Page 1
29004091
Your Real Time Electricity Monitor is Now Up
and Running
Setting Your Clock
To set the clock please follow the se steps.
•
To set the clock, hold the Centre Button on the Display until the LED fl ashes.
When you let go the screen will clear and the clock hours will fl ash.
•
Use the Up and Down buttons to set the hour - the Monitor has a 24 hour clock.
Once the correct hour is selected press the C entre button to accept.
•
The minutes will now fl ash. Use the Up and Down but tons to set the minutes.
•
Push the Centre button, and the display will return to normal operation.
Setting Your Electricity Price
Your monitor has been set with a n average unit rate of 13.96 p/kWh.
If you wish to change this f ollow these steps.
•
Press the Up button for three seconds until the LED fl ashes and release.
•
Push the Up or Down button to change between Euros and Pounds and press
the Centre button to confi rm.
•
The unit price will start fl ashing. Press the Up or Down button to adjust the price
of the electricity fi rst three digits - press the Centre button to confi rm.
•
Repeat this process to set the last digits - press the Centre button to c onfi rm.
•
The display will return to normal operation. Your new electricity price has now
been set.
The unit has been set up for si ngle rate meters. If you have a two rate meter
such as Economy 7 follow the se steps.
•
Press and hold the Up and Down buttons together for three seconds until
the LED fl ashes and release
•
Use the Up and Down buttons to set your low rate tariff. Press the Centre but ton
to confi rm.
•
The clock will start to fl ash. Use the Up and Down buttons to set the time
the low rate starts. Press the Centre button to c onfi rm.
•
Repeat these steps to set the time for your second rate.
•
The display will return to normal operation.
Frequently Asked Questions
Why is my screen showing a seri es of dashes?
The display needs pairing to the Transmitter – refer to ‘Setting Up’.
Why is my screen showing ‘0 wat ts’?
The display is ready to use – refer to ‘Setting Up’ to continue with installation.
My display has a corrupt /no display?
Check the monitor is properly connected to the power supply.
If your monitor still does not work properly see the ‘Contact Us’ section.
My readings don’t see m to be consistent with my consumptio n?
There is a very small chance your Monitor is receiving a signal from another
transmitter. Repeat the pairing of your transmitter again.
Why does the data on th e display never change?
The unit may not have been set up correctly. You should start the set up process again.
Why does the temper ature reading seem too high?
This Display may be too close to a heat source; try moving it to a
different location.
Why does the cost seem t o be incorrect?
Follow the process in the ‘Setting Your Electricity Price’ sect ion to set your
preferred price.
For more information on setting up your Real Time Electricity M onitor, there is a
video tutorial available at
www.currentcos t.com/britishgas
If you have any other problems you cannot fi x, do not attempt to repair the
equipment, disconnect the Sensor and Monitor and refer to the ‘Contact Us’ section.
Additional Accessories
There are additional accessories available for your Real Time Electricity M onitor.
This includes additional monitors, additional sensors for use with 3-phase meters,
plug socket sensors to monitor individual appliances in the home, and cables to
download your consumption history to a PC.
Contact Us
If you have any questions please contact us by email at
energyeffi ciencyteam@britishgas.co.uk
If you have a faulty monitor please return to Freepost NWW1657, PO Box 7,
Manchester M19 2PB including your full name and address.
4 5
Your energy experts
Real Time
Electricity Monitor
Instruction Manual
Down
D
own
p
DAY
ELECTRIC
C
Page 2
Setting Up
•
Connect the Power Supply in Figure 1 to the port on the back of the Monitor
and plug into a power socket.
•
Remove the plastic tab from the back of the Transmitter – this will activate
the battery.
•
If the display shows ‘0 watts’ it is ready to use - proceed to ‘Fitting the Sensor
Jaw and Transmitter to the Cable’ section. If it doesn’t it requires pairing with
the transmitter, see next section.
Pairing the Display and Transmitter
•
Locate the tuning push switch on the front in the centre of the Transmitter, Figure 2.
•
Using a ballpoint pen, push and hold the switch for nine seconds. Upon releasing, the
red light on the Transmitter will rapidly fl ash for a minute. If it doesn’t fl ash try again.
•
While the red light on the Transmitter is fl ashing, press and hold the Down button on
the Monitor until the LED on the Monitor fl ashes.
•
When you release the button the screen will show an icon indicating information is
being received from the transmitter, shown in Figure 3.
•
Once the tuning is complete your display should show ‘0 watts’.
Fitting the Sensor Jaw and Transmitter to the Cable
•
Take the Sensor and Transmitter to your mains meter.
•
Identify the thick round cable
that leads from the meter to your
house, usually 4th from the left.
•
Ensure there is room around
the cable then clamp the Sensor
around the cable, as shown.
•
If you have concerns about
any aspect of the safety of your
meter and installing the Real
Time Electricity Monitor please contact a quali fi ed electrician.
Welcome to your Real Time Electricity Monitor that will help you understand more
about the electricity you use, and the small steps you can take to cut wasted energy.
By sending a wireless signal to your Monitor from a Transmitter linked to your meter,
you can see the e ect in real time of switching appliances and lighting on and o by
displaying total electricity consumption in terms of cost and energy savings. This will
help you save energy, money and the environment.
It is quick and easy to install and has been designed with safety as a priority.
Safely using your Real Time Electricity Monitor
It is important to observe some simple precautions before using this produc t.
Please follow closely the instructions to set up your Monitor:
•
Do not proceed if you have any doubt about how to safely install it yourself.
•
If you notice anything unusual about your electricity meter and c abling, such
as loose wires, exposed cabling, burn marks or holes in the insulating materials
or damage to your meter, do not install the products.
If you have concerns about any aspect of the safety of your meter and installing the
Real Time Electricity Monitor, please contact a qualifi ed electrician.
In addition, the following safety precautions should be observed. Do not:
•
Attempt to repair or service any part of the Real Time Electricity Monitor.
•
Expose or immerse the product in water, or any other liquid.
•
Expose the product to heat, fl ame, steamy conditions or extreme cold.
•
Open the equipment or touch any of its electronic circuitry.
•
Hit, strike or drop the equipment.
•
If the display gets broken, please don’t touch the liquid crystals.
•
Use this product for any purpose other than for which it was intended.
Getting Started
Check you have got everything
1. Sensor and Transmitter
2. Monitor
3. Power Supply
Understanding your Real Time
Electricity Monitor Display
1. The lightning bolt indicates the number of Sensors installed. For most
domestic situations this is 1. For more information see Additional
Accessories.
2. Icon indicates information is being received from transmit ter.
3. Shows real time electricity usage.
4. Shows rough cost of electricity you are using now. It will change as
you switch electrical appliances on and off (this rotate s between daily
and monthly).
5. Shows the increase or decrease in running costs when appliances are
switched on/off.
6. This graph shows how much energy has been used in previous periods.
Night = 11pm-7am previous night, Day = 7am-3pm previous day and
Evening = 3pm-11pm previous evening.
7. This shows cumulative energy consumption in kWh and scrolls every ten
seconds between previous day, previous seven days and last 30 days.
You can also scroll through these using the Centre button.
1 32
Down
Do
w
n
p
DAY
ELECTRIC
C
1
2
3
4
5
6
7
1
2
3
Meter
Figure 1.
Up Button
Centre Button
Down Button
Light
Trans mit ter
Monitor
Tuning Push Switch
Sensor Light
Figure 2.
Figure 3.
Loading...