Broan RMIP33, RMIP45 User Manual

MODELS RMIP33 AND RMIP45

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 AND 13.

Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453) NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687) Broan-NuTone Canada Inc., 1140 Tristar Drive, Mississauga, ON L5T 1H9 (1-888-882-7626)

V05861 rev G

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

HB0031

WARNING WARNING

- 2 -

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off

at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done

by qualified personnel in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the

outdoors.

7. Do not use this unit with any solid-state speed

control device other than RMIPWC optional wall mounted control.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or

when cooking flaming foods.

c) Clean ventilating fans frequently. Grease should

not be allowed to accumulate on fan or filter.

d) Use proper pan size. Always use cookware

appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid,

cookie sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN – You may

be burned.

3. DO NOT USE WATER, including wet dishcloths or

towels – This could cause a violent steam explosion.

4. Use an extinguisher ONLY if: A. You own a Class ABC extinguisher and

you know how to operate it.

B. The fire is small and contained in the area

where it started.

C. The fire department has been called. D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

3. Your insert motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the insert serviced.

4. The minimum hood distance above cooktop must not be less than 24”. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities.

5. Two installers are recommended because of the large size and weight of this unit.

6. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside – Do not exhaust air into spaces within walls or ceiling or into attics, crawl space or garage.

7. This product is equipped with a thermostat which may start blower automatically. To reduce the risk of injury and to prevent power from being switched on accidentally, switch power off at service panel and lock or tag service panel.

8. Because of the high exhausting capacity of this unit, you should make sure enough air is entering the house to replace exhausted air by opening a window close to or in the kitchen.

9. To reduce the risk of fire and electrical shock, the Broan Elite models RMIP33 and RMIP45 must be installed only with Broan interior blower models P5 or P8; Broan exterior models 331H, 332H, 335 or 336; Broan in-line blowers models HLB3, HLB6, HLB9, HLB11. Other blowers cannot be substituted. (Blowers sold separately).

10. Use with approved cord-connection kit only.

11. Please read specification label on product for

further information and requirements.

HL0067

- 3 -

RMP Series Backsplash

(Stainless Steel wall

covering with warming

shelves. Optional)

RML3336S, RML3342S, RML4548S, RML4554S or RML4560S Custom Hood Liner (optional)

Model 415

7” Rd adjustable

elbow (optional)

8” Rd adjustable elbow (optional)

Model 412

transition

/4” x 10” to 7”)

Adapter and damper 3

/4’’ x 10’’

(supplied with P5 and P8 blowers)

Adapter and damper 3

/4’’ x 14’’

(supplied with P8 blower)

Model P5

single-blower

(500 cfm)

RMIP33

OR RMIP45

INSERT

- RMIP33 AND RMIP45 INSERT SYSTEM -

INTERIOR BLOWERS

Flow deviator

(supplied with

P5 and P8 blowers)

Model 647

(7” Rd wall cap)

Model 634 or 644

(roof cap)

Model 643

(8” Rd wall cap)

8” Rd standard duct

Model 407

(7” Rd x 24’’

section)

7” Rd metal

flexible duct

(optional)

8” Rd metal flexible duct (optional)

Model 413

transition

/4” x 10” to 8”)

Model 459

transition

/4” x 14” to 8”)

Model P8 dual-blower (900 cfm)

NOTE: The dual blower P8 can be

installed either with 7’’ round or 8’’ round ductwork. For optimal air and quiet sound performance, use 8’’ round ductwork.

Rough-in kit (supplied with P5 and P8 blowers)

RMIPWC

Wall control

(Optional)

RBFIP Series

Baffle Filters

(Optional)

- 4 -

HL0068

RMP Series Backsplash

(Stainless Steel wall

covering with warming

shelves. Optional)

RML3336S, RML3342S, RML4548S, RML4554S or RML4560S Custom Hood Liner (optional)

Model 418

10” Rd

adjustable elbow

(optional)

Model HLB3 (280 cfm)

in-line blower

(includes one 8” to 10”

round transition)

RMIP33

OR RMIP45

INSERT

- RMIP33 AND RMIP45 INSERT SYSTEM -

IN-LINE AND EXTERIOR BLOWERS

Model 331H (600 cfm)

or 332H (900 cfm)

exterior blower

Model 335 (1200 cfm)

or 336 (1500 cfm)

exterior blower

Model 441

(10” Rd wall cap)

Model 437

(High capacity roof cap)

Model 441

(10” Rd wall cap)

Model 421 (10” Rd. vert. in-line damper) Recommended for use with exterior blowers

Model 410 (10” Rd duct

- 2ft. sections)

10” Rd metal

flexible duct

(optional)

332KR in-line and exterior blower rough-in kit - Purchase separately.

RMIPWC

Wall control

(Optional)

RBFIP Series

Baffle filters

(Optional)

Model HLB6 (600 cfm)

in-line blower

(includes two 4½” x 18½”

to 10’’ round transitions)

Model HLB9 (800 cfm)

or HLB11 (1100 cfm)

in-line blower

(includes two 8” x 12” to

10’’ round transitions)

- 5 -

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

Either an interior or exterior blower or in-line blower may be used with this insert. The insert model RMIP33 or RMIP45 must be installed with blower models P5, P8, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately).

Plan where and how the ductwork will be installed. Access to the top of the hood is preferred for connection of ductwork. As an alternative, flexible metal ductwork may be used.

If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 8, 13, 14, 16, 17, 19 and up of this manual.

Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use round ductwork, with a short section (about 4’ expanded) of flexible metal duct (optional) for attachment to the transition. Use screws to attach flexible metal duct to the rigid duct. Use 2” duct tape to seal duct joints.

The minimum hood distance above cooktop must not be less than 24”. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities.

Distances over 30” are at the installer and users discretion.

Insert with interior blower

Roof cap

Wall cap

HH0038A

7” or 8” round ducts with 7” or 8” round metal flex. duct (optional)

3 1/4” x 10” to 7” or 8” transition or 3 1/4” x 14” to 8” transition

24” minimum above cooking surface

MODEL P5 (SINGLE) OR

P8 (DOUBLE) INTERIOR BLOWER

TYPICAL DUCTWORK

MODEL 331H, 332H, 335 OR

336 EXTERIOR BLOWER

TYPICAL DUCTWORK

MODEL HLB3, HLB6, HLB9 OR HLB11

IN-LINE BLOWER

TYPICAL DUCTWORK

Insert with exterior blower

10” round duct

Exterior blower

HH0039A

24” minimum above cooking surface

10” round metal flex. duct (optional)

In-line blower

10” round duct

HH0058A

24” minimum above cooking surface

10” round metal flex. duct (optional)

Roof cap

Wall cap

Insert

2. PREPARE THE INSTALLATION

Make sure that the following items are included:

- Insert

- Accessories:

• Filters (3 for RMIP33 model, 4 for RMIP45 model)

• Bag of parts including: (4) lock nuts, (1) wire clamp, (8) no. 8 x 3/4” standard screws, (2) wire connectors,

(2) no. 6 x 1/2” standard screws, (8) no. 8 x 3/8” screws. Discard items not used.

Parts sold separately:

- Interior blower Model P5 includes blower, rough-in kit, flow deviator and 31/4” x 10” adapter

- Interior blower Model P8 includes blower, rough-in kit, flow deviator and 3

/4” x 10” adapter and 31/4” x 14” adapter

- In-line blower assembly HLB3, HLB6, HLB9 or HLB11 (all include transition)

- In-line blower rough-in plate model 332KR, required for all In-line or Exterior Blowers

- Exterior blower assembly 331H, 332H, 335 or 336

- Halogen lights 120V, 50W, PAR 20 (2 for RMIP33 model and 3 for RMIP45 model)

- Custom hood liner Model RML3336S, RML3342S, RML4548S, RML4554S or RML4560S (optional)

- Backsplash RMP Series (optional)

- RMIPWC Remote control (optional)

- Baffle filters RBFIP Series (optional)

- Transitions, ducts (rigid and flexible), elbows, dampers, wall and roof caps. Refer to page 3 and 4 for a complete list of venting options and model numbers.

NOTE: During installation, protect countertop and/or cooktop.

+ 11 hidden pages