Page 1
Page 2
1
Folding the Jacket Case into a Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Location of Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Charging the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Syncing the Bluetooth
®
to your iPad Tablet . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . 6
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TABLE OF CONTENTS
10
Page 3
9 2
5
FOLDING THE JACKET CASE INTO A STAND
Holds iPad Vertically at almost any angle
Place on a flat surface. Stand holds the iPad
Tablet horizontally at almost any angle.
Magnets will stick to form a stand
4
Fold corners in
Put your iPad Tablet in shell case
Page 4
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B
Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This equipment may not cause harmful interference.
2. This equipment must accept any interference received, including interference
that may cause undesired operation.
Modifications not authorized by the manufacturer may void the user’s authority
to operate this device.
TROUBLESHOOTING
ISSUE SOLUTION
The keyboard will not
work with my iPad Tablet.
Make sure that the keyboard is
synced correctly. Power the keyboard
off and then on and try again.
If the iPad Tablet has been upgraded,
or you are using a different iPad Tablet,
resync using the steps on the previous pages.
Check the battery power.
You may need to recharge the
Bluetooth
®
Keyboard Case.
Make sure that both your iPad Tablet
and the Bluetooth
®
Keyboard Case
are on and in good working order.
iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
3 8
Page 5
Page 6
CHARGING THE KEYBOARD
SYNCING THE BLUETOOTH
®
KEYBOARD TO YOUR
iPad Tablet
2. The LED will illuminate in red during charging, and shut off when charging is
complete.
3. The keyboard takes approximately 1.5 hours to charge for up to 280 hours of use.
Note: The charging LED indicator will blink when your Bluetooth® Keyboard
Case’s battery is low and needs to be recharged.
Charging LED
Bluetooth
®
LED
Caps Lock LED
Charging Outlet
Note: The Bluetooth
®
Keyboard will automatically go into standby mode
after 15 minutes of inactivity in order to preserve battery life. Just press any
key to reactivate the keyboard.
1. Plug the USB charging cable (included) into the charging outlet and into a USB
outlet (see the illustration below for part locations).
1. Power on your iPad.
2. Press the Power button on the Bluetooth
®
Keyboard. The Blue LED will shut
off after a few seconds.
3. Press the Fn+ on the Bluetooth
®
Keyboard, the Blue LED will fash.
4. Select the “Settings” icon on your iPad Tablet’s screen.
5. Locate and select “Bluetooth” in your iPad Tablet’s “General” menu.
6. Under “Devices” on your iPad Tablet, selcet the Brookstone Bluetooth
®
Keyboard.
7. The iPad Tablet screen should now show the Brookstone Bluetooth
®
Keyboard
has connected successtully.
8. If your iPad Tablet goes into standby mode, the Bluetooth
®
Keyboard should
still be synced. If you power-off your iPad Tablet you may need to re-sync. If you
use the Bluetooth
®
Keyboard with a new iPad Tablet, or it doesn’t connect
properly, follow the setps above to re-sync.
5 6
Loading...