Broadata Communications LBC-SPH4-1HB3-EIR User Manual

LBC-SPH4-1HB3-EIR

LINK BRIDGETM HDBASET

3X TRANSMISSION SYSTEM

BCI reserves the right to make changes to the products described herein without prior

notice or consent. No liability is assumed as a result of their use or application. All

©2013 Broadata Communications, Inc.

rights reserved.

LBC-SPH4-1HB3-EIR User’s Manual

Link Bridge

TM

HDBaseT 3x T ransmission System

SAFETY INSTRUCTIONS AND

COMPLIANCE DECLARA TIONS

PLEASE OBSERVE THE FOLLOWING SAFETY

PRECAUTIONS

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order
to protect and extend the life of your equipment.

Broadata Technical Support, [e-mail]

3

LBC-SPH4-1HB3-EIR User’s Manual
Link Bridge

TM

HDBaseT 3x T ransmission System

TABLE OF CONTENTS

1.0 PRODUCT DESCRIPTION ..............................................5

2.0 OPERATION CONTROLS AND FUNCTIONS .................7

2.1 FRONT PANEL .................................................................7

2.2 REAR P ANEL ...................................................................8

3.0 CONNECTOR PIN ASSIGNMENT.................................10

4.0 MAINTENANCE AND TROUBLESHOOTING ...............11

4.1 MAINTENANCE .............................................................. 11

4.2 TROUBLESHOOTING ...................................................11

5.0 SPECIFICA TIONS...........................................................13

6.0 SERVICE PROCEDURE ................................................14

6.1 REPLACEMENT POLICY ..............................................14

6.2 RETURN AND REPAIR SERVICE .................................14

7.0 LIMITED WARRANTY ....................................................15

8.0 APPENDIX A ...................................................................16

4

Broadata Technical Support, [phone]

LBC-SPH4-1HB3-EIR User’s Manual

Link Bridge

TM

HDBaseT 3x T ransmission System

1.0 PRODUCT DESCRIPTION

The LBC-SPH4-1HB3-EIR HDMI over HDMI and CA T 5e/6 S plitter can
split and distribute a single HDMI input, 2-way IR control and LAN
serving up to three CA T 5e/6 outputs and includes a simultaneous HDMI
bypass output. It supports resolutions up to 1080p Full HD, 4Kx2K
timing, 3D and multi-channel digital audio formats (such LBPCM 7.1Ch,
Dolby TrueHD, Dolby Digital Plus and DTS-HD). The HDMI bypass
output can be connected to an HDMI display or cascaded to another
splitter. The three CA T 5e/6 outputs can be connected to the CA T 5e/6
to HDMI receivers to extend the operating distance up to 100 meters.

Additionally the LAN connectivity will allow a 100BaseT network to be
served to smart TVs or game consoles. The PoH (Power over HDBaseT)
function can power compatible receivers, providing greater flexibility in
installations.

Features

• HDMI with 4K×2K resolution and 3D support, HDCP and DVI
compliant

• Simultaneous HDMI and CA T5e/6/7 outputs

• Supports data rate from 300 Mbps up to 3 Gbps

• Supports a wide range of PC resolutions from VGA to WUXGA
(RB) and HDTV resolutions up to 4K×2K (3840×2160@30 Hz
and 4096×2160@24 Hz)

• Supports transmission of High Definition audio: LPCM 7.1CH,
Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio
(32 kHz~192 kHz sample rate)

• Supports distances up to 100 meters over CAT5e/6/7 cables

• Supports Ethernet network rates up to 100Mbps

• Supports selection of Standard or TV EDID settings

• Supports PoH with compatible receiver units

• Supports control of devices via 2-way IR

• 3D signal display is dependent on the TV/Display’s EDID settings

Broadata Technical Support, [e-mail]

5

LBC-SPH4-1HB3-EIR User’s Manual
Link Bridge

TM

HDBaseT 3x T ransmission System

Note: 1. This system was tested with CAT6/23AWG cables, results

may vary with cables of a different specification.

2. The PoH function is designed for powering compatible Receiver
units only , non-PoH Receivers will need their own power supply .
Receivers of another brand may not be compatible.

3. For playback of 4K×2K HDMI source signals, a 4K×2K capable
display and High Speed HDMI cables are required.

Package Contents

• 1×4 HDMI over HDMI and CA T5e/6/7 Splitter

• 1×IR Receiver

• 1×IR Blaster

• 24V DC Power Adaptor

• Power Cord

• Operation Manual

6

Broadata Technical Support, [phone]

LBC-SPH4-1HB3-EIR User’s Manual

Link Bridge

TM

HDBaseT 3x T ransmission System

2.0 OPERA TION CONTROLS AND FUNCTIONS

2.1 Front Panel

1. HDMI IN:
Connect to HDMI equipped source equipment such as a DVD/

Blu-ray player or game console.

2. SYNC LED:
This LED will illuminate when the HDMI input is connected to a
HDMI source and receiving a signal.

3. HDMI OUT:
Connect to a HDMI display for local monitoring of the HDMI

signal or cascade to another Splitter.

4. HDMI LINK LED:
This LED will illuminate when HDMI output is connected to TV

or display monitor and receiving a signal.

5. EDID STD/TV:
The default setting is TV , when in this mode, the unit will detect

the EDID settings of the display device connected to the CAT
5e/6/7 Output 1. If it detects a 4K×2K capable EDID setting it
will transmit the signal in that format to the output port. If no
4K×2K capable EDID is detected then the unit will detect the
EDID settings and send out the signal that all outputs can accept.

This device has a last memory function and will retain the EDID

settings of the last device connected via the CA T5e/6/7 output
port when it is not connected to a display after power cycling.
Switch to the STD setting to use the unit’s built-in EDID if there
are display problems. In this mode, the video output will be set
to 1080p@60Hz and the audio at LPCM 2CH Stereo..

Broadata Technical Support, [e-mail]

7