Broan-NuTone BPDP130SS, BPDP136SS, BPDP142SS, BPDP148SS Installation Manual

For ADA compliance installation guidelines, please visit www.broan-nutone.com

Recommended Tools and Accessories
for Installation

• Measuring tape

• Phillips screwdriver no. 2

• Nut driver or socket 11/32”

• Flat blade screwdriver (to open knockout holes)

• Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut electrical access hole)

• 7/64” drill bit (to drill holes for EZ1 brackets mounting screws)

• 7” round duct plate, not included with BPDC Series (for 7’’ round vertical ducting installation,
part no.: SR680508)

• Wood shims (2) and wood screws (4) (required for standard installation to framed cabinet)

• Saw (to cut holes for ducted application)

• Sheet metal shears (ducted installation only, for duct adjustment)

• Pliers (ducted installation only, for duct adjustment)

• Metal foil duct tape (for ducted applications)

• Scissors (to cut metal foil duct tape)

• Pencil

• Wire stripper

• Strain relief, 1/2” diameter (to secure house wiring cable to the hood)

Install Ductwork (Ducted Installations Only)

ROOF CAP

SOFFIT

CABINET

HOOD

18" MIN - 30" MAX

ABOVE

COOKING SURFACE

NOTE: Distances over 30” are at the installer and user discretion.
1 ] Determine whether hood will discharge vertically (3¼” x 10” or 7” round),

or horizontally (3¼” x 10” only).

2 ] Decide where the ductwork will run between the hood and the outdoors.
3 ] Choose a straight, short duct run to allow the hood to perform most efficiently. Long duct

runs, elbows and transitions will reduce the performance of the hood. Use as few of them as
possible. When possible, use at least 2-foot straight runs before any turns. Larger ductwork
may be required for best performance with longer duct runs.

NOTE: To use 6” round ducting, install a 3¼” x 10” to 6” round transition (not included). The
performances may be affected.

4 ] Install wall cap or roof cap (sold separately); ensure there is no leak in house insulation.

Connect metal ductwork to cap and work back towards the hood location. Use 2” metal foil
duct tape to seal the joints between ductwork sections.

3¼" X 10" OR

7" ROUND DUCT

(FOR VERTICAL

DISCHARGE

HOUSE WIRING
(TOP OR BACK OF HOOD)

3¼" X 10" DUCT
(FOR HORIZONTAL DISCHARGE)

)

WALL CAP

INSTALLATION

INSTALLATION MANUAL

7

Contents

VERTICAL EXHAUST

VERTICAL EXHAUST

Before proceeding to the installation, check the contents of the box. If items are missing or
damaged, contact the manufacturer.

Make sure that the following items are included:

BPDC1 Series BPDP1 and NPDP1 Series

(2) GREASE FILTERS

(1) 3¼” X 10” DAMPER ASSEMBLY

Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.

Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.

NOTA: To be translated in Spanish.

Bend template along graduated
scale when installing to framed
cabinet.

C

Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en

8”

conséquence.

To be translated in Spanish.

C

L

7½”

10½”

14½”

C

Appuyer ce bord au mur arrière

(4) NO. 8-18 X 1/2”

M

(2) SHIELDED HALOGEN BULBS

(FIND INSIDE OF HOOD)

OMPONENTS

EZ1 C

MARK WHERE INDICATED

FOR THE APPROPRIATE SIZE DUCT OPENING

RECTANGULAR DUCTING7” ROUND DUCTING

OR

= 3¼” x 10”
= 3¼” x 14”

MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON

LE FORMAT DE CONDUIT UTILISÉ

CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO

OU

= 3¼ po x 10 po
= 3¼ po x 14 po

TITLE TO BE TRANSLATED IN SPANISH

CONDUCTO RECTANGULARCONDUCTO REDONDO

O

= 3¼ pulg. x 10 pulg.

7 PULG.

DE

= 3¼ pulg. x 14 pulg.

Electrical access hole center

A = single blower hood
B = double blower hood

Centre du trou pour fil
d’alimentation électrique

A = hotte ventilateur simple
B = hotte ventilateur double

To be translated in Spanish
Electrical access hole center

4¼”

A = single blower hood
B = double blower hood

AB

C

Apoyar este borde contra la pared de atrásPlace this edge against back wall

ARTS BAG** CONTAINING:

(1) P

ETAL SCREWS

(50W, GU10)

(1) TEMPLATE FOR DUCTING

(PRINTED BOTH SIDES)

(2) INSTALLATION BRACKETS*

FOR FRAMED CABINET

(2) INSTALLATION BRACKETS*

FOR FRAMELESS CABINET

* FIND EZ1 BRACKET

INSIDE OF HOOD

ATTACHED

(6) NO. 8 X 1/2”

C

OUNTERSUNK

WOOD SCREWS

(2) GREASE FILTERS

Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.

Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.

NOTA: To be translated in Spanish.

Bend template along graduated
scale when installing to framed
cabinet.

C

Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en

8”

conséquence.

To be translated in Spanish.

C

L

7½”

10½”

14½”

C

Appuyer ce bord au mur arrière

** FIND EZ1 BRACKETS ATTACHED INSIDE OF HOOD

(6) N

RD. HD.

W

OOD SCREWS

* FIND INSIDE ONE PACK AGING

STYROFOAM

OF HOOD

(1) 3¼” X 10”

D

AMPER ASSEMBLY*

EZ1 C

MARK WHERE INDICATED

FOR THE APPROPRIATE SIZE DUCT OPENING

MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON

LE FORMAT DE CONDUIT UTILISÉ

TITLE TO BE TRANSLATED IN SPANISH

Apoyar este borde contra la pared de atrásPlace this edge against back wall

OMPONENTS

RECTANGULAR DUCTING7” ROUND DUCTING

OR

= 3¼” x 10”
= 3¼” x 14”

CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO

OU

= 3¼ po x 10 po
= 3¼ po x 14 po

CONDUCTO RECTANGULARCONDUCTO REDONDO

O

= 3¼ pulg. x 10 pulg.

DE

7 PULG.

= 3¼ pulg. x 14 pulg.

4¼”

(1) TEMPLATE FOR DUCTING

Electrical access hole center

A = single blower hood
B = double blower hood

Centre du trou pour fil
d’alimentation électrique

A = hotte ventilateur simple
B = hotte ventilateur double

To be translated in Spanish
Electrical access hole center

A = single blower hood
B = double blower hood

AB

C

(PRINTED BOTH SIDES)

(2) INSTALLATION BRACKETS**

FOR FRAMED CABINET

(2) INSTALLATION BRACKETS**

FOR FRAMELESS CABINET

(1) P

ARTS BAG*** CONTAINING:

(4) NO. 8-18 X 1/2”

M

ETAL SCREWS

O. 8 X 5/8”

*** FIND PAR T S BAG INSIDE OF HOOD

(1) 7” ROUND

DUCT CONNECTOR

(6) NO. 8 X 1/2”

C

OUNTERSUNK

WOOD SCREWS

INSTALLATION MANUAL

8

INSTALLATION

(6) NO. 8 X 5/8”

RD. HD.

W

OOD SCREWS

** FIND PAR T S BAG INSIDE OF HOOD

(1) B

CUP TOOL

ULB SUCTION

Prepare the Hood

1 ] If present, remove all protective polyfilm from the hood and/or parts.

2 ] Using the finger cup, remove the grease filters from the hood by pushing down  and tilting

filters out .

B

C

3 ] Remove both fillers by removing the 3 screws holding each one of them. Slide each one

towards the center of the hood and tilt it up to remove it completely. Set the fillers and screws
aside.

c

d

INSTALLATION

INSTALLATION MANUAL

9

4 ] Remove both tape strips holding the 7” round adapter (not included with BPDC Series), and

put the adapter aside.

5 ] Remove the screw holding the 3¼” x 10” adapter/damper and put the adapter/damper aside.

Save this screw, it will be used later to hold the cover plate.

6 ] Remove the parts bag taped in the lower left corner of the hood.

TAPE

REMOVE
AND SAVE

TAPE

PARTS BAG

7 ] Using a 11/32” nut driver or socket, remove the lock nut retaining the flange of the right cover

plate (shaded part on illustration below) to the inner back of hood (see inset). Remove the
right cover plate retaining screws (7 screws), then set the blower cover along with its screws
and nut aside.

NOTE: For 30 in.-wide hoods, slightly lift up the cover plate before sliding it towards the left to

remove it.

TAPE

THIS
SCREW

6

7

BACK OF HOOD

LOCK NUT

45

3

1

2

SCREW REMOVED

IN STEP 5

INSTALLATION MANUAL

10

INSTALLATION

8 ] Remove the EZ1 brackets from inside the hood by cutting off the tie wrap. Discard the tie

wrap.

EZ1

BRACKETS

9 ] Remove Electrical Power Cable Knockout from top (vertical wiring) or back (horizontal wiring)

of hood. For knockout removed from back of hood, install an appropriate strain relief,
1/2” diameter (not included). For knockout removed from top of hood, the strain relief will be
installed later.

ELECTRICAL

POWER CABLE

KNOCKOUT

NON-DUCTED INSTALLATION ONLY

10 ] Remove the 3 screws retaining the recirculation cover plate to the hood. Discard this plate

with its screws.

11 ] Peel off and discard the membrane covering the recirculation grille, ensuring the openings

are totally cleared.

RECIRCULATION

COVER PLATE

SCREWS

INSTALLATION

INSTALLATION MANUAL

11