Briteq LED Blaster 108 User Manual

USER

MANUAL

Ver 1,0

WWW.BRITEQ-LIGHTING.COM

1.1 PRODUCT INTRODUCTION

This product is designed for indoor or outdoor use. Suitable applications include wash or effect lighting for architectural, stage or nightclub applications. This product can also be installed for use in signage and advertising using the dynamic functions available with DMX512 control. Direct input of DMX512 signal allows the units to be controlled from any DMX512 controller. This product can be operated as a single unit or in multiple units for large applications.

The specially developed controller that allows the product to be controlled independent of the DMX512 controller enables the user to create and edit a wide range of custom programs. All programs can be touch-button displayed or scheduled to START and END at scheduled times. When programs have been created or edited in the controller, it is also possible to trigger these programs using the DMX IN function when connected to a DMX512 controller.

1.2 PRODUCT FEATURES

LED FIXTURE

1 PRODUCT(GENERAL)

1

2008.8.13

1 PRODUCT (GENERAL)

* RGB Dimmer 0-100% * Strobe * Individual control of each LED group * Automatic programs * IP65 protection rating * LCD display * Display control 'lock-out' * Direct DMX512 input * Automatic DMX512 and ID Addressing * Independant ID address * Overheat protection (showing "warning heat") * Lightweight aluminium casing * Black anti-UV plastic cover * Interlocking-module system

1.3 TECHNICAL SPECIFICATIONS

LED MODULE

1 PRODUCT(GENERAL)

2

2008.8.13

Dimensions

LED MODULE:

Voltage

Rated Power

IP65 protection rating

108pcs (36 x RED / 36 x GREEN / 36 x BLUE)

Weight

LED/Unit

Output/LED

Cooling

IP

1W

Direct air convection

570 x 220 x 190mm

13Kg

100~240V...50/60Hz

150W

1.4 PHOTOMETRIC DATA

PHOTOMETRIC DATA

1 PRODUCT(GENERAL)

3

2008.8.13

RGB 100%

1 2 3

0

1

2

3

2(0.9x0.5)

4(1.4x1.0)

6(2.0x1.6) 8(2.5x2.1)

10(3.0x2.6Area(m)) Diameter(m)

9100

2910 1370 800 643 LUX

15

WHITE

1 2 3

0

1

2

3

2(0.9x0.5)

4(1.4x1.0)

6(2.0x1.6) 8(2.5x2.1)

10(3.0x2.6Area(m)) Diameter(m)

8100

2570 1160 689 575 LUX

15

RED

1 2 3

0

1

2

3

2(0.9x0.5)

4(1.4x1.0)

6(2.0x1.6) 8(2.5x2.1)

10(3.0x2.6Area(m)) Diameter(m)

2900

893 414 238 197 LUX

15

GREEN

1 2 3

0

1

2

3

2(0.9x0.5)

4(1.4x1.0)

6(2.0x1.6) 8(2.5x2.1)

10(3.0x2.6Area(m)) Diameter(m)

5565

1752 836 471 396 LUX

15

BLUE

1 2 3

0

1

2

3

2(0.9x0.5)

4(1.4x1.0)

6(2.0x1.6) 8(2.5x2.1)

10(3.0x2.6Area(m)) Diameter(m)

710

231 110 64 53 LUX

15

1.5 SAFETY WARNING

IMPORTANT

ALWAYS READ THE USER MANUAL BEFORE OPERATION.

PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA.

This product must be installed by a qualified professional. Always operate the equipment as described in the user manual.

A minimum distance of 0.5m must be maintained between the equipment and

combustible surface.

The product must always be placed in a well ventilated area.

Always make sure that the equipment is installed securely.

DO NOT stand close to the equipment and stare directly into the LED light

source.

Always disconnect the power supply before attempting and maintenance.

Always make sure that the supporting structure is solid and can support the

combined weight of the products. The earth wire must always be connected to the ground. Do not touch the power cables if your hands are wet.

ATTENTION

1 PRODUCT(GENERAL)

4

This product left the place of manufacture in perfect condition. In order to maintain this condition and for safe operation, the user must always follow the instructions and safety warnings described in this user manual. Avoid shaking or strong impacts to any part of the equipment. Make sure that all parts of the equipment are kept clean and free of dust. Always make sure that the power connections are connected correct and

secure.

If there is any malfunction of the equipment, contact your distributor

immediately.

When transferring the product, it is advisable to use the original packaging in

which the product left the factory.

Shields, lenses or ultraviolet screens shall be changed if they have become

damaged to such an extent that their effectiveness is impaired.

The lamp (LED) shall be changed if it has become damaged or thermally

deformed.

2008.8.13

2 INSTALLATION

5

2008.8.13

2.1 MOUNTING

The LED MODULE can be mounted in a hanging position using the support frame. It is possible to use any bolt of the correct size and strength to mount the fixture. It is recommended to use at least 2 mounting points per fixture. Mounting with a clamp or other mounting bracket is recommended depending on the requirements of your application. For overhead use, always install a securechain that can hold at least 10 times the weight of the fixture. You must only use safety-ropes with screw-on carabines. Pull the safety-rope through the aperture on the the base's metal frame. Insert the end in the carabine and tighten the fixation screw. (See picture on right)

HANGING

UPRIGHT

The LED MODULE can be mounted upright using the support frame. It is possible to use any bolt of the correct size and strength to mount the fixture. It is recommended to use at least 2 mounting points per fixture. Mounting with a clamp or other mounting bracket is recommended depending on the requirements of your application.

The LED MODULE can be mounted at any angle and in any position. It is possible to further adjust the angle of the LED MODULE using the two adjustment knobs located on the side of the fixture.

2.2 POWER CONNECTIONS

2 INSTALLATION

UPRIGHT

@ 220~240V: 15 units may be connected in series

@100~120V: 8 units may be connected in series

2 INSTALLATION

6

2008.8.13

2.3 INTERLOCKING MULTIPLE FIXTURES

The diagram above shows how multiple units can be interlocked together to create a 'panel' or 'blinder' arrangement.

The 'male' and 'female' connections enable the fixtures to be interlocked together in the way shown in the diagram. Please note that when multiple units are mounted together it is not necessary to attach every single unit to the truss, wall or weight supporting system. However, it is important to ensure that all fixtures are securely locked together and that each fixture is secured using a safety cable.

2 INSTALLATION

7

2008.8.13

2.4 SETTING UP WITH A DMX512 CONTROLLER

2.4-1 DMX512 ADDRESSING WITHOUT ID ADDRESSING (STAGE 1 MODE)

The figure above shows a simple DMX512 layout with the starting address of the first unit set at 1, with the second set at 13 and so on... (Note that when used in this way, the CH10 ID function must be inactive (CH10=0))

............

DMX512 CONTROLLER

DMX Addr.1

DMX Addr.13 DMX Addr.25

Connect the DMX512 controller to the units in series. Each unit has 12 DMX channels so the DMX Addresses should increase by increments of

12 (e.g. 1,13,25,37...)

The ID address has not been set so therefore when using the controller CH10 must

be inactive ( CH10=0 ).

It is also possible to deactivate ID address selecting ID OFF from the Settings menu.

on the fixture

Each DMX Address may be used as many times as required. Any DMX address in the range from 001 to 245 may be used.

2.4-2 DMX512 ADDRESSING WITH ID ADDRESS(STAGE 1 MODE)

Connect the DMX512 controller to the units in series Each unit has 12 DMX channels so the DMX Addresses should increase by increments of

12 (e.g. 1,13,25,37...)

Each DMX Address may be used as many times as required. Any DMX address in the range from 001 to 245 may be used. Each DMX address may carry up to 66 separate ID addresses.

ID Address should be set in the Settings menu on each unit in ascending values

(i.e. 1,2,3...)

ID On should be set in the Settings menu on each unit.

ID addresses are accessible from CH10 on the DMX512 controller.

Example:

............

DMX512 CONTROLLER

DMX Addr.1

ID Addr.1

DMX Addr.1 ID Addr.2

DMX Addr.1 ID Addr.3

DMX Addr.13 ID Addr.1

DMX Addr.13 ID Addr.2

DMX Addr.13 ID Addr.3

Example:

The figure above shows a simple DMX layout which has used three units at each DMX address. The three units have different ID addresses which allows the user to collectively control the whole group of units at that DMX address by setting CH10 to 0, or to control each unit independently by first selecting the DMX address and then by using CH10 to locate the target ID address. (Note that when using ID addresses it is also possible to activate ADAS which allows for even more options with DMX addressing and control see ADAS Addressing section 2.2-3)

2.4-3 ADAS WITH ID ADDRESS(STAGE 1 MODE)

Connect the DMX512 controller to the units in series Select ADAS ON from the Settings menu

ID Address should be set in the Settings menu on each unit

in ascending values (i.e. 1,2,3...)

ADAS addressing is based on the ID address as follows:

ADAS DMX Address = { ADAS fader * (ID Address -1)}+ 1

ADAS addressing is activated by moving CH8 + CH10 faders to the 255 value (CH8 = 255 &

CH10 = 255)

ADAS addressing is deactivated by moving CH8 + CH10 + CH11 to the 255 value

(CH8 = 255, CH10 = 255 & CH11 = 255)

When ADAS is deactivated, all DMX addresses will return to their original DMX Address. To permanently store ADAS DMX addresses, select ADAS copy from the Settings

menu,on the target fixtures to store the new DMX Address.

Example:

............

DMX512 CONTROLLER

ID Addr.1 ID Addr.2 ID Addr.3

The figure above shows a simple ID address layout using one DMX address. Each of the units has a different ID address which will receive a new temporary DMX address when ADAS is activated (unless ADAS copy is selected). The user is able to activate and deactivate ADAS at will giving the possibility of creating many different fixture grouping possibilities using the ID address, real DMX address and the ADAS temporary DMX address.

2 INSTALLATION

2008.8.13

When using ADAS, all fixtures must have the

following settings from the Settings menu set correctly;

ID address Each unit should have the target ID address set in ascending order ID ON/OFF Each unit should set ID On ADAS fader no Each unit should be set to the same number of faders as your

controller(must be 12)

ADAS ON/OFF Each unit should be set as ADAS On

Note:

8

3.1 BASIC

The LED fixture is mounted with a LCD display and 4 control buttons.

UP DOWN EXIT

SET

enter the currently selected menu or confirm the current function value

scroll 'UP' through the menu list or increase the value of the current function

scroll 'DOWN' through the menu list or decrease the value of the current function

exit from the current menu or function

3 DISPLAY PANEL OPERATION

2008.8.13

3 DISPLAY PANEL OPERATION

9

3.2 MENU

3 DISPLAY PANEL OPERATION

10

2008.8.13

Auto program

Auto 1

Auto 2

Auto 3

Auto 4

Auto 5

Auto 6

Auto 7

Auto 8

MENU

Static color

Red

Green

Blue

Color macros

Strobe

Dimmer

Red

Green

Blue

Color macros

Strobe

DMX512

Password

Password ON/OFF

Set password

Password

ON/OFF

Set Password

Dimmer

0 255

Address

Address 1

512

0 255

Settings

ID address

ID ON/OFF

ADAS fader no

ADAS ON/OFF

ADAS copy

Reset to

Factory settings

ON/OFF

ID

ON/OFF

ADAS

ON/OFF

ADAS copy

Reset confirm

01 244

ADAS fader no

ID address

001 066

Run mode

DMX CON

Dimmer start

001 / 005

Personality

STAGE 1

STAGE 2

ARC 1

ARC 1+D

PIXEL

MENU

Static color

Red

Green

Blue

Color macros

Strobe

Dimmer

Red

Green

Blue

Color macros

Strobe

Dimmer

0 255

3.3 CREATING A STATIC COLOR

Static colour

Combine RED, GREEN and BLUE to create an infinite range of colors (0-255) Enter Color macros allow to choose 18 color macros Set value of dimmer (0-255) Set the value of the strobe (0-20Hz)

3.4 DMX512 SETTINGS

DMX512 address

Enter the DMX address mode to set the DMX address Activate control from outside source by activating ON

3 DISPLAY PANEL OPERATION

11

DMX512

Address 1 512

MENU

2008.8.13

3.5 DMX CHANNEL MODE

Personality

Enter Personality mode to choose DMX mode: STAGE 1 , STAGE 2 ,

PIXEL , ARC 1 or ARC 1+D .

3.6 RUN MODE

Run mode

DMX CON

MENU

Personality

STAGE 1

STAGE 2

ARC 1

ARC 1+D

PIXEL

Run mode

Enter the Run mode mode to set the working mode

DMX mode is for using the DMX512 controller to control the fixtures.

CON mode is for using the pix controller to control the fixtures.

3.7 ACTIVATING AN AUTO PROGRAM

Auto Program

Select the target Auto mode and press Set to display

MENU

Auto program

Auto 1

Auto 2

Auto 3

Auto 4

Auto 5

Auto 6

Auto 7

Auto 8

3 DISPLAY PANEL OPERATION

12

3.8 CHANGING THE SETTINGS

Settings

Enter the ID Address to set the ID address for the unit Enter ID ON/OFF in order to allow/disallow ID address function from the

DMX512 controller

Enter the ADAS fader no to set the number of channel faders in each layer

of the controller

In ADAS ON/OFF select allow/disallow Automatic DMX512 Addressing

System (ADAS)

In the ADAS COPY menu select whether to allow copy of DMX address to unit after ADAS has assigned new DMX address when ADAS function is activated from the DMX512 controller.

Enter the Reset to Factory Settings in order to reset to default factory settings.

Enter the Dimmer start to select dimmer start value 001 or 005 . The default setting is 005 .

2008.8.13

Settings

ID address

ID ON/OFF

ADAS fader no

ADAS ON/OFF

ADAS copy

Reset to

Factory settings

ON/OFF

ID

ON/OFF

ADAS

ON/OFF

ADAS copy

Reset confirm

01 244

ADAS fader no

ID address

001 066

Dimmer start

001 / 005

MENU

3.9 A CTIVATE THE PASSWORD

3.10 POWER ON/OFF

MENU

Password

ON/OFF

Password

Set Password

Enter the Password mode to set password YES/NO

When password is activated, display will demand password each time

the fixture is powered on.

Enter the Set password menu to change password. Set new password using the UP & DOWN keys. Input an 8 digit password and then press SET to confirm NOTE: In the event that the password is forgotten. Please use the factory password shown below.

UP > DOWN >UP > DOWN > UP > UP > DOWN > DOWN

TURN OFF When display shows MENU , hold down the EXIT key

for 3 seconds to turn off power.

TURN ON When display is off, hold down the EXIT key for 3 seconds to turn on power.

3 DISPLAY PANEL OPERATION

13

2008.8.13

4.1 BASIC ADDRESSING

Connect all of the units in series using standard DMX512 signal cable or the IP65 rated cable

provided. Set the DMX512 address in the 'DMX512 Address' menu. It is possible to have the same DMX address or independent addresses for each fixture.

4.2 CHANNEL ASSIGNMENT

Note:

This product has four DMX512 channel configurations (STAGE 1 , STAGE 2 ,PIXEL,

ARC 1 & ARC 1+D).

Both STAGE 1 and STAGE 2 have two DMX modse: DMX MODE 1 and DMX

MODE 2

Ch9 is used to switch from one DMX MODE 1 (0-244) to DMX MODE 2 (245-255).

4 USING A DMX512 CONTROLLER

ARC 1

CHANNEL VALUE

0 4

1

RED

No function

0-100%

5 255

0 4

2

GREEN

No function

0-100%

5 255

0 4

3

BLUE

No function

0-100%

5 255

FUNCTION

14

ARC 1+D

0 4

4

BLUE

No function

0-100%

5 255

CHANNEL VALUE

0 4

1

DIMMER

No function

0-100%

5 255

0 4

2

RED

No function

0-100%

5 255

0 4

3

GREEN

No function

0-100%

5 255

FUNCTION

2008.8.13

4 USING A DMX512 CONTROLLER

STAGE 1(DMX MODE 1)

4 USING A DMX512 CONTROLLER

0 4

5

CYAN

No function

0-100%

5 255

0 4

4

YELLOW

No function

0-100%

5 255

CHANNEL VALUE

0 4

1

RED

No function

0-100%

5 255

0 4

2

GREEN

No function

0-100%

5 255

0 4

3

BLUE

No function

0-100%

5 255

0 4

6

PURPLE

No function

0-100%

5 255

0 4

7

WHITE

No function

0-100%

5 255

0 4

8

STROBE

No function

Strobe (slow to fast)

5 255

FUNCTION

MODE SELECTION

0 4

No function

5 34

Color-Cycle Mode 1

35 64

Color-Cycle Mode 2

65 94

Color-Cycle Mode 3

95 124

Color-Cycle Mode 4 (speed can be adjusted using Channel 11)

125 154

Color-Cycle Mode 5

155 184

Color-Cycle Mode 6

185 214

Color-Cycle Mode 7

215 244

Color-Cycle Mode 8

245 255

DMX MODE 2

9

15

2008.8.13

CHANNEL VALUE FUNCTION

EFFECT MACRO

0

5

10

250

4

9

14

255

No function

Effect MACRO #1

. . . . . .

Effect MACRO #2 . . . . . .

Effect MACRO #50

12

MODULE SELECTION

0 4

#1 ON #2 ON #3 ON

5 34

#1 ON

35 64

#2 ON

65 94

#3 ON

95 124

#1 ON #2 ON

125 154

#2 ON #3 ON

155 184

#1 ON #3 ON

185 214

#1 ON #2 ON #3 ON

215 255

#1 OFF #2 OFF #3 OFF

Speed control of CH9 Color-Cycle Mode 4

11

0 255

ID ADDRESS SELECTION (also see pg. 26)

0 9

Select all ID addresses

ID address #1

10

10 19

20

30

200

29

39

209

. . . . . .

210

211

212

. . . . . .

255

ID address #2

ID address #3

ID address #20

ID address #21

ID address #22

ID address #23

ID address #66

4 USING A DMX512 CONTROLLER

16

2008.8.13

9

0 244

245 255

MODE SELECTION

DMX MODE 1

DMX MODE 2

CHANNEL VALUE FUNCTION

MODULE #1

0 4

No function

5 34

RED

35 64

GREEN

65 94

BLUE

95 124

YELLOW

125 154

CYAN

155 184

PURPLE

185 255

PINK-WHITE

1

MODULE #2

0 4

No function

5 34

RED

35 64

GREEN

65 94

BLUE

95 124

YELLOW

125 154

CYAN

155 184

PURPLE

185 214

PINK-WHITE

2

MODULE #3

0 4

No function

5 34

RED

35 64

GREEN

65 94

BLUE

95 124

YELLOW

125 154

CYAN

155 184

PURPLE

185 214

PINK-WHITE

3

4

NO FUNCTION

5

6

7

8

0 4

5 255

STROBE

No function

Strobe (slow to fast)

4 USING A DMX512 CONTROLLER

STAGE 1(DMX MODE 2)

17

2008.8.13

ID ADDRESS SELECTION (also see pg. 26)

0 9

Select all ID addresses

ID address #1

10

10 19

20

30

200

29

39

209

. . . . . .

210

211

212

. . . . . .

255

ID address #2

ID address #3

ID address #20

ID address #21

ID address #22

ID address #23

ID address #66

CHANNEL VALUE FUNCTION

11

12

NO FUNCTION

4 USING A DMX512 CONTROLLER

18

2008.8.13

STAGE 2(DMX MODE 1)

0 9

5

COLOR MACROS

No function

RED (100%)

RED+GREEN (R85%+G15%)

RED+GREEN (R60%+G40%)

YELLOW (100%)

RED+GREEN (R15%+G85%)

RED+GREEN (R40%+G60%)

GREEN (100%)

GREEN+BLUE (G85%+B15%)

GREEN+BLUE (G60%+B40%)

BLUE (100%)

BLUE+GREEN (G85%+B15%)

BLUE+GREEN (G60%+B40%)

CYAN (100%)

GREEN+PURPLE (G50%+P50%)

PURPLE (100%)

PURPLE+GREEN (P80%+G20%)

RGB (100%)

WHITE (100%)

10 29

0 4

4

BLUE

No function

0-100%

5 255

CHANNEL VALUE

0 4

1

DIMMER

No function

0-100%

5 255

0 4

2

RED

No function

0-100%

5 255

0 4

3

GREEN

No function

0-100%

5 255

FUNCTION

30

40

50

70

80

90

110

120

130

39

49

69

79

89

109

119

129

149

150 159

160 169

170

190

200

220

230

250

189

199

219

229

249

255

0 4

6

STROBE

No function

Strobe (slow to fast)

5 255

4 USING A DMX512 CONTROLLER

19

2008.8.13

CHANNEL VALUE FUNCTION

MODE SELECTION

0 4

No function

5 34

Color-Cycle Mode 1

35 64

Color-Cycle Mode 2

65 94

Color-Cycle Mode 3

95 124

Color-Cycle Mode 4 (speed can be adjusted using Channel 11)

125 154

Color-Cycle Mode 5

155 184

Color-Cycle Mode 6

185 214

Color-Cycle Mode 7

215 244

Color-Cycle Mode 8

245 255

DMX MODE 2

7

EFFECT MACRO

0

5

10

250

4

9

14

255

No function

Effect MACRO #1

. . . . . .

Effect MACRO #2 . . . . . .

Effect MACRO #50

10

MODULE SELECTION

0 4

#1 ON #2 ON #3 ON

5 34

#1 ON

35 64

#2 ON

65 94

#3 ON

95 124

#1 ON #2 ON

125 154

#2 ON #3 ON

155 184

#1 ON #3 ON

185 214

#1 ON #2 ON #3 ON

215 255

#1 OFF #2 OFF #3 OFF

Speed control of Ch7 Color-Cycle Mode 4

9

0 255

ID ADDRESS SELECTION (also see pg. 26)

0 9

Select all ID addresses

ID address #1

8

10 19

20

30

200

29

39

209

. . . . . .

210

211

212

. . . . . .

255

ID address #2

ID address #3

ID address #20

ID address #21

ID address #22

ID address #23

ID address #66

4 USING A DMX512 CONTROLLER

20

2008.8.13

7

0 244

245 255

MODE SELECTION

DMX MODE 1

DMX MODE 2

CHANNEL VALUE FUNCTION

MODULE #1

0 4

No function

5 34

RED

35 64

GREEN

65 94

BLUE

95 124

YELLOW

125 154

CYAN

155 184

PURPLE

185 255

PINK-WHITE

1

MODULE #2

0 4

No function

5 34

RED

35 64

GREEN

65 94

BLUE

95 124

YELLOW

125 154

CYAN

155 184

PURPLE

185 214

PINK-WHITE

2

MODULE #3

0 4

No function

5 34

RED

35 64

GREEN

65 94

BLUE

95 124

YELLOW

125 154

CYAN

155 184

PURPLE

185 214

PINK-WHITE

3

4

NO FUNCTION

5

6

0 4

5 255

STROBE

No function

Strobe (slow to fast)

4 USING A DMX512 CONTROLLER

STAGE 2(DMX MODE 2)

21

2008.8.13

ID ADDRESS SELECTION (also see pg. 26)

0 9

Select all ID addresses

ID address #1

8

10 19

20

30

200

29

39

209

. . . . . .

210

211

212

. . . . . .

255

ID address #2

ID address #3

ID address #20

ID address #21

ID address #22

ID address #23

ID address #66

CHANNEL VALUE FUNCTION

9

10

NO FUNCTION

4 USING A DMX512 CONTROLLER

22

2008.8.13

PIXEL

1

2

5 255

CHANNEL FUNCTIONVALUE

3

4

5

6

7

8

9

5 255

BLOCK1-RED

BLOCK1-GREEN

BLOCK1-BLUE

BLOCK2-RED

BLOCK2-GREEN

BLOCK2-BLUE

BLOCK3-RED

BLOCK3-GREEN

BLOCK3-BLUE

1~9

0 4

NO FUNCTION

4.3 BASIC INSTRUCTIONS FOR DMX512 OPERATION

STAGE 1 DMX MODE 1

RED, GREEN & BLUE COLOR SELECTION

CH1, CH2 & CH3 control the intensity ratio of each of the RED, GREEN & BLUE LEDs. When the slider is at the highest position (255) the intensity of the color is the

maximum.

CH1, CH2 & CH3 can be combined together to create over 16 million colors. CH1, CH2, CH3 have priority over CH4, CH5, CH6 & CH7

YELLOW, CYAN, PURPLE & WHITE

CH4, CH5, CH6 & CH7 are independent colors and cannot be mixed with any other

color control channel.

When multiple channels are used at the same time;lower channel number is priority

(i.e. CH4 has priority over all channels 1-6)

STROBE

CH8 is the strobe channel and controls the strobe effects of CH1, CH2, CH3, Ch4,

CH5, CH6, & CH7

The strobe is with an adjustable speed with a maximum of 20Hz. The strobe is not active with CH9 & CH12

MODE SELECTION

CH9 allows the user to activate DMX MODE 1 (0-244) or DMX MODE 2 (245-255).

CH9 values 5-244 can only be activated when CH1 to CH7 are not

activated

When Color-Cycle Mode 4 is selected CH11 controls the speed of the Color-cycle.

ID ADDRESS SELECTION

CH10 is used to select the target ID address. Each independent DMX address may have upto 66 independent ID addresses. An ID address of 0 will be activated by all ID address locations.

MODULE SELECTION

CH11 controls set combinations of the three LED MODULES present in each unit. CH11 has priority over CH12 when first activated

EFFECT MACRO

The effect MACRO channel allows the user to select from combinations of different

colors and LED modules in a quick-and-easy action.

CH12 has priority over color control channels (CH1, CH2, CH3, CH4, CH5, CH6 &

CH7)

CH12 has priority over CH11 when first activated CH12 has priority over Ch9 & Ch11

4 USING A DMX512 CONTROLLER

23

2008.8.13

STAGE 1 DMX MODE 2

MODULE #1, MODULE #2 & MODULE #3 SELECTION

CH1, CH2 & CH3 allow quick-and-simple control of the three LED MODULEs Control of the LED MODULEs can be used in conjunction with all other channels in

DMX MODE 2

STROBE

CH8 is the strobe channel and controls the strobe effects of CH1, CH2 & Ch3 The strobe is with an adjustable speed with a maximum of 20Hz.

MODE SELECTION

CH9 allows the user to activate DMX MODE 1 (0-244) or DMX MODE 2 (245-255).

ID ADDRESS SELECTION

CH10 is used to select the target ID address. Each independent DMX address may have up to 66 independent ID addresses.

4 USING A DMX512 CONTROLLER

24

2008.8.13

STAGE 2 DMX MODE 1

DIMMER

CH1 control the dimmer intensity of Ch2, Ch3, Ch4, Ch5, Ch6 & Ch9. When Ch1is set to 0 , Ch2, Ch3, Ch4, Ch5, Ch6 & Ch9 no funtion.. When the slider is at the highest position (255) the dimmer intensity is the maximum. CH1 has priority over Ch7 when first activated.

RED, GREEN & BLUE COLOR SELECTION

CH2 , Ch3 & CH4 control the intensity ratio of each of the RED, GREEN & BLUE

LEDs.

When the slider is at the highest position (255) the intensity of the color is the

maximum.

CH2 , Ch3 & CH4 can be combined together to create over 16 million colors.

COLOR MACRO

The COLOR MACRO channel allows the user to select from different color macro . Ch5 has priority over Ch2, Ch3 & Ch4.

STROBE

CH6 is the strobe channel and controls the strobe effects of CH2, CH3, Ch4, CH5 &

CH9

The strobe is with an adjustable speed with a maximum of 20Hz. The strobe is not active with CH7 & CH10

MODE SELECTION

CH7 allows the user to activate DMX MODE 1 (0-244) or DMX MODE 2 (245-255).

Ch7 has priority over Ch1 when first activated. Ch7 has priority over Ch10 when first activated.

When Color-Cycle Mode 4 is selected Ch9 controls the speed of the Color-cycle.

ID ADDRESS SELECTION

CH8 is used to select the target ID address. Each independent DMX address may have upto 66 independent ID addresses. An ID address of 0 will be activated by all ID address locations.

MODULE SELECTION

Ch9 controls set combinations of the three LED MODULES present in each unit.

EFFECT MACRO

The effect MACRO channel allows the user to select from combinations of different

colors and LED modules in a quick-and-easy action.

CH10 has priority over CH1. CH10 has priority over Ch7 when first activated

STAGE 2 DMX MODE 2

MODULE #1, MODULE #2 & MODULE #3 SELECTION

CH1, CH2 & CH3 allow quick-and-simple control of the three LED MODULEs Control of the LED MODULEs can be used in conjunction with all other channels in

DMX MODE 2

STROBE

CH6 is the strobe channel and controls the strobe effects of CH1, CH2 & Ch3 The strobe is with an adjustable speed with a maximum of 20Hz.

MODE SELECTION

CH7 allows the user to activate DMX MODE 1 (0-244) or DMX MODE 2 (245-255).

ID ADDRESS SELECTION

CH8 is used to select the target ID address. Each independent DMX address may have up to 66 independent ID addresses.

4 USING A DMX512 CONTROLLER

25

ARC 1 MODE

RED, GREEN & BLUE COLOR SELECTION

CH1 , Ch2 & CH3 control the intensity ratio of each of the RED, GREEN & BLUE

LEDs.

When the slider is at the highest position (255) the intensity of the color is the

maximum.

CH1 , Ch2 & Ch3 can be combined together to create over 16 million colors.

2008.8.13

PIXEL

Every color in each module used as one pixel.

For example, in module #1: 12 red leds = one pixel 12 green leds = one pixel 12 blue leds = one pixel

4 USING A DMX512 CONTROLLER

26

2008.8.13

4.4 PROGRAMMING WITH A DMX512 CONTROLLER: EXAMPLES(STAGE 1)

Before any operation is performed on the DMX512 controller, confirm that all DMX channels are set to zero.

NOTE

When programming a step / scene that involves operating CH10 to select an ID address, this channels operation should be performed first

EXAMPLE 1

CH1

CH2

CH3

CH9

CH10

Step 1

CH1

CH2

CH3

CH9

CH10

Step 2

CH1

CH2

CH3

CH9

CH10

Step 3

CH1

CH2

CH3

CH9

CH10

Step 4

CH1

CH2

CH3

CH9

CH10

Step 5

CH1

CH2

CH3

CH9

CH10

Step 6

to select ID Add. 1

to select DMX mode 2

to select RED for MODULE #1 (ID Add. 1)

to select ID Add: 1

to select OFF for MODULE #1

to select RED for MODULE #2 (ID Add. 1)

to select ID Add: 1

to select OFF for MODULE #2

to select RED for MODULE #3 (ID Add. 1)

to select all ID Addresses

to select OFF for MODULE #3

to select GREEN for MODULE #1 (ID Add. 1 & ID Add. 2)

to select all ID Addresses

to select OFF for MODULE #1 (ID Add. 1 & ID Add. 2)

to select GREEN for MODULE #2 (ID Add. 1 & ID Add. 2)

to select all ID Addresses

to select OFF for MODULE #2 (ID Add. 1 & ID Add. 2)

to select GREEN for MODULE #3 (ID Add. 1 & ID Add.2)

20

0

255

11

0

20

0

255

11

0

20

255

11

50

0

255

0

50

0

255

0

50

255

0

ID Addr.2ID Addr.1

ID Addr.1

ID Addr.2

ID Addr.1 ID Addr.2

to select OFF for MODULE #2 (ID Add. 1)

to select OFF for MODULE #3 (ID Add. 1)

to select DMX mode 2

to select OFF for MODULE #1 (ID Add. 1)

to select DMX mode 2

to select OFF for MODULE #2 (ID Add. 1 & ID Add. 2)

to select DMX mode 2

to select OFF for MODULE #3 (ID Add. 1 & ID Add. 2)

to select DMX mode 2

to select OFF for MODULE #1 (ID Add. 1 & ID Add. 2)

to select DMX mode 2

Red

Green

Blue

4 USING A DMX512 CONTROLLER

27

2008.8.13

Red

Green

Blue

Before any operation is performed on the DMX512 controller, confirm that all DMX channels are set to zero.

EXAMPLE 2

to select ID Add: 2

to select GREEN for MODULE #2 (ID Add. 2)

to select ID Add: 2

to select RED for MODULE #1 (ID Add. 2)

to select GREEN for MODULE #2 (ID Add. 2)

to select BLUE for MODULE #3 (ID Add. 2)

CH1

CH2

CH3

CH9

CH10

Step 1

CH1

CH2

CH3

CH9

CH10

Step 2

CH1

CH2

CH3

CH9

CH20

Step 3

CH1

CH2

CH3

CH9

CH10

Step 4

CH1

CH2

CH3

CH9

CH10

Step 5

CH1

CH2

CH3

CH9

CH10

Step 6

to select ID Add. 1

to select DMX mode 1

to select RED for all MODULES (ID Add. 1)

to select ID Add: 1

to select OFF for all MODULES (ID Add. 1)

to select ID Add: 2

to select BLUE for all MODULES (ID Add. 2)

to select all ID Addresses

to select OFF for MODULE #1 (ID Add. 2)

255

0

11

0

11

0

255

0

12

0

50

0

20

0

20

50

80

0

12

ID Addr.1 ID Addr.2

ID Addr.2

ID Addr.1

ID Addr.1 ID Addr.2

ID Addr.2ID Addr.1

ID Addr.1 ID Addr.2

ID Addr.1

ID Addr.2

to select NO GREEN for all MODULES (ID Add.1)

to select NO BLUE for all MODULES (ID Add.1)

to select NO GREEN for all MODULES (ID Add.1)

to select NO BLUE for all MODULES (ID Add.1)

to select DMX mode 1

to select NO RED for all MODULES (ID Add.2)

to select NO GREEN for all MODULES (ID Add.2)

to select DMX mode 1

to select NO GREEN for all MODULES (ID Add.1 & ID Add.2)

to select GREEN for all MODULES (ID Add.1 & ID Add.2)

to select NO GREEN for all MODULES (ID Add.1 & ID Add. 2)

to select DMX mode 2

to select OFF for MODULE #3 (ID Add.1)

to select DMX mode 2

4 USING A DMX512 CONTROLLER

28

2008.8.13

Red

Green

Blue

CH1

CH2

CH3

CH9

CH10

Step 7

CH1

CH2

CH3

CH9

CH10

Step 8

to select ID Add. 1

to set OFF for MODULE #1 (ID Add. 1)

to select ID Add: 2

0

11

255

0

12

to select DMX MODE 1

to select RED for all MODULES (ID Add. 2)

ID Addr.2ID Addr.1

ID Addr.2

ID Addr.1

to select OFF for MODULE 2 (ID Add.1)

to select OFF for MODULE 3 (ID Add.1)

to select DMX mode 1

to select NO GREEN for all MODULES (ID Add.2)

to select NO BLUE for all MODULES (ID Add.2)

4 USING A DMX512 CONTROLLER

29

2008.8.13

Before any operation is performed on the DMX512 controller, confirm that all DMX channels are set to zero.

EXAMPLE 3

Red

Green

Blue

CH1

CH2

CH3

CH9

CH10

Step 1

CH1

CH2

CH3

CH9

CH10

Step 2

CH1

CH2

CH3

CH9

CH10

Step 3

CH1

CH2

CH3

CH9

CH10

Step 4

CH1

CH2

CH3

CH9

CH10

Step 5

to select ID Add. 1

to select RED for all MODULES (ID Add. 1)

to select ID Add: 2

to select ID Add: 3

to select ID Add. 1

255

0

11

0

255

0

12

0

255

0

13

0

11

0

12

to select ID Add: 2

to select NO RED for all MODULES (ID Add.2)

to select NO GREEN for all MODULES (ID Add.2)

to select NO BLUE for all MODULES (ID Add.2)

to select NO GREEN for all MODULES (ID Add. 1)

to select NO BLUE for all MODULES (ID Add.1)

to select NO RED for all MODULES (ID Add.2)

to select GREEN for all MODULES (ID Add.2)

to select NO BLUE for all MODULES (ID Add. 2)

to select NO RED for all MODULES (ID Add.3)

to select NO GREEN for all MODULES (ID Add.3)

to select BLUE for all MODULES (ID Add.3)

to select NO RED for all MODULES (ID Add.1)

to select NO GREEN for all MODULES (ID Add.1)

to select NO BLUE for all MODULES (ID Add.1)

to select DMX mode 1

5 APPENDIX

30

2008.8.13

5.1 TROUBLE SHOOTING

5 APPENDIX

No display

1) Power connection error

2) Main PCB fuse overheated

3) Main PCB damaged

1) Check all power connections

2) Replace fuse

3) Replace main PCB

LED MODULE on, but no control from display

Display board damaged Replace display board

LEDs of the same color are not lit

LED PCB damaged

Replace PCB board

LEDs of all colors are not lit

Main PCB damaged

Replace main PCB

Display normal, but no respon se to DMX512 controller

1) Signal connection error

2) DMX address error

1) Check all signal connections

2) Check DMX address setting

SITUATION CAUSE

PART ORDER NUMBER

ACTION

26-2A-LED301MD4-00

16-03-0020-03

26-2A-LED301DI-01

26-2A-LED301Light-00

LED MODULE

26-2A-LED301MD4-00

Ve rsion 4 . 0

Briteq LED Blaster 108 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual