BRK electronic CO600B User Manual

USER’S MANUAL

GARAGE



SUGGESTED AREAS FOR INSTALLING ADDITIONAL CO ALARMS

BEDROOM

HALL

LIVING ROOM

KITCHEN

ASEMENT

BEDROOM

EQUIRED TO MEET NFPA RECOMMENDATIONS

120V PLUG-IN CARBON MONOXIDE ALARM

120V AC 60 Hz, 0.09A

Printed in Mexico M08-0152-002 S 07/07

This user’s manual contains important information about your Carbon Monoxide (CO) Alarm’s operation. If you are installing this CO Alarm for use by others, you must leave this manual—or a copy of it—with the end user.

WITH SILENCE FEA

PLEASE READ CAREFULLY AND SAVE.

IMPORTANT!

TURE

Model

CO600

CONFORMS

TO UL 2034

TABLE OF CONTENTS

oduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Intr

Basic Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

How Your CO Alarm Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Understanding Your CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Where to Install CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Where CO Alarms Should NOT Be Installed . . . . . . . . . . . . . . . .2

How to Install Your CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . .3

our CO Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

If Y

If the Alarm Signal Sounds

Using the Silence Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Testing and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Weekly Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Regular Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

What You Need To Know About CO . . . . . . . . . . . . . . . . . . . . . . . . . .4

What is CO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Symptoms of CO Poisoning . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Finding the Source of CO After an Alarm . . . . . . . . . . . . . . . . . .4

Potential Sources Of CO In The Home . . . . . . . . . . . . . . . . . . . .4

How Can I Protect My Family? . . . . . . . . . . . . . . . . . . . . . . . . . .4

y Information for CO Alarms . . . . . . . . . . . . . . . . . . . . . .5-6

Regulator

General Limitations Of CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

INTRODUCTION

BASIC SAFETY INFORMA

• Dangers, Warnings, and Cautions alert you to important operating instructions or to potentially hazardous situations. Pay special attention to these items.

• THIS IS NOT A SMOKE ALARM! This CO Alarm is designed to detect carbon monoxide from ANY source of combustion. It is NOT designed to detect smoke, fir

This CO Alarm is approved for use in single-family residences.

•

This CO Alarm will only indicate the presence of carbon monoxide gas at the sensor pr

esent in other areas.

The Silence Feature is for your convenience only and will not

• correct a CO problem. Always check your home for a potential

oblem after any alar

pr death.

• This CO Alarm should receive continuous 120VAC, 60 Hz, pure sine wave electrical power. Do not use in an extension cord or outlet contr

• NEVER ignore your Carbon Monoxide Alarm if it alarms. Refer to “If Your CO Alarm Sounds” for more information. Failure to do so can r

Test the CO Alarm once a week. If the CO Alarm ever fails to

• test cor not working pr

This pr

• family living units. It is not designed to measure CO levels in compliance with Occupational Safety and Health Administration (OSHA) commer medical conditions that may make them more sensitive to carbon monoxide may consider using warning devices which pr centrations under 30 ppm. For additional information on carbon monoxide and your medical condition contact your physician.

olled by a dimmer or switch.

esult in injury or death.

, have it r

ectly

operly

oduct is intended for use in ordinary indoor locations of

cial or industrial standards. Individuals with

ovide audible and visual signals for carbon monoxide con-

HOW YOUR CO ALARM WORKS

GENERAL INFORMA

Leave your CO Alarm plugged in year-round. CO problems can occur any time during the year it is plugged in and receiving power.

When fully powered, the unit samples the air and takes a new reading about every second. A microchip inside the unit stores each reading, and remembers the levels of CO it has been exposed to over time. The Alarm sounds when it has been exposed to a “critical” level of CO (measured in parts per million or “ppm”) within a specified time (measured in minutes). This CO Alarm features a permanently installed sensor, an indicator light, and an 85 dB alarm horn. It also has a Silence Feature to temporarily quiet the alarm horn.

MALFUNCTION WARNING

This unit performs daily self-diagnostic tests. If the Alarm malfunctions, it should be r

eplaced immediately

THE COVER OF YOUR CO ALARM

1 Test/Silence Button 2 POWER/ALARM Light (Red) 3 (Behind Cover) Alarm Horn: 85 dB audible alarm

for test, alarm, and unit malfunction war

TION

e, or any other gas.

. Carbon monoxide gas may be

e to do so can r

m. Failur

eplaced immediately! If the CO Alar

, it cannot aler

t you to a pr

TION

, and this Alarm can only alert you if

ning

1 2 3 4 5

esult in injur

oblem.

y or

m is

UNDERSTANDING YOUR CO ALARM

WHAT YOU SEE AND HEAR DURING INSTALLATION

WHEN YOU FIRST PLUG-IN THE CO ALARM:

UNDER NORMAL CONDITIONS (AC POWER):

WHEN YOU TEST THE CO ALARM:

WHAT YOU SEE AND HEAR UNDER DIFFERENT CONDITIONS:

WHEN THE ELECTRICITY COMES BACK ON AFTER A POWER FAILURE:

IF THE CO ALARM IS NOT OPERATING PROPERLY (MALFUNCTION SIGNAL):

WHAT YOU SEE AND HEAR IF CO IS DETECTED:

ALARM LEVELS OF CO ARE DETECTED:

IF YOU SILENCE THE ALARM:

IF THE CO LEVELS RETURN TO NORMAL:

Silent

HORN: POWER/ALARM LIGHT: Shines continuously

Silent

HORN: POWER/ALARM LIGHT: Shines continuously

HORN:

Sounds loudly - 4 beeps, pause, 4 beeps, pause

POWER/ALARM LIGHT: Flashes rapidly

Silent

HORN: POWER/ALARM LIGHT: Shines continuously.

Three rapid chirps every minute

HORN: POWER/ALARM LIGHT: Flashes three times in sync with the horn.

Sounds loudly - 4 beeps, pause, 4 beeps, pause.

HORN:

This sequence repeats for as long as the unit is in alarm. POWER/ALARM LIGHT: Flashes rapidly

Silent for about 4 minutes

HORN: POWER/ALARM LIGHT: Flashes rapidly

Note: After 4 minutes, if CO levels dr will remain silent and return to normal operation. If CO presence still indicates a potentially dangerous situation, the horn will sound again.

HORN:

Silent

POWER/ALARM LIGHT: Shines continuously

op below alarm levels, the unit

INSTALLATION

WHERE TO INSTALL CO ALARMS

The National Fire Protection Association (NFPA) recommends that a CO Alarm should be centrally located outside of each separate sleeping area in the immediate vicinity of the bedrooms. For added protection, install additional CO Alarms in each separate bedroom, and on every level of your home.

If your bedroom hallway is longer than 40 feet (12 meters), install a CO Alarm at BOTH ends of the hallway.

In a Single-level Home:

•

Install at least one CO Alarm near or within each separate sleeping ar

ea.

• For added protection, install an additional CO Alarm at least 20 feet (6 meters) away from the furnace or fuel burning heat source.

In a Multi-level Home:

Install at least one CO Alarm near or within each separate sleeping

• area.

• For added protection, install at least one CO Alarm on each level of the home.

• For added protection, install an additional CO Alarm at least 20 feet (6 meters) away from the furnace or fuel burning heat source.

This unit should receive continuous electrical power. Choose an outlet where it cannot be accidentally unplugged or switched off by

en. Keep small childr

childr play with it or unplug it. Explain what the alarms mean.

WHERE CO ALARMS SHOULD NOT BE

ALLED

INST

DO NOT LOCA

• In garages, kitchens, furnace rooms, or in any extremely dusty,

• Closer than 15 feet (4.6 meters) from a furnace or other fuel

• Within 5 feet (1.5 meters) of any cooking appliance.

•

• In turbulent air, like near ceiling fans, heat vents, air conditioners,

•

• In outlets covered by curtains or other obstruction.

• This CO Alarm is designed for use inside a single-family home

• This CO Alarm alone is not a suitable substitute for complete

• DO NOT use this CO Alarm in warehouses, industrial or com-

easy ar

dirty or gr

burning heat source, or fuel burning appliances like a water heater.

In extremely humid areas. This Alarm should be at least 10 feet (3

om a bath or shower

meters) fr

, laundry r

washer

eas where temperature is colder than 40˚ F (4˚ C) or hotter

In ar than 100˚ F (38˚ C). These areas include non-airconditioned crawl spaces, unfinished attics, uninsulated or poorly insulated ceilings,

ches, and garages.

por

fresh air returns, or open windows. Blowing air may prevent CO from reaching the sensors.

In direct sunlight.

or apartment. It is not meant to be used in common lobbies, hallways, or basements of multi-family buildings unless working CO Alarms are also installed in each family living unit. CO Alarms in common areas may not be heard from inside individual family living units.

detection systems in places which house many people, like hotels or dormitories, unless a CO Alarm is also placed in each unit.

cial buildings, special-purpose non-residential buildings, or

mer airplanes. This CO Alarm is specifically designed for residential use, and may not provide adequate protection in non-residential applications.

en away from the unit. Teach them not to

TE THIS CO ALARM:

eas.

, sauna, humidifier

oom, utility r

oom or other sour

, dish

, vaporizer

ce of high humidity

HOW TO INSTALL YOUR CO ALARM

Read “Where To Install Your CO Alarm” before starting. Before you start installation,

included with this CO Alarm. On each label write in the phone number of your emergency responder (like 911) and a qualified appliance technician. Place one label near the CO Alarm, and the other label in the “fresh air” location you plan to go if the alarm sounds.

1. Plug the unit into a standard UNSWITCHED 120V AC outlet. The unit should be located where it can wake you if it alarms at night.

2. Make sure the POWER/ALARM light shines continuously when you plug it.

3. Test by pressing the Test/Silence button firmly until the unit sounds: four loud beeps, pause, 4 beeps. During testing, the POWER/ ALARM light will flash rapidly. This is normal.

find the pair of self-adhesive labels

AC Plug

IF YOUR CO ALARM SOUNDS

Actuation of your CO Alarm indicates the presence of carbon monoxide (CO) which can kill you. In other words, when your CO Alarm sounds, you must not ignore it!

IF THE ALARM SIGNAL SOUNDS:

1. Operate the Test/Silence button.

2. Call your emergency services, fire department or 911. Write down the number of your local emergency service here:

_____________________________________________________________

Immediately move to fresh air—outdoors or by an open door or window. Do a head count to check that all persons are accounted for. Do not re-enter the premises, or move away from the open door or window until the emergency services responder has arrived, the premises have been aired out, and your CO Alarm remains in its normal condition.

4. After following steps 1-3, if your CO Alarm reactivates within a 24-hour period, repeat steps 1-3 and call a qualified appliance technician to investigate for sources of CO from fuel-burning equipment and appliances, and inspect for proper operation of this equipment. If problems are identified during this inspection have the equipment serviced immediately. Note any combustion equipment not inspected by the technician, and consult the manufacturers’ instructions, or contact the manufacturers directly, for more information about CO safety and this equipment. Make sure that motor vehicles are not, and have not, been operating in an attached garage or adjacent to the residence. Write down the number of a qualified appliance technician here:

_____________________________________________________________

“ALARM-MOVE TO FRESH AIR”

If you hear the alar

move ever

m horn and the red light is flashing,

yone to a source of fresh air.

DO NOT unplug the CO Alarm!

Alarms have various limitations. See "General Limitations of CO Alarms" for details.

USING THE SILENCE FEATURE

ect

The Silence Featur a CO problem. Always check your home for a potential problem after any alarm. Failure to do so can result in injury or death.

NEVER unplug your CO Alarm to silence the horn. Use the silence feature. Unplugging the CO Alarm removes your protection! See “If Your CO Alarm Sounds” for details on responding to an alarm.

When CO reaches alarm levels the alarm will sound— repeating horn

n: 4 beeps, a pause, 4 beeps, etc. Pr

patter button until the horn is silent. The initial Silence cycle will last approximately 4 minutes.

NOTE: After initial 4-minute Silence cycle, the CO Alarm re-evaluates present CO levels and responds accordingly. If CO levels remain potentially dangerous—or start rising higher—the horn will start sounding again.

While the detector is silenced: If the CO Alarm...

Is silent for only 4 minutes, then starts sounding loudly— 4 beeps, pause, 4 beeps, pause

If the CO Alarm...

Remains silent after you

essed the T

pr button

e is for your convenience only and will not cor

ess and hold the T

est/Silence

This means...

CO levels ar dangerous.

This means...

CO levels are dropping.

e still potentially

est/Silence

TESTING AND MAINTENANCE

WEEKLY TESTING

est/Silence button on the Alarm cover until alarm sounds.

ess the T

Pr During testing, you will hear a loud alarm sequence – 4 beeps, pause, 4 beeps, pause.

The alarm sequence should last 5-6 seconds. If it does not alarm, make sure the unit is fully plugged into an unswitched outlet. If the unit still does not alarm, replace it immediately.

eplace it immediately

, r

ranty.

operly

ned to the manufacturer

etur

•

oducts under war

Pr for replacement. See “Limited Warranty” at the end of this manual.

• DO NOT stand close to the Alarm when the horn is sounding. Exposure at close range may be harmful to your hearing. When

testing, step away when horn starts sounding.

• NEVER use vehicle exhaust! Exhaust may cause permanent damage and voids your war

ranty may be r

m ever fails to test pr

If the Alar

REGULAR MAINTENANCE

o keep the CO Alar

est it every week as described in “W

•

• Vacuum the CO Alarm cover at least once a month, using the soft brush attachment. Never use water they may damage the unit. Test the Alarm again after vacuuming.

DO NOT spray cleaning chemicals or insect sprays directly on or near the CO Alarm. DO NOT paint over the CO Alarm. Doing so may cause permanent damage.

• Household cleaners, aerosol chemicals and other contaminants can affect the sensor. When using any of these materials near the CO Alarm, make sure the room is well ventilated.

• If your home is being fumigated, unplug the unit temporarily and put it wher fumigation is complete and all traces of fumes clear, plug the unit back in and retest it.

m working pr

e it will not be exposed to chemicals or fumes. When

operly:

esting.”

eekly T

, cleaners, or solvents, since

WHAT YOU NEED TO KNOW ABOUT CO

WHAT IS CO?

CO is an invisible, odorless, tasteless gas produced when fossil fuels do not burn completely, or are exposed to heat (usually fire). Electrical appliances typically do not produce CO.

These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline, kerosene, and propane.

Common appliances are often sources of CO. If they are not properly maintained, are improperly ventilated, or malfunction, CO levels can rise quickly. CO is a real danger now that homes are more energy efficient. “Air-tight” homes with added insulation, sealed windows, and other weatherproofing can “trap” CO inside.

SYMPTOMS OF CO POISONING

These symptoms are related to CO POISONING and should be discussed with ALL household members.

Mild Exposure:

Slight headache, nausea, vomiting, fatigue (“flu-like” symptoms).

Medium Exposure:

Throbbing headache, drowsiness, confusion, fast heart rate.

Extreme Exposure:

Convulsions, unconsciousness, heart and lung failure. Exposure to carbon monoxide can cause brain damage, death.

Some individuals are more sensitive to CO than others, including people with cardiac or respiratory problems, infants, unborn babies, pregnant mothers, or elderly people can be more quickly and severely affected by CO. Members of sensitive populations should consult their doctors for advice on taking additional precautions.

FINDING THE SOURCE OF CO AFTER AN ALARM

Carbon monoxide is an odorless, invisible gas, which often makes it difficult to locate the source of CO after an alarm. These are a few of the factors that can make it difficult to locate sources of CO:

• House well ventilated before the investigator arrives.

• Problem caused by “backdrafting.”

• Transient CO problem caused by special circumstances. Because CO may dissipate by the time an investigator arrives, it may be

dif

ficult to locate the source of CO.

gated to pay for any carbon monoxide investigation or ser

POTENTIAL SOURCES OF CO IN THE HOME

Fuel-burning appliances like: portable heater, gas or wood burning fireplace, gas kitchen range or cooktop, gas clothes dryer.

Damaged or insufficient venting: corroded or disconnected water heater vent pipe, leaking chimney pipe or flue, or cracked heat exchanger, blocked or clogged chimney opening.

Improper use of appliance/device: operating a barbecue grill or vehicle in an enclosed area (like a garage or screened porch).

ransient CO Pr

can be caused by outdoor conditions and other special cir

The following conditions can result in transient CO situations:

1. Excessive spillage or reverse venting of fuel appliances caused by outdoor conditions such as:

• Wind direction and/or velocity, including high, gusty winds. Heavy

• Negative pressure differential resulting from the use of exhaust

•

• Vent pipe connections vibrating loose from clothes dryers,

• Obstructions in or unconventional vent pipe designs which can

Extended operation of unvented fuel bur

2. fir

3. Temperature inversions, which can trap exhaust close to the ground. Car idling in an open or closed attached garage, or near a home.

These conditions are dangerous because they can trap exhaust in your home. Since these conditions can come and go, they are also hard to recreate during a CO investigation.

oblems:

air in the vent pipes (cold/humid air with extended periods between cycles).

fans. Several appliances running at the same time competing for limited

fresh air.

naces, or water heaters.

fur

amplify the above situations.

eplace).

HOW CAN I PROTECT MY FAMILY?

A CO Alarm is an excellent means of protection. It monitors the air and sounds a loud alarm before carbon monoxide levels become threatening for average, healthy adults.

m is not a substitute for pr

A CO Alar appliances.

To help prevent CO problems and reduce the risk of CO poisoning:

Clean chimneys and flues yearly

• and nests for proper air flow. Also, have a professional check for rust and corrosion, cracks, or separations. These conditions can

oper air movement and cause backdrafting. Never “cap”

event pr

pr or cover a chimney in any way that would block air flow.

• Test and maintain all fuel-burning equipment annually. Many local gas or oil companies and HVAC companies offer appliance inspections for a nominal fee.

• Make regular visual inspections of all fuel-burning appliances. Check appliances for excessive rust and scaling. Also check the flame on the burner and pilot lights. The flame should be blue. A yellow flame means fuel is not being burned completely and CO

esent. Keep the blower door on the furnace closed. Use

may be pr vents or fans when they are available on all fuel-burning appliances. Make sure appliances are vented to the outside. Do not grill or barbecue indoors, or in garages or on scr

Check for exhaust backflow fr

• hood on an operating furnace for a backdraft. Look for cracks on

nace heat exchangers.

fur

• Check the house or garage on the other side of shared wall.

• Keep windows and doors open slightly. If you suspect that CO is escaping into your home, open a window or a door windows and doors can significantly decr

In addition, familiarize yourself with all enclosed materials. Read this manual in its entir do if your CO Alarm sounds.

ety, and make sure you understand what to

BRK Brands, Inc. shall not be obli

“transient” or on-again-of

ning devices (range, oven,

oper maintenance of home

. Keep them fr

een porches.

om CO sour

ces. Check the draft

ease CO levels.

vice call.

cumstances.

. Opening

oblems

f-again CO pr

ee of debris, leaves,

REGULATORY INFORMATION FOR CO ALARMS

WHAT LEVELS OF CO CAUSE AN ALARM?

Underwriters Laboratories Inc. Standard UL2034 requires residential CO Alarms to sound when exposed to levels of CO and exposure times as described below. CO levels are measured in parts per million (ppm) of CO over time (in minutes).

UL2034 Required Alarm Points*:

• If the alarm is exposed to 400 ppm of CO, IT MUST ALARM BETWEEN 4 and 15 MINUTES

• If the alarm is exposed to 150 ppm of CO, IT MUST ALARM BETWEEN 10 and 50 MINUTES.

• If the alarm is exposed to 70 ppm of CO, IT MUST ALARM BETWEEN 60 and 240 MINUTES.

* Approximately 10% COHb exposure at levels of 10% to 95% Relative Humidity (RH).

The unit is designed not to alarm when exposed to a constant level of 30 ppm for 30 days.

CO Alarms are designed to alarm before there is an immediate life threat. Since you cannot see or smell CO, never assume it’s not present.

• An exposure to 100 ppm of CO for 20 minutes may not affect average, healthy adults, but after 4 hours the same level may cause headaches.

• An exposure to 400 ppm of CO may cause headaches in average, healthy adults after 35 minutes, but can cause death after 2 hours.

This CO Alarm measures exposure to CO over time. It alarms if CO levels are extremely high in a short period of time, or if CO levels reach a certain minimum over a long period of time. The CO Alarm generally sounds an alarm before the onset of symptoms in average, healthy adults.

Why is this important? Because you need to be warned of a potential CO problem while you can still react in time. In many reported cases of CO exposure, victims may be aware that they are not feeling well, but become disoriented and can no longer react well enough to exit the building or get help. Also, young children and pets may be the first affected. The average healthy adult might not feel any symptoms when the CO Alarm sounds. However, people with cardiac or respiratory problems, infants, unborn babies, pregnant mothers, or elderly people can be more quickly and severely affected by CO. If you experience even mild symptoms of CO poisoning, consult your doctor immediately!

Standards: Underwriters Laboratories Inc. Single and Multiple Station carbon monoxide alarms UL2034.

According to Underwriters Laboratories Inc. UL2034, Section 1-1.2: “Carbon monoxide alarms covered by these requirements are intended to respond to the presence of carbon monoxide from sources such as, but not limited to, exhaust from internal-combustion engines, abnormal operation of fuel-fired appliances, and fireplaces. CO Alarms are intended to alarm at carbon monoxide levels below those that could cause a loss of ability to react to the dangers of Carbon Monoxide exposure.” This CO Alarm monitors the air at the Alarm, and is designed to alarm before CO levels become life threatening. This allows you precious time to leave the house and correct the problem. This is only possible if Alarms are located, installed, and maintained as described in this manual.

Gas Detection at Typical Temperature and Humidity Ranges: The CO Alarm is not formulated to detect CO levels below 30 ppm typically. UL tested for false alarm resistance to Methane (500 ppm), Butane (300 ppm), Heptane (500 ppm), Ethyl Acetate (200 ppm), Isopropyl Alcohol (200 ppm) and Carbon Dioxide (5000 ppm). Values measure gas and vapor concentrations in parts per million.

Audible Alarm:85 dB minimum at 10 feet (3 meters).

GENERAL LIMITATIONS OF CO ALARMS

This CO Alarm is intended for residential use. It is not intended for use in industrial applications where Occupational Safety and Health Administration (OSHA) requirements for carbon monoxide detectors must be met.

CO alarms may not waken all individuals.

readily waken to the sound of the CO alarm, or if there are infants or family members with mobility limitations, make sure that someone is assigned to assist them in the event of an emergency.

CO Alarms will not work without power. This CO Alarm requires a continuous supply of AC power. Plug into an unswitched 120V AC outlet only.

CO Alarms for Solar or Wind Energy users and battery backup power systems: AC powered CO Alarms should only be operated with

true or pure sine wave inverters. Operating this CO Alarm with most battery-powered UPS (uninterruptible power supply) products or square wave or “quasi sine wave” inverters will damage the Alarm. If you are not sure about your inverter or UPS type, please consult with the manufacturer to verify.

This CO Alarm will not sense carbon monoxide that does not reach the sensor. This CO Alarm will only sense CO at the sensor. CO may be

present in other areas. Doors or other obstructions may affect the rate at which CO reaches the CO Alarm. For this reason, if bedroom doors are usually closed at night, we recommend you install a CO Alarm in each bedroom and in the hallway between them.

CO Alarms may not sense CO on another level of the home. For example, a CO Alarm on the second level, near the bedrooms, may not sense CO in the basement. For this reason, one CO Alarm may not give adequate warning. Complete coverage is recommended. Place CO Alarms on each level of the home.

If children or others do not

CO Alarms may not be heard. The alarm horn loudness meets or exceeds current UL standards of 85 dB at 10 feet (3 meters). However, if the CO Alarm is installed outside the bedroom, it may not wake up a sound sleeper or one who has recently used drugs or has been drinking alcoholic beverages. This is especially true if the door is closed or only partly open. Even persons who are awake may not hear the alarm horn if the sound is blocked by distance or closed doors. Noise from traffic, stereo, radio, television, air conditioner, or other appliances may also prevent alert persons from hearing the alarm horn. This CO Alarm is not intended for people who are hearing impaired.

CO Alarms are not a substitute for a smoke alarm. Although fire is a source of carbon monoxide, this CO Alarm does not sense smoke or fire. This CO Alarm senses CO that may be escaping unnoticed from malfunctioning furnaces, appliances, or other sources. Early warning of fire requires the installation of smoke alarms.

CO Alarms are not a substitute for life insurance. Though these CO Alarms warn against increasing CO levels, BRK Brands, Inc. does not warrant or imply in any way that they will protect lives from CO poisoning. Homeowners and renters must still insure their lives.

CO Alarms have a limited life. Although the CO Alarm and all of its parts have passed many stringent tests and are designed to be as reliable as possible, any of these parts could fail at any time. Therefore, you must test your CO Alarm weekly

CO Alarms are not foolproof. Like all other electronic devices, CO Alarms have limitations. They can only detect CO that reaches their sensors. They may not give early warning to rising CO levels if the CO is coming from a remote part of the home, away from the CO Alarm.

TROUBLESHOOTING GUIDE

PROBLEM...

Red light is OFF

ess the Test/Silence button.

The light flashes (RED) and the hor quick “chirps” every minute.

CO Alarm goes back into alarm 4 minutes after you pr

CO Alarm sounds frequently even though no high levels of CO are revealed in an investigation.

If you have any questions that cannot be answered by reading this manual, call Consumer Affairs at 1-800-323-9005.

BRK Brands, Inc. ("BRK") the maker of First Alert®brand pr will be free from defects in material and workmanship. BRK, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the pr

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales

eceipt. Pr

r not have the right to alter, modify or any way change the terms and conditions of this warranty.

This warranty does not cover normal wear of parts or damage r on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center. Further, the warranty does not cover acts of God, such as fire, flood, hurricanes and tornadoes or any batteries that ar

BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent pr duration of the above warranty damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state, or province to province.

. Unit will not alarm when you

est/Silence button.

ess the T

oduct is no longer available, r

chase is r

oof of pur

e included with this unit.

ohibited by applicable law

n sounds 3

eplacement may be made with a similar pr

ed to obtain warranty performance. BRK dealers, service centers, or retail stores selling BRK products do

equir

, any implied warranty of mer

. Some states, pr

How to Obtain Warranty Service

vice r

equir

etur

ed, do not r

n to:

BRK Brands, Inc., 25 Spur Drive, El Paso, TX 79906

vice:

Ser

If service is r Division at 1-800-323-9005, 7:30 AM to 5:00 PM, Central Standard Time, Monday through Friday. To assist in serving you, please have the model number and date of purchase available when calling.

ranty Ser

For W

For your records, please record:

Date Purchased: __________________

e Purchased: _______________________

Wher

Date Installed: ____________/____________Month/Y

THIS MEANS... YOU SHOULD...

CO Alarms may not be plugged all the way in, or

eceiving power.

is not r

MALFUNCTION SIGNAL. CO replaced.

CO levels indicate a potentially danger situation.

The CO Alarm may be improperly located. Refer to “Where to Install CO Alarms.”

LIMITED W

Alarm needs to be

ous

ARRANTY

oducts, warrants that for a period of 5 years fr

oduct of equal or gr

om any of the following: negligent use or misuse of the pr

esulting fr

ovinces, or jurisdictions do not allow the exclusion or limitation of incidental or consequential

n the product to your retailer. In order to obtain warranty service, contact the Consumer Affairs

etur

chantability or fitness for a particular purpose is limited in duration to the

Gently push unit all the way into outlet. Make

e it is not plugged into an outlet controlled by

sur a switch.

e unit is plugged in secur

Make sur CO Alarms under warranty should be returned to manufactur

arranty” for details.

IF YOU ARE FEELING SYMPTOMS OF CO POISONING, EV or the Fire Department. If not, press the Test/ Silence button again and keep ventilating your

home.

Relocate your Alarm. If frequent alarms continue, have home rechecked for potential CO problems. You may be experiencing an intermittent CO problem.

eplacement. See “Limited

er for r

TE your home and call 911

ACUA

om the date of purchase, this product

eater value This is your exclusive warranty

Replacement date is five years after installation:

_____________/____________Month/Year

eaches the end of

ear

NOTE: End of Life Signal — Once the unit r its lifecycle, the MALFUNCTION SIGNAL will sound once a minute to indicate the need to immediately replace the Alarm.

First Alert®is a registered trademark of the First Alert Trust.

Printed in Mexico M08-0152-002 S 07/07

ely

oduct, use