BRK electronic 7010BSL User Manual
SMOKE&
STROBE
COMBO
PHOTOELECTRIC
CAT.
7010BSL
INTEGRATED
SMOKE ALARM &
STROBE LIGHT
One device includes both a strobe light
and photoelectric smoke alarm. Requires only one electrical box. Saves
installation time.
SMART STROBE
Separate fl ash patterns to distinguish
between smoke and carbon monoxide.
177 CANDELA
XENON STROBE
Powerful 177 candela xenon strobe light
provides effective visual warning to
hearing impaired residents.
1Hz FLASH RATE
60 fl ashes per minute rate meets
ADA, ANSI 117.1, NFPA 72 and UL1971
requirements for visual signal devices.
120V AC, 60Hz Wire-in
with two AAA Battery Backup for Alarm
Description:
The BRK Brands, Inc. Model Number 7010BSL is a wire-in, 120V AC 60Hz single
and/or multiple station photoelectric smoke alarm with integrated 177 candela
strobe light specifi cally designed for residential and institutional applications
including sleeping rooms of hospitals, hotels, motels, dormitories and other multifamily dwellings as defi ned in standard NFPA 101. Model 7010BSL complies
with UL217, UL1971, CSFM, NFPA 72, HUD, FHA and other agencies that model
their codes after the above agencies. They meet building codes where AC with
battery backup, silence, photoelectric smoke alarms are required. The alarms are
interconnectable with up to 18 devices, of which 12 can be smoke alarms.
The BRK 7010BSL alarms feature a photoelectric smoke sensing chamber, an integrated 177 candela strobe light, an 85dB horn and AAA battery back-up for
alarm. The Strobe Light is designed to provide hearing impaired individuals with a
visual warning of a fi re. The Smart Strobe has separate fl ash patterns for smoke/
heat and carbon monoxide dangers (when connected to a First Alert CO alarm).
This helps a hearing impaired person better distinguish the danger present. The
177 candela Xenon strobe meets UL 1971 requirements and fl ashes at a rate of
an average of 60 times a minute. This alarm features two latching features and
two silence features. Alarm Latch: Easily identifi es initiating alarm even after alarm
condition has subsided. Low Battery Latch: Identifi es which unit is in low battery condition by blinking the green power light. Low Battery Silence: Temporarily
silence the low battery chirp for up to eight hours. Alarm Silence: Silence alarm
for several minutes. Optipath 360 technology provides 360 degrees of direct access to the smoke sensing chamber. Replace battery without removing alarm from
ceiling. Other Contractor preferred features include a dust cover, keyhole slots
in the mounting bracket eliminate the need
to remove the electrical box screws for
installation, two locking features
and a “Quick-Connect” wiring
harness.
bracket eliminate the need
trical box screws for
locking features
nnect” wiring
OPTIPATH 360
TECHNOLOGY TM
Provides 360 degrees of direct access
to the smoke sensing chamber.
BATTERY BACKUP
Two AAA batteries provide backup for
the smoke alarm during power outages.
(Note: will not power the strobe light).
CAT.
7010BSL
TOP VIEW
5.0"
SIDE VIEW
4.0"
ARCHITECTURAL AND ENGINEERING SPEC
The integrated strobe light & smoke alarm shall be a BRK Model 7010BSL and shall
provide at a minimum the following features and functions:
1. A photoelectric smoke sensing chamber.
2. A 177 candela Xenon strobe light. The Smart Strobe shall have separate fl ash
patterns to distinguish between smoke/heat and carbon monoxide dangers.
3. Fully screened sensing chamber to resist entry of small insects thereby reducing
the probability of unwanted alarms.
4. Powered by 120V AC, 60Hz and have a monitored two AAA battery backup for alarm
and a solid state piezo horn rated at 85dB at 10 ft and be capable of self restoring.
5. A visual green LED power-on indicator to confi rm unit is receiving power or is in
alarm.
6. A full function test button should check all alarm functions by simulating a smoke
condition, causing the unit to alarm.
7. Two Latching features: Alarm Latch to easily identify initiating alarm after alarm
condition has subsided. Low battery latch: to visually identify which unit is in
low battery condition. Two Silence Features: Alarm Silence to temporarily silence
nuisance alarms. Low Battery Silence to silence low battery chirp for up to 8 hours.
8. Two Locking features - tamper resistant locking pins that lock battery drawer and/
or alarm to mounting bracket.
9. The unit shall be capable of operating between 40°F (4°C) and 100°F (38°C) and
relative humidity between 10% and 90%.
10. The unit shall have a plug in connector and be capable of interconnection of up to
18 alarms, 12 of which can be smoke alarms.
11. The unit shall at a minimum meet the requirements of UL217, UL1971, ADA, ANSI
117.1, CSFM, NFPA 72, NFPA 101 and the ICC.
INSTALLATION OF ALARM
Installation of this smoke alarm must conform to all local electrical
codes and Article 760 of the National Electrical Code (NFPA 70)
and NFPA 72. Interconnected units must meet the following
requirements: Total length of wire interconnecting units should
be less than 1000 feet, be #18 gauge or larger and be rated at
least 300V. It is recommended that all units be on the same fuse
or circuit breaker. If local codes do not permit, be sure the neutral
wire is common to both phases.
THE PARTS OF THIS SMOKE ALARM
1
3
4
7
2
2
1. Mounting bracket
6
8
2. Mounting Slots
3. Locking Pins
4. Hot (Black) AC Wire
5
5. Neutral (White) AC Wire
6. Interconnect (Orange) Wire
7. Pull-out Battery Drawer
8. Quick-Connect Plug
B. To additional units; Maximum = 18 total
(Maximum 12 Smoke Alarms)
1a. Smoke Alarm 5. Electrical Box
1b. Smoke/Strobe Combo 6. Neutral Wire (White)
2. Ceiling or Wall 7. Interconnect Wire (Orange)
3. Power Connector 8. Hot Wire (Black)
4. Wire Nut
A. Unswitched 120VAC 60 Hz source
MOUNTING
BRACKET
B
}
678
}
A
43 1a5
5 2
43 1b
UL1971 Signaling Devices Light Dispersion Chart
Angle
LIGHT
90 90
45 45
FIGURE 1: Light Output
for Ceiling Mount
CEILING
0
(In Degrees)
5-25
30-45
Percent
Light Intensity
0
50
55
60
65
70
75
80
85
90
100
90
75
55
45
40
35
35
30
30
25
25
FIGURE 2: Light Output
for Wall Mount
90
45
WALL
0
LIGHT
45
90
TECHNICAL SPECS
Alarm Dimensions: 5.1” dia x 4.0”H
Weight: 10.9 oz
Operating Voltage: 120V AC 60Hz w/ two AAA battery backup for alarm
Voltage Range: 108V AC to 132V AC
Operating Current: 0.05/0.60 amps (standby/alarm)
Temperature Range: 40°F (4°C) to 100°F (38°C)
Humidity Range: 10% to 90% relative humidity (RH)
Audio Alarm: 85dB at 10 feet
Test/Silence: Electronically simulates smoke condition, causing the unit
to alarm. Press and hold test/silence button
Alarm Reset: Automatic when smoke clears
Interconnections: Up to 18 units of First Alert or BRK Smoke, CO and Heat
Alarms. Maximum of 12 smoke alarms. See user’s manual
for details.
Smoke Sensor: Photoelectric
Strobe Light: 177 candela Xenon strobe
Flash Rate: 1 Hz.
Smoke Alarm: Constant approx. 1 fl ash per second.
CO Alarm: Intermittent approx. 1 fl ash per second for four
fl ashes, then 5 seconds off. Pattern is repeated.
Indicator Lights/Sounds:
AC Power: Constant Green LED
DC Power: Intermittent Red LED
Local Alarm: Red LED fl ashes rapidly, steady fl ashing strobe
Remote Alarm: Red LED out.
Listing: Listed to UL217 & UL1971 Standards
SHIPPING SPECS
Individual Carton Dimensions 5.25”L x 4.13”W x 5.44”H
Weight 0.97 lbs.
Cube 0.07 ft3
UPC 0 29054 12104 2
Master Carton Dimensions 12.63”L x 5.81”W x 5.94”H
Master Pack 3
Weight 3.24 lbs.
Cube: 0.25 ft3
I2of5: 300 29054 12104 3
Pallet Information
Cases per Layer 24
Number of Layers: 7
Cases per Pallet: 168
Units per Pallet: 504
Cube: 47.5 ft3
Weight: 609 lbs.
©2011 BRK Brands, Inc. a Jarden Corporation
Company (NYSE: JAH)
3901 Liberty Street Road
Aurora, IL 60504-8122
All rights reserved
First Alert is a registered trademark of the First Alert Trust
brkelectronics.com
BRK is a registered trademark of BRK Brands, Inc.
CM3032
Loading...