Broan XB110L1, XB80L1, XB50L1 Installation Manual

READ AND SAVE THESE INSTRUCTIONS

Installer: leave this guide with homeowner.

XB50L1

XB80L1 n XB110L1

X1 | Single-Speed Ventilation Fan with Dimmable Light

INSTALLATION GUIDE

Easy installation in both new construction and retrofit

Table of Contents

Warnings and Cautions 2 Typical Installation 2 New Construction Installation 3 Retrofit Installation 7 Operation 12 Cleaning and Maintenance 12 Troubleshooting 12 Service Parts 13 Warranty 13

Page 2

XB50L1

XB80L1

XB110L1 Installation Guide

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Use only ON/OFF switch, mechanical timer or relay-switched control.

8. Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

9. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. This product is designed for installation in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must point up.

DO NOT MOUNT THIS PRODUCT IN A WALL.

3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

4. Please read specification label on product for further information and requirements.

NOT FOR USE IN A COOKING AREA

Do not install above or inside this area

45° 45°

Cooking Equipment

Floor

Typical Installation

• Installation is the same for:

Joists I-Joists Trusses

• Fits in 2" x 8" ceiling construction.

• Infinitely adjust the fan position between joists from 14" to 24" on center.

• Do not install this fan in a ceiling thermally insulated to a value greater than R40.

The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and energy use of the fan. Use the shortest, straighest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated airflow.

6-inch round rigid metal duct is recommended for best performance.

HOUSING

POWER CABLE*

Seal gaps

around

Housing.

*Purchase separately.

INSULATION*

(Place around and

over Fan Housing.)

FAN

ROUND

DUCT*

Seal duct

joints with

tape.

ROUND

ELBOWS*

ROOF CAP*

(with built-in

damper)

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

Page 3

New Construction Installation

XB50L1

XB80L1

XB110L1 Installation Guide

Tools needed

• Power screwdriver with a Phillips bit

• Phillips screwdriver

• Flathead screwdriver

• Pliers

• Wire insulation stripper

• Wire cutter

Remove Packaging

Parts Bag holds Knockout Plate and six (6) screws

Materials needed

• 6" round metal ducting recommended for best performance. Use of other ducting is acceptable but may impact performance.

• Roof cap or wall cap (built-in damper recommended)

• Tape to seal duct connections

• Electrical wiring and supplies per local code requirements

Punch out Mask from

packaging. See Step 6. Remove Instruction Sheet

Install

Mounting Frame

Page 4

New Construction Installation

Snap-in and

Secure Housing

snap!

XB50L1

XB80L1

XB110L1 Installation Guide

Attach Duct Connector and Ducting

Top and bottom flanges go outside Housing

Insert tab into slot inside Housing

6" Ducting

Tape

Screws from Parts Bag

4" Ducting

Tape

Position Housing between joists and crimp channel on both sides of Mounting Frame to lock Housing in place.

Do not crimp Housing.

Screw from

Parts Bag

Tape

6" to 4" Reducer provided in select models

Page 5

New Construction Installation

Connect Wires and Install Knockout Plate

• Run 120VAC electrical wiring to the installation location.

• Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

Attach cable clamps to

Knockout Plate. Knockout

Plate mounts to outside of

Housing and may be

oriented as desired.

XB50L1

XB80L1

XB110L1 Installation Guide

LINE

LIGHT

SWITCH

FAN

SWITCH

BLK WHT GRD

Connect wires

LIGHT WITH ON/OFF SWITCH

RED BLU

BLK

WHT GRD

BLK

LIGHT

FAN

UNITSWITCH BOX

Screw from

Parts Bag

WHT

RED

WHT

LINE

BLK

WHT

GRD

DIMMER SWITCH

LIGHT WITH DIMMER SWITCH

RED BLU

FAN

SWITCH

BLK

WHT

GRD

BLK

LIGHT

FAN

UNITSWITCH BOX

WHT

RED

WHT

Page 6

New Construction Installation

Insert Mask and

Finish Ceiling

• Install ceiling material.

• Cut out around Housing.

CAUTION

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

If the blower was unplugged, power must be disconnected (see page 2, WARNING item 2) before inserting motor plugs into control assembly.

XB50L1

XB80L1

XB110L1 Installation Guide

Mask protects unit

during construction.

Remove before installing Grille.

Install Grille

See Page 12 for Operations, Cleaning and Maintenance, and Troubleshooting.

Page 7

Retrofit Installation

XB50L1

XB80L1

XB110L1 Installation Guide

Tools needed

• Power screwdriver with a Phillips bit

• Phillips screwdriver

• Flathead screwdriver

• Pliers

• Wire insulation stripper

• Wire cutter

• Ruler

• Pencil

• Drywall saw

• Claw hammer or pry bar

• Utility knife

Materials needed

• Tape to seal duct connections

• Existing rigid duct will require the addition of a short length of flexible duct

• Electrical wiring and supplies per local code requirements

Remove Packaging

Remove Instruction Sheet

Parts Bag holds Knockout Plate and six (6) screws

Punch out Mask from

packaging. See Step 12.

Switch Off Power

WARNING

Before removing existing fan, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Enlarge Ceiling Opening and Remove Existing Fan

12" (30.5 cm)

11" (27.9 cm) parallel with joists

Existing ductwork and

Examine Wiring

Examine the existing wiring to make sure it is not damaged. If any damage is found, DO NOT CONTINUE INSTALLATION of this product. Contact a qualified person(s) for repair.

wiring left in place

Page 8

Retrofit Installation

Remove Blower Assembly

XB50L1

XB80L1

XB110L1 Installation Guide

Set aside Blower Assembly

Both sides

Remove Wiring Panel

Set aside Wiring Panel

Set aside screw

Insert

Mounting Frame

Remove screws from Mounting Frame and set aside

Bend up four tabs

Page 9

Retrofit Installation

Secure

Mounting Frame

Snap-in Housing

Screws set

aside

in Step 7

XB50L1

XB80L1

XB110L1 Installation Guide

Pull existing ductwork into Housing

Pull existing wiring into Housing as it is inserted into Mounting Frame

snap!

Attach Ducting and Duct Connector

6" Ducting

Tape

4" Ducting

Tape

Screw from

Parts Bag

Insert tab into slot inside Housing

6" to 4" Reducer provided in select models

Page 10

Retrofit Installation

Install Knockout Plate, Connect Wires and Reinstall Wiring Panel

• Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

mounts to inside of

Screw from

Parts Bag

Attach cable

clamps to

Knockout Plate.

Knockout Plate

Housing and may

be oriented

as desired.

Screw set

aside in

Step 6

XB50L1

XB80L1

XB110L1 Installation Guide

Connect wires

LINE

BLK

WHT

GRD

LIGHT

SWITCH

FAN

SWITCH

BLK WHT GRD

DIMMER SWITCH

LIGHT WITH ON/OFF SWITCH

RED BLU

BLK

WHT GRD

BLK

LIGHT

LIGHT WITH DIMMER SWITCH

RED BLU

FAN

SWITCH

BLK

WHT

GRD

BLK

FAN

UNITSWITCH BOX

RED

LIGHT

WHT

FAN

UNITSWITCH BOX

WHT

RED

WHT

Pa g e 11

2 3

Retrofit Installation

Reinsert and Secure Blower Assembly

CAUTION

Power must be disconnected (see page 2, WARNING item 2) before inserting motor plugs into control assembly.

XB50L1

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

XB80L1

XB110L1 Installation Guide

Install Grille

2 3

If ceiling repairs are needed, place Mask in Housing

after Blower Assembly is secured. See New Construction

Installation Step 6. Remove Mask before installing Grille.

Screws from Parts Bag

Page 12

XB50L1

XB80L1

XB110L1 Installation Guide

WARNING Before servicing or cleaning unit,

switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Operation

To Operate Fan

Use an ON/OFF switch to operate this ventilator. It is normal for this ventilation fan to take approximately 5

seconds to start running after it is turned on.

To Operate Lights

The fan and light can be operated independently, using separate switches. The light may be operated with a dimmer switch. See wiring diagrams.

Cleaning and Maintenance

CAUTION

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

DO NOT remove motor plug to stop spinning motor. Power must be disconnected (see WARNING above) before

motor plug is removed or inserted into control assembly.

Troubleshooting

Symptom: The fan does not run.

• Check for an open fuse or circuit breaker in the building’s service panel.

• Check that the two (2) plug-in connections for the Motor and the Control are seated firmly in place.

• Check that the Blower Wheel spins freely.

Symptom: The fan runs erratically.

• Check that the Blower Wheel is firmly attached to the Motor shaft and both spin freely.

Symptom: The fan seems noisy.

• Check that the back draft damper in the fan’s Duct Connector pivots freely. Screws used to attach the duct to the Duct Connector may be preventing the damper from opening.

• Check that the back draft damper in the wall or roof cap pivots freely. These dampers are sometimes mistakenly painted shut or obstructed by bird and insect debris..

To Clean

For quiet and efficient operation, long life and attractive appearance, remove Grille and vacuum interior of unit with a dusting brush attachment.

The Motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace the Control Assembly and Motor.

+ 28 hidden pages