BRK electronic FE10GR User Manual

User’s Manual

ry Chemical

ire Extinguisher

own

ith plastic

bracket

8-0137-004

IMPORTANT! Please read carefully and save.

This user’s manual contains important information about your fire e

xtinguisher’s operation. If you are installing this fire extinguisher for use b end user.

Read e installing or using the unit. Make sure everyone in your household is com

pletely familiar with the operation of the extinguisher, and review the instructions regularly. In an emergency, you will not have time to read instructions.

hank you for choosing First Aler t

ou have purchased a high quality fire extinguisher designed to

protect you and your family in case of a fire danger.

M 03/0

y others, you must leave this manual—or a copy of it—with the

xtinguisher label and the entire user’s manual carefully before

or your fire extinguisher needs.

IMPORTANT INFORMATION ABOUT FIRE EXTINGUISHERS

NOTE: Be sure the extinguisher is rated to fight the type of fire most likely to occur in the area you choose to install it. Since household fires commonly start in the kitchen, you should always install an extinguisher in the kitchen. For added security, you should also install additional extinguishers in utility areas, and other living areas in your household.

Fire extinguishers are classified by fire type.The A, B and C rating system defines the kinds of burning materials each fire extinguisher is designed to fight. The numbers in front of the A, B, or C indicate the rating for size of the fire the unit can extinguish. Using the wrong type of fire extinguisher can do more harm than good. Make sure you understand which fire extinguisher to use on each class of fire!

FE5GR is rated Class 5-B:C. FE10GR FE1A10GR

Class A rating:

fighting small fires involving wood, paper, cloth, rubber, and some plastics.

Class B rating: The agent/powder is suitable for

hting small fires involving grease, oil, gasoline,

fig kerosene, and other flammable liquids.

Class C rating: The agent/powder is suitable for fighting small fires in "live" electrical equipment.

is rated Class 10-B:C.

is rated Class 1-A:10-B:C.

The agent/powder is suitable for

READ BEFORE INSTALLING OR USING

INGUISHER!

IRE E

S F

• This extinguisher is designed for use against small fires

•

• Never locate this extinguisher close to an engine, stove or

•

ve just started and are small enough to fight safely.

t ha

tha It is not designed to fight large fires that are burning out of control. If the fire is too hot or smoky for you to get within 6 feet (2 meters) of it, do not try to fight it yourself. Warn

one, evacuate the premises, and have someone call the

e F

ire Department from outside the building.Trying to fight a

large fire yourself can result in injury or death.

t puncture or burn any fire extinguisher. The contents

o n

D are under pressure

our

ther s

o e

xplode if exposed to temperatures over 150° F (66° C).

his extinguisher contains a dry powder extinguishing agent.

T The agent/powder is nontoxic, but can irritate skin. When using

this unit

ter us

, and the extinguisher could explode.

f heat. It is pressurized and could rupture or

ce o

void breathing the powder. Always ventilate the area

1 2 3 4

own

ith metal

bracket

Models FE5GR,

E10GR, FE1A10GR

RE TO INSTALL THIS EXTINGUISHER

WHE

Fire Extinguisher Should Be Mounted:

•

In the vicinity of (but not on or in) a potential source of heat and/or fi

re, like an oven or stove.

•

Where it is easy to reach, near an exit or an escape route from the room.

•

In a location that is convenient, in plain sight, and 3-1/2 to 5 f

eet (1 to 1.5 meters) above the floor.

•

Store the extinguisher high enough to keep it out of the reach of small children.

• On a clean, dry surface where the temperature does not go ab

ove 120° F (49° C) or below –40° F (–40° C).

HOW TO INSTALL THIS EXTINGUISHER

•

Do not mount the extinguisher on drywall or plaster without adeq

uate support. Use strong screws or bolts to mount the bracket securely into solid wood or metal that can support it

, like a wooden partition stud. Secure mounting is needed

o you can remove the extinguisher quickly and easily in an emergency. Also, if the extinguisher is not held securely, it could dr

op to the floor and injure people or damage the

xtinguisher.

•

DO NOT BREAK THE SAFETY SEAL! This seal prevents a

ccidental discharge of the fire extinguisher. Break the seal only in an emergency before using the fire extinguisher.

INSTALL THE MOUNTING BRACKET ON A WALL

. The extinguisher has a bracket for

all mounting.

2. Install the mounting bracket on a wooden stud or other solid surface t

hat will support the weight of the

xtinguisher using the screws or

lts you purchased.

NOTE: Since wall surface types vary, mounting screws are not

included.

bolts specifically designed for the surface on which you will mount the fire extinguisher. The fire extinguisher label lists its maximum weight. Mounting screw head type should be #8 pan on round head screws with #8 flat washers.

3. After installing the mounting bracket, replace the extinguisher on the bracket with the label facing outward, so the label can be easily read.Wrap the bracket strap around the cylinder and snap the buckle closed.

Purchase screws or

INSTALLING THE MOUNTING BRACKET IN A MARINE CRAFT

According to the NFPA Standard 302 (Fire protection Standard for Pleasure and Commercial Motor Craft):

• On marine craft, portable fire extinguishers shall be located to be

readily accessible. Extinguishers shall be secured with a marine bracket to permit immediate release.

• On marine craft, extinguisher agent cylinders shall be mounted a

minimum of 2 inches (5 cm) above moist or wet surfaces to reduce

nger of corrosion.

he d

CHECKING AND INSPECTING THE FIRE EXTINGUISHER

DO NOT CHECK THE PRESSURE OR TEST THE FIRE

• EXTINGUISHER BY SQUEEZING THE LEVER, EVEN BRIEFLY. ONCE USED, IT WILL GRADUALLY LOSE PRESSURE AND WILL NOT BE FULLY CHARGED FOR USE IN AN EMERGENCY.

• When the pointer drops into the red area, the extinguisher

1. Inspect the extinguisher once a week. Remove the extinguisher

2. Check for signs of damage or misuse. Make sure you can still

For more information about fire extinguishers, consult the NFPA

S Fire Protection Association, Inc., Batterymarch Park, Quincy, MA 02169,

SA.

l be pressuriz

y s

from the mounting bracket and inspect the gauge. If the yellow po ized and ready to use.

the extinguisher has lost some pressure and should be repl

ead all the text on the label. Carefully examine the surface of

r the extinguisher for corrosion. You can help prevent corrosion

y clea

b corrosion during the warranty period, return the unit to First Alert (see "Limited Warranty" at the end of this manual).

M nozzle is clean and unobstructed.

W securely into the mounting bracket.

ndard #10, "Portable Fire Extinguishers," available from the National

he GREEN area, the extinguisher is properly pressur-

n t

r is i

ced

ning the extinguisher if it gets wet or dirty. If you notice

amper indicator ("safety seal") is still intact and the

he t

e t

e sur

nish inspecting the extinguisher, always put it back

ou fi

n y

but must be recharged.

If the pointer drops into the RED area,

W TO OPERATE YOUR FIRE

HO EXTINGUISHER IN A FIRE EMERGENCY

•

Make sure your extinguisher may be safely and effectively used on the small fire you want to fight. Always use extreme cauti

on when fighting any fire. Fight a fire only where there is a clear escape p gets worse.

• Avoid breathing smoke and heated fumes; stay low if necessary. Burning materials will release toxic fumes. I

nhaling these fumes may cause injury or death.

•

Always stand back far enough away from the fire—near an exit—and make sure nothing is between you and your escape route. If you get too close to a fire, you risk getting burned or hit b too hot or smoky for you to get within 6 feet (2 meters), DO NOT try to fight the fire yourself. Evacuate immediately and ca

ll the Fire Department.

•

For fires on a kitchen stove, turn oven or burners off i

mmediately if possible. If you can’t reach the oven or burner

controls safely, extinguish the fire first, then turn them off.

•

Fight the fire from an upwind direction with your back to any strong air current. Trying to fight a fire with currents blowing t

owards you can result in serious injury.

ath to allow you to get out safely if the fire

y splattering material like grease. If the fire is

W TO CLEAN AFTER USING A FIRE

HO EXTINGUISHER

OTE:The powder spray from the extinguisher may spread over a

ide area, and may soil upholstery, carpets and walls.

•

Sweep/vacuum up as much of the powder as possible.Then use a d

amp cloth to wipe off the remaining agent.

• If you have any questions about cleaning appliances that the agent has come into contact with, please contact the appliance ma

nufacturer.

IF YOUR EXTINGUISHER NEEDS SERVICE

his fire extinguisher is rechargeable by a certified fire equipment

dealer, regardless of how much of the content was used. O

nce a year, a certified fire equipment dealer, in accordance with the

rvice manual identified on the fire extinguisher label, should service the fire extinguisher. Please refer to your local telephone directory for a ce

rtified dealer.

o not try to service or repair this fire extinguisher under any

rcumstances. Do not try to remove the nozzle or valve assembly. This is a pressurized device that can cause serious injury if tampered w

f there is a problem and it is still under warranty, please see “How to

Obtain Warranty Service” in the Limited Warranty.

ith.

DISPOSING OF A USED EXTINGUISHER

TO FIGHT THE FIRE

Break the

Safety Seal

Remove Extinguisher

from Bracket

1. Remove the extinguisher from the mounting bracket.

2. Hold the unit firmly with the nozzle facing away from you. Pull out the pin to break the “Safety Seal”.You won’t be able to squeeze the lever until the safety seal is removed.

3. Stand back 6 feet (2 meters) from the fire and make sure the fire is not between you and your exit.

4. Hold the extinguisher upright and aim the nozzle at the base of the fire.

5. Squeeze and hold the lever to discharge the powder. Sweep the spray at the base of the burning material, using quick

6. side-to-side motions. (If the spray scatters the fire, move back.)

7. Move slowly towards the fire as the extinguisher spray pushes the

ack. Maintain a 6-foot (2 meter) distance between you and

e b

fir

ont of the fire at all times.

he f

8. Completely discharge the contents of the extinguisher and make sur

9. For kitchen fires on a kitchen stove, turn off the stove immediately if possible, otherwise as soon as it is safe.

10. If you suspect a fire had an electrical origin, shut off the electrical power, if possible, without eliminating your escape route. Do not touch electrical wires or appliances.

11. After you have completely discharged your extinguisher, leave the building and close all the doors behind you.

e is com

he fir

e t

tely out. Flashbacks are common with fires.

queeze and Hold

Lever To Discharge

Powder. Sweep

ide to Side.

AFTER THE FIRE IS EXTINGUISHED

Do not turn the electrical power back on or plug in any appliances

l the area has been cleaned up comple

un to remove the powder from electrical equipment after a fire. If the powder gets wet, it can conduct electricity. (Using a dry chemical

xtinguisher on wet electrical equipment may be hazardous for this

e reason.) This may worsen an electrical leakage problem, impair the

pment’s insulation, or create an electrical shock hazard.

eq If the fire was on a kitchen stove:

• Make sure the oven and all burners are turned off.

• Clean up the powder completely before using the stove or oven. Se area thoroughly.

ou thi

If y

• electrical wires or appliances.

• Leave the building and close all doors behind you. Call the Fire Department and have them inspect the premises. As soon as they sa

• Have a licensed electrician inspect your electrical system. Do not turn the power back on or plug in any electrical equipment until

he i

o Clean After Using a Fire Extinguisher”. Ventilate the

w t

“

re had an electrical origin:

k the fi

he electrical power, if possible--do not touch any

f t

ut o

y it’s safe to return, ventilate the area thoroughly.

ction has been completed.

nspe

It is very important

tely

If you choose not to have a used extinguisher refilled or a non-working u

nit repaired, take it outdoors, turn it upside down, and discharge it completely. Dispose of the empty unit properly, and replace it with a new fire extinguisher.

Never puncture, burn or expose this fire extinguisher to temperatures o

ver 150° F (66° C) even if it is fully discharged. The contents

are under pressure and it could explode.

LIMITED WARRANTY

BRK Brands, Inc. ("BRK") the maker of First Alert®brand products, w

arrants that for a period of ten years from the date of purchase, this product will be free from defects in material and workmanship. BRK, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replace

ment will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a simi exclusive warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. BRK dealers, service centers, or retail stores selling BRK products do not have the right to alter, modify or any way change the terms and conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center. Further, the warranty does not cover acts of God, such as fire, flood, hurricanes and tornadoes.

BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Some states, provinces, or jurisdictions do not allow the exclusion or limitation of incidental or

conse lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have

r rights that vary from state to state, or province to province.

o Obtain Warranty Service:

w t

vice:

retailer. In order to obtain warranty service, contact the Consumer Affairs Division at 1-800-323-9005, 7:30 AM to 5:00 PM, Central Standard Time, Monday through Friday. To assist in serving you, please have the model number and date of purchase available when calling.

Address: 25 Spur Drive, El Paso,TX 79906

Marine Type, U.S.C.G.Type B:C, Size I U.S.C.G. Approval Number 162.028/EX3622 Valid only with Bracket Number P87-0340 or Bracket Number B70-0161 and Strap Number S70-0007. Bracket included.

First Alert®is a registered trademark of the First Alert Trust.

lar product of equal or greater value. This is your

mages or limitations on how long an implied warranty

l d

rvice is required, do not return the product to your

f se

8-0

137-004

M 03/0