BRK electronic BF5, FE5R User Manual

User’s Manual

MOUNTING

STRAP

MOUNTING  STRAP PINS

WALL 

RECEPTACLE

EXTINGUISHER 

HANDLE

WALL

ire Extinguishers

AT. N O.

BF5

8-0090-002

IMPORTANT! Please read carefully and save.

This user’s manual contains important information about your fire exting

uisher’s operation. If you are installing this fire extinguisher for use by

others, you must leave this manual—or a copy of it—with the end user. Read e

nstalling or using the unit. Make sure everyone in your household is

com

pletely familiar with the operation of the extinguisher, and review

he instructions regularly. In an emergency, you will not have time to

ead instructions.

TABLE OF CONTENTS

Important Information About Fire Extinguishers . . . . . . . . . . . . . . .1

Read Before Installing or Using This Fire Extinguisher . . . . . . . . .1

Where t

How to Install This Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Checking and Inspecting the Fire Extinguisher . . . . . . . . . . . . . .2-3

ow to Operate Your Fire Extinguisher in a Fire Emergency . . . . .3

After the Fire is Extinguished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

How to Clean After Us

If Your Fire Extinguisher Needs Service . . . . . . . . . . . . . . . . . . . . . .4

isposing of a Used Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

IMPORTANT INFORMATION ABOUT FIRE EXTINGUISHERS

NOTE: Be sure the extinguisher is rated to fight the type of fire most likely to occur in the area you choose to install it. Since household fires commonly start in the kitchen, you should always install an extinguisher in the kitchen. For added security, you should also install additional extinguishers in utility areas, and other living areas in your household.

ire extinguishers are classified by fire type. The A, B and C

ng system defines the kinds of burning materials each fire

tinguisher is designed to fight. The numbers in front of the

e A, B, or C indicate the rating for size of the fire the unit can extinguish. Using the wrong type of fire extinguisher can do

ore harm than g

m extinguisher to use on each class of fire!

BF5 is rated 5-B:C. It is NOT rated to fight Class A fires.

READ BEFORE INSTALLING OR USING THIS FIRE EXTINGUISHER!

• This extinguisher is designed for use against small fires that e j

ha designed to fight large fires that are burning out of control. If the fire is too hot or smoky for you to get within 6 feet (2 meters) of it, do not try to fight it yourself. Warn everyone, evacuate the premises, and have someone call the Fire Department from outside the building. Trying to fight a large

re y

• Do not puncture or burn any fire extinguisher. The contents

are under pressure, and the extinguisher could explode.

• Never locate this extinguisher close to an engine, stove or

other source of heat. It is pressurized and could rupture or explode if exposed to temperatures over 150° F (66° C).

• This extinguisher contains a dry powder extinguishing agent.

The agent/powder is nontoxic, but can irritate skin. When using this unit, avoid breathing the powder. Always ventilate the area after use.

M 0

2/07

xtinguisher label and the entire user’s manual carefully before

o Install This Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . . . .2

ing a Fire Extinguisher . . . . . . . . . . . . . . . . .4

ood. Make sure you understand which fire

Class A rating:

fighting small fires involving wood, paper, cloth, rubber, and some plastics.

Class B rating: The agent/powder is suitable for fighting small fires involving grease, oil, gasoline,

erosene, and other flammable liquids.

ass C ra

fighting small fires in "live" electrical equipment.

ust started and are small enough to fight safely. It is not

elf can result i

our

The agent/powder is suitable for

ting:

n i

ent/powder is suitable for

he ag

jury or death.

1 2 3 4

Model

E5R

RE TO INSTALL THIS EXTINGUISHER

WHE

Fire Extinguisher Should Be Mounted:

•

In the vicinity of (but not on or in) a potential source of heat and/or fi

•

• In a location that is convenient, in plain sight, and 3-1/2 to 5

•

HOW TO INSTALL THIS EXTINGUISHER

NOTE: Since surface types vary, mounting screws are not included. Purchase screws or bolts specifically designed for the surface on w

hich you will mount the fire extinguisher. The fire extinguisher label

lists its maximum weight.

•

move mounting bracket from extinguisher by unlocking the clasp and pulling the bracket away from the extinguisher. Use two strong screws (such as #8 machine screws) to mount the bracket securely on

to metal or another solid surface that can support the weight of the fire extinguisher. The mounting bracket must be secure so you can remove the extinguisher quickly in an emergency.

1. Install the mounting bracket

2. After installing the mounting

BF5 for Mobile Homes only.

This extinguisher can be mounted in the special wall receptacle provided in your mobile home or on a wall bracket (bracket can only be purchased through Consumer Affairs: 800-323-9005 and order part number B70-78-00). Position the mounting strap across the extinguisher to secure the extinguisher. The label should face outward so it can be easily read. See Figure.

ing the mounting bracket

B7 instructions number 1 and 2 above.

re, like an oven or stove.

Where it is easy to reach, near an exit or an escape route from the room.

eet (1 to 1.5 meters) above the floor.

Store the extinguisher high enough to keep it out of the reach o

f small children.

On a clean, dry surface where the temperature does not go above 120° F (49° C) or below –40° F (–40° C).

Do not mount the extinguisher on drywall or plaster without adequate support. Use strong screws or bolts to mount the bra

cket securely into solid wood or metal that can support it,

ike a wooden partition stud. Secure mounting is needed so you can remove the extinguisher quickly and easily in an emergen

cy. Also, if the extinguisher is not held securely, it could

op to the floor and injure people or damage the extinguisher

Do not break the plastic loop holding the safety pin in place! This loop prevents accidental discharge of the fire e

xtinguisher. Break the loop only in an emergency before

ing the fire extinguisher.

as shown in “Installing The Mounting Bracket” using strong screws (such as #8 machine screws) with washers and nuts. The screws should not be longer than necessary to accommodate a washer and nut. Mounting screws, washers, and nuts are not included (see Note above.)

bracket, replace the extinguisher on the bracket.

If you are

78-00, follow mounting

Installing the

Mounting Brac

Bracket B70-78-00

Properly Installed

Extinguisher in Wall

Receptacle

ket

CHECKING AND INSPECTING THE FIRE EXTINGUISHER

DO NOT CHECK THE PRESSURE OR TEST THE FIRE EXTINGUISHER BY SQUEEZING THE TRIGGER, EVEN BRIEFLY. ONCE USED IT WILL GRADUALLY LOSE PRESSURE AND WILL

OT BE FULLY CHARGED FOR USE IN AN EMERGENCY.

1. Inspect and test the extinguisher once a eek. Start by removing the extinguisher

w from the mounting bracket/cap. Check the extinguisher pressure by pressing the green button on top of the cap as

“Checking the Pressure.”

n i

sho If the button pops back up, the

uisher is properly pressurized

e and ready to use. If the button stays down, the extinguisher has lost pressure

nd must be replaced.

ck for signs of damage or misuse.

Make sure you can still read all the text on the label. Carefully examine the surface of the extinguisher for corrosion.

n hel

ou ca

Y cleaning the extinguisher if it gets wet or dirty. If you notice corrosion during the warranty period, return

nit to First Alert

he u

t manual).

ent corrosion by

p pr

imited Warranty" at the end of this

e "L

(se

Checking the

ssure

Pre

Continued...

CHECKING AND INSPECTING THE FIRE EXTINGUISHER, Continued

. Make sure the tamper indicator

(“

safety seal”) is still intact as shown in “Location Of The ‘Safety Seal’” and t

he nozzle is clean and unobstructed.

. When you finish inspecting the fire

extinguisher, always put it back into the mou

nting bracket. Make sure the han-

le is locked down and the safety seal

is intact.

or more information about fire extinguishers, consult the NFPA Standard #10, “Portable Fire Extinguishers,” available from the National Fire Protection Association, Inc., Batterymarch Park, Quincy, MA 02169, U

SA.

W TO OPERATE YOUR FIRE

cation of the

“

Safety Seal”

EXTINGUISHER IN A FIRE EMERGENCY

•

Make sure your extinguisher may be safely and effectively us

ed on the small fire you want to fight. Always use extreme caution when fighting any fire. Fight a fire only where there is a clear escape p ge

ts worse.

• Avoid breathing smoke and heated fumes; stay low if necessary. Burning materials will release toxic fumes. I

nhaling these fumes may cause injury or death.

• Always stand back far enough away from the fire—near an exit—and make sure nothing is between you and your escape r burned or hit by splattering material like grease. If the fire is too hot or smoky for you to get within 6 feet (2 meters), DO N

OT try to fight the fire yourself. Evacuate immediately and

call the F

• For fires on a kitchen stove, turn oven or burners off i

mmediately if possible. If you can’t reach the oven or burner

controls safely, extinguish the fire first, then turn them off.

•

Fight the fire from an upwind direction with your back to any str

ong air current. Trying to fight a fire with currents blowing

towards you can result in serious injury.

TO FIGHT THE FIRE

• This unit will not operate with mounting bracket or mounting

strap attached. The extinguisher must be removed from the mounting bracket or mounting strap in order to discharge its contents to fight a fire.

1. Remove the extinguisher from the mounting bracket or mounting strap.

2. Hold the unit firmly with the nozzle facing away from you. Pull out the pin to break the “Safety Seal”. You won’t be able to squeeze the trigger until the safety seal is removed.

3. Stand back 6 feet (2 meters) from the fire

4. Hold the extinguisher upright and aim the

. Press and hold the trigger to discharge the

6. Sweep the spray at the base of the burning

7. Move slowly towards the fire as the

8. Completely discharge the contents of the extinguisher and make

9. For kitchen fires on a kitchen stove, turn off the stove immediately

10. If you suspect a fire had an electrical origin, shut off the electrical

ke sure the fire is not between you

nd ma

a and your exit.

nozzle at the base of the fire.

material, using quick side-to-side motions. (If the spray scatters the fire, move back.)

extinguisher spray pushes the fire back.

ntain a 6-foot (2 meter) distance between

M you and the front of the fire at all times.

sure the fire is completely out. Flashbacks are common with fires.

if possible, otherwise as soon as it is safe.

if possible, without eliminating your escape route. Do not

po touch electrical wires or appliances.

After you have completely discharged your extinguisher, leave the

building and close all the doors behind you.

ath to allow you to get out safely if the fire

oute. If you get too close to a fire, you risk getting

ire Department.

Breaking the

Safety Seal

ss and Hold

Pre

Discharge Powder

rig

TER THE FIRE IS EXTINGUISHED

Do not turn the electrical power back on or plug in any appliances until the area has been cleaned up completely. It is very important t

o remove the powder from electrical equipment after a fire. If the powder gets wet, it can conduct electricity. (Using a dry chemical extinguisher on wet electrical equipment may be hazardous for this reas

on.) This may worsen an electrical leakage problem, impair the

equipment’s insulation, or create an electrical shock hazard. If the fire was on a kitchen stove:

•

Make sure the oven and all burners are turned off.

•

Clean up the powder completely before using the stove or oven. See “How to Clean After Using a Fire Extinguisher”. Ventilate the ar

ea thoroughly.

If you think the fire had an electrical origin:

• Shut off the electrical power, if possible--do not touch any

ele

ctrical wires or appliances.

•

Leave the building and close all doors behind you. Call the Fire D

epartment and have them inspect the entire house. As soon as

they say it’s safe to return, ventilate the area thoroughly.

•

Have a licensed electrician inspect your electrical system. Do not turn the power back on or plug in any electrical equipment until the inspection has been completed.

HOW TO CLEAN AFTER USING A FIRE EXTINGUISHER

OTE:The powder spray from the extinguisher may spread over a

ide area, and may soil upholstery, carpets and walls.

• Sweep/vacuum up as much of the powder as possible.Then use

a damp cloth to wipe off the remaining agent.

• If you have any questions about cleaning appliances that the

ent has come into contact with, please contact the appliance

nufacturer.

IF YOUR EXTINGUISHER NEEDS SERVICE

his fire extinguisher is a disposable device that is NOT rechargeable.

Do not try to service or repair this fire extinguisher under any circumstances. Do not try to remove the nozzle or valve assembly. This is a pressurized device that can cause serious injury if tampered with.

If there is a problem and it is still under warranty, please see “How to Obtain Warranty Service” in the Limited Warranty.

DISPOSING OF A USED EXTINGUISHER

Completely discharge the extinguisher outdoors by turning the unit upside down and pulling the trigger. Dispose of the empty unit properly and replace it with a new fire extinguisher.

Never puncture, burn or expose this fire extinguisher to temperatures over 150° F (66° C) even if it is fully discharged.The contents are under pressure and it could explode.

LIMITED WARRANTY

BRK Brands, Inc. ("BRK") the maker of First Alert®brand products warrants that for a period of five years from the date of purchase, this product will be free from defects in material and workmanship. BRK, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period.

lacement will be made with a new or remanufactured product or

Re component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your

clusive warranty.

his warranty is valid for the original retail purchaser from the date of

ail purchase and is not transferable. Keep the original sales

l r

i receipt. Proof of purchase is required to obtain warranty performance. BRK dealers, service centers, or retail stores selling First Alert

s do not have the right to alter, modify or any way change

uct

pr the terms and conditions of this warranty.

This warranty does not cover normal wear of parts or damage result-

ny of the following: negligent use or misuse of the product,

om a

ng f

i use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center. Further, the warranty does not

r act

K sha

B caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of

rchantability or fitness for a particular purpose is limited in duration

me to the duration of the above warranty. Some states, provinces, or

isd

j consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.This warranty gives you specific legal rights, and you may also have other

s t

w t

retailer. In order to obtain warranty service, contact the Consumer Affairs Division at 1-800-323-9005, 7:30 AM to 5:00 PM, Central

tandard Time, Monday through Friday. To assist in serving you,

lease ha

p calling.

ddress:25 Sp

First Alert®is a registered trademark of the First Alert Trust.

od, such as fire, flood, hurricanes and tornadoes.

f G

s o

iable for any incidental or consequential damages

t be l

l no

ictions do not allow the exclusion or limitation of incidental or

hat vary from state to state, or province to province.

tain Warranty Service:

o O

ce:

f se

e t

equired, do not return the product to your

ice is r

mber and date of purchase available when

el n

he mod

, El Paso, TX 79906

ur D

8-00

90-002

M 0

2/0