Brocade Communications Systems DS-5100B - Connectrix Switch - 8Gb Fibre Channel, 5100 Hardware Reference Manual

Download

Page 1

53-1000854-02 July 18, 2008

Brocade 5100

Hardware Reference Manual

Page 2

Brocade, Fabric OS, File Lifecycle Manager, MyView, and StorageX are registered trademarks and the Brocade B-wing symbol, DCX, and SAN Health are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with respect to any loss, cost, liability, or damages arising from the information contained in this book or the computer programs that accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other open source license agreements. To find-out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd.

Brocade Communications Systems, Incorporated

Corporate Headquarters Brocade Communications Systems, Inc. 1745 Technology Drive San Jose, CA 95110 Tel: 1-408-333-8000 Fax: 1-408-333-8101 Email: info@brocade.com

European and Latin American Headquarters Brocade Communications Switzerland Sàrl Centre Swissair Tour A - 2ème étage 29, Route de l'Aéroport Case Postale 105 CH-1215 Genève 15 Switzerland Tel: +41 22 799 56 40 Fax: +41 22 799 56 41 Email: emea-info@brocade.com

Asia-Pacific Headquarters Brocade Communications Singapore Pte. Ltd. 9 Raffles Place #59-02 Republic Plaza 1 Singapore 048619 Tel: +65-6538-4700 Fax: +65-6538-0302 Email: apac-info@brocade.com

Document History

Title Publication Number Summary of Changes Date

Brocade 5100 Hardware Reference Manual 53-1000854-01 New document March 2008

Brocade 5100 Hardware Reference Manual 53-1000854-02 Document update July 2008

Page 3

Contents

About This Document

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Supported hardware and software . . . . . . . . . . . . . . . . . . . . . . . . . . vii

What’s new in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Document conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Getting technical help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Chapter 1 Brocade 5100 Introduction

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Brocade 5100 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Port side of the Brocade 5100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Non-port side of the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Field replaceable units (FRUs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Ports on Demand license . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ISL trunking groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2 Brocade 5100 Installation and Configuration

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Items included with the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation and safety considerations. . . . . . . . . . . . . . . . . . . . . . . . . 7

Electrical considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Environmental considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cabinet considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Recommendations for cable management . . . . . . . . . . . . . . . . . 8

Items required for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing a standalone Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . 9

Cabinet installation for a Brocade 5100 . . . . . . . . . . . . . . . . . . . . . .10

Brocade 5100 Hardware Reference Manual iii 53-1000854-02

Page 4

Brocade 5100 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Providing power to the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Creating a serial connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Switch IP address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Date and time settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Chapter 3 Brocade 5100 Operation

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Powering the Brocade 5100 on and off. . . . . . . . . . . . . . . . . . . . . . .17

LED activity interpretation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Brocade 5100 LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LED locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

LED Patterns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

POST and boot specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Interpreting POST results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Maintaining the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Installing an SFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Diagnostic tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Field Replaceable Units (FRUs). . . . . . . . . . . . . . . . . . . . . . . . . .23

Power supply/fan assembly FRU replacement . . . . . . . . . . . . .23

Managing the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Appendix A Brocade 5100 Specifications

In this appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Switch components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Weight and physical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Facility requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Power supply specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Environmental requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

General specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Data transmission ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Memory specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Fibre Channel port specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Serial port specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

iv Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 5

Index

Regulatory compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

FCC warning (US only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

MIC statement (Republic of Korea) . . . . . . . . . . . . . . . . . . . . . .33

VCCI statement Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Power cords (Japan Denan). . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

BSMI statement (Taiwan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

CE statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Canadian requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Laser compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

RTC battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Regulatory certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Environmental regulation compliance. . . . . . . . . . . . . . . . . . . . . . . .36

China RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Brocade 5100 Hardware Reference Manual v 53-1000854-02

Page 6

vi Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 7

About This Document

In this chapter

•How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

•Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

•What’s new in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

•Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

•Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

•Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

•Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

•Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

How this document is organized

This document is organized to help you find the information that you want as quickly and easily as possible.

The document contains the following components:

• Chapter 1, “Brocade 5100 Introduction,” provides an overview of the Brocade 5100 switch, a

feature list, and a look at the appearance of the switch.

• Chapter 2, “Brocade 5100 Installation and Configuration,” provides the information needed to

install the switch into your network.

• Chapter 3, “Brocade 5100 Operation,” discusses the day-to-day operational procedures for

using the switch.

• Appendix A, “Brocade 5100 Specifications,” provides tables of physical, environmental, and

general specifications, helpful for quick lookup.

• The index points you to the exact pages on which specific information is located.

Supported hardware and software

Although many different software and hardware configurations are tested and supported by Brocade Communications Systems, Inc. for Fabric OS v6.1.0, documenting all possible configurations and scenarios is beyond the scope of this document.

This document is specific to the Brocade 5100 and Fabric OS v6.1.0. To obtain information about a Fabric OS version other than v6.1.0, see the documentation specific to that OS version.

Brocade 5100 Hardware Reference Manual vii 53-1000854-02

Page 8

What’s new in this document

Corrections have been made to the original document.

Document conventions

This section describes text formatting conventions and important notice formats used in this document.

Text formatting

The narrative-text formatting conventions that are used are as follows:

bold text Identifies command names

Identifies the names of user-manipulated GUI elements Identifies keywords and operands Identifies text to enter at the GUI or CLI

italic text Provides emphasis

Identifies variables Identifies paths and Internet addresses Identifies document titles

code text Identifies CLI output

Identifies command syntax examples

For readability, command names in the narrative portions of this guide are presented in mixed lettercase: for example, switchShow. In actual examples, command lettercase is often all lowercase. Otherwise, this manual specifically notes those cases in which a command is case sensitive.

Command syntax conventions

Command syntax in this manual follows these conventions:

command Commands are printed in bold.

--option, option Command options are printed in bold.

-argument, arg Arguments.

[ ] Optional element.

variable Variables are printed in italics. In the help pages, values are underlined

enclosed in angled brackets < >.

... Repeat the previous element, for example “member[;member...]”

value Fixed values following arguments are printed in plain font. For example,

--show WWN

| Boolean. Elements are exclusive. Example:

viii Brocade 5100 Hardware Reference Manual

--show -mode egress | ingress

53-1000854-02

Page 9

Notes, cautions, and warnings

The following notices and statements are used in this manual. They are listed below in order of increasing severity of potential hazards.

NOTE

A note provides a tip, guidance or advice, emphasizes important information, or provides a reference to related information.

ATTENTION

An Attention statement indicates potential damage to hardware or data.

CAUTION

A Caution statement alerts you to situations that can be potentially hazardous to you.

DANGER

A Danger statement indicates conditions or situations that can be potentially lethal or extremely hazardous to you. Safety labels are also attached directly to products to warn of these conditions or situations.

Key terms

For definitions specific to Brocade and Fibre Channel, see the Brocade Glossary.

For definitions of SAN-specific terms, visit the Storage Networking Industry Association online dictionary at:

http://www.snia.org/education/dictionary

Notice to the reader

This document may contain references to the trademarks of the following corporations. These trademarks are the properties of their respective companies and corporations.

These references are made for informational purposes only.

Corporation Referenced Trademarks and Products

IBM Corporation IBM, FICON, PowerPC

Additional information

This section lists additional Brocade and industry-specific documentation that you might find helpful.

Brocade 5100 Hardware Reference Manual ix 53-1000854-02

Page 10

Brocade resources

To get up-to-the-minute information, join Brocade Connect. It’s free! Go to http://www.brocade.com and click Brocade Connect to register at no cost for a user ID and password.

For practical discussions about SAN design, implementation, and maintenance, you can obtain

Building SANs with Brocade Fabric Switches through:

http://www.amazon.com

For additional Brocade documentation, visit the Brocade SAN Info Center and click the Resource Library location:

http://www.brocade.com

Release notes are available on the Brocade Connect Web site and are also bundled with the Fabric OS firmware.

Other industry resources

• White papers, online demos, and data sheets are available through the Brocade Web site at

http://www.brocade.com/products/software.jhtml.

• Best practice guides, white papers, data sheets, and other documentation is available through

the Brocade Partner Web site.

For additional resource information, visit the Technical Committee T11 Web site. This Web site provides interface standards for high-performance and mass storage applications for Fibre Channel, storage management, and other applications:

http://www.t11.org

For information about the Fibre Channel industry, visit the Fibre Channel Industry Association Web site:

http://www.fibrechannel.org

Getting technical help

Contact your switch support supplier for hardware, firmware, and software support, including product repairs and part ordering. To expedite your call, have the following information available:

1. General Information

• Switch model

• Switch operating system version

• Error numbers and messages received

• supportSave command output

• Detailed description of the problem, including the switch or fabric behavior immediately

following the problem, and specific questions

• Description of any troubleshooting steps already performed and the results

• Serial console and Telnet session logs

• syslog message logs

x Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 11

2. Switch Serial Number

The switch serial number and corresponding bar code are provided on the serial number label, as illustrated below.:

*FT00X0054E9*

FT00X0054E9

The serial number label is located as follows:

• Brocade 200E—On the non-port side of the chassis

• Brocade 300, 4100, 4900, 5100, 5300, 7500, and Brocade Encryption Switch—On the

switch ID pull-out tab located inside the chassis on the port side on the left

• Brocade 5000—On the switch ID pull-out tab located on the bottom of the port side of the

switch

• Brocade 7600—On the bottom of the chassis

• Brocade 48000—Inside the chassis next to the power supply bays

• Brocade DCX—On the bottom right on the port side of the chassis

3. World Wide Name (WWN)

Use the wwn command to display the switch WWN.

If you cannot use the wwn command because the switch is inoperable, you can get the WWN from the same place as the serial number, except for the Brocade DCX. For the Brocade DCX, access the numbers on the WWN cards by removing the Brocade logo plate at the top of the non-port side of the chassis.

Document feedback

Quality is our first concern at Brocade and we have made every effort to ensure the accuracy and completeness of this document. However, if you find an error or an omission, or you think that a topic needs further development, we want to hear from you. Forward your feedback to:

documentation@brocade.com

Provide the title and version number of the document and as much detail as possible about your comment, including the topic heading and page number and your suggestions for improvement.

Brocade 5100 Hardware Reference Manual xi 53-1000854-02

Page 12

xii Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 13

Chapter

Brocade 5100 Introduction

In this chapter

•Brocade 5100 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

•Port side of the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

•Non-port side of the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

•Field replaceable units (FRUs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

•Ports on Demand license . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

•ISL trunking groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Brocade 5100 overview

The Brocade 5100 is an Enterprise class 1U, 40-port Fibre Channel 1, 2, 4 or 8 Gbps Fibre Channel switch that offers the next generation Brocade, single-chip architecture for Storage Area Networks (SANs). The Brocade 5100 is designed to function in large-scale enterprise SANs and can also fit the requirements of small to medium-sized work groups.

Because the Brocade 5100 has a slim 1U height and a high port count, you can use the Brocade 5100 to create very dense fabrics in a relatively small space. With its flexible Ports On Demand (POD) capability, the Brocade 5100 provides excellent overall value as the foundation of a SAN with the ability to grow with an organization’s SAN needs.

The Brocade 5100 is the latest mid-range offer from the Brocade family of entry-to-enterprise products. It supports the following features:

• Up to 40 ports of high-performance 8 Gbps technology and POD scaling from 24 to 32 or 40

ports.

• Support for 1, 2, 4, and 8 Gbps auto-sensing Fibre Channel switch and router ports.

• FICON

, FICON Cascading and FICON Control Unit Port ready.

• Two hot-swappable, redundant integrated power supply and fan FRUs.

• Universal ports that self-configure as E, F, M, or FL ports. Ex_Ports are activated on a per port

basis with the optional Integrated Routing license.

• Fibre Channel Routing (FCR) service that provides improved scalability and fault isolation

(through the optional Integrated Routing license).

• An RJ45 Ethernet management port, that in conjunction with EZSwitchSetup, supports switch

IP address discovery and configuration, eliminating the need to attach a serial cable to configure the switch IP address and greatly increasing the ease of use.

• USB port that provides storage for firmware updates, output of the supportSave command and

storage for configuration uploads and downloads

• Single motherboard design with 667 MHz PowerPC 440EPx Reduced Instruction Set Computer

(RISC) CPU and integrated peripherals which provide high performance.

Brocade 5100 Hardware Reference Manual 1 53-1000854-02

Page 14

Port side of the Brocade 5100

• Inter-Switch Link (ISL) Trunking (licensable), which allows up to eight ports (at 1, 2, 4, or 8 Gbps

• Dynamic Path Selection (DPS), which optimizes fabric-wide performance and load balancing by

• Rack-mount design using existing rail kits (fixed, sliding, and mid-mount/Telco rail kits) on a

• Industry-leading extended distance support, which enables native Fibre Channel extension

• Expanded security for up to 16,000 hardware zones. Hardware zoning is accomplished at the

• Unicast, multicast (255 groups), and broadcast data traffic type, are support.

• Brocade Small Form-Factor Pluggable (SFP) or SFP+ optical transceivers support any

• Brocade Fabric Operating System (Fabric OS), which delivers distributed intelligence

• Port-to-port latency minimized to 700 nanoseconds through the use of cut-through frame

• Extensive diagnostics and system monitoring capabilities, which enhance high Reliability,

• The Brocade EZSwitchSetup wizard, which makes SAN configuration a three-step point-and

speeds) between a pair of switches combined to form a single, logical ISL with a speed of up to 128 Gbps full duplex for optimal bandwidth utilization and load balancing.

automatically routing data to the most efficient available path in the fabric.

19” EIA rack.

greater than 590 km.

port level of the switch or by World Wide Name (WWN). Hardware zoning permits or denies delivery of frames to any destination port address.

combination of Short Wavelength (SWL), Long Wavelength (LWL) or Extended Long Wavelength (ELWL) optical media among the switch ports.

throughout the network and enables a wide range of value-added applications including Brocade Advanced Web Tools and Brocade Zoning. Optional Fabric Services include: Adaptive Networking with QoS, Brocade Extended Fabrics, Brocade Enhanced Group Management, Brocade Fabric Watch, ISL Trunking, Integrated Routing, and End-to-End Performance Monitoring (APM).

routing at 8 Gbps.

Availability, and Serviceability (RAS).

click task.

Port side of the Brocade 5100

The port side of the Brocade 5100 includes the system status LED, console port, Ethernet port and LEDs, USB port, and Fibre Channel ports and the corresponding port status LEDs.

Figure 1 shows the port side of the Brocade 5100.

2 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 15

Port side of the Brocade 5100

8 9 10 11

12 13 14 15

0 1 2 3 8 9 10 11

18 19

24 25 26 27

32 33 34 35

4 5 6 7 12 13 14 15 20

22 23

28 29 30 31

37 38 39

3 5

0123 891011 16171819 24252627 32333435

4567 12131415 20212223 28293031 36373839

1 System status (top) and power (bottom) LEDs

2 System RS232 console port (RJ-45)

3 System Ethernet port (RJ-45)

4 Ethernet port LEDs (green/amber)

5USB port

6 Fibre Channel port status LED

7Fibre Channel ports

8 Switch ID pull-out tab

FIGURE 1 Port-side view of the Brocade 5100

Port Numbering

The Fibre Channel ports on the Brocade 5100 are numbered from left to right, in eight-port groups from 0 to 39 as illustrated in Figure 2.

Brocade 5100 Hardware Reference Manual 3

53-1000854-02

FIGURE 2 Port Numbering on the Brocade 5100

Page 16

Non-port side of the Brocade 5100

ATTENTION

Brocade ISL Trunking is licensed sof tware that allows you to create trunking groups of ISLs between adjacent switches. For more information about Brocade ISL Trunking, refer to the Brocade Fabric OS Administrator’s Guide.

Non-port side of the Brocade 5100

The non-port side of the Brocade 5100 includes the two redundant power supply-fan assemblies and the corresponding status LEDs.

Figure 3 shows the port side of the Brocade 5100.

1 4 85

2 6

1 Fan (for power supply/fan FRU2)

2 Power supply/Fan status LED (for power supply/fan FRU 2)

3 Power supply connector (for power supply/fan FRU2)

4 Fan (for power supply/fan FRU2)

5 Fan (for power supply/fan FRU1)

6 Power supply/Fan status LED (for Power Supply/fan FRU 1)

7 Power supply connector (for power supply/fan FRU 1)

8 Fan (for power supply/fan FRU1)

3 7

FIGURE 3 Non-port side view of the Brocade 5100

Field replaceable units (FRUs)

The Brocade 5100 has two integrated power supply and fan unit field replaceable units (FRUs). These power supply/fan assembly units are hot-swappable and redundant, and are capable of functioning universally without voltage jumpers or switches. The FRU units are identical and interchangeable.

The front panel has a status LED that provides the status of the entire switch, including the two power supply/fan assembly FRUs.

4 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 17

Ports on Demand license

The Brocade 5100 has 40 ports. By default, ports 0-24 are enabled. To enable additional ports, you must install Ports On Demand (POD) licenses.

To install a POD license, you can either use the supplied license key or generate a license key. Typically the switch is shipped with a paper pack that specifies the transaction key to use with the Software License Keys link. Use this transaction key on the Brocade Web site at www.brocade.com/licensekeys and follow the instructions to generate the key. You can also use this site to generate other license keys for your switch.

After you have installed the license keys, you must enable the ports. You can do so without disrupting switch operation by using the portEnable command on each port individually. Alternatively, you can disable and re-enable the switch to activate all ports simultaneously.

For detailed information on enabling additional ports using the POD license, refer to the Fabric OS Administrator’s Guide.

ISL trunking groups

Ports on Demand license

The Brocade 5100 supports Interswitch Link (ISL) Trunking as a licensed feature. When this feature is enabled, you can create trunked groups of up to eight contiguous ports, permitting a speed of up to 64 Gbps (128 Gbps full duplex).

NOTE

Brocade 5100 Hardware Reference Manual 5 53-1000854-02

Page 18

ISL trunking groups

6 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 19

Chapter

Brocade 5100 Installation and Configuration

In this chapter

•Items included with the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

•Installation and safety considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

•Installing a standalone Brocade 5100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

•Cabinet installation for a Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

•Brocade 5100 configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Items included with the Brocade 5100

The following items are included with the standard shipment of the Brocade 5100. When you open the Brocade 5100 packaging, verify that these items are included in the package and that no damage has occurred during shipping:

• The Brocade 5100 switch, containing two power supply/fan assembly units

• One accessory kit containing:

• Serial Cable with an RJ-45 connector

• 6 ft. Power Cord

• Rubber feet, required for setting up the switch as a standalone unit

• Brocade Family Doc CD

• Brocade 5100 QuickStart Guide

• EZSwitchSetup CD

Installation and safety considerations

You can install the Brocade 5100 switch in the following ways:

1. As a standalone unit on a flat surface.

2. In an EIA cabinet using a fixed-rail rack mount kit. The optional fixed-rail rack mount kit can be ordered from your switch retailer.

3. In an EIA cabinet using an optional slide-rail rack mount kit. The optional slide-rail rack mount kit can be ordered from your switch retailer. When mounting into a slide-rail rack, you can mount the chassis to slide from either the port side or the non-port side.

4. In an EIA cabinet using an optional mid-mount rack kit for switches. The optional mid-mount rack kit for switches can be ordered from your switch retailer.

Brocade 5100 Hardware Reference Manual 7 53-1000854-02

Page 20

Installation and safety considerations

Electrical considerations

To install and operate the switch successfully, ensure the following:

• The primary outlet is correctly wired, protected by a circuit breaker, and grounded in

accordance with local electrical codes.

• The supply circuit, line fusing, and wire size are adequate, as specified by the electrical rating

on the switch nameplate.

• The power supply standards provided in Table 5, “Power Supply Specifications” on page 28 are

met.

Environmental considerations

For successful installation and operation of the switch, ensure that the following environmental requirements are met:

• At a minimum, adequate cooling requires that you install the switch with the non-port side,

which contains the air intake vents, facing the cool-air aisle.

• All equipment in the rack should force air in the same direction to avoid intake of exhaust

air.

• A maximum of 49.3 cubic meters/hour (29 cubic feet/minute) and a minimum of 37.4

cubic meters/hour (22 cubic feet/minute) of air flow is available to the air intake vents on the non-port side of the switch.

• The ambient air temperature does not exceed 40° C (104° F) while the switch is operating.

Cabinet considerations

For successful installation and operation of the switch in a cabinet, ensure the following cabinet requirements are met:

• The cabinet must be a standard EIA cabinet.

• Plan a cabinet space that is one rack unit (1U) high; 4.45 cm (1.75 inches) and 48.3 cm

(19 inches) wide.

• Ground all equipment in the cabinet through a reliable branch circuit connection and

maintain ground at all times. Do not rely on a secondary connection to a branch circuit, such as a power strip.

• Ensure that airflow and temperature requirements are met on an ongoing basis,

particularly if the switch is installed in a closed or multicabinet assembly.

• Verify that the additional weight of the switch does not exceed the cabinet’s weight limits

or unbalance the cabinet in any way.

• Secure the cabinet to ensure stability in case of unexpected movement, such as an

earthquake.

Recommendations for cable management

The minimum bend radius for a 50 micron cable is 2 inches under full tensile load and 1.2 inches with no tensile load.

8 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 21

Installing a standalone Brocade 5100

Cables can be organized and managed in a variety of ways, for example, using cable channels on the sides of the cabinet or patch panels to minimize cable management. Following is a list of recommendations:

NOTE

You should not use tie wraps with optical cables because they are easy to over tighten.

• Plan for rack space required for cable management before installing the switch.

• Leave at least 1 m (3.28 ft) of slack for each port cable. This provides room to remove and

replace the switch, allows for inadvertent movement of the rack, and helps prevent the cables from being bent to less than the minimum bend radius.

• If you are using Brocade ISL Trunking, consider grouping cables by trunking groups. The

cables used in trunking groups must meet specific requirements, as described in the Fabric OS Administrator’s Guide.

• For easier maintenance, label the fiber optic cables and record the devices to which they

are connected.

• Keep LEDs visible by routing port cables and other cables away from the LEDs.

• Use hook and loop style straps to secure and organize fiber optic cables.

Items required for installation

The following items are required for installing, configuring, and connecting the Brocade 5100 for use in a network and fabric:

• Workstation with an installed terminal emulator, such as HyperTerminal

• Unused IP address and corresponding subnet mask and gateway address

• Serial cable (provided)

• Ethernet cable

• SFPs and compatible cables, as required

• Access to an FTP server for backing up the switch configuration (optional)

Installing a standalone Brocade 5100

Perform this task to install the Brocade 5100 as a standalone unit.

1. Unpack the Brocade 5100 and verify the items listed on “Items included with the Brocade

5100” on page 7. Verify the items are present and undamaged.

2. Apply the adhesive rubber feet. Applying the rubber feet onto the switch helps prevent the switch from sliding off the supporting surface.

a. Clean the indentations at each corner of the bottom of the switch to ensure that they are

free of dust or other debris that might lessen the adhesion of the feet.

b. With the adhesive side against the chassis, place one rubber foot in each indentation and

press into place.

3. Place the switch on a flat, sturdy surface.

4. Provide power to the switch as described in “Providing power to the switch” on page 10.

Brocade 5100 Hardware Reference Manual 9 53-1000854-02

Page 22

Cabinet installation for a Brocade 5100

ATTENTION

Do not connect the switch to the network until the IP address is correctly set. For instructions on how to set the IP address, see “Brocade 5100 configuration”

Cabinet installation for a Brocade 5100

You must use one of three rack mount kits to install a Brocade 5100 in a cabinet. A rack mount kit can be installed in two ways:

• To allow the port side of the switch to slide out of the exhaust-air side of the cabinet.

In this installation, the port side of the switch is flush with the edge of the cabinet.

• To allow the non-port side of the switch to slide out the cool-air side of the cabinet.

In this installation, the port side of the switch is set 7.62 cm (3 inches) back from the edge of the cabinet, allowing a more gradual bend in the fiber optic cables.

Whichever mounting method you choose, follow the installation instructions shipped with the appropriate rack mount kit:

• To install the switch into a fixed-rail rack, refer to the Fixed Rack Mount Kit Installation

Procedure.

• To install the switch into a slide-rail rack, refer to the Slide Rack Mount Kit Installation

Procedure.

• To install the switch into mid-mount rack, refer to the Mid-Mount Rack Mount Kit (Switch)

Installation Procedure.

Brocade 5100 configuration

Once you have set up the Brocade 5100 in a rack or as a standalone switch, it is time to give it power and a basic configuration. If you are going to use the Brocade 5100 in a single-switch setup, you can use EZSwitchSetup to complete the basic configuration.

See the EZSwitchSetup CD, included with the Brocade 5100 for more information. You can also use the Brocade 5100 Quick Start Guide.

If you do not want to use EZSwitchSetup, follow the instructions in the rest of this section.

Providing power to the switch

Perform the following steps to provide power to the Brocade 5100.

1. Connect the power cords to both power supplies, and then to power sources on separate circuits to protect against AC failure. Ensure that the cords have a minimum service loop of 6 in. available and are routed to avoid stress.

2. Power on the power supplies by flipping both AC switches to the “1” symbol. The power supply LEDs display amber until POST is complete, and then change to green. The switch usually requires from 1 to 3 min to boot and complete POST.

ATTENTION

Power is supplied to the switch as soon as the first power supply is connected and turned on.

10 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 23

Brocade 5100 configuration

3. After POST is complete, verify that the switch power and status LEDs on the left of the port side of the switch are green.

Creating a serial connection

You will perform all basic configuration tasks in this guide using a serial connection.

Complete the following steps to create a serial connection to the switch.

1. Connect the serial cable to the serial port on the switch and to an RS-232 serial port on the workstation.

If the serial port on the workstation is RJ-45 instead of RS-232, remove the adapter on the end of the serial cable and insert the exposed RJ-45 connector into the RJ-45 serial port on the workstation.

2. Open a terminal emulator application (such as HyperTerminal on a PC, or TERM, TIP, or Kermit in a UNIX environment), and configure the application as follows:

• In a Windows environment:

Parameter Value

Bits per second 9600

Databits 8

Parity None

Stop bits 1

Flow control None

• In a UNIX environment, enter the following string at the prompt:

tip /dev/ttyb -9600

If ttyb is already in use, use ttya instead and enter the following string at the prompt:

tip /dev/ttya -9600

Switch IP address

You can configure the Brocade 5100 with a static IP address, or you can use a DHCP (Dynamic Host Configuration Protocol) server to set the IP address of the switch. DHCP is enabled by default. The Brocade 5100 supports both IPv4 and IPv6.

Using DHCP to set the IP address

When using DHCP, the Brocade 5100 obtains its IP address, subnet mask, and default gateway address from the DHCP server. The DHCP client can only connect to a DHCP server that is on the same subnet as the switch. If your DHCP server is not on the same subnet as the Brocade 5100, use a static IP address.

Setting a static IP address

Perform the following steps to set a static IP address on the switch.

Brocade 5100 Hardware Reference Manual 11 53-1000854-02

Page 24

Brocade 5100 configuration

1. Log into the switch using the default password, which is password.

2. Use the ipaddrset command to set the Ethernet IP address.

3. Complete the rest of the network information as prompted.

4. Enter off to Disable DHCP when prompted.

If you are going to use an IPv4 IP address, enter the IP address in dotted decimal notation as prompted.

Ethernet IP Address: [192.168.74.102]

If you are going to use an IPv6 address, enter the network information in semicolon-separated notation as prompted.

switch:admin> ipaddrset -ipv6 --add 1080::8:800:200C:417A/64 IP address is being changed...Done.

Ethernet Subnetmask: [255.255.255.0]

Ethernet IP Address: [192.168.74.102] Ethernet Subnetmask: [255.255.255.0]

DHCP [OFF]: off

Date and time settings

The Brocade 5100 maintains the current date and time inside a battery-backed real-time clock (RTC) circuit. Date and time are used for logging events. Switch operation does not depend on the date and time; a Brocade 5100 with an incorrect date and time value still functions properly. However, because the date and time are used for logging, error detection, and troubleshooting, you should set them correctly.

Time zones

You can set the time zone for the switch by name. You can also set country, city or time zone parameters.

If the time zone is not set with the new options, the switch retains the offset time zone settings. The tsTimeZone command includes an option to revert to the prior time zone format. For more information about the

You can set the time zone for a switch using the tsTimeZone command. The tsTimeZone command allows you to perform the following tasks:

• Display all of the time zones supported in the firmware

• Set the time zone based on a country and city combination or based on a time zone ID such as

PST

The time zone setting has the following characteristics:

• You can view the time zone settings. However, only those with administrative permissions can

set the time zones.

• The tsTimeZone setting automatically adjusts for Daylight Savings Time.

• Changing the time zone on a switch updates the local time zone setup and is reflected in local

time calculations.

• By default, all switches are in the GMT time zone (0,0). If all switches in a fabric are in one time

zone, it is possible for you to keep the time zone setup at the default setting.

--old option, see the Fabric OS Command Reference Manual.

12 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 25

Brocade 5100 configuration

• System services that have already started will reflect the time zone changes only after the next

reboot.

• Time zone settings persist across failover for high availability.

Local time synchronization

You can synchronize the local time of the principal or primary fabric configuration server (FCS) switch to a maximum of eight external network time protocol (NTP) servers. To keep the time in your SAN current, it is recommended that the principal or primary FCS switch has its time synchronized with at least one external NTP server. The other switches in the fabric will automatically take their time from the principal or primary FCS switch.

All switches in the fabric maintain the current clock server value in non-volatile memory. By default, this value is the local clock server <LOCL> of the principal or primary FCS switch. Changes to the clock server value on the principal or primary FCS switch are propagated to all switches in the fabric.

When a new switch enters the fabric, the time server daemon of the principal or primary FCS switch sends out the addresses of all existing clock servers and the time to the new switch. If a switch with v5.3.0 or later has entered the fabric it will be able to store the list and the active servers; pre-5.3.0 Fabric OS switches will ignore the new list parameter in the payload and will update only the active server address.

If the active NTP server configured is IPv6, then distributing the same in the fabric will not be possible to switches earlier than v5.3.0 because IPv6 is supported for Fabric OS version 5.3.0 and later. The default value LOCL will be distributed to pre-5.3.0 switches.

The tsClockServer command accepts multiple server addresses in either IPv4, IPv6, or DNS name formats. When multiple NTP server addresses are passed, tsclockserver sets the first obtainable address as the active NTP server. The rest are stored as backup servers that can take over if the active NTP server fails. The principal or primary FCS switch synchronizes its time with the NTP server every 64 seconds.

Setting the date

Perform the following steps to set the date on the switch.

1. Log into the switch using the default password, which is password.

2. Enter the date command, using the following syntax:

date "mmddHHMMyy"

The values are:

• mm is the month; valid values are 01 through 12.

• dd is the date; valid values are 01 through 31.

• HH is the hour; valid values are 00 through 23.

• MM is minutes; valid values are 00 through 59.

• yy is the year; valid values are 00 through 99 (values greater than 69 are interpreted as

1970 through 1999, and values less than 70 are interpreted as 2000-2069).

switch:admin> date Fri Sep 29 17:01:48 UTC 2007 switch:admin> date "0927123007"

Brocade 5100 Hardware Reference Manual 13 53-1000854-02

Page 26

Brocade 5100 configuration

Setting time zones

You must perform the procedure on all switches for which the time zone must be set. However, you only need to set the time zone once on each switch, because the value is written to nonvolatile memory.

Use one of the two following procedures to set the time zone.

The following procedure describes how to set the current time zone using timezone_fmt mode to Central Standard time.

1. Log into the switch using the default password, which is password.

2. Enter the tsTimeZone command as follows:

Thu Sep 27 12:30:00 UTC 2007 switch:admin>

switch:admin> tstimezone [--interactive]/ [, timezone_fmt]

Use timezone_fmt to set the time zone by Country/City or by time zone ID, such as PST.

The following example shows how to change the time zone to US/Central.

switch:admin> tstimezone Time Zone : US/Pacific switch:admin> tstimezone US/Central switch:admin> tstimezone Time Zone : US/Central

The following procedure describes how to set the current time zone using interactive mode to Pacific Standard Time.

1. Type the tsTimeZone command as follows:

switch:admin> tstimezone --interactive

2. You are prompted to select a general location.

Please identify a location so that time zone rules can be set correctly.

3. Enter the appropriate number or Ctrl-D to quit.

4. At the prompt, select a country location.

5. At the prompt, enter the appropriate number to specify the time zone region or Ctrl-D to quit.

Synchronizing local time using NTP

Perform the following steps to synchronize the local time using NTP.

1. Log into the switch using the default password, which is password.

2. Enter the tsClockServer command:

switch:admin> tsclockserver "<ntp1;ntp2>"

where ntp1 is the IP address or DNS name of the first NTP server, which the switch must be able to access. The second ntp2 is the second NTP server and is optional. The operand “<ntp1;ntp2>” is optional; by default, this value is LOCL, which uses the local clock of the principal or primary switch as the clock server.

switch:admin> tsclockserver

14 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 27

Brocade 5100 configuration

LOCL switch:admin> tsclockserver "132.163.135.131"

switch:admin> tsclockserver

132.163.135.131 switch:admin>

The following example shows how to set up more than one NTP server using a DNS name:

switch:admin> tsclockserver "10.32.170.1;10.32.170.2;ntp.localdomain.net" Updating Clock Server configuration...done. Updated with the NTP servers

Changes to the clock server value on the principal or primary FCS switch are propagated to all switches in the fabric

Brocade 5100 Hardware Reference Manual 15 53-1000854-02

Page 28

Brocade 5100 configuration

16 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 29

Chapter

Brocade 5100 Operation

In this chapter

•Powering the Brocade 5100 on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

•LED activity interpretation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

•POST and boot specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

•Interpreting POST results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

•Maintaining the Brocade 5100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

•Managing the Brocade 5100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Powering the Brocade 5100 on and off

To power the Brocade 5100 on, connect one or both power cords to the power connectors on the

power supplies and to a power source; then, set the AC power switches to “I”. Power is supplied to

the switch as soon as the first power supply is connected and powered on.

The switch runs POST by default each time it is powered on; it can take up to several minutes to boot and complete POST.

To power the Brocade 5100 off, power off both power supplies by setting each AC power switch to

“O”. All devices are returned to their initial state the next time the switch is powered on.

LED activity interpretation

System activity and status can be determined through the activity of the LEDs on the switch. There are three possible LED states: no light, a steady light, and a flashing light. The lights are green or amber.

Sometimes, the LEDs flash either of the colors during boot, POST, or other diagnostic tests. This is normal; it does not indicate a problem unless the LEDs do not indicate a healthy state after all boot processes and diagnostic tests are complete.

Brocade 5100 LEDs

The Brocade 5100 has the following LEDs:

• One system status LED (above) on the left side

• One power status LED (below) on the left side

• 40 port status LEDs, one for each Fibre Channel port, located above the ports

• One power supply status LED on each power supply FRU, to the left of the ON/OFF rocker

switch on the non-port side of the switch

Brocade 5100 Hardware Reference Manual 17 53-1000854-02

Page 30

LED activity interpretation

0123 891011

18 19

24 25 26 27

32 33 34 35

4 5 6 7 12 13 14 15 20

22 23

28 29 30 31

37 38 39

LED locations

Figure 4 shows the locations of the port side LEDs on the Brocade 5100.

8 9 10 11

12 13 14 15

FIGURE 4 Brocade 5100 port side LEDs

1 System status LED (top) and System power (bottom) 2 Ethernet port Status LEDs (green/amber) 3 FC port status (port 9)

Figure 5 shows the non-port side LEDs on the Brocade 5100.

1 2

FIGURE 5 Brocade 5100 non-port side LEDs

1Power supply status LED 2Power supply status LED

18 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 31

LED activity interpretation

LED Patterns

Tab le 1 describes the LEDs and their actions on the switch.

TABLE 1 Brocade 5100 LED Patterns During Normal Operation

LED Name LED Color Status of Hardware Recommended Action

Power Supply Status (right)

Power Status No light System is off or there is an internal

System Status No light System is off, boot is not complete,

Ethernet Speed

Ethernet Link No light There is no link. Verify the Ethernet cable is

No light Primary power cord is disconnected

or is not actively powered, or power supply has failed.

Steady green Power supply is operating normally. No action required.

power supply failure.

Steady green System is on and power supplies are

functioning properly.

or boot failed.

Steady green System is on and power supplies are

functioning properly.

Steady amber (for more than five seconds)

Flashing amber/green

No light Port speed is 10 Mbps. No action required.

Steady green Port speed is 100 Mbps. No action required.

Steady amber There is a link. No action required.

Flickering amber There is link activity (traffic). No action required.

Boot failed, the system is faulty. Perform the following steps:

Attention is required. A number of variables can cause this status including a single power supply failure, a fan failure, or one or more environmental ranges has exceeded.

Verify the power supply is on and seated and the power cord is connected to a functioning power source.

Verify the system is on. If the system is on, the unit is faulty.

Contact Technical Support.

No action required.

Verify the system is on and has completed booting.

No action required.

Connect a serial cable to the system. Reboot the system. Check the failure indicated on the system console. Contact Technical Support.

Check the management interface and the error log for details on the cause of status. Contact Technical Support if required.

connected correctly.

Brocade 5100 Hardware Reference Manual 19 53-1000854-02

Page 32

POST and boot specifications

TABLE 1 Brocade 5100 LED Patterns During Normal Operation (Continued)

LED Name LED Color Status of Hardware Recommended Action

Port Status No light No signal or light carrier (media or

cable) detected.

Slow flashing green (flashing in two-second intervals)

Fast flashing green (flashing in half-second intervals)

Flickering green (steady with random flashes)

Steady green Port is online (connected to external

Slow flashing amber (flashing in two-second intervals)

Fast flashing amber (flashing in half-second intervals)

Steady amber (for more than five seconds)

Port is online but segmented because of a loopback cable or incompatible switch connection.

Port is online and an internal loopback diagnostic test is running.

Port is online and frames are flowing through the port.

device) but has no traffic.

Port is disabled (because of diagnostics or the portDisable command).

Port is faulty. Check the management interface

Port is receiving light or signal carrier at 4 Gbps; but is not yet online.

Check transceiver and cable.

No action required.

Verify the diagnostic tests are not running. Reenable the port using the portEnable command.

and the error log for details on the cause of status.

Contact Technical Support if required.

No action required.

POST and boot specifications

When the switch is turned on or rebooted, the switch performs POST. Total boot time with POST can be several minutes. POST can be omitted after subsequent reboots by using the fastboot command or entering the diagDisablePost command to persistently disable POST.

For more information about these commands, refer to the Fabric OS Command Reference Manual.

POST

The success or failure results of the diagnostic tests that run during POST can be monitored through the error log or the command line interface.

POST includes the following tasks:

1. Conducts preliminary POST diagnostics.

2. Initializes the operating system.

3. Initializes hardware.

20 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 33

4. Runs diagnostic tests on several functions, including circuitry, port functionality, memory, statistics counters, and serialization.

Boot

In addition to POST, boot includes the following tasks after POST is complete:

1. Performs universal port configuration.

2. Initializes links.

3. Analyzes fabric. If any ports are connected to other switches, the switch participates in a fabric configuration.

4. Obtains a domain ID and assigning port addresses.

5. Constructs unicast routing tables.

6. Enables normal port operation.

Interpreting POST results

POST is a system check that is performed each time the switch is powered on, rebooted, or reset. During POST, the LEDs flash either amber or green. Any errors that occur during POST are listed in the error log.

Complete the following steps to determine whether POST completed successfully and whether any errors were detected:

1. Verify that the switch LEDs indicate that all components are healthy.

See Tab le 1 for descriptions and interpretations of LED patterns. If one or more LEDs do not display a healthy state, verify that the LEDs on the switch are not set to “beacon” by entering the switchShow command to detect if beaconing is active.

2. Verify that the switch prompt displays on the terminal of a computer workstation connected to the switch.

If there is no switch prompt when POST completes, press Enter. If the switch prompt still does not display, try opening a Telnet session or accessing the switch through another management tool. If this is not successful, the switch did not successfully complete POST. Contact your switch supplier for repair.

3. Review the switch system log for errors. Any errors detected during POST are written to the system log, accessible through the errShow command.

For information about all referenced commands, and on accessing the error log, refer to Fabric OS

Administrator’s Guide. For information about error messages, refer to the Fabric OS Message Reference Manual.

Maintaining the Brocade 5100

The Brocade 5100 does not require any regular physical maintenance and is designed for high availability and to minimize the chance of failure. It includes diagnostic tests and field-replaceable units, described in the following sections.

Brocade 5100 Hardware Reference Manual 21 53-1000854-02

Page 34

Maintaining the Brocade 5100

Installing an SFP

The Brocade 5100 only supports Brocade-branded SFPs. If you use an unqualified SFP, the switchShow command output shows the port in a Mod_Inv state. Fabric OS also logs the issue in the system error log.

Complete the following steps to install an SFP.

1. Making sure that the bail (wire handle) is in the unlocked position, place the SFP in the

2. Slide the SFP into the port until you feel it click into place; then close the bail.

NOTE

Each SFP has a 10-pad gold-plated PCB-edge connector on the bottom. The correct position to insert an SFP into the upper row of ports is with the gold edge down. The correct position to insert an SFP into the lower row of ports is with the gold edge up.

FIGURE 6 Installing an SFP in the upper row of port slot

correctly oriented position on the port, as shown in Figure 6.

Diagnostic tests

In addition to POST, the Fabric OS includes diagnostic tests to help you troubleshoot the hardware and firmware. This includes tests of internal connections and circuitry, fixed media, and the transceivers and cables in use.

22 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 35

Maintaining the Brocade 5100

The tests are implemented by command, either through a Telnet session or through a terminal set up for a serial connection to the switch. Some tests require the ports to be connected by external cables, to allow diagnostics to verify the serializer/deserializer interface, transceiver, and cable. Some tests require loopback plugs.

Diagnostic tests are run at link speeds of 1, 2, 4, and 8 Gbps depending on the speed of the link being tested.

NOTE

Diagnostic tests might temporarily lock the transmit and receive speed of the links during diagnostic testing.

For information about specific diagnostic tests, refer to the Fabric OS Troubleshooting and

Diagnostics Guide.

Field Replaceable Units (FRUs)

The power supplies have the fans inside and can be replaced onsite without the use of special tools. The power supply/fan assembly units are keyed to ensure correct orientation during installation. Replacement instructions are provided with all replacement units ordered.

Power supply/fan assembly FRU replacement

The Brocade 5100 fans are fixed inside the integrated power supply/fan FRU to provide necessary airflow to cool the whole system. There is one fan located in the rear section of each FRU. The system software sets fan speed and measures their speeds through the tachometer interface.

The two power supply/fan assembly FRU units are hot-swappable if replaced one at a time. They are identical and fit into either slot.

Fabric OS identifies the power supplies as follows (viewing the switch from the port side):

• Power supply #1 is on the left

• Power supply #2 is on the right

Determining power supply/fan replacement need

1. Use one of the following methods to determine whether a power supply requires replacement:

• Check the power supply status LED next to the I/O switch. If the power supply status LED

is not on, verify that the power supply is on and seated and the power cord is connected to a functioning power source. If the light does not turn green, the power supply needs to be replaced.

• In Web Tools, click the Power Status icon.

• Typ e t h e psShow command at the command prompt to display power supply status as

shown below:

switch:admin> psshow

Power Supply #1 is OK Power Supply #2 is OK

Brocade 5100 Hardware Reference Manual 23 53-1000854-02

Page 36

Managing the Brocade 5100

2. Use one of the following methods to determine whether a fan requires replacement:

For further information on replacing the power/fan units, see the Brocade 5100 Power Supply and Fan Assembly Replacement Procedure.

• Check the system status LED (see Figure 4 on page 18 for location of system status LED).

If the system status LED is flashing amber and green, it could mean the fan has failed. The green power supply/fan LED will also flash in the event of failure. Check the management interface and the error log for details on the cause of status.

• In Advanced Web Tools, check the Fan Status icon background color. It will be either yellow

or red if the fan has failed. When the fan is functioning correctly, the background color is green.

• Typ e t h e fanShow command at the command prompt to display fan status as shown

below:

switch:admin> fanshow Fan 1 is OK, speed is 7105 RPM Fan 2 is OK, speed is 7258 RPM

Managing the Brocade 5100

You can use the management functions built into the Brocade 5100 to monitor the fabric topology, port status, physical status, and other information to help you analyze switch performance and to accelerate system debugging.

The Brocade 5100 automatically performs power-on-self-test (POST) each time it is turned on. Any errors are recorded in the error log. For more information about POST, see “POST and boot

specifications” on page 20.

For information about upgrading the version of Fabric OS installed on your switch, refer to the

Fabric OS Administrator’s Guide.

You can manage the Brocade 5100 using any of the management options listed in Table 2.

TABLE 2 Management Options for the Brocade 5100 Switch

Management Tool Out-of-band Support In-band Support

Command line interface (CLI) Up to two admin sessions and four user sessions simultaneously.

For more information, refer to the Fabric OS Administrator’s Guide and the Fabric OS Command Reference Manual.

Brocade Web Tools For information, refer to the Web Tools Administrator’s Guide.

Standard SNMP applications For information, refer to the MIB Reference Manual.

Brocade Fabric Manager (option to purchase) For information, refer to the Fabric Manager Administrator’s Guide.

Management Server For information, refer to the Fabric OS Administrator’s Guide and

the Fabric OS Command Reference Manual.

EFCM (option to purchase) For information, refer to the EFCM documentation set.

Ethernet or serial connection

IP over Fibre Channel

Native in-band interface (over HBA only)

IP over Fibre Channel

24 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 37

Managing the Brocade 5100

NOTE

To achieve in-band support for IP over Fibre Channel, the sof tware must be run on both the HBA and the switch, and it must be supported by both the HBA and HBA driver.

Brocade 5100 Hardware Reference Manual 25 53-1000854-02

Page 38

Managing the Brocade 5100

26 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 39

Appendix

Brocade 5100 Specifications

In this appendix

•Switch components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

•Weight and physical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•Facility requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•Power supply specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

•Environmental requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

•General specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

•Data transmission ranges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

•Memory specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

•Fibre Channel port specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

•Serial port specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

•Regulatory compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

•Environmental regulation compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Switch components

The Brocade 5100 switch includes the following components:

• Cabinet-mountable 1U chassis, designed for a 19-inch cabinet space, with forced-air cooling

that flows from the non-port side of the switch to the port side.

• 40 Fibre Channel ports, compatible with short wavelength (SWL), long wavelength (LWL), and

extended long wavelength (ELWL) SFP transceivers

• One RJ-45 serial port on the port side of the switch

• One IEEE-compliant RJ-45 connector on the port side of the switch for use with 10/100 Mbps

Ethernet

• 40 port LEDs, 1 switch power LED, 1 switch status LED, 2 Ethernet LEDs, and 2 power supply

LEDs

• One USB port for system log file downloads or firmware upgrades

• Two universal AC input and redundant power supplies with AC switches and built-in fans

Brocade 5100 Hardware Reference Manual 27 53-1000854-02

Page 40

Weight and physical dimensions

Tab le 3 lists the weight and dimensions of the Brocade 5100.

TABLE 3 Physical Specifications

Dimension Value

Height 1U = 43 mm (1.7 inches)

Depth 610.535 mm (24 inches)

Width 428.75 mm (16.88 inches)

Weight (with two power supply/fan assembly units installed, no SFPs) 9.3 kg (20.6 lbs)

Facility requirements

Tab le 4 provides the facilities requirements that must be met for the Brocade 5100.

TABLE 4 Facility Requirements

Type Requirements

Electrical • Primary AC input 100-240 VAC, 2.0A, 47-63 Hz; switch autosenses input voltage

• Adequate supply circuit, line fusing, and wire size, as specified by the electrical rating

• Circuit protected by a circuit breaker and grounded in accordance with local electrical

Refer to Table 5 on page 28 for complete power supply specifications.

Thermal

• A minimum air flow of 79.8 cubic meters/hour (47 cubic ft/min.) available in the

• Ambient air temperature not exceeding 40° C (104° F) while the switch is operating

Cabinet (when rack-mounted)

• One rack unit (1U) in a 48.3 cm (19-inch) cabinet

• All equipment in cabinet grounded through a reliable branch circuit connection

• Additional weight of switch not to exceed the cabinet’s weight limits

• Cabinet secured to ensure stability in case of unexpected movement

Power supply specifications

The power supplies are universal and capable of functioning worldwide without voltage jumpers or switches. They meet IEC 61000-4-5 surge voltage requirements and are autoranging in terms of accommodating input voltages and line frequencies. Each power supply has a built-in fan for cooling, pushing air towards the port side of the switch.

Tab le 5 lists the power supply specifications for the Brocade 5100.

TABLE 5 Power Supply Specifications

Specification Value

on the switch nameplate

codes

immediate vicinity of the switch

Inlet C13

Maximum output of one power supply

28 Brocade 5100 Hardware Reference Manual

125 Watts

53-1000854-02

Page 41

TABLE 5 Power Supply Specifications

Specification Value

System power consumption 84 Watts nominal, 91 Watts Maximum

Input voltage 85 - 264 VAC, Universal

Input line frequency 47 - 63 Hz

BTU rating 406 BTU/hr

Inrush current 35 Amps Maximum

Environmental requirements

Tab le 6 lists the acceptable environmental ranges for both operating and nonoperating (such as

during transportation or storage) conditions.

TABLE 6 Environmental Requirements

Condition Acceptable During Operation Acceptable During Non-Operation

Environmental requirements

Ambient Tem pera ture

Humidity 10% to 85% RH non-condensing, at

Altitude 3,000 meters (9,842 feet) above sea level 0 to 12 kilometers (39,370 feet) above sea

Shock 20 G, 6 ms, half-sine wave Half sine, 33G 11ms, 3/e.g. Axis

Vibration 0.5 G sine, 0.4 grms random, 5-500 Hz 2.0 G sine, 1.1 grms random 5-500 Hz

Air flow High speed, 13,000 RPM,

General specifications

Tab le 7 lists the general specifications for the Brocade 5100.

TABLE 7 General Specifications

Specification Description

Configurable port types E_Port, F_Port, FL_Port, M_Port, and EX_Port

System architecture Nonblocking shared-memory switch

System processor Power PC 440EPX,667 MHz CPU

ANSI Fibre Channel protocol FC-PH (Fibre Channel Physical and Signalling Interface standard)

Modes of operation Fibre Channel Class 2 and Class 3

Fabric initialization Complies with FC-SW-3 Rev. 6.6

FC-IP (IP over Fibre Channel) Complies with FC-IP 2.3 of FCA profile

0° to 40° Celsius (32

° to 104° Fahrenheit)

40° Celsius (104 gradient of 10% per hour

Low speed, 7000 RPM,

° Fahrenheit), with maximum

49.3 CMH (29 CFM)

37.4 CMH (22 CFM)

° to 70° Celsius

-25 (-13

° to 158° Fahrenheit)

10% to 90% RH non-condensing, at 70° Celsius (158

level

None required

° Fahrenheit)

Brocade 5100 Hardware Reference Manual 29 53-1000854-02

Page 42

Data transmission ranges

TABLE 7 General Specifications

Specification Description

Aggregate switch I/O bandwidth 640 Gbps if all 40 ports are running at 8 Gbps, full duplex

Port-to-port latency 700 nanoseconds

Tab le 8 lists the EMC (electromagnetic compatibility) for the Brocade 5100.

TABLE 8 EMC specifications

Country Safety EMC

United States Bi_Nat UL/CSA 60950-1 1st Ed or

Canada Bi_Nat UL/CSA 60950-1 1st Ed or

Japan CISPR22 and JEIDA (Harmonics)

European Community EN60950-1 or latest EN55022 and EN55024

Australia/New Zealand EN55022 or CISPR22 or AS/NZS

Argentina IEC60950-1 or latest

Russian Federation IEC60950-1 or latest 51318.22-99 and 51318.24.99

Korea KN22 and KN24

China (PS only) GB4943-2001 and

Taiwan (PS only) CNS 14336(94) or latest CNS 13438(95) or latest

Data transmission ranges

Tab le 9 provides the data transmission ranges for different cable types and port speeds.

TABLE 9 Laser Data Transmission Ranges

Port Speed Cable Size

(microns)

ANSI C63.4

latest

ICES-003 Class A

latest

CISPR22

GB17625.1-2003 or latest

GB9254-1998 or latest

Short Wavelength (SWL) Long Wavelength (LWL) Extended Long

Wavelength (ELWL)

1 Gbps 50 500 m (1,640 ft) (OM2)

30 Brocade 5100 Hardware Reference Manual

NA NA

860 m (2,821 ft) (OM3)

62.5 300 meters (984 feet) NA NA

9 NA 10 km (6.2 miles) 40 km (24.8 miles)

53-1000854-02

Page 43

TABLE 9 Laser Data Transmission Ranges

Port Speed Cable Size

(microns)

Short Wavelength (SWL) Long Wavelength (LWL) Extended Long

Memory specifications

Wavelength (ELWL)

2 Gbps 50 300 m (984 ft) (OM2)

4 Gbps 50 150 m (492 ft) (OM2)

8 Gbps 50 50 m (164 ft) (OM2)

Memory specifications

The Brocade 5100 has three types of memory devices.

NA NA

500 m (1,640 ft) (OM3)

62.5 150 m (492 feet) NA NA

9 NA 10 km (6.2 miles)

without a Brocade Extended Fabrics license; 50 to 100 km with a Brocade Extended Fabrics license

NA NA

380 m (1,246 ft) (OM3)

62.5 70 m (230 feet) NA NA

9NA NA NA

NA NA

150 m (492 ft) (OM3)

62.5 21 m (69 feet) NA NA

9NA 10 km NA

40 km (24.8 miles)

TABLE 10 Brocade 5100 memory specifications

Type Size

Boot flash 4 MB

Compact flash 1 GB

Main memory (SDRAM) 512 MB

Fibre Channel port specifications

The Fibre Channel ports in the Brocade 5100 are compatible with SWL, LWL, and ELWL SFP transceivers. The strength of the signal is determined by the type of transceiver in use.

The ports meet all required safety standards. For more information about these standards, see

“Regulatory compliance” on page 32.

The ports are capable of operating at 1, 2, 4, or 8 Gbps and are able to autonegotiate to the higher speed.

Brocade 5100 Hardware Reference Manual 31 53-1000854-02

Page 44

Serial port specifications

The serial port is located on the port side of the switch. The Brocade 5100 uses an RJ-45 connector for the serial port.

NOTE

To protect the serial port from damage, keep the cover on the port when not in use.

The serial port can be used to connect to a workstation to configure the switch IP address before connecting the switch to a fabric or IP network. The serial port’s parameters are fixed at 9600 baud, 8 data bits, and no parity, with flow control set to None.

This connector is for initial IP address configuration and for recovery of the switch to its factory default settings if Flash memory contents are lost. The serial port is not intended for performance of normal administration or maintenance functions. You should only use this port to connect a terminal to the port to re-initialize the switch defaults, restoring the switch to its factory configuration. This is required to restore switch passwords to a known state and allow you to assign an IP address to the switch.

Tab le 11 lists the serial cable pinouts.

TABLE 11 Serial Cable Pinouts

PIN Signal Description

1Not supported NA

2Not supported NA

3UART1_TXD Transmit data

4 GND Logic ground

5 GND Logic ground

6UART1_RXD Receive data

7Not supported NA

8Not supported NA

Regulatory compliance

This section describes the regulatory compliance requirements for the Brocade 5100 switch. It contains:

• “FCC warning (US only),” next

• “MIC statement (Republic of Korea)” on page 33

• “VCCI statement Japan” on page 33

• “BSMI statement (Taiwan)” on page 34

• “CE statement” on page 34

• “Canadian requirements” on page 34

• “Laser compliance” on page 35

• “RTC battery” on page 35

• “Electrical safety” on page 35

32 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 45

Regulatory compliance

• “Regulatory certifications” on page 35

FCC warning (US only)

This equipment has been tested and complies with the limits for a Class A computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, might cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

MIC statement (Republic of Korea)

VCCI statement Japan

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance might arise. When such trouble occurs, the user might be required to take corrective actions.

Power cords (Japan Denan)

Brocade 5100 Hardware Reference Manual 33 53-1000854-02

Page 46

Regulatory compliance

BSMI statement (Taiwan)

The BSMI Statement is applicable to Brocade 5100 power supplies.

CE statement

ATTENTION

This is a Class A product. In a domestic environment, this product might cause radio interference, and the user might be required to take corrective measures.

The standards compliance label on the Brocade 5100 contains the CE mark which indicates that this system conforms to the provisions of the following European Council directives, laws, and standards:

• Electromagnetic Compatibility (EMC) Directive 2004/108/EEC

• Low Voltage Directive (LVD) 2006/95/EC

• EN50082-2/EN55024:1998 (European Immunity Requirements)

• EN61000-3-2/JEIDA (European and Japanese Harmonics Spec)

• EN61000-3-3

Canadian requirements

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations, ICES-003 Class A.

34 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 47

Regulatory compliance

Laser compliance

This equipment contains Class 1 laser products and complies with FDA Radiation Performance Standards, 21 CFR Subchapter I and the international laser safety standard IEC 825-2.

ATTENTION

Use only optical transceivers that are qualified by Brocade Communications Systems, Inc. and comply with the FDA Class 1 radiation performance requirements defined in 21 CFR Subchapter I, and with IEC 825-2. Optical products that do not comply with these standards might emit light that is hazardous to the eyes.

RTC battery

ATTENTION

Do not attempt to replace the real-time clock (RTC) battery. There is danger of explosion if the battery is incorrectly replaced or disposed of. Contact your switch supplier if the real-time clock begins to lose time.

Electrical safety

ATTENTION

This switch might have more than one power cord. To reduce the risk of electric shock, disconnect both power cords before servicing.

ATTENTION

Connect the power cord only to a grounded outlet.

ATTENTION

This product is designed for an IT power system with phase-to-phase voltage of 230V. After operation of the protective device, the equipment is still under voltage if it is connected to an IT power system.

Regulatory certifications

Tab le 12 lists the EMC compatibility for the Brocade 5100.

TABLE 12 EMC (electromagnetic compatibility)

Country Safety EMC

United States Bi_Nat UL/CSA 60950-1 1st Ed or

latest

Canada Bi_Nat UL/CSA 60950-1 1st Ed or

latest

ANSI C63.4

ICES-003 Class A

Japan CISPR22 and JEIDA (Harmonics)

European Community EN60950-1 or latest EN55022 and EN55024

Brocade 5100 Hardware Reference Manual 35 53-1000854-02

Page 48

Environmental regulation compliance

TABLE 12 EMC (electromagnetic compatibility)

Country Safety EMC

Australia/New Zealand EN55022 or CISPR22 or AS/NZS

Argentina IEC60950-1 or latest

Russian Federation IEC60950-1 or latest 51318.22-99 and 51318.24.99

Korea KN22 and KN24

China (PS only) GB4943-2001 and

GB9254-1998 or latest

Taiwan (PS only) CNS 14336(94) or latest CNS 13438(95) or latest

Environmental regulation compliance

This section describes the “China RoHS” environmental regulatory compliance requirements for the Brocade 5100 switch.

CISPR22

GB17625.1-2003 or latest

China RoHS

The contents included in this section are per the requirements of the People's Republic of ChinaManagement Methods for Controlling Pollution by Electronic Information products.

䙉ᅜ⦃๗⊩㾘 Ё೑ RoHS ᴀ㡖Ёࣙ৿ⱘݙᆍ䛑䙉ᅜњЁҎ⇥݅೑ǉ⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩Ǌⱘ 㽕∖Ǆ

Environmental protection use period (EPUP) disclaimer

In no event do the EPUP logos shown on the product and FRUs alter or expand that warranty that Brocade provides with respect to its products as set forth in the applicable contract between Brocade and its customer. Brocade hereby disclaims all other warranties and representations with respect to the information contained on this CD including the implied warranties of merchantability, fitness for a particular purposes and non-infringement.

The EPUP assumes that the product will be used under normal conditions in accordance with the operating manual of the product.

⦃ֱՓ⫼ᳳ䰤 (EPUP) ܡ䋷ໄᯢ˖

EPUP 󰵼ᖫϡӮߎ⦄೼ѻક FRU ⱘᬍ㺙ѻકЁˈгϡӮᇍ Brocade

᠔ᦤկⱘⳌ݇ѻકֱׂᴵℒ˄䆹ֱׂᴵℒ೼ Brocade ঞ݊ᅶ᠋䯈䖒៤ⱘ䗖⫼ড়ৠЁ߫ߎ˅䖯㸠๲㸹ǄᇍѢℸ CD Ϟࣙ৿ⱘⳌֵ݇ᙃˈབ䗖䫔ᗻǃ䩜ᇍ⡍ᅮ⫼䗨ⱘ䗖⫼ᗻ䴲։ᴗᗻⱘᱫ⼎ֱ䆕ˈBr

ocade ೼ℸ䚥䞡ໄᯢᴀ݀ৌᇍѢϢϞ䗄ֵᙃⳌ݇ⱘ᠔᳝݊Ҫֱ䆕䰜䗄ὖϡ䋳䋷Ǆ EPUP ؛䆒೼Āѻક᪡԰᠟ݠāЁ⊼ᯢⱘᐌ㾘ᴵӊϟՓ⫼䆹ѻકǄ

36 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 49

Environmental regulation compliance

TS/HS dual language sheet

In accordance with China's Management Measures on the Control of Pollution caused by Electronic Information products (Decree No. 39 by the Ministry of Information Industry), the following information is provided regarding the names and concentration level of Hazardous substances (HS) which may be contained in this product.

TABLE 13 China ROHS hazardous substances/toxic substances (HS/TS) concentration chart

Name of the Component

Hazardous/Toxic Substance/Elements

Lead (PB) Mercury

(Hg)

Cadmium (CD)

Hexavalent Chromium (CR6+)

Polybrominated Biphenyl (PBB)

Polybrominated Diphenyl Ether (PBDE)

Fibre Channel Switch

Fan, Blower assemblies

PCBA cards X O O O O O

Power Supply kit X O O O O O

SFPs (optical

XOOO O O

XOOO O O cable connectors)

Sheet Metal X O O O O O

Chassis Assembly

Mechanical brackets and Slides

Slot Filler X O O O O O

Cable management tray

Cable Comb O O O O O O

Cables and power cords

Replacement Doors

Software/ Documentation CDs

XOOO O O

OO OO O O

XOOO O O

OO OO O O

X indicates that the concentration of such hazardous/toxic substance in all the units of homogeneous material of such component is higher than the SJ/T11363-2006 Requirements for Concentration Limits.

O indicates that no such substances are used or that the concentration is within the aforementioned limits.

Brocade 5100 Hardware Reference Manual 37 53-1000854-02

Page 50

Environmental regulation compliance

38 Brocade 5100 Hardware Reference Manual

53-1000854-02

Page 51

Index

access

NTP

, 14

accessory kit

, 7

bandwidth, aggregate, 30 Brocade Advanced Web Tools Brocade Fabric Manager Brocade ISL Trunking BSMI statement (Chinese)

, 24

, 4, 5

, 34

Canadian requirements, 34 CE statement China RoHS class

Fibre Channel classes supported

Command line interface (CLI) components, switch configuring

date and time NTP

configuring the Brocade 5100

, 34

, 36

, 27

, 12

, 14

, 24

, 10

, 29

EIA rack

requirements electrical safety environmental requirements

event

date and time

, 28

, 35

, 29

, 12

Fabric Manager, 24 FCC warning (US only) Fibre Channel classes, supported Fibre Channel ports

specifications Field replaceable units (FRUs)

front panel

LEDs

, 17

, 33

, 29

, 31

, 4

installing a Brocade 5100 into an EIA cabinet, 10 installing a stand-alone Brocade 5100 installing an SFP interpreting POST results IP over Fibre Channel (FC-IP) ISL trunking groups items required for installation

, 22

, 21

, 29

, 5

, 9

date, 13 date and time diagnostic tests

about

, 12

, 22

EFCM, 24

Brocade 5100 Hardware Reference Manual 39 53-1000854-02

laser compliance, 35 latency

, 30

LEDs

interpreting

on front panel local clock

, 14

LOCL logging

timestamp

, 17

, 14

, 12

Page 52

Management Server, 24 MIC statement (Republic of Korea) monitoring

through LED activity

, 17

NTP

access

, 14

, 33

requirements

airflow

, 28

electrical

environmental

facility

rack

shock and vibration

temperature and humidity RJ-45 connector RS-232 connector

RTC battery

, 28

, 28, 29

, 28

, 27

, 35

, 29

physical dimensions of switch, 28 port

configurable types Ethernet port Fibre Channel port serial port trunking

port numbering port status LEDs Ports On Demand ports, enabling ports, numbering POST

error messages interpreting

POST and boot specifications power status LED power supply

general information specifications

power supply status LED protocol, ANSI provide power to the switch

, 27, 32

, 4, 5

, 29

, 27

, 31

, 3

, 17

, 5

, 3

, 21

, 20

, 17

, 27

, 28

, 17

, 10

serial port

specifications setting

time zone setting the date and time setting the IP address

setting the switch date and time Setting time zones settings

date and time SNMP

, 24

specifications

Fibre Channel ports

general

power supply

serial port switch

components

physical dimensions

weight

, 28

system status LED

, 32

, 14

, 12

, 11

, 14

, 12

, 31

, 29

, 28

, 32

, 27

, 28

, 17

, 12

rack

requirements recommendations for cable management regulatory certifications

regulatory compliance

40 Brocade 5100 Hardware Reference Manual

, 28

, 35

, 32

, 8

temperature requirements, 29 tests, diagnostic time

, 12

time and date Time zones time zones trunking

about

tsclockserver tsTimeZone

, 22

, 12

, 4, 5

, 14

53-1000854-02

Page 53

VCCI statement, 33

weight, switch, 28

Brocade 5100 Hardware Reference Manual 41 53-1000854-02

Page 54

42 Brocade 5100 Hardware Reference Manual

53-1000854-02