Brother CP-2000 Owner's Manual
CP2000
User’s Manual
Table of Contents
1. Important Safety Precautions 1
2. Setup 2
3. Operation 16
4. Maintenance 21
5. Specifications 26
6. Accessories 27
Thank you for purchasing the Brother CP2000 copyboard. This copyboard has
been designed for easy operation; however, we suggest that you first read this
User’s Manual so that you can install the copyboard safely and use the
copyboard to its fullest potential. In addition, we suggest that you keep this
manual in a handy place for future reference.
If You Need to Call Customer Service:
Please complete the following information for future reference.
Model Number: CP2000
Serial Number*:
Date of Purchase:
Place of Purchase:
* The serial number is on the back of the unit.
Retain this User’s Manual with your sales receipt as a permanent record
of your purchase, in the event of a theft, fire or warranty service.
Compilation and Publication Notice
This manual, covering the latest product descriptions and specifications, has
been compiled and published under the supervision of Brother Industries, Ltd.
The contents of this manual and the specifications of this product are subject to
change without notice.
Brother reserves the right to make changes without notice in the specifications
and materials contained herein and shall not be responsible for any damages
(including consequential) caused by reliance on the materials presented,
including but not limited to typographical and other errors relating to the
publication.
Trademarks
Brother is a registered trademark of Brother Industries, Ltd.
The brother logo is a registered trademark of Brother Industries, Ltd.
All other terms, brand names and product names mentioned in this
manual are registered trademarks of their respective companies.
1. Important Safety Precautions
Read all instructions and save them for future reference. Follow all warnings and instructions indicated on the product.
• To reduce the risk of electric shock, always disconnect all cables from the wall outlets
before servicing, modifying, or installing the equipment. Unplug this product from the
wall outlet and refer servicing to an authorized Brother Service Center under the
following conditions:
a) when the power supply cord is damaged or frayed
b) if foreign objects, such as liquid, metal, or paper scraps, have been dropped into
the product
c) if the product has been exposed to rain or water
d) if the product does not operate normally when the operating instructions are
followed (Adjust only those controls that are covered by the operating instructions.
Improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to normal operation.)
e) if the product produces smoke or an unusual odor
f) if the product has been dropped or the cabinet has been damaged
g) if the product exhibits a distinct change in performance, indicating a need for service
• Use of controls, adjustments, or performance of procedures other than those specified
in this manual may result in hazardous invisible radiation exposure.
• This product should be operated using the type of power source specified. If you are
not sure of the type of power available, consult your dealer or local power company.
• Do not hang on or lean against this unit. Do not subject the printer to strong impacts.
• Use only enclosed AC adaptor (LG2286001).
• Unplug the AC adaptor before moving the unit. Grab the plug, not the cord, when unplugging
the AC adaptor. Never touch the AC adaptor, its cord or the AC cord with wet hands.
• Disconnect the machine from the electrical wall outlet before cleaning. Never use
liquid or aerosol cleaners. Only use a damp cloth for cleaning.
Be sure to turn off the unit after finishing using it. Disconnect the AC cord from the
•
electrical wall outlet and clean it at least once a year. If the unit will not be used for a long
period of time, disconnect the AC adaptor from both the unit and the electrical wall outlet.
• Do not modify the AC adaptor cord or the AC cord.
• Do not pull, excessively bend, or place heavy objects on the AC adaptor cord or the AC cord.
• Do not remove any covers or screws other than those specified.
• Do not insert your fingers or hands into the printer while it is printing.
• Important information is indicated by the following symbols.
+
bc This symbol indicates precautions that should be observed in order to
a This symbol indicates precautions that should be observed in order to avoid
This symbol indicates notes or additional information.
prevent damage to or malfunction of the machine.
injury or property damage.
1
2. Setup
Package contents
Check that the following items are enclosed.
CP2000 copyboard AC adaptor & AC cord
Owner’s Manual
2 partition-mounting
brackets
4 screws
Tray 2 Dry Erase markers Eraser Seals
Starter Therma PLUS paper
(up to 30 pages)
2 L-shaped brackets
Wall-mounting bar
2 wall-mounting brackets
6 anchors
6 washers
bc When shipping the copyboard or transporting it over a long distance, be sure to
use the original packing materials that it was supplied in. Improperly packing the
machine may void the warranty.
Be careful not to damage the printer control panel while unpacking it, transporting it, or while removing and installing the printer or stand.
If an item is missing, contact Brother Customer Service at:
1-800-276-7746 (in the USA), 1-800-853-6660 (in Canada), or
1-514-685-6464 (in Montreal)
See section 6. Accessories on page 27 for item numbers.
2
2. Setup
Choosing a location
• Set up the unit on a stable surface or a sturdy wall that is free from vibrations and shocks.
• Do not set up this unit in a high-traffic area or near heaters, air conditioners, refrigerators, liquids, or chemicals.
• Do not set up this unit in a location where it will be exposed to direct sunlight,
excessive heat, moisture, or dust.
• Do not set up this unit near speakers, the base units of cordless phones, or other
sources of interference.
• Do not allow anything to rest on the power cord. Do not place this product where the
cord may be walked on.
• Lightning and power surges can damage this product. We recommend that this unit be
used with a surge protection device, or be unplugged during lightning storms.
• If an extension cord is used with this product, make sure that the total ampere rating
of all products plugged into the extension cord do not exceed the extension cord
ampere rating. The total of all products plugged into the wall outlet must not exceed
15 amperes (USA only).
Setup
The versatility and portability of the CP2000 copyboard allows it to be set up in various
locations on its stand, or mounted on a partition or a wall.
Stand (Refer to pages 4
through 6 for details on setting
up the stand.)
Wall mounting (Refer to pages 8 through 13 for
details on mounting the copyboard on a wall.)
Partition mounting
(Refer to pages 13 and 14
for details on mounting
the copyboard on a
partition.)
3
2. Setup
Stand
Setting up the stand
a Do not allow young children to play on or near the copyboard when it is set up
+ After removing the copyboard from its box, keep the printer and writing surface
1 Lay the copyboard on the floor
2 Grab the leg of the stand as shown in the illustration and slowly fold
on its stand.
covered in the bubble wrap packaging while setting up the copyboard.
facing downward with the printer
control panel and writing surface
positioned over a piece of cloth or
other protective sheet to prevent
them from being damaged.
bc Do not exert pressure on the copyboard.
+ If the printer has been installed on the long edge of the copyboard, refer to
step 5 on page 12 for details on installing the printer on the short edge
before continuing this procedure.
If the stand is not attached, refer to page 15 for details on re-attaching it.
out the stand.
a Be careful not to pinch your finger between the plastic projection on
each leg of the stand and the stopper.
4
2. Setup
3 Align the screws on the knobs with the holes in the brackets, and then
tighten each knob (one on each side).
+ While tightening each knob, it may be necessary to lift up the lower leg
slightly so that the screw on the knob correctly enters the hole in the
bracket.
4 Carefully lift up the copyboard to set it
up on its stand, and then spread the
legs completely.
a To reduce the risk of the copyboard
falling down and causing injuries, do
not loosen the knobs on the stand
when the stand is in use.
5 Turn the adjuster on the end of each
back leg until the stand is stable.
a To reduce the risk of the copyboard
falling down and causing injuries, be
careful that the copyboard does not
tip over.
5
2. Setup
6 Attach the tray by sliding its slots on each sides of back of the tray
Folding up the stand
a Do not allow young children to play on or near the copyboard when it is set up
over the two brackets on the front of the copyboard above the printer.
bc Do not subject the tray to strong impacts or use it in any way other than
for holding markers and erasers.
+ Remove the bubble wrap packaging covering the printer and writing
surface.
on its stand.
To reduce the risk of the copyboard falling down and causing injuries, do not
loosen the knobs on the stand or pull the blue pin on the left leg while the stand
is in use.
1 Make sure the copyboard is turned off and the AC adaptor is unplugged.
2 Pull up on the tray to remove it, and then remove the paper from the
printer.
3 Lay the copyboard on the floor facing downward with the printer control
panel and writing surface positioned over a piece of cloth or other
protective sheet to prevent them from being damaged.
6
2. Setup
4 Slightly lift up each bottom leg and loosen the knobs (one on each side
of the stand).
5 Slightly lift up the bottom leg and pull the blue pin on the right side of
the stand.
6 Grab the topmost bar and carefully fold up the stand so that it rests on
the sponges on the back of the copyboard.
1
2
+ The sponges on the back of the copyboard should not be removed since
they act as a cushion between the copyboard and the stand.
7
2. Setup
After folding up the stand, the CP2000 can be carried using the handle on the back.
a Be sure to use the handle to transport the
bc While transporting the copyboard, be careful
copyboard. Do not transport the unit by
carrying it by its stand, otherwise the stand
may open up and the copyboard may fall
down.
not to drop it, scratch it, or hit it against
anything.
Wall mounting
With the enclosed wall-mounting bar and brackets, the copyboard can easily be mounted
on a wall. In addition, by installing the printer on either a short or long edge of the
copyboard, the unit can be positioned either vertically or horizontally.
Attaching the wall-mounting bar
Follow the precautions below to mount the copyboard correctly on the wall
and reduce the risk of it falling down.
a Use the enclosed anchors to attach the wall-mounting bar to plasterboard that is
+ Before mounting the copyboard on the wall, set it up on its stand and check that
at least 0.5 in. to 0.63 in. (12.7 mm to 15.9 mm) thick. When mounting the
copyboard on other types of walls, consult with a contractor first and be sure to
use the appropriate types of screws.
Make sure that there is no metal, wood, or wires behind the wall at the points
where the anchors will be installed.
it is operating correctly.
During installation, keep in mind that an anchor is difficult to remove once it has
been installed in the wall.
1 Hold the wall-mounting bar against the wall at the position where it
will be attached, making sure that it is level, and then mark the wall at
the four points where the anchors will be installed.
+ Be sure to attach the bar using either pair of holes A or B together with
either pair of holes C or D.
It is recommended that holes A and D be used. However, holes B and C
can be used if necessary.
8
Loading...