British Gas RD1 User Manual

Page 1
USERS
GUIDE
Householders guide to domestic central heating boilers
British/Scottish
Gas RD1
the wall hung boiler
Wall hung, gas fired
30 - 100 RD1
Page 2
2
British Gas RD1- User's
British Gas RD1 (Natural Gas Models Only)
Introduction
It is essential that the instructions in this booklet are strictly followed, for safe and economic operation of the boiler.
Current Gas Safety (Installation & Use) Regulations or the rules in force.
In your own interest, and that of safety, it is the law that this boiler must be installed by a registered installer, in accordance with all national and local regulations.
Electricity Supply
This appliance must be efficiently earthed.
Supply: 230 V ~ 50 Hz. The fusing should be 3A.
Connection must be made in a way that allows complete isolation of the electrical supply such as a double pole switch having a 3mm (1/8") contact separation in both poles, or a plug and socket, serving only the boiler and system controls. The means of isolation must be accessible to the user after installation.
30 RD1 G.C. No. 41 349 77 40 RD1 G.C. No. 41 349 76 50 RD1 G.C. No. 41 349 75 60 RD1 G.C. No. 41 349 74 70 RD1 G.C. No. 41 349 73 80 RD1 G.C. No. 41 349 72
100 RD1 G.C. No. 41 387 52
British Gas:
(Any internal reference to British Gas applies equally to Scottish Gas)
The British Gas RD1 is a range of cast iron wall mounted fanned flue gas central heating boilers. A complete range of natural gas models is available.
The ideal replacement boiler...
Easy to install, easy to operate and easy to service. The British Gas RD1 really is the ultimate replacement wall mounted range - you can depend on it.
Proven reliability...
Proven cast iron heat exchanger engineered and refined to be the most dependable wall mounted boiler ensuring totally calm operation and quiet running, whatever the system demands.
Complete range...
There are 7 models in the range. All models include a Downward Routing Pipe Kit and an overheat thermostat.
Full system suitability...
Most models are suitable for connection to pumped open vent central heating systems, pumped central heating combined with pumped or gravity indirect domestic hot water supply systems (note that the 100 model is not suitable for gravity installations). They can also be used on sealed water systems.
Free Three Star Service Cover:
In addition to the guarantee, we will provide absolutely free a British Gas Services Three Star Service Cover agreement to cover your complete new system during the first year. The benefits of this cover include priority attention and a 24 hours a day 365 day a year helpline. Full details of the terms and conditions for Three Star Cover schemes are available separately on request.
THE LOG BOOK SHOULD BE COMPLETED AFTER
EACH SERVICE AND KEPT WITH THESE
INSTRUCTIONS
All CORGI Registered Installers carry a CORGI ID card, and have a registration number. Both should be recorded in your Benchmark Log Book. You can check your installer by calling CORGI direct on 0156 372 300.
Page 3
3
British Gas RD1- User's
CAUTION.
To avoid the possibility of injury during the installation, servicing or cleaning of
this appliance care should be taken when handling edges of sheet steel components
To light the boiler.
Refer to Frame 1
1. CHECK THAT THE ELECTRICITY SUPPLY TO THE BOILER
IS OFF.
2. Open the controls access door by hinging downwards.
3. Ensure that the gas service cock (D) is OPEN.
4. Press the overheat reset button (E), located as shown in
Frame 1.
5. Ensure that the thermostat on/off knob (B) is in the OFF position.
6. Switch ON the electricity supply to the boiler. Check that all external controls, e.g.programmer, room thermostat etc., are ON.
7. Set the boiler thermostat On/Off knob (B) to position 6. After about 25 seconds the boiler will light automatically - this can be viewed through the sight glass (A). Set the boiler thermostat to the desired position.
8. Close the controls access door.
Note.
If the boiler fails to light after 5 attempts press the reset switch (C) and the ignition sequence will be repeated. If the boiler still fails to light consult a CORGI registered installer.
In winter conditions, i.e. central heating and domestic hot water, the thermostat should be set at position 5 or 6.
For summer conditions, i.e. domestic hot water only, the thermostat should be set at position 3.
These settings, however, are offered for general guidance only and other settings may be found preferable, dependent upon the type of system installed or as recommended by the installer.
1
BOILER CONTROLS
LEGEND
A. Sightglass.
B. Thermostat On/Off knob.
C. Boiler reset switch.
View inside boiler controls area
D. Gas service cock (shown
in the OPEN position).
E. Overheat thermostat
reset button.
Table 1
Above the boiler 100 mm (4")
At each side of the boiler 5 mm (1/4")
Underneath the boiler 100 mm (4")
In front of the boiler 75 mm (3 ")
Controls door
C
L
1
0
3
7
-
4
Remote appliance diagnostic system
This appliance is capable of automatically communicating operational data to a central computer processing system via the house ring main and telephone line, known as 'Remote Appliance Diagnostic System' (RADS). The information is transmitted in the early hours of the morning once every 30 days, or immediately if the boiler develops a fault. If an attempt is made to use the telephone during the transmission, some interference will be heard. In this event replace the receiver and try again after 30 seconds.
Important points
a. This appliance must not be operated without the casing
correctly fitted and forming an adequate seal.
b. If the boiler is installed in a compartment then the
compartment MUST NOT be used for storage purposes.
c. The ventilation provided for the boiler during installation
MUST NOT be blocked, and a check should be made periodically that the ventilation areas are free from any obstruction.
d. If it is known or suspected that a fault exists on the boiler
then it MUST NOT be used until the fault has been corrected by a CORGI registered installer.
e. Flammable materials must not be placed in close proximity to
the appliance. Materials giving off flammable vapours must not be stored in the same room as the appliance.
f. Under NO circumstances should any of the sealed
components on this appliance be used incorrectly or tampered with.
In cases of repeated or continuous shutdown a CORGI registered installer should be called to investigate and rectify the
condition causing this and carry out an operational test after each intervention on the device. Only the manufacturer's original parts should be used for replacement.
Minimum clearances
A clearance of 533mm (21") MUST be available at the front of the boiler for servicing. The minimum clearances given below MUST be complied with in order to maintain the safe running of the boiler. Refer to Table 1.
Page 4
April 2001 UIN 154 271A03
The code of practice for the installation,
commissioning & servicing of central heating systems
British Gas Services Limited is a member of the Benchmark
initiative and fully supports the aims of the programme.
Benchmark has been introduced to improve the standards of
installation and commissioning of central heating systems in
the UK and to encourage the regular servicing of all central
heating systems to ensure safety and efficiency.
THIS SYMBOL IS YOUR ASSURANCE OF QUALITY
These appliances are designed for use with Natural Gas only. They have been tested and conform with the provisions of BS. 6332 and BS. 5258.
CERTIFIED PRODUCT Manufactured under a BS EN ISO 9001:1994 Quality System accepted by BSI.
British Gas pursues a policy of continuing improvement in the design and performance of its products. The right is therefore reserved to vary specification without notice.
British Gas Services Limited. Registered in England No. 3141243. Registered Office: Charter Court 50 Windsor Road, Slough, Berkshire SL1 2HA. British Gas Services Ltd. has made every effort to ensure that the information contained in this leaflet is accurate. However, not all the information is within the control of British Gas Services Ltd., and it may have changed since publication. British Gas Services Ltd. does not accept any liability for changes which occur after publication. No guarantee takes away any rights you may have at law. Calls to this number may be monitored to maintain a high level of service and for training purposes.
Priority Helpline 08459 500 400
This boiler is exclusively manufactured for British Gas by Ideal Boilers Ltd.
Control of water temperature
1. Adjust the boiler thermostat (B) to give the required temperature for central heating.
2. The boiler thermostat automatically switches the main burner
OFF and ON to maintain the selected temperature.
To shut down the boiler
1. For short periods
Set the boiler On/Off knob (B) to OFF. When heating is again required, turn the knob to the desired position.
2. For longer periods
Set the boiler On/Off knob (B) to OFF. Switch OFF the electricity supply.
To relight the boiler
Repeat the procedure 1 - 8, detailed in 'To light the boiler'.
Frost protection
If no frost protection is provided and frost is likely during a short absence from home, leave the heating controls at a reduced temperature setting. For longer periods, the entire system should be drained ­including the domestic water supply. If the system includes a frost thermostat then, during cold weather, the boiler should be
turned OFF at the time switch(es) ONLY. The mains supply should be left switched ON, with the boiler thermostat left in the normal running position.
Boiler Overheat Thermostat
The boiler is fitted with a safety 'cutout' thermostat. This will shut down the boiler in the event of overheating. Should this occur allow the boiler to cool, press the reset button (E) then relight as detailed in steps 1-8 in 'To light the boiler'.
If the cutout condition still persists turn off the boiler and consult a CORGI registered installer.
Loss of system water pressure
Boilers fitted with Sealed System Units only
If the red arrow on the unit pressure gauge is set above zero and the system pressure is seen to fall below this value over a period of time then a water leak is indicated. In this event a CORGI registered installer should be consulted. DO NOT OPERATE THE BOILER IF THE PRESSURE HAS
REDUCED TO ZERO FROM THE ORIGINAL SETTING.
Escape of gas
Should a gas leak be suspected, contact your local gas supplier without delay.
Do NOT search for gas leaks with a naked flame.
Cleaning
For normal cleaning simply dust with a dry cloth. To remove stubborn marks and stains, wipe with a damp cloth and finish off with a dry cloth.
Do NOT use abrasive cleaning materials.
Maintenance
The appliance should be serviced at least once a year by a CORGI registered installer.
Approximate flow temperatures for the boiler thermostat settings are:
Knob Setting Flow Temperature
°C °F
1 54 130
2 60 140
3 66 150
4 71 160
5 77 170
6 82 180
Loading...