Broil King Installation Instructions And Owner's Manual
Specifications and Main Features
Frequently Asked Questions
User Manual
INSTALLATION INSTRUCTIONS
GRILL SHOWN WITH OPTIONAL SCG-36 CART
AND
The Superb Series
OWNER'S MANUAL
OUTDOOR
COOKING APPLIANCE
SSG-36-1
EFFECTIVE DATE
APRIL, 2003
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your supplier or your fire department.
FOR YOUR SAFETY
1. Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
WARNING: If not installed, operated and maintained in accordance with the manufacturer's
instructions, this product could expose you to
substances in fuel or from fuel combustion
which can cause death or serious illness.
AVERTISSEMENT
S'il y a une odeur de gaz:
1. Coupez l'admission de gaz de l'appareil.
2. Éteindre toute flamme nue.
3. Ouvrir le couvercle.
4. Si l'odeur persiste, appeler immédiatement votre
compagnie de gaz ou votre département des
incendies.
AVERTISSEMENT
1. Ne pas entreposer ni utiliser de l'essence ni
d'autres vapeurs ou liquides inflammables
dans le voisinage de l'appareil, ni de tout autre
appareil.
2. Une bouteille de propane que n'est pas recordée
en vue de son utilisation, ne doit pas être
entreposée dans le voisinage de cet appareil ou
de tout autre appareil.
AVERTISSEMENT: Si l’installation, l’usage et
l'entretien de ce produit ne sont pas faits selon
les instructions du fabricant, ce produit peut vous
exposer à des matières contenues dans le carburant
ou provenant de la combustion du carburant
lesquelles peuvent causer la mort ou de sérieuses
maladies.
R-3848-0-0403Page 1
IMPORTANT WARNINGS
For Outdoor Use Only.
If Stored Indoors,
Detach and Leave Cylinder Outdoors.
• Read instructions before lighting.
• Open lid during lighting.
• If ignition does not immediately take place, turn the burner valve
handles to OFF, wait 5 minutes, and repeat the lighting procedure.
• Minimum clearance from sides and back of unit to adjacent combustible
construction below top of unit, 6 inches from sides and 12 inches from
back.
• Minimum horizontal clearance from sides and back of unit to adjacent
vertical combustible construction extending above top of unit, 6 inches
from sides and 12 inches from back.
• Do not locate this outdoor cooking gas appliance under overhead
unprotected combustible surfaces.
• WARNING: Electrical Grounding Instructions
This outdoor cooking gas appliance is equipped with a three-prong
(grounding) plug for your protection against shock hazard and should
be plugged directly into a properly grounded three-prong receptacle.
Do not cut or remove the grounding prong from this plug.
• Keep any electrical supply cord and the fuel supply hose away from
any heated surfaces.
• DO NOT put anything around the outdoor cooking appliance that will
obstruct the flow of combustion and ventilation air.
• DO keep the outdoor cooking gas appliance area clear and free from
combustible material, gasoline and other flammable vapors and liq
uids.
• Do make visual check of burner flames. Clean and replace damaged
parts.
• This outdoor cooking gas appliance is not intended to be installed in
or on recreational vehicles and/or boats.
• This outdoor cooking gas appliance shall be used only outdoors and
shall not be used in a building, garage or any other enclosed area.
Pour Utilisation à l'Extérieur Seulement.
Si l'Appareil est Entre posé à l'Intérieur,
Enlever les Bouteilles et les Laisser à l'Extérieur.
• Lire les instructions avant d'allumer l'appareil.
• Ouvrir le couvercle avant d'allumer l'appareil.
• Si l'appareil ne s'allume pas immédiatement, fermer le robinet
du brûleur, attendre 5 minutes puis procéder de nouveau à
l'allumage.
• Dégagement minimal à respecter entre les côtes et l'arrière de l'appareil
et une construction combustible adjacente située au-dessous de la
partie supérieure de l'appareil, soit 6 pouces des côtés et 12 pouces
de l'arrière.
• Dégagement horizontal minimal à respecter entre les côtés et l'arrière
de l'appareil et une construction combustible verticale adjacent
dépassant la partie supérieure de l'appareil, soit 6 pouces des côtés
et 12 pouces de l'arrière.
• Il est interdit d'installer le présent appareil au-dessous des surfaces
combustibles non protégées.
• AVERTISSEMENT: Instruction Pour la Mise à la Terre Électrique
Cet appareil est muni d'une fiche à trois broches (mise à la terre) afin
de vous protéger des chocs et doit être branché directement dans
une prise de courant à trois broches adéquatement mise à la terre.
Il ne faut pas couper ou enlever la broche de mise à la terre de cette
fiche.
-
PROPANE (LP) GAS WARNINGS
CUSTOMER WARNING:
• Know the odor of LP Gas. If you hear, see or smell leaking LP gas,
immediately get everyone away from the cylinder and call the Fire
Department. Do not attempt repairs.
• LP Gas is heavier than air and may settle in low places while dissipat
ing.
• Contact with the liquid contents of cylinder will cause freeze burns
to the skin.
• Do not allow children to tamper or play with cylinder.
• When not connected for use, keep cylinder valve turned off. Self
contained outdoor cooking appliances shall be limited to a cylinder
of 20 lb. capacity or less.
• Do not use, store or transport cylinder where it would be exposed to
high temperatures. Relief valve may open allowing a large amount of
flammable gas to escape.
• When transporting, keep cylinder secured in an upright position with
cylinder valve turned off.
• CAUTION: The gas pressure regulator provided with this outdoor
cooking gas appliance must be used. This regulator is set for an outlet
pressure of 11 inches water column. (The outlet pressure specified by
the manufacturer.)
• The gas supply must be turned off at the LP gas supply cylinder when
this outdoor cooking gas appliance is not in use.
• The LP gas supply cylinder must be disconnected when this outdoor
cooking gas appliance is not in use.
AVERTISSEMENT:
• Savoir reconnaître l'odeur du GPL. Si vous entendez un sifflement
ou si vous sentez une fuite de GPL, demander immédiatement à
toutes les personnes présentes de s'éloigner de la boutielle et appeler
-
le service d'incendie. Ne pas essayer de la réparer.
• Le GPL étant plus lourd que l'air, il peut s'accumuler près du sol
avant de se dissiper.
• Tout contact de la peau avec la phase liquide de la bouteille causera
des brûlures par le froid.
• Empêcher les enfants de manipuler la bouteille ou de jouer avec.
• Lorsque la bouteille n'est pas raccordée à l'appareil, en maintenir
fermé le robinet. Pour les appareils de cuisson autonomes d'extérieur,
utiliser une bouteille d'une capacité maximale de 9 kg (20 lb.).
• Ne pas utiliser, entreposer ou transporter la bouteille en l'exposant à
une température excessive car la soupape de sûreté risque de s'ouvrir
et de laisser échapper une grande quantité de gaz inflammable.
• Pour transporter une bouteille de GPL, la maintenir solidement fixée
en position verticale avec le robinet fermé.
• MISE EN GARDE: Le régulateur de pression de gaz prévu avec
cet appareil de cuisson à gaz pour l'extérieur doit être utilisé. Ce
régulateur est réglé pour une pression de sortie de 11 pouces de
colonne d'eau (la pression de sortie spécifiée par le manufacturier.
• L'alimentation du gaz doit être fermée à la bouteille de gaz de pétrole
liquéfié, lorsque cet appareil de cuisson extérieur n'est pas utilisé.
• La bouteille d'alimentation en gaz de pétrole liquéfié doit être
débranché lorsque cet appareil de cuisson extérieur n'est pas
utilisé.
Page 2R-3848-0-0404
SPECIFICATIONS
Specifications
Model SSG-36
Input BTU/HR (KW/H) Max. Min.
5 Main Burners 12,000/Burner 5,000
1 Side Burner 30,000 5,000
2 Rotisserie Burners 12,000/Burner
Height (grill only) 27 1/8"
Width 55 1/4"
Depth 31"
Gas Inlet 1/2"
General Information
This appliance is design certified in accordance with American National
Standards Institute Z21.58b-2002 and CGA-1.6b-2002 by the Canadian
Standards Association as an outdoor cooking gas appliance to be installed
according to these instructions.
Any alteration of the original design, installed other than as shown
in these instructions or use with a type of gas not shown on the rat
ing plate is the responsibility of the person and company making
the change.
-
IMPORTANT
All correspondence should refer to complete Model number, Serial
number and type of gas.
Accessories
SCG-36 Stainless Steel Cart
GHK-12 Quick Disconnect 12 ft. Hose LP & Nat.
TKS-36 Stainless Steel Cooking Utensils
SGD-36 Stainless Steel Door for Built-in
GSS-36 Stainless Steel Side Shelf for Left or Right
GIJ-36 Stainless Steel Liner for Built-in
SUW-15 15" Stainless Steel Wok
VCC-36 Vinyl Cover for Grill on Cart
VCB-36 Vinyl Cover for Grill Built-in
SSP-1 Steamer Pan with Lid (1 Small & 1 Large)
Initial Operation
Before cooking food on your grill for the first time, operate the (5) main
burners at 500°F for 30 minutes. The high temperature will remove any
residues from the new components.
LP GAS CYLINDER INFORMATION
WARNING: Inspect the fuel supply hose before each use of
the outdoor cooking gas appliance. The hose can be accessed
by opening the front door on the outdoor cooking gas appli
ance. If it is evident there is excessive abrasion or wear, or the
hose is cut, it must be replaced prior to the outdoor cooking gas
appliance being put into operation. Contact Empire Comfort
Systems, Inc. to obtain a replacement fuel supply hose. Keep
the ventilation opening(s) of the cylinder enclosure free and
clear from debris.
WARNING: Do not store a second 20 lb. propane cylinder within
the utility cart. The utility cart is designed for the use and storage
OVERFILL PROTECTION DEVICE (OPD) ON 20 LB.
PROPANE CYLINDER
Attention: Consumer be advised, this gas grill must be connected
to an LP gas cylinder incorporating an OPD.
The OPD will help reduce the potential for the overfilling of the pro
pane cylinder, thus reducing the possibility of hydrostatic relief valve
discharges.
Overfill Protection Device Valve Function
1. As the cylinder is filled, the rising level of liquid propane lifts the
float to the stop position to prevent dangerous overfilling.
Does not affect the filling process or use of the cylinder.
2. At a safe filling level, the float cam triggers the pin to fall into the
recess of the cam, sealing this path off and preventing any more
liquid propane from flowing through the lower valve body into the
cylinder.
3. The propane builds up pressure in the chamber (center spring) and
pushes the piston up to form a seal, effectively stopping the filling
process.
4. The use of the propane from the cylinder allows the OPD to reset
itself for the next fill.
R-3848-0-0403Page 3
• LP-gas supply cylinder to be used must be constructed and marked
in accordance with the specifications for LP-gas cylinders of the
-
-
U.S. Department of Transportation (DOT) or the National Standard
of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for the
Transportation of Dangerous Goods.
If the outdoor cooking gas appliance is not in use, the gas must be
turned off at the supply cylinder.
• Storage of an outdoor cooking gas appliance indoors is permissible
only if the cylinder is disconnected and removed from the outdoor
cooking gas appliance.
Cylinders must be stored outdoors out of the reach of children and
must not be stored in a building, garage or any enclosed area.
• The pressure regulator and hose assembly supplied with the outdoor cooking gas appliance must be used. A replacement pressure
regulator and hose assembly for this outdoor cooking gas appliance
can be obtained by contacting Empire Comfort Systems, Inc.
5. Connects to all standard or quick-connect couplings.
6. The Overfill Protection Device affects incoming liquid propane flow
only. Does not affect normal propane gas discharge when properly
connected to the appliance regulator.
7. All propane cylinders should be filled by qualified professionals
only.
Purging
1. Due to the decreased Btu delivery, purging may take longer.
2. To increase the speed of purging, open the outage valve during
release.
3. Reminder: Each new cylinder must be purged before filling.
4. For purging instructions, refer to NPGA 133-89(a).
Btu Delivery
The OPD valve has a size 56 orifice through which the propane is released
for consumption. Depending on the propane's temperature and pressure,
the release from the cylinder is approximately 125,000 Btu/hour.
IMPORTANT INFORMATION ABOUT YOUR NEW TYPE-1
GRILL CONNECTION
Read all grill and related product literature before connecting or using
your grill, and please read the following information completely before
attempting to connect your grill to a propane cylinder.
Keep these instructions in a safe place. You may need to refer to them
when connecting other cylinders after filling.
Your new grill regulator is equipped with a coupling nut . Do not attempt
to connect any propane cylinder not equipped with a mating Type-1
cylinder valve.
Figure 1
Connecting the Regulator to the Valve (Figure 1)
This Type-1 cylinder valve contains a backcheck which is designed to
prevent propane from flowing until the valve is properly connecting to
a regulator.
When connecting the regulator to the Type-1 cylinder valve, be sure the
pressure relief valve is directed away from the front of the grill and
away from any building. If the pressure relief valve should open, the
propane will then be directed where it is likely to do the least harm if
ignited.
WARNING: Do not insert any foreign objects into the valve outlet.
You may damage the backcheck. A damaged backcheck can be the
source of a leak. Leaking propane may result in explosion, fire,
personal injury or death.
Regulator Coupling Nut
The coupling nut connects to the large outside threads on the valve outlet.
To complete the connection, follow the steps below.
1. Be sure all grill burner knobs, side burner knob and rotisserie burner
knob are in the OFF position.
2. Make sure the cylinder valve handwheel is in the closed position.
Turn clockwise (left to right) to a full stop.
3. Remove the protective caps from the cylinder valve and coupling
nut.
4. Turn the coupling nut clockwise (left to right), to tighten to a full
stop.Be sure the coupling nut is not cross-threaded.
Recommended Gas Pipe Diameter
Pipe Length Schedule 40 Pipe Tubing, Type L
(Feet) Inside Diameter Outside Diameter
Note: Never use plastic pipe. Check to confirm whether your local codes
allow copper tubing or galvanized.
The installation must conform with local codes or, in the absence of
local codes, with the National Fuel Gas Code ANSI Z223.1*/ Canadian
Installation Code, CAN/CGA-B149.
*Available from the American National Standards Institute, Inc., 11 West
42nd St., New York, NY 10036.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment or
accessories and repair and servicing of equipment shall be performed only
by a qualified agency. The term "qualified agency" means any individual,
firm, corporation or company which whether in person or through a
representative is engaged in and is responsible for (a) the installation or
replacement of gas piping or (b) the connection, installation, repair or
servicing of equipment, who is experienced in such work, familiar with
all precautions required and has complied with all the requirements of
the authority having jurisdiction.
Instruction to Installer
1. Installer must leave instruction manual with owner after
installation.
2. The owner shall retain this instruction manual for future reference.
3. Installer must have owner fill out and mail warranty card supplied
with appliance.
4. Installer should show owner how to start and operate gas grill.
LOCATION REQUIREMENTS
Location (Figure 2 and Figure 3)
When determining a suitable location take into account concerns such as
exposure to wind, proximity to traffic paths and keeping any gas supply
lines as short as possible. Locate the grill only in well ventilated area.
Never locate the grill in a building, garage, breezeway, shed or other such
enclosed areas. During heavy use the grill will produce a lot of smoke.
Ensure that there is adequate area for smoke to dissipate.
• Minimum clearance from sides and back of unit to adjacent com
bustible construction below top of unit, 6 inches from sides and 12
inches from back.
• Minimum horizontal clearance from sides and back of unit to adja
cent vertical combustible construction extending above top of unit,
6 inches from sides and 12 inches from back.
-
-
Page 4R-3848-0-0404
Figure 2
Figure 3
Figure 4
The cardboard box within your grill contains the following parts:
1 box of ceramic plaques (70)
4 grill plates
1 grill plate handle (see page 14, part number 19)
2 elevated cooking racks
1 side burner grate
1 side burner lid
6 burner knobs
1 rotisserie knob
1 chip tray
1 - 5" thermometer for front lid
1 - 2 1/4" thermometer for steamer lid
1 inlet adaptor (LP gas grill only)
1 hose assembly with LP regulator (LP gas grill only)
1 Natural gas regulator (Natural gas grill only)
1 rotisserie rod
1 rotisserie handle
1 counter balance
4 meat forks
1 rotisserie motor
2 rotisserie drip pans
Sequence of Installation of Grill Parts
1. Lay ceramic plaques onto the plaque rack.
2. Place 4 grill plates into grill (flat side or sear side). Your grill plate
handle is used to flip the grill plates to flat side or sear side.
6. Snap 6 burner knobs onto 5 main burner valve stems and onto side
burner valve stem. The inside of a burner knob has a mushroom pat
tern.
7. Snap 1 rotisserie burner knob onto rotisserie burner valve stem. The
inside of the rotisserie burner knob has a 3/4 round pattern.
8. Insert chip tray into grill front between the fourth and fifth main
burner knobs.
9. Insert 5" thermometer into grill lid.
10. Insert 2 1/4" thermometer into steamer lid.
11. For LP gas only, thread brass inlet adaptor onto manifold pipe. Use
teflon tape or a LP gas pipe compound to make a gas tight connection
(see Figure 1).
12. For LP gas only, thread brass fitting from hose assembly onto brass
inlet adaptor (see Figure 1). Tighten completely for a gas tight con
nection.
13. For Natural gas only, thread Natural gas regulator onto manifold pipe.
Use teflon tape or a Natural gas pipe compound to make a gas tight
connection (see Figure 1).
14. Refer to Rotisserie section, page 9 for installation of rotisserie parts
(see Figure 8).
LEAK TESTING
1. Before lighting your grill, check all connections for leaks using a
mild soapy water solution. DO NOT use matches, lighters or flame
to check for leaks, — you could cause an explosion. With the grill
burner controls turned OFF, slowly open the cylinder valve by
turning the handwheel counterclockwise (right to left). Apply mild
soapy water to the connection. If bubbles appear, a leak is indicated.
Do not put the product in service! Immediately close the cylinder
valve handwheel for propane gas or the manual shutoff valve for
natural gas. A qualified service person must be contacted to make
the needed repairs.
2. DO NOT SMOKE WHILE LEAK TESTING!
3. For LP gas (propane) models, leak test with a full propane cylin
der.
-
-
-
R-3848-0-0403Page 5
Loading...
+ 9 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.