Broadrack KSR-11508-DVI, KSR-11708HD-DVI, KSR-12008-DV, KSR-11908-DVI, KSR-11708-DVI User Manual
Page 1
KSR Series
Single Rail LCD Console with DVI KVM Switch
User Manual
Rev 1.0
Page 2
KSR Series User Manual
I
Packing List
The complete KSR-11508-DVI / 11708-DVI / 11708HD-DVI / 11908-DVI package
consist of:
One 1U 19” rack mount console
Two rails with front and rear bracket
Two long brackets. (Needed for rack depth 828 ~ 1000mm)
One DVI cable
One USB cable (USB type B to USB type A)
One DC power adapter
One power cord
One user manual CD
One quick installation guide
Two key
Six flat screws (for rail mount to console body)
Six screws (for replace long bracket)
The complete KSR-12008-DVI package consist of:
One 1U 19” rack mount console
Two rails with front and rear bracket
One DVI cable
One USB cable (USB type B to USB type A)
One DC power adapter
One power cord
One user manual CD
One quick installation guide
Two key
Six flat screws. (for rail mount to console body)
Check to make sure that the unit was not damaged in shipping. If you encounter a
problem, contact your dealer.
Please read this manual thoroughly, and follow the installation and operation
procedures carefully to prevent any damage to the product, and/or any of the devices
that connect to it.
Page 3
KSR Series User Manual
II
Safety Instructions
1. Please read these safety instructions carefully.
2. Please keep this User’s Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning. Don’t use
liquid or sprayed detergent for cleaning. Use moisture sheet or clothe for
cleaning.
4. For pluggable equipment, the socked-outlet shall be installed near the
equipment and shall be easily accessible.
5. Please keep this equipment from humidity.
6. Lay this equipment on a reliable surface when install. A drop or fall could cause
injury.
7. Do not leave this equipment in an environment unconditioned, storage
temperature above 600 C, it may damage the equipment.
8. The opening on the enclosure is for air convection hence the equipment from
overheating. DO NOT COVER THE OPENING.
9. Make sure the voltage of the power source connect the equipment to the power
outlet.
10. Please keep the power cord such a way that people can not step on it. Do not
place anything over power cord. The power cord must rate for the voltage and
current marked on the product’s electrical ratings label. The voltage and current
rating of the cord should be greater than the voltage and the current rating
marked on the product.
11. All cautions and warning on the equipment should be noted.
12. If the equipment is not in use for long time, disconnect the equipment from mains
to avoid being damaged by transient over-voltage.
13. Never pour any liquid into ventilation openings; this could cause fire or electrical
shock.
14. Never open the equipment. For safety reason, qualified service personnel
should only open the equipment.
15. If one of the following situations arises, get the equipment checked by service
personnel.
The Power Cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you can not get it work according to
Page 4
KSR Series User Manual
III
User’s Manual.
The equipment has dropped and damaged.
If the equipment has obvious signs or breakage.
Page 5
KSR Series User Manual
IV
Index of Contents
Packing List .......................................................................................................... I
Safety Instructions ............................................................................................... II
Index of Contents .............................................................................................. IV
1. General Information ...................................................................................... 1
1.1 Overview ............................................................................................... 1
1.2 Product Specification ............................................................................ 2
1.2.1 KSR-11508-DVI Specification ..................................................... 2
1.2.2 KSR-11708-DVI Specification ..................................................... 4
1.2.3 KSR-11708HD-DVI Specification ................................................ 6
1.2.4 KSR-11908-DVI Specification ..................................................... 8
1.2.5 KSR-12008-DVI Specification ................................................... 10
2. Panel Controls and OSD Function .............................................................. 12
2.1 Auto Tune ........................................................................................... 12
2.2 Input Source ....................................................................................... 13
2.3 Brightness ........................................................................................... 13
2.4 Contrast .............................................................................................. 14
2.5 Color ................................................................................................... 14
2.6 Position ............................................................................................... 15
2.7 Language ............................................................................................ 16
2.8 Recall .................................................................................................. 17
2.9 Exit ...................................................................................................... 17
2.10 Power Indicator ................................................................................. 17
3. Installation .................................................................................................. 18
3.1 Install KSR-11508-DVI / 11708-DVI / 11908-DVI into Cabinet ............ 18
3.1.1 Notes ........................................................................................ 18
3.1.2 Hardware Kits Contents ............................................................ 18
3.1.3 Installation Steps ....................................................................... 19
3.1.4 Replace Longer Bracket Steps (For rack depth 828~1000mm) 21
3.1.5 Unload Steps ............................................................................ 21
3.2 Install KSR-12008-DVI into Cabinet .................................................... 23
3.2.1 Notes ........................................................................................ 23
3.2.2 Hardware Kits Contents ............................................................ 23
3.2.3 Install Console Steps ................................................................ 24
3.3 Installing the Video Card and Video Driver ......................................... 26
3.3.1 Configuring the Display Settings ............................................. 26
3.3.2 Connecting the Console .......................................................... 27
3.4 Turning on the Console ....................................................................... 28
Page 6
KSR Series User Manual
V
3.5 Testing the Console ............................................................................ 28
4. KVM Switch ................................................................................................ 29
4.1 Introduction ............................................................................................... 29
4.1.1 Features ........................................................................................... 29
4.1.2 Technical Specifications .................................................................. 30
4.1.3 System Requirements ...................................................................... 30
4.1.4 Cable Diagrams ............................................................................... 31
4.1.5 Rear Panel ....................................................................................... 31
4.2 Easy Operation ......................................................................................... 32
Page 7
KSR Series User Manual
1
1. General Information
1.1 Overview
The KVM console is an ideal solution for network administration with multiple
servers / platforms. Their 15 / 17 / 19 / 20.1-inch large size TFT LCD color display
and ultra-low-profile compact industrial keyboard / touchpad provide the
user-friendliest and most reliable environment for network administrators. All these
functions are integrated in a 19-inch 1U space with rugged construction design to
achieve ultra space saving and high reliability for high quality industrial network
applications.
The KVM console provide superior picture quality and state-of-the-art features
mounted in an industrial grade, rack mount console. The console forms a rugged
enclosure that protects the panel from industrial hazards and permits easy
access to panel controls.
The KVM console panels provide flicker-free color images at optimal
resolutions. The panels’ 0.297 x 0.297 mm pixel pitch – 15 inch (0.264 x 0.264 mm
pixel pitch – 17 inch, 0.098 x 0.294 mm pixel pitch – 19 inch, 0.255 x 0.255mm pixel
pitch – 20.1 inch) ensures crisp images with clear definition, even at high resolutions.
The KVM console panels are intelligent, microprocessor-based, and have an
ergonomically designed display.
The KVM console panels employ the latest in active matrix thin film transistor
(TFT) technology, providing crisp screen images and wide viewing angles.
Unlike CRT panels, LCD panels are inherently immune to the magnetic fields
commonly found on the plant floor or communications centers. LCDs are also
typically brighter than conventional CRT technology, making them ideal for the
high ambient lighting conditions found in many of today's factory environments.
On-screen menus allow for display adjustments. In addition, the panels'
Plug-n-Play+ features support Windows 95/98,NT and XP, while a universal
power supply ensures global applicability.
The KVM console panels are compatible with most digital and analog RGB (red,
green, blue) display standards, optional for Sun Micro System, Apple Macintosh
Centris, Quadra, and Macintosh II family signals. The LCD panel is capable of
displaying crisp and vibrant color graphics with VGA, S2GA, XGA (non-interlaced),
SXGA, UXGA, and most Macintosh compatible color video cards.
Page 8
KSR Series User Manual
2
1.2 Product Specification
1.2.1 KSR-11508-DVI Specification
Model Name
KSR-11508-DVI
Number of Ports
8
KVM Switch Type
DVI KVM switch
Dimension
592.0 x 482.0 x 44.0 mm / 23.3 x 19.0 x 1.7 inches
Package Dimension
788 x 564 x 206 mm / 31.0 x 22.2 x 8.1 inches
Net Weight
12.0 Kg / 26.5 lbs
Gross Weight
18.5 Kg / 40.8 lbs
Display Size
15 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1024 x 768 (XGA)
Pixel Pitch
Supports 0.297 mm x 0.297 mm
Viewing Angle (CR>10)
Right-Left View 130°(Typ)
Up-Down View 100°(Typ)
Contrast Ratio
550:1
Brightness
White 250 cd/m² (Center 1 point Typ)
Back Light
Dual Lamps for Back Light
Supported Colors
16M Colors (6-bit with FRC)
Response Time
Rising Time 2 ms, Decay Time 6 ms
Operating System
Dos, Unix, Linux, OSX, Windows ( XP, 7, 8, Server 2012 R2)
Connectors
PC Port Connectors
8 x DVI female
8 x USB type B
8 x 3.5mm audio jack
Console Connectors
1 x DVI female
2 x USB 1.1 type A for keyboard / mouse
USB Hub Ports
2 x USB 2.0 type A device hub port
Power Connector
1 x DC jack
Signal Cables
DVI, USB A-B, audio cable
Keyboard Mouse
106 key PS/2 keyboard with touch pad
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
10.12W for Panel
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Page 9
KSR Series User Manual
3
Keyboard Language
US, UK, German, French, Spanish, Italian, Portuguese, Dutch,
Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese,
Mandarin, Russian, Arabic
Table 1-1. KSR-11508-DVI Specification
Figure 1-1. KSR-11508-DVI Dimension
Page 10
KSR Series User Manual
4
1.2.2 KSR-11708-DVI Specification
Model name
KSR-11708-DVI
Number of ports
8
Dimension
592.0 x 482.0 x 44.0 mm / 23.3 x 19.0 x 1.7 inches
Package Dimension
788 x 564 x 206 mm / 31.0 x 22.2 x 8.1 inches
Net Weight
13.0 Kg / 28.7 lbs
Gross Weight
20.5 Kg / 45.2 lbs
Display Size
17 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1280 x 1024 (SXGA)
Pixel Pitch
Supports 0.264 mm x 0.264 mm
Viewing Angle (CR>10)
Right-Left View 170°(Typ)
Up-Down View 160°(Typ)
Contrast Ratio
1000:1
Brightness
White 250 cd/m² (Center 1 point Typ)
Back Light
Dual Lamps for Back Light
Supported Colors
16.7M Colors (6-bit with FRC)
Response Time
Rising Time 3.8 ms, Decay Time1.2 ms
Operating System
Dos, Unix, Linux, OSX, Windows ( XP, 7, 8, Server 2012 R2)
Connectors
PC Port Connectors
8 x DVI female
8 x USB type B
8 x 3.5mm audio jack
Console Connectors
1 x DVI female
2 x USB 1.1 type A for keyboard / mouse
USB Hub Ports
2 x USB 2.0 type A device hub port
Power Connector
1 x DC jack
Signal Cables
DVI, USB A-B, audio cable
Keyboard Mouse
106 key PS/2 keyboard with touch pad
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
9.91 W for Panel
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Keyboard Language
US, UK, German, French, Spanish, Italian, Portuguese, Dutch,
Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese,
Mandarin, Russian, Arabic
Table 1-2. KSR-11708-DVI Specification
Page 11
KSR Series User Manual
5
Figure 1-2. KSR-11708-DVI Dimension
Page 12
KSR Series User Manual
6
1.2.3 KSR-11708HD-DVI Specification
Model name
KSR-11708HD-DVI
Number of ports
8
Dimension
592.0 x 482.0 x 44.0 mm / 23.3 x 19.0 x 1.7 inches
Package Dimension
788 x 564 x 206 mm / 31.0 x 22.2 x 8.1 inches
Net Weight
13.0 Kg / 28.7 lbs
Gross Weight
20.5 Kg / 45.2 lbs
Display Size
17.3 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1920 x 1080 (Full HD)
Pixel Pitch
Supports 0.198 mm x 0.198 mm
Viewing Angle (CR>10)
Right-Left View 140°(Typ)
Up-Down View 120°(Typ)
Contrast Ratio
650:1
Brightness
White 300 cd/m² (Center 1 point Typ)
Back Light
Dual Lamps for Back Light
Supported Colors
16.7M Colors (8-bit with FRC)
Response Time
Rising Time 2 ms, Decay Time 6 ms
Operating System
Dos, Unix, Linux, OSX, Windows ( XP, 7, 8, Server 2012 R2)
Connectors
PC Port Connectors
8 x DVI female
8 x USB type B
8 x 3.5mm audio jack
Console Connectors
1 x DVI female
2 x USB 1.1 type A for keyboard / mouse
USB Hub Ports
2 x USB 2.0 type A device hub port
Power Connector
1 x DC jack
Signal Cables
DVI, USB A-B, audio cable
Keyboard Mouse
106 key PS/2 keyboard with touch pad
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
10.2 W for Panel
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Keyboard Language
US, UK, German, French, Spanish, Italian, Portuguese, Dutch,
Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese,
Mandarin, Russian, Arabic
Table 1-3. KSR-11708HD-DVI Specification
Page 13
KSR Series User Manual
7
Figure 1-3. KSR-11708HD-DVI Dimension
Page 14
KSR Series User Manual
8
1.2.4 KSR-11908-DVI Specification
Model name
KSR-11908-DVI
Number of ports
8
Dimension
642.0 x 482.0 x 44.0 mm / 25.2 x 19.0 x 1.7 inches
Package Dimension
827 x 564 x 206 mm / 32.6 x 22.2 x 8.1 inches
Net Weight
14.0 Kg / 30.9 lbs
Gross Weight
21.5 Kg / 47.4 lbs
Display Size
19 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1280 x 1024 (SXGA)
Pixel Pitch
Supports 0.098 mm x 0.294 mm
Viewing Angle (CR>10)
Right-Left View 170°(Typ)
Up-Down View 160°(Typ)
Contrast Ratio
1000:1
Brightness
White 250 cd/m² (Center 1 point Typ)
Back Light
Dual Lamps for Back Light
Supported Colors
16.7M Colors (6-bit with FRC)
Response Time
Rising Time 3.6 ms, Decay Time 1.4 ms
Operating System
Dos, Unix, Linux, OSX, Windows ( XP, 7, 8, Server 2012 R2)
Connectors
PC Port Connectors
8 x DVI female
8 x USB type B
8 x 3.5mm audio jack
Console Connectors
1 x DVI female
2 x USB 1.1 type A for keyboard / mouse
USB Hub Ports
2 x USB 2.0 type A device hub port
Power Connector
1 x DC jack
Signal Cables
DVI, USB A-B, audio cable
Keyboard Mouse
106 key PS/2 keyboard with touch pad
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
11.03W for Panel
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Keyboard Language
US, UK, German, French, Spanish, Italian, Portuguese, Dutch,
Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese,
Mandarin, Russian, Arabic
Table 1-4. KSR-11908-DVI Specification
Page 15
KSR Series User Manual
9
Figure 1-4. KSR-11908-DVI Dimension
Page 16
KSR Series User Manual
10
1.2.5 KSR-12008-DVI Specification
Model name
KSR-12008-DVI
Number of ports
8
Dimension
639.6 x 482.0 x 43.8 mm / 25.2 x 19.0 x 1.7 inches
Package Dimension
827 x 564 x 206 mm / 32.6 x 22.2 x 8.1 inches
Net Weight
18.0 Kg / 39.7 lbs
Gross Weight
23.5 Kg / 51.8 lbs
Display Size
20.1 inches
Panel Type
Active Matrix TFT LCD
Resolution Capabilities
Maximum Resolution up to 1600 x 1200 (UXGA)
Pixel Pitch
Supports 0.255 mm x 0.255 mm
Active Display Area
Horizontal: 408.0 mm, Vertical: 306.0 mm
Viewing Angle (CR>10)
Right-Left View 178°(Typ)
Up-Down View 178°(Typ)
Contrast Ratio
1000 : 1
Brightness
White 300 cd/m²
Back Light
Six Lamps for Back Light
Supported Colors
16.7M Colors (8-bit with FRC)
Response Time
Rising Time 7 ms, Decay Time 9 ms
Operating System
Dos, Unix, Linux, OSX, Windows ( XP, 7, 8, Server 2012 R2)
Connectors
PC Port Connectors
8 x DVI female
8 x USB type B
8 x 3.5mm audio jack
Console Connectors
1 x DVI female
2 x USB 1.1 type A for keyboard / mouse
USB Hub Ports
2 x USB 2.0 type A device hub port
Power Connector
1 x DC jack
Signal Cables
DVI, USB A-B, audio cable
Keyboard Mouse
106 key PS/2 keyboard with touch pad
Sync
45 ~ 80 KHz
Power Source
100 ~ 240 VAC input
Power Consumption
35W
Temperature
Operate 0 ~ 50°C / 32 ~ 122°F
Storage -20 ~ 60°C / -4 ~ 140°F
Humidity
10% ~ 90% RH
Chassis Construction
Heavy duty steel materials
Keyboard Language
US, UK, German, French, Spanish, Italian, Portuguese, Dutch,
Swiss, Belgium, Swedish, Hebrew, Norwegian, Danish, Japanese,
Mandarin, Russian, Arabic
Table 1-5. KSR-12008-DVI Specification
Page 17
KSR Series User Manual
11
Figure 1-5. KSR-12008-DVI Dimension
Page 18
KSR Series User Manual
12
2. Panel Controls and OSD Function
Table 2-1. Panel Controls
Figure 2-1. KSR-11508-DVI / 11708-DVI OSD Control Bar
Figure 2-2. KSR-11708HD-DVI / KSR-11908-DVI / 12008-DVI OSD Control Bar
2.1 Auto Tune
Press the “auto tune” button. The panel will adjust the display size
automatically and also tune the panel to its best condition.
Controls
Description
Soft power on/off button. Adjacent LED is lit when
on.
Auto
Auto-synchronize and scale down display to any
valid factory preset timings.
Press to scroll the function you want to adjust.
Press to scroll the function you want to adjust.
Menu
To access the main menu. This button also acts as
the “Enter” button.
Page 19
KSR Series User Manual
13
2.2 Input Source
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3. Press the“menu”button to enter,and you will see:
VGA / DVI
4. Use the “Down” and “Up” button to select the input source of signal.
5. Press the “menu” button to enter
2.3 Brightness
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3. Press the“menu”button to enter.
4. Use the“Down”and“Up”button to adjust the brightness of the display.
5. Press the “menu” button to enter.
Page 20
KSR Series User Manual
14
2.4 Contrast
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
1. Press the “menu” button to enter.
2. Use the “Down” and “Up” button to adjust the contrast of the display.
3. Press the “menu” button to enter.
2.5 Color
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
Page 21
KSR Series User Manual
15
3. Press the “menu” button to enter. And you will see:
Icon
Description
9300°K
To set CIE coordinates at 9300°K color
7500°K
To set CIE coordinates at 7500°K color
6500°K
To set CIE coordinates at 6500°K color
User
To set user defined CIE
Auto color
To auto adjust color
Return
To exit and return to the previous page
Table 2-2. Icon Description
4. Use the “Down” and “Up” button to adjust the color of the display.
5. Press “menu” to enter.
2.6 Position
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3. Press the “menu” button to enter. And you will see:
Icon
Description
Image Pos
To adjust the position of the image.
OSD Pos
To adjust the position of the OSD.
Return
To exit and return to the previous page
Table 2-3. Icon Description
4. Use the “Down” and “Up” button to scroll.
Page 22
KSR Series User Manual
16
5. Press the “menu” button to enter.
2.7 Language
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3. Press the “menu” button to enter. And you will see:
English
German
French
Italian
Spanish
4. Use the “Down” and “Up” button to scroll.
5. Press the “menu” button to enter.
Page 23
KSR Series User Manual
17
2.8 Recall
1. Press the “menu” button.
2. Use the “Down” and “Up” button to scroll.
Auto tune.
Input Source
Brightness
Contrast
Color
Position
Language
Recall
Exit
3. Press the “menu” button to enter, and you will see:
Yes/ No
4. Select “Yes” button then ‘Menu” button to recall the factory setting.
Select “No “ to return to the previous page.
2.9 Exit
Press the “exit” button to quit OSD menu.
2.10 Power Indicator
GREEN ON
RED STANDBY
RED SUSPEND
RED OFF
OSD – On Screen Display
Page 24
KSR Series User Manual
18
3. Installation
3.1 Install KSR-11508-DVI / 11708-DVI / 11908-DVI into Cabinet
3.1.1 Notes
1. Please check all peripherals according the list before installation. To make sure
that the whole unit was not damaged and lost during shipping process. If you
encounter any problem, please contact your dealer.
2. Before installation, make sure all peripherals and computer have been turned
off.
3.
Model name
The cabnet depth range
KSR-11508-DVI / 11708-DVI
614 ~ 1000 mm
KSR-11908-DVI
664 ~1000 mm
Contact your dealer for deeper cabinet application.
4. Reliable grounding of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct
connections to the branch circuit.
3.1.2 Hardware Kits Contents
1. Rail with front and rear bracket x 2. (Please identify the brackets. Right and left
sides are different. 15” and 17” for rack depth 614 ~ 828 mm, 19” for rack
depth 664 ~ 828 mm)
2. Long bracket x 2. (Needed for rack depth 828 ~ 1000mm)
3. Flat screw x 6 (for rail mount to console body)
Page 25
KSR Series User Manual
19
4. Screw x 6
5. Key x 2
3.1.3 Installation Steps
1. Loose (Not release) four rear screws then adjust rear bracket to fit your cabinet.
2. Install front and rear bracket on cabinet.
3. Tight-up four rear screws.
4. Repeat step 1~3 for the other side.
5.
Page 26
KSR Series User Manual
20
5. Push console into left and right rails. (Be careful when take out console.)
6. Unlock and pull rail–lock switch (left and right at the same time) then push
console to the end.
7. Install three screws in rear of the console. (Both sides)
8. Finish installation as below.
rail-lock switch
unlock
lock
Page 27
KSR Series User Manual
21
3.1.4 Replace Longer Bracket Steps (For rack depth 828~1000mm)
1. Release six screws.
2. Take rear bracket out.
3. Input rear long bracket to rear of the rail then adjust rear bracket to fit your
cabinet. Tight-up 2~3 screws upon the length you need. One is forbidden.
4. Repeat step 1~3 for the other side.
5. Repeat 3.1.3 step to install console.
3.1.5 Unload Steps
1. Make sure the console is lock.
2. Release three screws in rear of the console. (Both sides)
Rear long bracket
Original bracket
Page 28
KSR Series User Manual
22
3. Unlock.
4. Pull console out until console lock.
5. Pull rail-release switch and pull console out.(Both sides. Be careful when pull
out console.)
6. Push rail-lock switch on the rail and push rail back.(Both sides)
rail-release switch
rail-lock switch on the rail
Page 29
KSR Series User Manual
23
3.2 Install KSR-12008-DVI into Cabinet
3.2.1 Notes
1. Please check all peripherals according the list before installation. To make sure
that the whole unit was not damaged and lost during shipping process. If you
encounter any problem, please contact your dealer.
2. Before installation, make sure all peripherals and computer have been turned
off.
3. The cabinet depth range must be in 671 ~ 965 mm. Contact your dealer for
deeper cabinet application.
4. Reliable grounding of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to
the branch circuit.
3.2.2 Hardware Kits Contents
1. Rail with front and rear bracket x 2
2. Screw (length = 6 mm) x 6
3. Key x 2
Page 30
KSR Series User Manual
24
3.2.3 Install Console Steps
1. Adjust rail until two screws appear. Loose (Not release) two rear screws then
adjust rear bracket to fit your cabinet.
2. Install front and rear bracket on cabinet.
3. Tight-up two rear screws.
4. Repeat step 1~3 for the other side.
5. Pull rail until it lock and keep the part A in front of the rail (Both sides).Then
push console into left and right rails. (Be careful rear box loose when take out
Rail
Page 31
KSR Series User Manual
25
console from carton.)
6. Pull rail–release switch (left and right at the same time) then push console to
the end.
7. Install three screws in rear of the console (Both sides).
8. Finish installation as below.
Rail-release switch
Part A
Page 32
KSR Series User Manual
26
3.3 Installing the Video Card and Video Driver
Before connecting the LCD console, make sure your computer has a video card already
installed for the panel. After you connect the console, install the video software driver.
The video driver is supplied by the video card manufacturer and may be found on the
CD-ROM that came with your computer. If you need information on installing a video
card or video driver, refer to the manual that came with your video card.
3.3.1 Configuring the Display Settings
After connecting the console and turning on your computer, you may need to
configure one or more of the following display settings:
Display mode (also called desktop area or video resolution)
Refresh rate (also called vertical scan rate or vertical sync)
Color depth (also called color palette or number of colors)
Each video card has several controls that let you adjust the display settings. However,
the software and driver for each video card is unique. In most cases, you adjust these
settings by using a program or utility provided by the manufacturer of the video card.
Most video cards use the Windows Display Properties control panel to configure the
display. To open the Windows Display Properties, click the right mouse button in a
blank area of the Windows desktop and then select Properties. The Settings tab
usually lets you change the Color Palette and the Desktop Area (x by y pixel
resolution).
Some video cards integrate additional features into the Windows Display Properties
control panel to give you an exceptional setup that is flexible and easy to use. For
example, the control panel may include an Advanced Properties button, an
Adjustment tab, or a Refresh tab for changing other settings. Other video cards have
a separate utility for setting display properties.
Whenever you change the resolution, color, or refresh rate, the image size, position,
or shape may change. This behavior is normal. You can readjust the image using the
panel on-screen controls. For more information on the panel on-screen controls, refer
to Chapter 2. For more information on configuring the display settings, refer to the
manual that came with your video card.
Page 33
KSR Series User Manual
27
3.3.2 Connecting the Console
To connect an LCD console to a computer, perform the following steps
Figure 3-1. Connecting Diagram
1. Turn off your computer. You should always turn off your computer before
connecting or disconnecting a device.
2. Connect the USB keyboard, mouse and monitor (for local console use) as well
as other shared USB devices to the LCD console (follow your demand).
3. Connect each of your computers to the LCD console, using the DVI video
cable and USB (type B to type A) cable and audio cable.
Since USB interface is hot-pluggable, you don’t have to turn off the
computer before making connections to the USB port.
If you need to connect a computer with analog video port (HDB15)
to the LCD console, you have to use a HDB15-DVI adapter for
connector conversion.
4. Connect the DC adapter with power cord to the DC jack on the console and then to
a power outlet.
Page 34
KSR Series User Manual
28
3.4 Turning on the Console
Make sure all cables and the power cord are connected properly. Be sure to tighten all
connector screws. Grab the front handle. Pull the console all the way out then lift the
panel up. This will disengage the momentary on / off switch and the unit should
power on. The LED on the left of the panel will be green light.
3.5 Testing the Console
To test that the console is working properly, perform the following steps:
1. Power up the console, and then turn on your computer.
2. Make sure the video image is centered within the screen area. Use the OSD
controls to adjust the image (see note below) or press the Auto button on the left
or underneath of the panel.
If the unit does not power on when the panel is pulled up, try to push
the power on / off button on the left of the LCD panel to power up the
unit.
You can adjust the horizontal and vertical position, contrast, and
brightness to better suit your video card and your personal preference.
Refer to Chapter 2 for more information on using the on-screen menu
to adjust the video display.
Before you begin, make sure that powers to all the devices you will
be connecting up have been turned off. To prevent damage to your
installation due to ground potential difference, make sure that all
the devices on the installation are properly grounded. Consult your
direct vendor for any technical issues if necessary.
Page 35
KSR Series User Manual
29
4. KVM Switch
4.1 Introduction
The DVI USB KVM Switch is an 8-port DVI USB KVM Switch that allows you to
access, control, boot and reboot multiple USB-enabled multimedia computers
using only one USB keyboard, mouse, DVI monitor and a speaker set.
It supports digital video for your maximum convenience in adapting to your
display requirements. It also offers two USB 2.0 device hub ports for high-speed
USB device sharing. Its audio switching function offers you uninterrupted
multimedia experience while performing KVM Switching with multi-platform
support for PC, Macintosh G4 / G5 and iMAC. For users who might need to use
a hotkey preceding sequence other than two scroll locks, we also offer five key
alternatives for free configuration.
4.1.1 Features
8-port DVI USB KVM switch with audio switching and 2 x USB 2.0 hub
ports
TMDS specifications compliant
VESA DDC2B emulation
TMDS signal pass through
HDCP specifications compliant
USB Keyboard and mouse support
USB 2.0 Specification compliant
DVI Single Link technology supports digital video signal transmission
Independent / simultaneous USB hub port, audio channels and PC port
selection
Support for Windows 98 / SE / ME / 2000 / XP / Vista and Linux and Mac
OS
Built-in 2-port USB 2.0 device hub for sharing high-speed USB devices
Multi-platform support for PCs and Macintosh G3 / G4 MACs, iMACs
Channel selection by keyboard hotkey
Resolution support up to 1600 x 1200 (for 20.1” LCD console)
Page 36
KSR Series User Manual
30
4.1.2 Technical Specifications
Feature
Specification
KVM Type
DVI and USB interface KVM switch
PC Ports
8
PC Port Connector
8 x DVI female
8 x USB type B
8 x 3.5mm audio jack
Console Connectors
1 x DVI female
2 x USB 1.1 type A for keyboard / mouse
USB Hub Ports
2 x USB 2.0 type A device hub port
Power Connector
1 x DC jack
PC Selection
Hotkey
Scan Delay Time
5 ~ 100 sec programmable
Table 4-1. Technical Specifications
4.1.3 System Requirements
Model No.
KSR-11508-DVI / 11708-DVI / 11908-DVI /
12008-DVI
Computer side
8 x DVI male to DVI male
8 x USB type B to USB type A cable
8 x audio cable
Table 4-2. System Requirements
Page 37
KSR Series User Manual
31
4.1.4 Cable Diagrams
DVI Cable:
DVI male to one DVI male
Figure 4-1. DVI Cable (1.8M)
USB Cable
USB type B to USB type A cable
Figure 4-2. USB Cable
3.5 mm Audio Cable:
Figure 4-3. Audio Cable
4.1.5 Rear Panel
Figure 4-4. Rear Panel
Local Console DVI Port
Audio Port for Connect Host
USB type B Port for Connect Host
DVI Port for Connect Host
Local Console Keyboard / Mouse Ports (USB type A)
USB Hub Ports (USB type A)
DC Power Jack
Page 38
KSR Series User Manual
32
4.2 Easy Operation
You can use hotkey to control your KVM Switch for PC, USB hub port as well as
audio channel selection.
Keyboard hotkey
A keyboard hotkey sequence consists of at least three specific
keystrokes: See Quick Reference Sheet
Hotkey sequence = + + Command key(s)
* User-definable = SCROLL LOCK, CAPS, ESC, F12 or NUM LOCK
Hotkey preceding sequence configuration: For users who want to use a
preceding sequence other than two consecutive Scroll Locks, there is also one
convenient way to configure it.
(1) Hit ScrollLock + ScrollLock + H, then two beeps will signal readiness for new
preceding sequence selection [or Press and hold down the last front-panel
button (Button 2 or Button 4) until you hear two beeps, then release the button.]
(2) Select and press the key you would like to use as your preceding sequence
(SCROLL LOCK, CAPS, ESC, F12 or NUM LOCK keys are available for
selection) and you’ll hear a beep for selection confirmation. Now you can use the
new preceding sequence to execute your hotkey commands.
Each keystroke within a hotkey sequence should be pressed within
2 seconds. Otherwise, the hotkey sequence will not be validated.
For detailed Hotkey sequences and their corresponding functional
commands, please refer to the quick reference sheet.
Scroll
Lock
Scroll
Lock
Page 39
KSR Series User Manual
33
Quick Reference Sheet
Command
Hotkeys1
Description
Select PC
Channel 2
(Joint-select PC
port / hub port
control / audio, if
binding is
enabled)
ScrLk + ScrLk
+(x)
(x is a top-row
number key)
x = 1~ 8 for PC
channel no.
Select the active PC
channel (Joint-select
PC port / hub port
control / audio, if binding
is enabled)
Select Hub Port
Control 2
(Joint-select
PC & Hub port
control, if binding
is enabled)
ScrLk + ScrLk +
(Fx)
Fx = F1~ F8 (Fx
is a function key)
x = 8 for PC
channel no.
Select the PC channel that
control all USB hub ports
(Joint-select PC & Hub port
control, if PC / hub port
control binding is enabled)
Select Audio
Channel
3
(Joint-select PC
port & audio, if
binding is
enabled)
ScrLk + ScrLk +
A + (y)
(y is a top-row
number key)
y = 1~8 for audio
channel no.
Select the active Audio
channel (Joint-select PC &
audio channel, if binding is
enabled)
Bind PC & Hub
Port Control
Switching
2
(Default)
ScrLk + ScrLk +
Z
Enable the binding of
PC port and hub port
control switching. (Once
this feature is enabled,
any pc and / or hub port
control switching is
bound together) (factory
default)
Unbind PC & Hub Port
Control Switching 2
ScrLk + ScrLk + X
Disable the binding of PC
port and hub port control
switching
Bind PC & Audio
Switching
3
(Default)
ScrLk + ScrLk + Q
Enable the binding of PC
port and audio switching.
(Once this feature is
Page 40
KSR Series User Manual
34
enabled, any pc and / or
audio switching is bound
together) (factory default)
Unbind PC & Audio
Switching 3
ScrLk + ScrLk + W
Disable the binding of PC
port and audio switching
Next lower PC channel 2
(Joint-select PC / hub
port control / audio, if
binding is enabled)
ScrLk + ScrLk + ↑
(arrow up)
Select the next lower
connected PC channel
(Joint-select PC / hub port
control / audio, if binding is
enabled)
Next higher PC channel
2
(Joint-select PC / hub
port control / audio, if
binding is enabled)
ScrLk + ScrLk + ↓
(arrow down)
Select the next higher
connected PC channel
(Joint-select PC / hub port
control / audio, if binding is
enabled)
Previous PC channel
ScrLk + ScrLk +
(Backspace)
Toggle between the
previous channel and
current channel
Beep Sound On / Off
ScrLk + ScrLk + B
Toggle on / off the beep
sound while auto scanning
Define Hotkey
Preceding Sequence
ScrLk + ScrLk + H +
(y)
y = SCROLL LOCK,
CAPS, ESC, F12 or
NUM LOCK
Select the hotkey preceding
sequence among 5
alternative keys
Autoscan
ScrLk + ScrLk + S
Autoscan through every
connected channel for quick
screen browsing of each
channel (scan delay = 5
sec.).
Autoscan with
Programmable Delay
Time
ScrLk + ScrLk + S +
(z)
z = 0~9. 1 10”; 2
20” ; 3 30” ; 4
40” ; 5 50” ; 6
60” ; 7 70” ; 8
Autoscan with a
user-defined delay time
within a range of
10 ~ 100 seconds
Page 41
KSR Series User Manual
35
80” ; 9 90” ; 0
100”
Stop Autoscan
Press any key on
keyboard
Terminate Autoscan activity
Table 4-3. Quick Reference Sheet
1. The USB keyboard hotkeys allows you a faster and broader
control for your KVM switching operation in addition to the
front-panel buttons. If you have configured a hotkey preceding
sequence other than two consecutive scroll locks, you should
change your hotkey sequence accordingly. (For preceding
sequence key configuration, please refer to Quick Installation
Guide)
2. When the binding of PC & USB hub port control switching is
enabled by the hotkey sequence: ScrLk + ScrLk + Z, any PC and
hub port control switching are bound together. To remove this
binding, use the hotkey sequence: ScrLk + ScrLk + X.
3. When the binding of PC & Audio switching is enabled by the
hotkey sequence: ScrLk + ScrLk + Q, any PC and audio switching
are bound together. To remove this binding, use the hotkey
sequence: ScrLk + ScrLk + W.
Mac User: Standard PC Keyboard mapping to MAC
Keyboard -- ScrLk + ScrLk + C = (CD / DVD drive eject key);
ScrLk + ScrLk + F10 = F13 ; ScrLk + ScrLk + F11 = F14 ; ScrLk +
ScrLk + F12 = F15
Loading...