Brocade Communications Systems 1606, AM866A - StorageWorks 8/8 Base SAN Switch, 8/24, 8/40, 8/8 Reference

...

53-1001339-01 28 July 2009

Fabric OS

MIB Reference

Supporting Fabric OS v3.1.x, v3.2.x, v4.1.x, v4.2.x, v4.4.x, v5.0.x, v5.1.x, v5.2.x, v5.3.x, v6.0.0, v6.1.0, v6.2.0, v6.1.2_CEE, v6.3.0

Brocade, the B-wing symbol, BigIron, DCX, Fabric OS, FastIron, IronPoint, IronShield, IronView, IronWare, JetCore, NetIron, SecureIron, ServerIron, StorageX, and TurboIron are registered trademarks, and DCFM, Extraordinary Networks, and SAN Health are trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time, without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available. Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with respect to any loss, cost, liability, or damages arising from the information contained in this book or the computer programs that accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other open source license agreements. To find-out which open source software is included in Brocade products, view the licensing terms applicable to the open source software, and obtain a copy of the programming source code, please visit http://www.brocade.com/support/oscd.

Brocade Communications Systems, Incorporated

Corporate and Latin American Headquarters Brocade Communications Systems, Inc. 1745 Technology Drive San Jose, CA 95110 Tel: 1-408-333-8000 Fax: 1-408-333-8101 E-mail: info@brocade.com

European Headquarters Brocade Communications Switzerland Sàrl Centre Swissair Tour B - 4ème étage 29, Route de l'Aéroport Case Postale 105 CH-1215 Genève 15 Switzerland Tel: +41 22 799 5640 Fax: +41 22 799 5641 E-mail: emea-info@brocade.com

Asia-Pacific Headquarters Brocade Communications Systems China HK, Ltd. No. 1 Guanghua Road Chao Yang District Units 2718 and 2818 Beijing 100020, China Tel: +8610 6588 8888 Fax: +8610 6588 9999 E-mail: china-info@brocade.com

Asia-Pacific Headquarters Brocade Communications Systems Co., Ltd. (Shenzhen WFOE) Citic Plaza No. 233 Tian He Road North Unit 1308 – 13th Floor Guangzhou, China Tel: +8620 3891 2000 Fax: +8620 3891 2111 E-mail: china-info@brocade.com

Document History

Document Title Publication Number Summary of Changes Publication Date

Brocade MIB Reference Manual v2.3 53-0000069-02 December 2000

Brocade MIB Reference Manual v3.0 53-0000134-03 July 2001

Brocade MIB Reference Manual v3.0, 4.0 53-0000184-02 March 2002

Brocade MIB Reference Manual (v4.1, v4.0.x, v3.1, v3.0.x, v2.6.x)

Brocade MIB Reference Manual (v4.1.2, v4.1, v4.0.x, v3.1, v3.0.x, v2.6.x)

Brocade MIB Reference Manual (v4.2.0, v4.1.2, v4.1, v4.0.x, v3.1, v3.0.x, v2.6.x)

53-0000521-02 Added Brocade-specific

Entity and HA-MIBs.

53-0000521-03 Added FICON information. May 2003

53-0000521-04 Revised FICON

information.

53-0000521-06 Update to support the

Brocade 3250, 3850, and 24000 switches.

April 2003

October 2003

December 2003

Document Title Publication Number Summary of Changes Publication Date

Brocade Fabric OS MIB Reference Manual 53-0000521-08 Updated to support the

Brocade 4100.

Brocade Fabric OS MIB Reference Manual 53-0000521-09 Updated to support the

Brocade 48000 and 200E.

Brocade Fabric OS MIB Reference Manual 53-1000045-01 Updated to support the

Brocade 4900, 7500, and FR4-18i blade.

Brocade Fabric OS MIB Reference 53-1000241-01 Changed name, updated

to support Fabric OS 5.2.x

Brocade Fabric OS MIB Reference 53-1000439-01 New branding, updated to

support Fabric OS 5.3.0

Brocade Fabric OS MIB Reference 53-1000602-01 Updated to support the

Brocade DCX Data Center Backbone Director

Brocade Fabric OS MIB Reference 53-1000602-02 Updated to support the

Brocade 300, 5100, and 5300 switches.

Brocade Fabric OS MIB Reference 53-1001156-01 Updated to support the

Brocade DCX-4S and Brocade Encryption Switch.

Fabric OS MIB Reference 53-1001339-01 Updated to support the

Brocade 7800 Extension Switch, Brocade 8000 Switch, FCOE10-24 DCX Blade, and FX8-24 DCX Extension Blade. Added USM MIB details, fcipTcpConnTable and fcipConnStatsTable.

September 2004

April 2005

January 2006

September 2006

June 2007

October 2007

March 2008

November 2008

July 2009

Contents

About This Document

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Supported hardware and software . . . . . . . . . . . . . . . . . . . . . . . . . . xii

What’s new in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Document conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Notice to the reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

Getting technical help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi

Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvii

Chapter 1 Understanding Brocade SNMP

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Setting the SNMP security level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Understanding SNMP basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Understanding MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Understanding SNMP traps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Object instances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Loading Brocade MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Brocade MIB files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before loading MIBs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

MIB loading order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

SNMP CLI usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Brocade 7500 / FR4-18i and Brocade MIBs . . . . . . . . . . . . . . . . . .13

Access Gateway and Brocade MIBs. . . . . . . . . . . . . . . . . . . . . . . . . .13

Firmware upgrades and enabled traps . . . . . . . . . . . . . . . . . . . . . . .13

Fabric OS commands for configuring SNMP . . . . . . . . . . . . . . . . . . .14

Support for Administrative Domains . . . . . . . . . . . . . . . . . . . . . . . . . 14

Support for Role Based Access Control. . . . . . . . . . . . . . . . . . . . . . .15

Support for IP V6 addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Support for Virtual Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Chapter 2 MIB-II (RFC1213-MIB)

Fabric OS MIB Reference v 53-1001339-01

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

MIB II overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

System group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Interfaces group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

AT group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

IP group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

ICMP group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

TCP group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

UDP group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

EGP group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Transmission group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

SNMP group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

RMON group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

ifMIB group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Chapter 3 FE MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

FE MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

FIBRE-CHANNEL-FE-MIB (MIB-II branch) . . . . . . . . . . . . . . . . . . . . . .63

Definitions for FIBRE-CHANNEL-FE-MIB. . . . . . . . . . . . . . . . . . . . . . .67

fcFeConfig group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

fcFeStatus group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

fcFeError group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

feFcAccounting group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

fcFeCapability group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

FCFABRIC-ELEMENT-MIB (experimental branch) . . . . . . . . . . . . . . .86

fcFeConfig group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

fcFeOp group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

fcFeError group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101

fcFeAcct group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

fcFeCap group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Chapter 4 Entity MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

Entity MIB overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107

Entity MIB system organization of MIB objects . . . . . . . . . . . .107

Definitions for Entity MIB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109

Textual conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110

vi Fabric OS MIB Reference

Entity MIB objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

53-1001339-01

Physical Entity group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112

Logical Entity group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120

Entity Mapping group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

General group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125

Entity MIB trap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125

Entity MIB Conformance information. . . . . . . . . . . . . . . . . . . . . . . .126

Chapter 5 SW-MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129

SW MIB overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129

SW-MIB system organization of MIB objects . . . . . . . . . . . . . .129

Textual conventions for SW-MIB . . . . . . . . . . . . . . . . . . . . . . . .135

sw traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138

swSystem group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144

Flash administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147

swFabric group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153

SW Agent Configuration group . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157

Fibre Channel Port group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158

Name Server Database group . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165

Event group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167

Fabric Watch group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169

End Device group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178

Switch group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180

ASIC Performance Monitoring group . . . . . . . . . . . . . . . . . . . . . . . .181

Trunking group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183

Toptalker group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185

CPU or memory usage group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186

Chapter 6 High-Availability MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189

HA MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189

High-Availability group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191

FRU Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191

FRU History Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .193

CP Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195

HA-MIB traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196

HA-MIB traps and sample triggers . . . . . . . . . . . . . . . . . . . . . .197

Fabric OS MIB Reference vii 53-1001339-01

Chapter 7 FICON MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199

FICON MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199

SNMP traps for FICON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199

FICON MIB system organization of MIB objects. . . . . . . . . . . .199

Textual conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201

ficonRNID group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202

ficonLIRR group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206

ficonRLIR group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207

linkIncidentMIBTraps group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208

Chapter 8 FibreAlliance MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211

FibreAlliance MIB overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211

FCMGMT-MIB system organization of MIB objects . . . . . . . . .211

Definitions for FCMGMT-MIB. . . . . . . . . . . . . . . . . . . . . . . . . . .215

ConnSet group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216

Statistics group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .243

Service group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .252

SNMP Trap Registration group . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254

Revision Number Scalar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255

Unsupported tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256

FibreAlliance MIB traps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256

Chapter 9 FCIP MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259

FCIP MIB overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259

FCIP MIB system organization of MIB objects . . . . . . . . . . . . .259

fcipEntityInstanceTable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261

fcipLinkTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262

fcipTcpConnTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .264

fcipExtendedLinkTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265

fcipConnStatsTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266

Chapter 10 iSCSI MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269

iSCSI MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269

iSCSI MIB system organization of MIB objects . . . . . . . . . . . .269

iscsiInstanceAttributesTable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271

iscsiNodeAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

viii Fabric OS MIB Reference

53-1001339-01

iscsiSessionAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277

iscsiSessionStatsTable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280

iscsiConnectionAttributesTable . . . . . . . . . . . . . . . . . . . . . . . . . . . .282

Chapter 11 USM MIB Objects

In this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285

USM MIB objects overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285

usmMIBObjects group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286

usmStats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .286

usmUser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287

Appendix A MIB Object Groupings

Switch variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291

Sensor variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291

Port variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291

Event variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .292

ISL and End Device variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .292

SNMP Configuration variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .292

iSCSI Instance Information variables. . . . . . . . . . . . . . . . . . . . . . . .293

Appendix B MIB OIDs and their Matching Object Names

MIB OIDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .295

Index

Fabric OS MIB Reference ix 53-1001339-01

x Fabric OS MIB Reference

53-1001339-01

About This Document

In this chapter

•How this document is organized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

•Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

•What’s new in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

•Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

•Additional information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv

•Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi

•Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii

How this document is organized

This document is organized to help you find the information that you want as quickly and easily as possible.

The document contains the following components:

• Chapter 1, “Understanding Brocade SNMP,” provides an introduction to Brocade SNMP and

MIBs.

• Chapter 2, “MIB-II (RFC1213-MIB),” provides information for MIB-II.

• Chapter 3, “FE MIB Objects,” provides information for FE MIB object types.

• Chapter 4, “Entity MIB Objects,” provides information for Entity MIB object types.

• Chapter 5, “SW-MIB Objects,” provides information for FC Switch MIB (SW-MIB) object types.

• Chapter 6, “High-Availability MIB Objects,” provides information for High-Availability MIB object

types.

• Chapter 7, “FICON MIB Objects,” provides information for FICON MIB (LINK-INCIDENT-MIB)

object types.

• Chapter 8, “FibreAlliance MIB Objects,” provides information for FibreAlliance MIB

(FCMGMT-MIB) object types.

• Chapter 9, “FCIP MIB Objects,” provides information on FCIP MIB support for 7500 switches

and FC4-18i blades.

• Chapter 10, “iSCSI MIB Objects,” provides information on iSCSI MIB support for 7500 switches

and FC4-18i blades.

• Chapter 11, “USM MIB Objects,” provides information on USM MIB.

• Appendix A, “MIB Object Groupings,” is a function-based listing of MIB objects.

Fabric OS MIB Reference xi 53-1001339-01

• Appendix B, “MIB OIDs and their Matching Object Names,” provides a listing of the MIB object

names and the corresponding MIB Object ID (OID) associated with each.

Supported hardware and software

In those instances in which procedures or parts of procedures documented here apply to some switches but not to others, this guide identifies exactly which switches are supported and which are not.

Although many different software and hardware configurations are tested and supported by Brocade Communications Systems, Inc. for 6.3.0, documenting all possible configurations and scenarios is beyond the scope of this document.

This document supports Brocade Fabric OS versions v6.3.0 and earlier versions,v6.2.0, v6.1.2_CEE, v6.1.0, v6.0.0, v5.3.x, v 5.2.x, v5.1.x, v5.0.x, v4.4.0, v4.2.x, v4.1.x, v3.2.x, v3.1.x and all switches supporting these Fabric OS versions, including:

• Brocade 300

• Brocade 4100

• Brocade 4900

• Brocade 5000

• Brocade 5100

• Brocade 5300

• Brocade 5410

• Brocade 5480

• Brocade 5424

• Brocade 5450

• Brocade 7500

• Brocade 7500E

• Brocade 7600

• Brocade 7800 Extension Switch

• Brocade 8000 FCoE Switch

• Brocade Encryption Switch

• Brocade DCX Backbone and Brocade DCX-4S Backbone

- FA4-18 Fibre Channel application blade

- FCOE10-24 DCX Blade

- FS8-18 Encryption Blade

- FC8-16 port blade

- FC8-32 port blade

- FC8-48 port blade

- FC10-6 port blade

- FR4-18i router blade

- FX8-24 DCX Extension Blade (new)

xii Fabric OS MIB Reference

53-1001339-01

• Brocade 48000 director

- FA4-18 Fibre Channel application blade

- FC4-16 port blade

- FC4-16IP

- FC4-32 port blade

- FC4-48 port blade

- FC10-6 port blade

- FR4-18i router blade

What’s new in this document

The following changes have been made since this document was last released:

• Information that was added:

- Support for Brocade 7800 Extension Switch, Brocade 8000, FCOE10-24 DCX Blade, and

FX8-24 DCX Extension Blade

- The following MIB objects included:

• RMON MIB

• USM MIB

• fcipTcpConnTable

• fcipConnStatsTable

• snmpSilentDrops

• snmpProxyDrops

• Information that was changed:

- sysContact

- sysLocation

- The following entries are updated as obsolete:

• swGroupName

• swGroupType

• swGroupMemPos

- Change of version number wherever applicable

- Miscellaneous additions and corrections have been made throughout

For further information about new features and documentation updates for this release, refer to the release notes.

Document conventions

This section describes text formatting conventions and important notices formats.

Fabric OS MIB Reference xiii 53-1001339-01

Text formatting

The narrative-text formatting conventions that are used in this document are as follows:

bold text Identifies command names

Identifies the names of user-manipulated GUI elements Identifies keywords and operands Identifies text to enter at the GUI or CLI

italic text Provides emphasis

Identifies variables Identifies paths and Internet addresses Identifies document titles

code text Identifies CLI output

Identifies syntax examples

For readability, command names in the narrative portions of this guide are presented in mixed lettercase: for example, switchShow. In actual examples, command lettercase is often all lowercase. Otherwise, this manual specifically notes those cases in which a command is case sensitive.

Notes, cautions, and warnings

The following notices and statements are used in this manual. They are listed below in order of increasing severity of potential hazards.

NOTE

A note provides a tip, guidance or advice, emphasizes important information, or provides a reference to related information.

ATTENTION

An Attention statement indicates potential damage to hardware or data.

CAUTION A Caution statement alerts you to situations that can be potentially hazardous to you or cause

damage to hardware, firmware, software, or data.

DANGER

A Danger statement indicates conditions or situations that can be potentially lethal or extremely hazardous to you. Safety labels are also attached directly to products to warn of these conditions or situations.

Key terms

For definitions specific to Brocade and Fibre Channel, see the technical glossaries on Brocade Connect. See “Brocade resources” on page xv for instructions on accessing Brocade Connect.

xiv Fabric OS MIB Reference

53-1001339-01

For definitions of SAN-specific terms, visit the Storage Networking Industry Association online dictionary at:

http://www.snia.org/education/dictionary

Notice to the reader

This document may contain references to the trademarks of the following corporations. These trademarks are the properties of their respective companies and corporations.

These references are made for informational purposes only.

Corporation Referenced Trademarks and Products

Microsoft Corporation Windows, Windows NT, Internet Explorer

Sun Microsystems, Inc. Sun, Solaris

Additional information

This section lists additional Brocade and industry-specific documentation that you might find helpful.

Brocade resources

To get up-to-the-minute information, go to http://my.brocade.com and register at no cost for a user ID and password.

For practical discussions about SAN design, implementation, and maintenance, you can obtain

Building SANs with Brocade Fabric Switches through:

http://www.amazon.com

White papers, online demos, and data sheets are available through the Brocade Web site at:

http://www.brocade.com/products-solutions/products/index.page

For additional Brocade documentation, visit the Brocade Web site:

http://www.brocade.com

Release notes are available on the Brocade Connect Web site and are also bundled with the Fabric OS firmware.

Other industry resources

For additional resource information, visit the Technical Committee T11 Web site. This Web site provides interface standards for high-performance and mass storage applications for Fibre Channel, storage management, and other applications:

http://www.t11.org

Fabric OS MIB Reference xv 53-1001339-01

For information about the Fibre Channel industry, visit the Fibre Channel Industry Association Web site:

http://www.fibrechannel.org

Getting technical help

Contact your switch supplier for hardware, firmware, and software support, including product repairs and part ordering. To expedite your call, have the following information immediately available:

1. General Information

• Switch model

• Switch operating system version

• Software name and software version, if applicable

• Error numbers and messages received

• supportSave command output

• Detailed description of the problem, including the switch or fabric behavior immediately

following the problem, and specific questions

• Description of any troubleshooting steps already performed and the results

• Serial console and Telnet session logs

• syslog message logs

2. Switch Serial Number

The switch serial number and corresponding bar code are provided on the serial number label, as shown here:

*FT00X0054E9*

FT00X0054E9

The serial number label is located as follows:

• Brocade 300, 4100, 4900, 5100, 5300, 7500, 7800, 8000, and Brocade Encryption

Switch—On the switch ID pull-out tab located inside the chassis on the port side on the left

• Brocade 5000—On the switch ID pull-out tab located on the bottom of the port side of the

switch

• Brocade 7600—On the bottom of the chassis

• Brocade 48000—Inside the chassis next to the power supply bays

• Brocade DCX—On the bottom right on the port side of the chassis

• Brocade DCX-4S—On the bottom right on the port side of the chassis, directly above the

cable management comb.

3. World Wide Name (WWN)

Use the licenseIdShow command to display the WWN of the chassis.

xvi Fabric OS MIB Reference

53-1001339-01

• If you cannot use the licenseIdShow command because the switch is inoperable, you can

get the WWN from the same place as the serial number, except for the Brocade DCX. For the Brocade DCX, access the numbers on the WWN cards by removing the Brocade logo plate at the top of the nonport side of the chassis.

Document feedback

Because quality is our first concern at Brocade, we have made every effort to ensure the accuracy and completeness of this document. However, if you find an error or an omission, or you think that a topic needs further development, we want to hear from you. Forward your feedback to:

documentation@brocade.com

Provide the title and version number and as much detail as possible about your comment, including the topic heading and page number and your suggestions for improvement.

Fabric OS MIB Reference xvii 53-1001339-01

xviii Fabric OS MIB Reference

53-1001339-01

Chapter

Understanding Brocade SNMP

In this chapter

•Setting the SNMP security level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

•Understanding SNMP basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

•Loading Brocade MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

•Brocade 7500 / FR4-18i and Brocade MIBs. . . . . . . . . . . . . . . . . . . . . . . . . 13

•Firmware upgrades and enabled traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

•Fabric OS commands for configuring SNMP . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the SNMP security level

The Simple Network Management Protocol (SNMP) is an industry-standard method of monitoring and managing network devices. This protocol promotes interoperability because SNMP-capable systems must adhere to a common set of framework and language rules.

Understanding the components of SNMP makes it possible to use third-party tools to view, browse, and manipulate Brocade switch variables (MIBs) remotely as well as to set up an enterprise-level management process. Every Brocade switch and director supports SNMP.

Recipients for SNMP traps are restricted according to security levels. Security levels are selected and set for a switch using the snmpconfig --set seclevel command. To select and set SNMP security levels, issue the command snmpconfig --set seclevel after having logged in to the switch as admin.

The following example sets the SNMP security level to 1 (authentication only). This setting allows all SNMPv1 users to perform GET and SET operations on MIBs, but creates an exception for SNMPv3 users that do not have authentication and privacy privileges (noAuthnoPriv).

switch:admin> snmpconfig --set seclevel Select SNMP Security Level (0 = No security, 1 = Authentication only, 2 = Authentication and Privacy, 3 = sxNo Access): (0..3) [0] Select SNMP SET Security Level (0 = No security, 1 = Authentication only, 2 = Authentication and Privacy, 3 = No Access): (0..3) [0]

TABLE 1 Security level options

Security level Protocol Query behavior Traps

No security [0] (noAuthnoPriv)

Authentication only [1] (authNoPriv)

SNMPv1 SNMPv3

Allowed. Allowed.

Allowed. All SNMPv3 users allowed except

noAuthNoPriv users.

Sent. Sent.

Sent. Sent for all SNMPv3 users

except noAuthNoPriv users.

Fabric OS MIB Reference 1 53-1001339-01

Understanding SNMP basics

TABLE 1 Security level options (Continued)

Security level Protocol Query behavior Traps

Authentication and Privacy [2]

(authPriv)

No Access [3]SNMPv1

SNMPv1 SNMPv3

SNMPv3

Understanding SNMP basics

Every Brocade switch carries an agent and management information base (MIB), as shown in

Figure 1. The agent accesses information about a device and makes it available to an SNMP

network management station.

Management Station

FIGURE 1 SNMP structure

When active, the management station can get information or set information when it queries an agent. SNMP commands, such as get, set, getnext, setnext, and getresponse, are sent from the management station, and the agent replies once the value is obtained or modified (Figure 2). Agents use variables to report such data as the number of bytes and packets in and out of the device, or the number of broadcast messages sent and received. These variables are also known as managed objects. All managed objects are contained in the MIB.

Not allowed. Only SNMPv3 users with authPriv

privilege are allowed.

Not allowed. Not Sent.

SNMP

Agent

Not Sent. Sent only for authPriv users.

MIB

get, getnext, se

Management Station

Agent

FIGURE 2 SNMP query

The management station can also receive traps, unsolicited messages from the switch agent if an unusual event occurs. Refer to “Understanding SNMP traps” on page 4 for more information.

Management Station

TRAP

Agent

FIGURE 3 SNMP trap

The agent can receive queries from one or more management stations and can send traps to up to six management stations.

2 Fabric OS MIB Reference

53-1001339-01

Understanding SNMP basics

Understanding MIBs

The management information base (MIB) is a database of monitored and managed information on a device, in this case a Brocade switch. The MIB structure can be represented by a tree hierarchy. The root splits into three main branches: International Organization for Standardization (ISO), Consultative Committee for International Telegraph and Telephone (CCITT), and joint ISO/CCITT. These branches have short text strings and integers (OIDs) to identify them. Text strings describe object names, while integers allow software to create compact, encoded representations of the names.

Each MIB variable is assigned an object identifier (OID). The OID is the sequence of numeric labels on the nodes along a path from the root to the object. For example, as shown in Figure 4, the Brocade SW.MIB OID is:

1.3.6.1.4.1.1588

The corresponding name is:

iso.org.dod.internet.private.enterprise.bsci

The other branches are part of the standard MIBs, and the portions relevant to configuring SNMP on a Brocade switch are referenced in the remainder of this reference.

iso (1)

org (3)

Brocade SW MIB

1.3.6.1.4.1.1588

private (4)

enterprise (1)

bcsi (1588)

directory (1)

sysDescr (1)

system (1)

mgmt (2)

mib-2 (1)

interface (2)

sysObjectID (2)

dod (6)

internet (1)

experimental (3)

fibreChannel (42)

fcFe (1)

fcFabric (2)

FIGURE 4 Brocade MIB tree location

Use a MIB browser to access the MIB variables: all MIB browsers perform queries and load MIBs.

Since different vendors vary the information in their private enterprise MIBs, it is necessary to verify their information. The Fibre Channel MIB standards dictate that certain information be included in all MIBs: it is the vendors’ responsibility to follow the standards. The standards are as follows:

• FibreAlliance (FA) MIB: Brocade supports version 3.0.

Fabric OS MIB Reference 3 53-1001339-01

Understanding SNMP basics

• Fabric Element (FE) MIB: accepted by the Internet Engineering Task Force (IETF).

Once loaded, the MAX-ACCESS provides access levels between the agent and management station. The access levels are as follows:

• not-accessible

• read-create

• read-only - Public

• read-write - Private

Brocade supports FE_RCF2837.mib under the MIB-II branch in Fabric OS v6.3.0, v6.2.0, v6.1.2_CEE, v6.1.0, v6.0.0, v4.x, v3.2.0, and v3.1.x and the experimental version, FE_EXP.mib, in Fabric OS v2.6.x and 3.0.x. This latest version of the FE MIB references the FRAMEWORK.MIB and, based on the MIB browser, it is necessary to load this MIB before the FE.MIB. Refer to “Loading Brocade MIBs” on page 6 for more information.

You cannot read or write to this variable.

Specifies a tabular object that can be read, modified, or created as a new row in a table.

You can only monitor information.

You can read or modify this variable.

Understanding SNMP traps

An unsolicited message that comes to the management station from the SNMP agent on the device is called a trap. Brocade switches send traps out on UDP port 162 and to any configured port. In order to receive traps, the management station IP address and severity level must be configured on the switch. Up to six trap recipients can be configured using Web Tools or the snmpConfig command. You can define a different message severity level for each recipient so that some recipients receive all trap messages and others receive only the most critical.

There are two main MIB trap choices:

• FibreAlliance MIB trap - Associated with the Fibre Alliance MIB (FA-MIB), this MIB manages SAN

switches and devices from any company that complies with Fibre Alliance specifications.

• Brocade-specific MIB trap - Associated with the Brocade-specific Brocade MIB (SW-MIB),

manages Brocade switches only.

There is some overlap in the functionality of these MIBs. If you enable both SW-MIB and FA-MIB traps, you could receive duplicate messages for the switch events that trigger the trap.

You can also use these additional MIBs and their associated traps: HA-MIB; FICON-MIB; and SW-EXTTRA. You can use the snmpConfig command to disable the FA-MIB, HA-MIB, FICON-MIB, and SW_EXTTRA; but neither the SW-MIB or the FE-MIB can be disabled.

An event trap (swEventTrap, connUnitEventTrap, or swFabricWatchTrap) is basically an error message (errShow output) that is SNMP-formatted and delivered.

FA traps

Consider enabling the FA traps if you want to use SNMP to monitor multiple connectivity units, including Brocade switches.

The switchStatusPolicySet command determines the FA-TRAP switch status-related outputs:

• connUnitStatusChange

4 Fabric OS MIB Reference

53-1001339-01

Understanding SNMP basics

• connUnitSensorStatusChange

• connUnitPortStatusChange

• connUnitEventTrap

The MIB-II system description swEventTrapLevel determines the output for the connUnitEventTrap. Events in the Error Log of a severity at or above the configured threshold will generate SNMP traps.

The Fibre Alliance Trap (FA-TRAP) can be configured to send traps using the snmpConfig command. Refer to the Fabric OS Command Reference for more information on this command.

HA traps

Consider enabling these traps to monitor field-replaceable unit (FRU) status and control processor (CP) status when you have a Brocade director in your environment:

• fruStatusChanged

This trap is generated by a FRU status change, such as a switch reboot or disabling or enabling a FRU component such as (fandisable or fanenable, etc).

• cpStatusChanged

This trap is generated by a change in the status of a CP, including a reboot or firmware download.

• fruHistoryTrap

This trap is generated when a FRU is added or removed. fruHistoryTrap is not generated when standby CP is removed.

The high availability trap (HA-TRAP) can be configured to send traps using the snmpConfig command. Refer to the Fabric OS Command Reference for more information on this command.

SW traps

There are six specific traps defined in Brocade SW-TRAP.

1. swfault (no longer supported)

2. swSensorScn (no longer supported)

3. swFCPortScn

This trap is generated by a port state change.

4. swEventTrap

This trap is generated by any switch event reported to the system error log.

5. swFabricWatchTrap

This trap is generated when any Fabric Watch threshold is reached.

6. swTrackChangesTrap

This trap is generated by a login or a logout.

7. swPmgrEventTrap

This trap is generated when an IPv6 address status change event occurs.

8. swIpv6ChangeTrap

Fabric OS MIB Reference 5 53-1001339-01

Loading Brocade MIBs

This trap is generated when any partition manager change happens.

The Brocade trap (SW-TRAP) can be configured to send traps using the snmpConfig command. Refer to the Fabric OS Command Reference for more information on this command.

Object instances

MIB objects are defined by the OID, which is the type of object, and by the instance number, which is an instance of that MIB object. A Fibre Channel port is a MIB object, and port 0 is an instance of that object. The following is an OID number and an instance number:

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11.5

where:

1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11 is the OID (of swFCPortTxWords) and 5 is the instance

ID for port 4.

You must add 1 to the port number to get its instance number in SNMP because SNMP numbering starts at 1; switch port numbering starts at 0.

Loading Brocade MIBs

The Brocade MIB is a set of variables that are private extensions to the Internet standard MIB-II. The Brocade agents support many other Internet-standard MIBs. These standard MIBs are defined in RFC publications. To find specific MIB information, examine the Brocade proprietary MIB structure and the standard RFC MIBs supported by Brocade.

Brocade MIB files

The Brocade MIB files are as follows:

• BRCD_v5_0.mib

• brcdfcip.mib

• CPQ_HOST.mib

• CPQ_RACK.mib

• ENTITY_RFC2737.mib

• FA_v3_0.mib

• fcip.mib

• FE_RFC2837.mib

• FICON_v5_0.mib

• HA_v5_1.mib

• IF.mib

• IF_TYPE.mib

• INET_ADDR.mib

• ISCSI_RFC4544.mib

• SW_v5_7.mib

• RMON.mib

6 Fabric OS MIB Reference

53-1001339-01

Loading Brocade MIBs

• usm.mib

Before loading MIBs

Before loading Brocade MIB files, ensure that you have the correct version of SNMP for your Fabric OS version (Table 2).

TABLE 2 Fabric OS supported SNMP versions

Firmware SNMPv1 SNMPv2 SNMPv3

Fabric OS v2.6.2 and previous Yes No

Fabric OS v3.2.0 and previous Yes No

Fabric OS v4.2.0 and previous Yes No

Fabric OS v4.4.0 Yes No

Fabric OS v5.x Yes Yes

Fabric OS v6.0.0 Yes Yes Yes

Fabric OS v6.1.0 Yes Yes Yes

Fabric OS v6.2.0 Yes Yes Yes

Fabric OS v6.1.2_CEE Yes No Yes

Fabric OS v6.3.0 Yes No Yes

Yes

1. The corresponding Fabric OS has SNMPv2 capabilities, but it is not officially supported by Brocade.

2. Fabric OS v4.4.0 and v5.x support SNMPv3-USM MIB (snmpUsmMIB), which is available as RFC 3414.

3. SNMPv2 is supported from Fabric OS v5.0.4 and higher, but SNMP v2 traps are not supported.

MIB loading order

Many MIBs use definitions that are defined in other MIBs. These definitions are listed in the IMPORTS section near the top of the MIB. When loading the Brocade MIBs, refer to Figure 5 to ensure any MIB dependencies are loading in the correct order.

Fabric OS MIB Reference 7 53-1001339-01

Loading Brocade MIBs

RFC1213-MIB

MIB-II

RFC1155-SMI

SNMPv2-SMI

SMNPv2-TC

SNMPv2-CONF

RMON MIB

Select one

FA_v2_2.mib

FCMGMT-MIB

FOS 2.6.x

FA.mib

FCMGMT-MIB

FOS 3.x, 4.x, 5.x, 6.x

BRCD.mib

Brocade-REG-MIB

Brocade-TC

FOS 2.6.x, 3.x, 4.x, 5.x, 6.x

INET-ADDRESS-MIB

snmpUsmMIB

User-based Security Model

SNMP-FRAMEWORK-MIB

FC_RFC4044.mib

ISCSI_RFC4544.mib

RFC2571

Legend

Select one or both

FCFABRIC-ELEMENT-MIB

FE_RFC2837.mib

FIBRE-CHANNEL-FE-MIB

FOS 3.1.x, 4.x, 5.x, 6.x

FICON_v5_0.mib

FOS 4.x, 5.x, 6.x

SW_v5_5.mib

FOS 2.6.x, 3.x, 4.x, 5.x

SW_v5_7.mib

ENTITY_RFC2737.mib

FOS 4.x, 5.x, 6.x

FCIP.mib

FOS 6.2 and 6.3

brcdfcip.mib

FE_EXP.mib

FICON-MIB

FOS 6.x

SW.mib

FOS 6.x

ENTITY-MIB

HA.mib

FOS 4.x, 5.x, 6.x

Brocade MIB

Module name

FOS supported

IF.mib

FOS 5.3 and 6.x

Standard MIB File

Module name

Dependency

NOTE

FA_v3_0.mib obsoletes the use of the connUnitPortStatFabricTable used in the FA_v2_2.mib. FA_v3_0.mib now uses the connUnitPortStatTable for port statistics. The FA_v3_0.mib and the FA_v2_2.mib cannot be loaded concurrently on the same SNMP management system.

The FE_RFC2837.mib and the FE_EXP.mib can be loaded concurrently on the same SNMP management system. The FE_EXP.mib was listed in the experimental OID section. The FE_RFC2837.mib has subsequently been ratified by the standards organizations.|

All versions of Fabric OS support SNMPv1. Fabric v2.6.x and v3.2.x partially support SNMPv2. Fabric OS v4.4.0 and v5.0.1 support SNMPv3-USM (snmpUsmMIB) MIB. Fabric OS version 5.3.0 supports the FCIP MIB and ifXtable.

FIGURE 5 Brocade SNMP MIB dependencies and advised installation order

8 Fabric OS MIB Reference

53-1001339-01

Loading Brocade MIBs

SNMP CLI usage

An example of the SNMPv3 User/Traps configuration is provided below.

Configuring SNMPv3 user/traps

1. Create user on switch using CLI userconfig, with the required role.

switch:admin> userconfig --add fa_adm -r fabricadmin -h0 -a 0-255 Setting initial password for fa_adm Enter new password:******** Re-type new password:******** Account fa_adm has been successfully added. switch:admin>

Create user on switch in VF Context using CLI userconfig, with the required role.

switch:admin> userconfig --add sa_user -r switchadmin -l 1-128 -h1 -c admin Setting initial password for sa_user Enter new password:******** Re-type new password:******** Account sa_user has been successfully added. switch:admin>

2. Create the SNMPv3 user as shown below.

DCX_54:root> snmpconfig --set snmpv3

SNMP Informs Enabled (true, t, false, f): [false] t

SNMPv3 user configuration(snmp user not configured in FOS user database will have physical AD and admin role as the default): User (rw): [snmpadmin1] Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3] Priv Protocol [DES(1)/noPriv(2)/3DES(3)/AES128(4)/AES192(5)/AES256(6)]): (2..2) [2] Engine ID: [0:0:0:0:0:0:0:0:0] 80:00:05:23:01:0A:23:34:21 User (rw): [snmpadmin2] Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3] 1 New Auth Passwd: Verify Auth Passwd: Priv Protocol [DES(1)/noPriv(2)/3DES(3)/AES128(4)/AES192(5)/AES256(6)]): (1..6) [2] 1 New Priv Passwd: Verify Priv Passwd: Engine ID: [0:0:0:0:0:0:0:0:0] 80:00:05:23:01:0A:23:34:1B User (rw): [snmpadmin3] Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3] Priv Protocol [DES(1)/noPriv(2)/3DES(3)/AES128(4)/AES192(5)/AES256(6)]): (2..2) [2] Engine ID: [0:0:0:0:0:0:0:0:0] User (ro): [snmpuser1] Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3] Priv Protocol [DES(1)/noPriv(2)/3DES(3)/AES128(4)/AES192(5)/AES256(6)]): (2..2) [2] Engine ID: [0:0:0:0:0:0:0:0:0] User (ro): [snmpuser2] Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3] Priv Protocol [DES(1)/noPriv(2)/3DES(3)/AES128(4)/AES192(5)/AES256(6)]): (2..2) [2]

Fabric OS MIB Reference 9 53-1001339-01

Loading Brocade MIBs

Engine ID: [0:0:0:0:0:0:0:0:0] User (ro): [snmpuser3] Auth Protocol [MD5(1)/SHA(2)/noAuth(3)]: (1..3) [3] Priv Protocol [DES(1)/noPriv(2)/3DES(3)/AES128(4)/AES192(5)/AES256(6)]): (2..2) [2] Engine ID: [0:0:0:0:0:0:0:0:0]

SNMPv3 trap recipient configuration: Trap Recipient's IP address : [0.0.0.0] 10.35.52.33 UserIndex: (1..6) [1] Trap recipient Severity level : (0..5) [0] 4 Trap recipient Port : (0..65535) [162] Trap Recipient's IP address : [0.0.0.0] 10.35.52.27 UserIndex: (1..6) [2] Trap recipient Severity level : (0..5) [0] 4 Trap recipient Port : (0..65535) [162] Trap Recipient's IP address : [0.0.0.0] Trap Recipient's IP address : [0.0.0.0] Trap Recipient's IP address : [0.0.0.0] Trap Recipient's IP address : [0.0.0.0]

Committing configuration.....done.

DCX_54:root> DCX_54:root> snmpconfig --show snmpv3

SNMP Informs = 1 (ON)

SNMPv3 USM configuration: User 1 (rw): snmpadmin1 Auth Protocol: noAuth Priv Protocol: noPriv Engine ID: 80:00:05:23:01:0a:23:34:21 User 2 (rw): snmpadmin2 Auth Protocol: MD5 Priv Protocol: DES Engine ID: 80:00:05:23:01:0a:23:34:1b User 3 (rw): snmpadmin3 Auth Protocol: noAuth Priv Protocol: noPriv Engine ID: 00:00:00:00:00:00:00:00:00 User 4 (ro): snmpuser1 Auth Protocol: noAuth Priv Protocol: noPriv Engine ID: 00:00:00:00:00:00:00:00:00 User 5 (ro): snmpuser2 Auth Protocol: noAuth Priv Protocol: noPriv Engine ID: 00:00:00:00:00:00:00:00:00 User 6 (ro): snmpuser3 Auth Protocol: noAuth Priv Protocol: noPriv Engine ID: 00:00:00:00:00:00:00:00:00

SNMPv3 Trap configuration: Trap Entry 1: 10.35.52.33 Trap Port: 162 Trap User: snmpadmin1 Trap recipient Severity level: 4 Trap Entry 2: 10.35.52.27 Trap Port: 162

10 Fabric OS MIB Reference

53-1001339-01

Loading Brocade MIBs

Trap User: snmpadmin2 Trap recipient Severity level: 4 Trap Entry 3: No trap recipient configured yet Trap Entry 4: No trap recipient configured yet Trap Entry 5: No trap recipient configured yet Trap Entry 6: No trap recipient configured yet DCX_54:root>

SNMP Notification Generator:

DCX_54:root> snmpTraps --show

# |Mib Name |Supported Traps

---|----------------|-------------------------------001|SW-MIB |sw-track-changes-trap | |sw-fabric-watch-trap | |sw-fault | |sw-fc-port-scn | |ip-v6-change-trap | |sw-pmgr-event-trap | |sw-event-trap 002|FICON-MIB |link-rnid-device-registration | |link-rnid-device-deregistration | |link-lirr-listerner-added | |link-lirr-listerner-removed 003|FA-MIB |conn-unit-status-change | |conn-unit-sensor-status-change | |conn-unit-port-status-change 004|RFC1157 |cold-restart-trap | |warm-restart-trap | |if-link-up-trap | |if-link-down-trap | |snmp-authetication-trap 005|HA-MIB |fru-status-change-trap | |fru-history-trap | |cp-status-change-trap DCX_54:root> snmpTraps --send Number of traps sent : 22 DCX_54:root> snmpTraps --send -ip_address 10.35.52.33 Number of traps sent : 22 DCX_54:root> snmpTraps --send -trap_name sw-fc-port-scn Number of traps sent : 1 DCX_54:root> snmpTraps --send -trap_name sw-fc-port-scn -ip_address

10.35.52.33 Number of traps sent : 1 DCX_54:root>

Example of accessControl configuration switch:admin> snmpconfig --set accessControl SNMP access list configuration: Access host subnet area in dot notation: [0.0.0.0] 192.168.0.0 Read/Write? (true, t, false, f): [true] Access host subnet area in dot notation: [0.0.0.0] 10.32.148.0 Read/Write? (true, t, false, f): [true] f Access host subnet area in dot notation: [0.0.0.0] Read/Write? (true, t, false, f): [true] Access host subnet area in dot notation: [0.0.0.0] 10.33.0.0 Read/Write? (true, t, false, f): [true] f Access host subnet area in dot notation: [0.0.0.0] Read/Write? (true, t, false, f): [true]

Fabric OS MIB Reference 11 53-1001339-01

Loading Brocade MIBs

Access host subnet area in dot notation: [0.0.0.0] Read/Write? (true, t, false, f): [true] Committing configuration...done.

Example of mibCapability configuration DCX:admin> snmpconfig --show mibcapability FE-MIB:YES SW-MIB: YES FA-MIB: YES FICON-MIB: YES HA-MIB: YES FCIP-MIB: YES ISCSI-MIB: NO SW-TRAP: YES swFCPortScn: YES swEventTrap: YES swFabricWatchTrap: YES swTrackChangesTrap: YES FA-TRAP: YES connUnitStatusChange: YES connUnitEventTrap: YES connUnitSensorStatusChange: YES connUnitPortStatusChange: YES SW-EXTTRAP: NO FICON-TRAP: YES linkRNIDDeviceRegistration: YES linkRNIDDeviceDeRegistration: YES linkLIRRListenerAdded: YES linkLIRRListenerRemoved: YES linkRLIRFailureIncident: YES HA-TRAP: YES fruStatusChanged: YES cpStatusChanged: YES fruHistoryTrap: YES FCIP-TRAP: NO

Example of systemGroup configuration (default) switch:admin> snmpconfig --default systemGroup ***** This command will reset the agent's system group configuration back to factory default ***** sysDescr = Fibre Channel Switch sysLocation = End User Premise sysContact = Field Support authTraps = 0 (OFF) ***** Are you sure? (yes, y, no, n): [no] y

3. Set the security level.

switch:admin> snmpconfig --set secLevel Select SNMP GET Security Level (0 = No security, 1 = Authentication only, 2 = Authentication and Privacy, 3 = No Access): (0..3) [0] 2 Select SNMP SET Security Level (0 = No security, 1 = Authentication only, 2 = Authentication and Privacy, 3 = No Access): (2..3) [2] 2 switch:admin> snmpconfig --show secLevel

12 Fabric OS MIB Reference

53-1001339-01

+ 324 hidden pages

Brocade Communications Systems 1606, AM866A - StorageWorks 8/8 Base SAN Switch, 8/24, 8/40, 8/8 Reference

Specifications and Main Features

Frequently Asked Questions

User Manual