Fold Fold Fold Fold
LOCATION OF PARTS AND
CONTROLS
PAIRING YOUR DEVICE
1. Press and hold the Power Button for
3 seconds to power on the
headphones. The blue light will
illuminate.
2. If the Button is pressed and held, the
headphones will search for
Bluetooth
®
enabled devices. The red
and blue lights will flash alternatively.
3. Once the headphones are in pairing
mode and your device is ready to
pair, select ‘Brookstone Headphones.’
If prompted, use 0000 as a PIN for
the pairing code. Once the
headphones are selected, a beep
tone will sound and the blue light
will flash.
NOTE:
If the headphones were powered on
and without Bluetooth
®
connection for
3 minutes, they will auto shut off. After
a successful connection, the blue LED
will flash three times every 5 seconds
(Bluetooth
®
connected but not playing
music)
1. Power Button
2. Volume Up/Track Backward Button
3. Volume Down/Track Forward Button
4. Microphone
5. Audio Cable Port
6. Micro USB Charging Port
7. Micro USB Charging Cable
(not shown)
8. Audio Cable (not shown)
9. Travel Pouch (not shown)
306612
1
2
4
5
6
3
Merrimack, New Hampshire, USA 03054
800-846-3000 • Brookstone.com
LITHIUM-ION BATTERY
WARNINGS
This device contains a non-removable
lithium-ion battery. The battery must be
recycled or disposed of properly.
Contact your local waste management
office for information on battery
recycling or disposal.
FCC IN FORMATION
This equipment has been tested
and found to comply with the
limits for a Class B Digital Device,
pursuant to Part 15 of the FC C
Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and receiver.
• Connect the equipment to an outlet
on a circuit different
from that to
which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
This equipment complies with Part 15
of the FCC Rules. Operation is subject
to the following two conditions:
1. This equipment may not cause
harmful interference.
2. This equipment must accept any
interference received, including
interference that may cause
undesired operation.
Modifications not authorized by the
manufacturer may void the user’s
authority to operate this device.
FCCID: 2AF8E-WL-2706
FoldFoldFold
CHARGING THE HEADPHONES
The headphones are equipped with
non-removable built-in battery that can
be charged repeatedly. When used for
the first time, please make sure that the
headphones are fully charged.
1. Connect the USB charging cable to
the charging port on the headphones.
2. Insert the charging cable into the
standard power socket. During
charging process, the indicator light
will become red. If the charging has
not been started, please unplug the
charger and then re-insert it.
3. After the headphones are fully
charged, the red indicator light will
turn off. ln this case, please unplug
the charger from the power socket
and headphones.
• Repeated charging and discharging
of the headphones may lead to the
declined battery performance over
time.
• During charging, please be sure
not to make or receive phone calls
using the headphones.
NOTE: When the battery capacity
of headphones is not adequate, the
indicator light of headset will flash
red, and you will hear the alarm or
"The headset battery capacity is
low." If the headphones are shut
down during the time when you
make phone calls, these calls will
SPECIFICATIONS
Power Supply: 3.7V, 300mAh
DC Input: 5V, 1A
Range: Class 2, up to 33 ft (10m)
Driver: 40 mm Dia.
Frequency Response: 20Hz~20KHz
Sensitivity @ 1KHz: 110 +/- 3 dB
Charging Time: Approx. 2 hours
Battery Life: Approx. 14 hours
Compatibility: Bluetooth
®
2.0 or above
device with A2DP/AVRCP/HFP/HSP
MOBILE PHONE OPERATION
When the headphones are paired to
your device and a call is received, the
incoming call tone will sound.
If there is audio playing through the
headphones when a call is answered,
the audio will pause and only your call
will be audible. When you end the call,
your audio will resume.
1. Receiving call: When the bell rings,
short press the Power Button for 1
second.
2. Hanging up calls: At the end of calls,
short press the Power Button for 1
second.
3. Rejecting calls: When the bell rings,
press and hold the Power Button for
2 seconds.
RESET
To hard reset the headphones, connect
to the USB cable and plug into a
charging source.
CARE AND MAINTENANCE
Do not submerge the headphones in
water. To clean, wipe the headphones
with a soft, dry cloth.
The Bluetooth
®
word mark and logos
are registered trademarks owned of
Bluetooth SIG, Inc. and any use of such
marks by Brookstone is under license.
be automatically transferred to your
mobile phone. The headphones will
shut off when AUX/MICRO input is
used, and you will need to unplug and
power on again for music to play.
LISTENING TO AUDIO
1. Press the Power Button once to play
music. Press the Power Button
again to pause the music.
2. Short press the Volume "+" button
one time to go to the previous song
or beginning of current song. Short
press the Volume "-" button to go to
the next song.
3. In the process of playing music or
receiving calls, a long press of the
Volume "+" or "-" buttons will
increase or decrease the volume
level to desired level.
PLAYING MUSIC THROUGH A
WIRED CONNECTION
Plug one end of the audio cable
(included) into your audio device and
plug the other end of the cable into the
headphones’ Aux-In port.
Fold
Fold
Loading...