You have chosen the finest grill for your outdoor cooking pleasure. Please take time to read this entire manual
before assembling your premium Broilmaster® accessory.
Important Information ........................................................................................................................................ 4
Patio Base Parts List & Exploded View ............................................................................................................ 5
Patio Base Assembly ....................................................................................................................................... 6-8
B101075-1-0807
Page 3
IMPORTANT INFORMATION
Grill Location
Broilmaster Premium Gas Grills are designed for outdoor use ONLY.
These mounting accessories are designed for use with
Broilmaster gas grills and must not be used with any
other grill or for any other purpose.
Never install or operate your grill in any building, garage,
or other enclosed area.
For your safety, the grill should not be installed or oper
ated under any combustible materials, such as carports,
covered porches, awnings, or overhangs.
Never install or use your grill in or on any recreational
vehicle or boat.
A minimum clearance of sixteen (16") inches is required
from all sides of the grill to any combustible material.
HEINSTALLATIONANDOPERATIONOFTHISGRILLAT
Gas Types
Never use liquid propane gas with a grill designed for
natural gas, or natural gas with a grill designed for liquid
propane gas. The type of gas required for your grill is
defined on its product identification label. Questions
regarding different types of gases should be directed
to your gas supplier.
Cleaning
The exterior of your post may be cleaned with hot water
-
and mild detergent as needed.
Touch-up paint is available through your Broilmaster
dealer.
Stainless steel surfaces may be cleaned with a sprayon stainless steel cleaner available at most hardware
stores.
Important: Do not use harsh or abrasive cleaners! Your
post has a highly polished surface and may be easily
scratched.
A minimum clearance of eighteen (18") inches is re
quired from the back of the grill to any combustible
material.
Examples of combustible materials are patio furniture,
fences, or the wall of your home.
The area surrounding the grill should be clear to ensure
proper ventilation. Do not obstruct the flow of com
bustion and ventilation air in any way. The ventilation
openings on the propane cylinder enclosure must also
remain free and clear of debris.
Periodic inspections and maintenance are essential. All
Broilmaster Gas Grill products or mechanical devices
eventually begin to wear due to environment, contaminants, corrosion or aging. Inspect all components at
least twice per year and replace any that show wear.
If any parts are damaged or missing, you may order
parts from your local Broilmaster dealer. Please refer to
the Parts Diagram and Parts List section of this manual
for more detailed information.
Page 4
B101075-1-0807
PATIO BASE PARTS LIST & EXPLODED VIEW
6
5
4
1
2
3
10
5
8
9
3
2
1
1
3
2
7
All repair part orders should be placed through your local Broilmaster dealer. To locate a dealer in your area, contact Broilmaster Customer Service at 800-851-3153 • www.broilmaster.com To ensure prompt and accurate service, please provide
the following information when placing a repair part order: Model Number, Part Name, Part Number, and Quantity of parts
needed.
The BPB26 and SSPB26 Patio Base are only for use
with Broilmaster Gas Grills. Before proceeding with
installation read the Owner’s Manual for the proper location and minimum clearances to combustible materials
for your grill and patio base.
2
Fasten the bottom of the post to the cast iron patio
base (9) using 9/32 ID x 5/8 OD flat washers, 1/4 lock
washers, and 1/4-20 hex nuts. FIGURE 2.
Verify that all parts listed in the exploded view of this
product have been included before beginning this in
stallation.
Recommended Tools:
• Two adjustable wrenches or a socket set
• A medium Phillips screwdriver
• Pipe thread sealer or Teflon tape (for gas connec
tions)
• Soapy water solution (to test for leaks)
1
Attach four 1/4-20 x 4" eyebolts (8) to the bottom of the
26" square post (7) using 1/4 - 20 x 3/4" bolts (5), 9/32
ID x 5/8 OD flat washers (1), 1/4 lock washers (2), and
1/4-20 hex nuts (3). Figure 1.
NOTE: The large rectangular cut out is located at the
front of the post near the top.
Anchor the cast iron patio base to your patio using
the two holes provided in the base. (Hardware not
included)
Note: Make sure that the large rectangular cut out is
facing in the direction that you want your grill to face.
F
IGURE 2.
-
Page 6
Figure 2
3
Insert the stainless steel flex tube assembly into the
post.
The inlet side of the gas tubing may protrude from the
bottom of the patio base or through the large circular
hole in the back of the square post.
Note: Do not attempt to cut or alter the flex tube in any
way.
Figure 1
B101075-1-0807
PATIO BASE ASSEMBLY
4
Fasten the four 1/4-20 x 1 3/4" eyebolts (4) to the top
of the square post using 1/4 - 20 x 3/4" bolts, 9/32 ID
x 5/8 OD flat washers, 1/4 lock washers, and 1/4-20
hex nuts.
Position the grill head onto the eyebolts and fasten with
1/4 lock washers and 1/4-20 Hex nuts. FIGURE 3.
5
Arrange with your local gas company or licensed contractor to have a gas supply line connected to the inlet
of the stainless steel flex tube assembly. The gas supply
must have a shutoff valve inside the wall and must be
shutoff when the grill is not in use.
Use pipe thread sealant or Teflon tape at the threads
of each connection being careful to not allow any of
these materials into the flare seat. Test for gas leaks
as directed by the grill’s Owners Manual.
The grill and its individual shutoff valves must be dis
connected from the gas supply piping system during
any pressure testing of that system at test pressures
in excess of 1/2 PSIG.The grill must be isolated from
the gas supply piping system by closing its individual
manual shutoff valves during any pressure testing of
the gas supply piping system at test pressures equal
to or less than 1/2 PSIG.
WARNING: D
FORNATURALGASORNATURALGASTOAGRILLDESIGNEDFOR
LP GAS.
ONOTSUPPLY LP GASTOAGRILLDESIGNED
-
Figure 3
Gas leak tests should be completed as directed in the
grill owner's manual.
B101075-1-0807
Page 7
PATIO BASE ASSEMBLY
6
Attach the grease cup bracket assembly (10) to the
bottom of the grill casting and fasten with 10-24 x 3/4"
bolt, 9/32 ID x 5/8 OD washer, and #10-24 wing nut.
Figure 4.
Loosen the wing nut and move the slide up or down to
accept the grease cup. Be sure to trap the rim of the
cup as shown.
Use only the supplied grease cup or noncombustible
containers for the grease cup (aluminum or tin cans).
DO NOT use combustible containers such as Styrofoam
or paper cups.
7
Figure 4
Attach the control housing (6) using two #8 x 1/2" Phillips
Truss screws or two plastic panel fasteners as shown
in Figure 5.
8
Continue assembly as directed by the Owner’s Manual
packaged with the grill head.
BROILMASTER
is a registered trademark of
Empire Comfort Systems, Inc.
918 Freeburg Ave.
Belleville, Illinois 62220
Phone: 1-800-851-3153
FAX: 1-800-443-8648
Figure 5
®
Page 8
V
ISITOURWEBSITEATWWW.broilmaster.com
B101075-1-0807
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.