Brodware YOKATO 1.9305.05, CITY QUE 1.9805.05, YOKATO 1.9306.05, 1.9913.00, 1.9813.00 Installation Instructions Manual

BASIN AND WALL MIXER
INSTALLATION INSTRUCTIONS

Brodware Industries

2 St James Pl ace
Seven Hill s NSW 2147
Australia
[phone]
brodware.com

FURTHER INFORMATION

For any fur ther information re garding installati on, cleaning
or replac ement components, p lease do not hesitate to call
our customer serv ice on [phone].

IMPORTANT INFORMATION

IMPORTANT

All tapware and

showers to be

installed by a licensed

plumber and to

Australian Standards.

Fit tempering and

pressure reduction

valves where required.

Flush water l ines

before fitment to avoid

damage to valve.

WATE R

TEMPERATURE

Is not to exceed 50ºC

as per AS3500

WATER PRESSURE

Is not to exceed

500kPa as per

AS3500

PRESSURE DIFFERENCE

Hot – Cold water pressure d iffere nce

is not to exceed 150kPa.

This prod uct is desi gned to work on high

pressure systems only.

This unit cannot be used for unpressurised

storage heaters.

SHOWERS

When installing wall showers e nsure that th e male conn ecting

threads do not damage th e flow controller.

CORRECT FUNCTION & MAINTENANCE

CHECK FOR CORRECT

FUNCTION AND

OPERATION

1. Pull lever – open

(water flows)

2. Depress leve r – closed

3. Turn lever clockw ise –

COLD water

4. Turn lever anticloc kwise –

HOT wate r

MAINTENANCE AND

CARE / CARTRIDGE

REPLACEMENT

A. Shut off th e hot and cold water supplies

B. Loosen the socket screw at the back or un derside of the

handle with a 2mm Allen key and pull of f lever han dle

C. Remove the metal cover cap below the lever handle

D. Remove the Hex Locknut be low cover ca p

E. Pull out the car tridge a nd base ‘O’ Ring S eal

F. Replace wi th a genuine Brodware cartrid ge.

Care must be taken to ensure that the lower

‘O’ Ring Seal is located in th e cartr idge correctly.

H

< 150 kPa

C

Brodware.com

A. To comply with Australian

standards, stop cocks are

to be installed below the

tail pipes

B. Fit ‘O’ ring to mixer ba se

C. Fit the optional base ring or

extension if required. This

is not inclu ded as standard

D. Hole size to be Ø3 5mm

except 9301 and 9402

which is Ø32mm

Lower mi xer into basin

or counter top

E. Fit the metal was her to

underside of basin or

counte r top

F. Fit the brass n ut to stud

and tighten mixer into it’s

correct position

G. Che ck for leaks, ensure

the swivel s pout is secured

with a screw

INSTALLATION BASIN OR SINK MIXER

B.A. C.

E. F.D. G.

When installing the mixer,
ensure that it is positioned
correctly, with the mixer o n the
top side and the diver ter on
the bottom side.

Hot water is connected to
the left, and the cold water is
connected to the right, when
viewed from the operating
position.

When the diverter handle is
rotated fully clock wise, water
is diver ted to the bottom p ort.

Anti-clockwis e rotation of the
handle diverts wate r to the
top port.

1.XX48.05 DIVERTOR / MIXER
INSTALLATION GUIDE

cold

holes

bottom port

top port

hot

diverter

handle

ICNMIX | B R3367 | 0816

ALL PLUMB ING MUS T BE TESTE D BEFORE

CONCE ALING / S HEETIN G OFF AS PER A S350 0

Brodware.com

To be read in conj unction
with wall mixer information.

A. Seal and f it plug.

B. Fit and seal nipple th en

tighten nuts.

C. Trial fit the wall pl ate

and ensure centre of mixer
to nipple is correct an d
level before sheeting off.

D. Fix backing pl ate to wall.

E. Cut the nipple th read

to length before fitti ng
wall plate.

F. Tile or finish wall face.

G. Cit y Que 1.9805.05.

Plate to fit bac k to the
shoulder of the nipple.

Yokato 1.9305.05.

The nipple screws in from
the front. Sc rew in till it
bottoms ou t on the plate.

H. When fitting off lock handle

and spout screws with
allen key supplied.

To be read in conjunction
with information on reverse.

Using

copper tubes
supplied, rough in supply lines.
Use the template supplied to
ensure the correct spacing
of tubes.

The tubes are to be clean
and smooth with no external
damage, with the top of
the tubes clean cut and
no extern al burrs. Ensure
protection of tubes during
building works.

The structure is to be suf ficient
to securel y anchor the mixer
and tubes.

When fitting off drill flo or for
fixing s, ensure wate r lines
are flushed to remove foreign
particles. Push on flexible
connectors to supply tubes.

Supply tu bes to be 25-30 mm
above finished flo or.

Water test before fixing d own.
Remote isolating valve s must

be fitted to enable ea se of
service if required.

If the floo r is not level, the
adjustment screws in the floor
mount can be adjusted to
ensure the mixer is ver tical.

Screw down dress flange.

These in struct ions are t o be read in
conjunction with the basic installation card.

1. Using

copper tubes supplied, rough in
supply lines. Use the template supplied to
ensure the correct spacing of tub es.

2. The tubes are to be clean and smooth w ith
no extern al damage, with the top of the tubes
clean cu t and no external burr s. Ensure
protection of tubes during building works.

3. The structure is to be suf ficient to secure ly
anchor th e mixer and tu bes.

5. When fitting off drill flo or for fixings, ensure
water lines are flushed to remove any fo reign
particles. Push on flexible connectors to
supply tubes. Supply tubes to be 25-30mm
above finished flo or and centered 75mm
from wall.

6. Water test before fixing d own.

Remote isolating valve s must be fi tted to enab le
ease of ser vice if required.

If the floo r is not level, the adjustme nt screws in
the floor mount can be adjusted to en sure the
mixer is ver tical.

Screw down dress flange.

WALL MIXER INSTALLATION CITY QUE 1.9805.05, YOKATO 1.9305.05 AND 1.9306.05

WALL MIXER INSTALLATION

FLOOR MOUNTED BATH / BASIN MIXER
INSTALLATION GUIDE

1.9913.0 0 AND 1.9813.00

FLOOR MOUNTED SHOWER
INSTALLATION GUIDE

A

B

Front View

C

D

E

F

GH

Side View

A. Remove the handle and trim and push protecti ve sleeve over

the body to protect from damage during tiling.

B. Install mixer to correct depth as sh own in the draw ing.

It is most important that the finished wall location is
determined.

Base of body to fin ished wa ll face (Le ngth B)

Product Ma x Min

1.9348.00 70mm 45mm

1.9448.00 60mm 45mm
All other innwall mixers 77mm 45mm

When i nstalling the mixer ensure that it i s positioned the

correct way (as per the markings on the body) with the hot
water on the left and cold water on the ri ght when viewed
from an operating position.

Connect mixer using union connections (not nylon olives).

Ensure mixer is level and aligned c orrectly.

C. Because of the speed at wh ich singl e lever mixers can be

closed, th ey can acce ntuate water ha mmer if not properly
installed. Before sheeting walls it is impor tant that the system
is checked for this.

If hammer is apparent, all pos sible measures are to be taken,

includi ng but not lim ited to, correc t and secure fixing of
pipework, keeping th e length of the pipework o n the outlet as
short a s possibl e and the fit ting of outl ets that have a hi gh star
rating

D. Check ope ration and te st for leaks before plastering or tiling

and refit tiling sleeve. Seal around bodies to prevent water
penetration into wall

E. On completion of tiling rem ove tiling sleeve and fit dress ring.

Fit handle and secure with grub s crew

Length BFinished

Wall

A.

B.

D. E.

C.

Mixer

Dress flange

Alan key

4x Fixing bolts

Floor mount

4x Leveling grub screws

25-35mm above finished floor

Copper tubes

Finished wall to be 75mm
from centre of water inlets

Connects

Key

4x Fixing

Bolts

Brass Flange

Mixer

4x Levelling
Grub Screws

Floor Mount

Connects

Copper Tubes

25-30mm above
finished floor