Broan 410, 418, EC62, 437, 441 User Manual

EC62 SERIES

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGE 12.

Broan-NuTone Canada Inc.; Mississauga, Ontario www.broan.ca 877-896-1119

www.broan.ca

SV08970 rev. 05

HB0091

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING WARNING

- 2 -

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off

at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done

by qualified personnel in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the

outdoors.

7. To reduce the risk of fire or electric shock, do not

use this unit with any additional solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

10.

When applicable local regulations comprise more restrictive installation and/or certification requirements, the aforementioned requirements prevail on those of this document and the installer agrees to conform to these at his own expenses.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or

when flambeing food (i.e. Crêpes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not

be allowed to accumulate

on fan, filters or in exhaust

ducts

d) Use proper pan size. Always use cookware appropriate

for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid,

cookie sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN – You may

be burned.

3. DO NOT USE WATER, including wet dishcloths or

towels – This could cause a violent steam explosion.

4. Use an extinguisher ONLY if: A. You own a Class ABC extinguisher and

you know how to operate it.

B. The fire is small and contained in the area

where it started.

C. The fire department has been called. D. You can fight the fire with your back to an exit.

*Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

4. Your power pack motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the power pack serviced.

5. The minimum hood distance above cooktop must not be less than 24”. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities. For a gas range, the bottom of the hood MUST NOT BE LESS than 30” above cooktop.

6. Two installers are recommended because of the large size and weight of this unit.

7. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside – Do not exhaust air into spaces within walls or ceiling or into attics, crawl space or garage.

8. Because of the high exhausting capacity of this unit, you should make sure enough air is entering the house to replace exhausted air by opening a window close to or in the kitchen.

9. To reduce the risk of fire and electrical shock, the Broan Elite EC62 Series models must be installed only with their own built-in blower(s). Other blowers cannot be substituted.

10. Please read specification label on product for further information and requirements.

- 3 -

- EC62 SERIES POWER PACK SYSTEM -

3¼” X 10” ADAPTER/DAMPER

(SUPPLIED WITH SINGLE BLOWER

POWER PACK

)

SINGLE BLOWER

(600 CFM, SUPPLIED

WITH POWER PACK

)

UAL BLOWER

(1000 CFM, SUPPLIED WITH

POWER PACK

)

L6230SS,

L6236SS

OR L6242SS

CUSTOM HOOD LINER

(OPTIONAL)

TANDARD

3¼” X 10” DUCT

(NOT INCLUDED)

EC622301SS

POWER PACK

EC621306SS

POWER PACK

STANDARD

3¼” X 10” ROOF CAP

(NOT INCLUDED)

STANDARD

3¼” X 10” WALL CAP

(NOT INCLUDED)

MODEL 437

HIGH CAPACITY ROOF CAP

(NOT INCLUDED)

MODEL 441

10” ROUND WALL CAP

(NOT INCLUDED)

MODEL 418 10” ROUND ADJUSTABLE ELBOW (NOT INCLUDED)

ODEL 410

10” ROUND DUCT — 2 FT. SECTIONS (NOT INCLUDED)

10” R

OUND VERTICAL

IN-LINE DAMPER (SUPPLIED WITH 1000 CFM

DUAL BLOWER POWER PACK

)

10” R

OUND ADAPTER

(SUPPLIED WITH 1000 CFM

DUAL BLOWER POWER PACK

)

L6230SS,

L6236SS

OR L6242SS

CUSTOM HOOD LINER

(OPTIONAL)

HL0126

- 4 -

1. PREPARE THE INSTALLATION

2. INSTALL DUCTWORK AND ELECTRICAL WIRING

Plan where and how the ductwork will be installed. Access to the top of the power pack is preferred for connection of ductwork. Install proper-sized ductwork, elbows and roof or wall cap for the type of power pack you are installing. If installing EC621306SS

single blower power pack, use 3¼” x 10” ductwork. If installing EC622301SS double blower power pack, use 10” round ductwork. Use 2” metal foil duct tape to seal duct joints.

We recommend to install the power pack at a minimum distance of 24” from an electric range and at 30” from a gas range.

Distances over 30” are at the installer and users discretion. Run 3-wire power supply cable to installation location. Its length should extend at least 4 feet below the bottom of the custom

hood.

Power pack

Roof cap

Wall cap

HH0116A

3¼” x 10” adapter & damper

24” minimum above cooking surface (30” for gas range)

3¼” x 10” duct

MODEL EC621306SS

(SINGLE BLOWER) TYPICAL DUCTWORK

Power pack

Roof cap

Wall cap

HH0117A

10” round duct

10” round adapter

10” round elbow

10” in-line vertical damper

24” minimum above cooking surface (30” for gas range)

MODEL EC622301SS

(DUAL BLOWER) TYPICAL DUCTWORK

NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the

manufacturer.

Make sure that the following items are included

- Power Pack

- Accessories: • 2 Filters

• 2 Filter knobs with screws, taped inside the hood

• 2 Shielded halogen lamps (120 V, 50 W max., MR16 with GU10 base)

• 3¼” x 10” adapter and damper (supplied with 600 CFM single blower power pack)

• 10” round in-line vertical damper (supplied with 1000 CFM dual blower power pack)

• 10” round adapter (supplied with 1000 CFM dual blower power pack)

• Bag of parts including: 1 wire clamp, 2 wire connectors, 4 no. 8 x 3/8” screws, 9 no. 8 x 1/2” chrome plated screws, 10 no. 8-32 x 1/4” screws. If need be, discard extra screws.

Parts sold separately:

- Custom hood liner Model L6230SS, L6236SS or L6242SS (optional)

- Ducts, elbows, wall and roof caps. Refer to page 3 for a complete list of venting options and model numbers. NOTE: During installation, protect countertop and/or cooktop.

NOTE: Although the horizontal discharge installation is feasible with EC621306SS power pack model, this installation

type should be performed in specific situation only since it requires particular knowledge and technical skills from the installers.

WARNING

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

NOTE: The dual blower model has the same dimensions than the single blower model, but does not have a horizontal discharge.

Refer to single blower power pack illustration for back and side views, and discard horizontal discharge measurements.

3. PREPARE CUSTOM HOOD

The custom hood must be constructed to fit the shape and total weight of the EC62 power pack model. The recommended minimum thickness for the custom hood base is 5/8”. If an optional custom hood liner will be installed, we recommend the sides and front of the custom hood to be 3/4” thick. If the optional custom hood liner will not be installed, the custom hood sides and front thickness are at the installer’s discretion. See chart and illustration for details.

POWER PACK

TYPES

TOTAL

WEIGHT

SINGLE BLOWER 33 LB DUAL BLOWER 45 LB

- 5 -

SINGLE BLOWER POWER PACK

DUAL BLOWER POWER PACK

HK0114A

13 5/16”

1¾”

7/8”

5¼”

ø10”

TOP VIEW

WARNING

When building a custom hood, always follow all applicable construction codes and standards. The custom hood must be positively secured to wall studs or other wooden framework behind the drywall. Make sure it is capable of supporting its own weight and the weight of the power pack. Failure to do so may cause personal injury or damage to countertop or cooktop.

7/8”

1¾”

/16”

1¾” 13 5/16”

TOP VIEW

9¾”

5/8”

16”

3 ³/

10 1/8”

10½”

5/8”

3 ³/

16”

/16”

HK0104A

/8”

26 28 1/8”

BACK VIEW SIDE VIEW

11/16”

13¼” 14¾”

+ 9 hidden pages