITH

FIELD CONTROL

113A042 C X O O O 31 3/16" 32 5/16" 3 7/8" 7/8" 6 9/16" 24 11/16" 9 1/8" 2 15/16" 5/8" 15 3/4" 16 1/4" 13 3/4" 189 217 32 3/8" X 35 1/2" X 35 15/16"

113A048 E X O O O 31 3/16" 35 3/4" 3 7/8" 7/8" 6 9/16" 24 11/16" 9 1/8" 2 15/16" 5/8" 16 3/8" 15 3/8" 15 1/4" 186 224 32 3/8" X 35 1/2" X 39 3/8"

113A036 E X O O O 25 3/4" 32 5/16" 3 7/8" 7/8" 4 7/16" 21 1/4" 9 1/8" 2 15/16" 5/8" 14 1/4" 10 1/2" 16" 141 170 26 7/8" X 30 1/16" X 35 15/16"

113A060 F, G X O O O 31 3/16" 25 1/2" 3 7/8" 7/8" 6 9/16" 24 11/16" 9 1/8" 2 15/16" 5/8" 14 1/8" 15 3/8" 11 3/4" 190 226 32 3/8" X 35 1/2" X 32 9/16"

113A024 D X O O O 23 1/2" 25 5/16" 3 3/4" 3/4" 4 7/16" 18 1/16" 7 13/16" 2 13/16" 1/2" 16 1/2" 15" 12" 110 134 24 1/4" X 27 3/8" X 33 1/2"

113A030 E X O O O 23 1/2" 28 11/16" 3 3/4" 3/4" 4 7/16" 18 1/16" 7 13/16" 2 13/16" 1/2" 16 1/2" 15" 14" 111 136 24 1/4" X 27 3/8" X 33 1/2"

1 1/8" KNOCKOUT

FIELD POWER SUPPLY CO NN.

31/2"

MINIMUM

DIMENSIONS

MOUNTING PAD

VAPOR LINE CONN .

UNIT SIZE

- 35" X 35"

36 26" X 26"

18,24,30 23 1/2" X 23 1/2"

42,48,60 31 1/2" X 31 1/2"

DIMENSIONS -- ENGLISH

SHIPPING

AIR IN

SHIPPING

OPERATING

DIMENSIONS (L x W x H)

WEIGHT (Kgs)

AIR

C, MAX. 52

WEIGHT (Kgs)

1219.2 ABOVE UNIT, 152.4 ON ONE SIDE, 304.8 ON REMAINING SIDE,

AND 609.6 BETWEEN UNITS FOR PROPER AIRFLOW.

NOTES:

1. ALLOW 762.0 CLEARANCE TO SERVICE SIDE OF UNIT,

MODE IS 1 3

2. MINIMUM OUTDOOR OPERATING AMBIENT IN COOLING UNIT MODEL NUMBER.

3. SERIES DESIGNATION IS THE 14TH PO SITION OF THE

4. CENTER OF GRAVITY .

DISCHARGE

AIR IN

5. ALL DIMENSIONS ARE IN "MM" UN LESS NOTED.

(2) PLACES

8.0

AIR IN

76.2

9.53 TIEDOWN KNOCKOUTS

113A

47.6

X = YES

ABCDEFGKLMNP

O=NO

ELECTRICAL

CHARACTERISTICS

UNIT SERIES

113A018 D X O O O 596.9 643.0 95.2 19.0 112.7 458.8 198.4 71.4 12.7 419.1 381.0 304.8 48.5 59.0 616.0 X 695.3 X 850.9

113A024 D X O O O 596.9 643.0 95.2 19.0 112.7 458.8 198.4 71.4 12.7 419.1 381.0 304.8 49.9 60.8 616.0 X 695.3 X 850.9

113A030 E X O O O 596.9 728.7 95.2 19.0 112.7 458.8 198.4 71.4 12.7 419.1 381.0 355.6 50.3 61.7 616.0 X 695.3 X 850.9

113A036 E X O O O 654.0 820.8 98.4 22.2 112.7 539.8 231.8 74.6 15.9 362.0 266.7 406.4 64.0 77.1 682.6 X 763.6 X 912.8

113A042 C X O O O 792.2 820.8 98.4 22.2 166.7 627.1 231.8 74.6 15.9 400.0 412.8 349.2 85.7 98.4 822.3 X 901.7 X 912.8

113A048 E X O O O 792.2 908.0 98.4 22.2 166.7 627.1 231.8 74.6 15.9 415.9 390.5 387.4 84.4 101.6 822.3 X 901.7 X 1000.1

113A060 F, G X O O O 792.2 647.7 98.4 22.2 166.7 627.1 231.8 74.6 15.9 358.8 390.5 298.4 86.2 102.5 822.3 X 901.7 X 827.1

DIMENSIONS -- SI

SQ.

AIR DISCHARGE

460-3-60

208/230-3-60

230-1-60

208-230-1-60

22.23 HOLE

SUPPLY CONN .

FIELD CONTROL

28.58 KNOCKOUT

22.23 HOLE WITH

FIELD POWER SUPPLY CO NN.

88.9

MINIMUM

DIMENSIONS

MOUNTING PAD

VAPOR LINE CONN .

- 889.0 X 889.0

36 660.4 X 660.4

18,24,30 596.9 X 596.9

UNIT SIZE

42,48,60 800.1 X 800.1

+ 23 hidden pages

Bryant 113A, Legacy 113A Product Data

Specifications and Main Features

Frequently Asked Questions

User Manual