Britax Romer Kidfix 2 S, Kidfix 2 R User guide

bab

1. SAFETY NOTES 2. INTRODUCTION

Please take the time to read these instructions carefully and keep them to hand in the storage compartment provided on the child safety seat at all times! The instructions must accompany the child seat if it is passed on to athird party!

DANGER! To protect your child:

•

In the event of an accident at acollision speed of more than 10 km/h, the child seat may be damaged without the damage being immediately visible. In this case the child seat must be replaced. Please dispose of it properly.

•

Always have your child seat checked if it has been damaged (e.g by falling to the ground).

•

Regularly check all important parts for damage. In particular, ensure that all the mechanical parts are fully functional.

•

Never apply oil or grease to any parts of the child seat.

•

Never leave your child unattended on the child seat in the vehicle.

•

Only allow your child to enter and exit the vehicle on the pavement side.

•

Protect the child seat from intense direct sunlight when not in use. The child seat can become very hot in direct sunshine. Children's skin is sensitive and could be harmed as aresult.

•

The more snugly the belt ﬁts over your child's body, the better the child will be protected. Therefore, avoid having your child wear thick clothes under the belt.

•

On long journeys, take regular breaks in order to give your child the chance to run about and play.

DANGER! For the safety of all vehicle occupants:

In the case of an emergency stop or accident, unsecured objects or people may cause injury to other occupants in the vehicle. Therefore, please always ensure that ...

•

the backrests of the vehicle seats are locked (e.g. If there is afolding rear seat bench, check that it is latched in place).

•

all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are secured.

•

all persons in the vehicle have their seat belts fastened.

•

the child seat is secured whenever it is in the vehicle, even if not carrying achild.

WARNING! For your protection when handling the child seat:

•

Never use the child safety seat in afree-standing position, even for testing.

•

When swivelling the backrest up, back-rest

and the seat cushion09. You or your child’s ﬁngers could be

nothing must come between the

jammed and injured.

•

To avoid damage, ensure that the child seat is not jammed in between hard objects (car door, seat rails, etc.).

•

Keep the child seat in asafe place when not in use. Do not place heavy objects on the seat and do not store it directly next to sources of heat or in direct sunlight.

CAUTION! To protect your vehicle:

•

Certain car seat covers made from more sensitive materials (e.g. velour, leather, etc.) may show signs of wear when achild seat is used on them. For optimum protection of your car seat covers, we recommend using the BRITAX RÖMER car seat protector from our range of accessories.

If you have any further questions about the use of the child seat, please

BRITAX RÖMER Child Safety EMEA

www.britax-roemer.com | hello@britax-roemer.com

BRITAX RÖMER Kindersicherheit GmbH

Kindersicherheit GmbH Theodor-Heuss-Straße 9 89340 Leipheim Germany

+49 (0) 8221 3670 199

BRITAX Excelsior Limited

1 Churchill Way West Andover Hampshire SP10 3UW United Kingdom

+44 (0) 1264 386034

BRITAX Nordiska Barn AB

Jörgen Kocksgatan 4 SE-211 20 Malmö Sweden

We are delighted that you have chosen our child safely through anew stage in his or her life.

To protect your child correctly, the installed as described in these instructions!

These instructions use the following symbols:

Symbol Keyword Explanation

DANGER! Risk of serious physical injury

WARNING! Risk of minor physical injury

CAUTION! Risk of material damage

TIP! Useful notes

Instructions that follow aﬁxed sequence are numbered.

Example:

1. Press the button...

Belt guide colours

For clear dierentiation, the two vehicle seat belts are shown in dierent colours. The diagonal strap

shown in dark red and the lap belt 15 in bright red. The belt guides on the child safety seat follow the same colour scheme.

3. APPROVAL

BRITAX RÖMER

Child seat

KIDFIX² R KIDFIX² S

*ECE = European Standard for Child Safety Equipment

This child seat has been designed, tested and approved according to the requirements of the European Standard for Child Safety Equipment (ECE R 44/04). The certiﬁcation mark (letter E in acircle) and approval number can be found on the orange approval label (sticker on the child seat).

DANGER! The certiﬁcation is invalidated if any modiﬁcations are made to

the child seat. Only the manufacturer is permitted to make modiﬁcations to the child safety seat.

without SecureGuard.

WARNING! The securing your child in the vehicle. They are in no way suitable for use as aseat or atoy in the home.

DANGER! Never secure your child or the child seat with a2-point belt. If your child is secured in the child seat with a2-point belt only, this may cause serious injuries, which could even be fatal.

The child seat is approved for use both with and

KIDFIX² R and KIDFIX² S must be used exclusively for

child seat to accompany your

child seat must always be used and

Testing and certiﬁcation

In accordance with ECE* R 44/04

Group Body weight

II+III 15 to 36 kg

4. USE IN THE VEHICLE 6. CARE AND MAINTENANCE

Please refer to your vehicle’s instruction manual for instructions on how to use child restraint systems. The seat can be used in vehicles with ISOFIX anchoring systems (see type list) and in vehicles with 3-point belts.

Please refer to your vehicle’s instruction manual for information on the seats approved as child seats for weight class 15 to 36 kg.

The

KIDFIX² R and KIDFIX² S are approved for two dierent installation

methods:

Symbol Installation type Approval type

with the ISOFIT locking arms in the ISOFIX ﬁxing points on the vehicle. Check the list of vehicle types.

with the vehicle's 3-point seat belt universal

This means that the child seat may be used only in vehicles that are listed in the at-

tached vehicle type list. This type list is constantly being updated. The latest version can be obtained from us or at www.britax-roemer.com

You can install your child seat as follows:

in the direction of travel Ye s against the direction of travel No with 2-point belt No with 3-point belt with ISOFIX ﬁxing points

(between seat surface and backrest)

On front passenger seat Yes On outer rear seat Ye s on centre rear seat

(with 3-point belt)

Use is permitted on arear-facing vehicle seat (e.g. in avan or minibus) only if the vehi-

cle seat is also approved for use by adults. The seat must not be within the activated range of an airbag.

The safety belt must be approved to ECE R 16 or acomparable standard (indicated on

the belt’s test label by an "E" or "e" inside acircle).

If there is afront airbag: Slide the car seat well back and follow the related instructions

in the vehicle’s instruction manual.

Cannot be used if the vehicle seat is equipped with a2-point belt only.

Ye s

Yes

semi-universal

15 – 36 kg

Please ensure that you only use original BRITAX RÖMER replacement seat covers, as the seat cover is an integral part of the child safety seat and fulﬁls important functions that ensure smooth operation of the system. Replacement seat covers are available from your dealer.

•

The cover can be removed and washed with amild detergent, selecting the “Delicates” programme on the washing machine (30 °C). Please observe the instructions on the washing label of the cover.

•

The plastic parts can be cleaned in soapy water. Do not use aggressive cleaning agents (such as solvents).

DANGER! The child safety seat must not be used without the seat cover.

Removing the seat cover

1. Push the headrest of the vehicle seat to its top posi-

tion.

2. Unhook the cover hook

rest.

3. Pull o the top part of the cover and fold it forwards

onto the seat surface.

4. Release the cover hooks

rest and on both sides of the seat surface and loosen

the plastic cards on the front of the seat cushion.

5. Pull the cover away from the seat surface.

Removing the headrest cover

1. Unhook the cover straps

rest.

2. Unhook the cover hooks

rest.

3. Pull the headrest cover

two hooks on the bottom of the headrest.

o; to do this, detach the

► The cover can now be washed. Please observe the

instructions on the washing label of the cover.

Putting the cover on

Follow the above steps in the reverse order to put the cover on.

7. DISASSEMBLY AND DISPOSAL

UNFASTENING YOUR CHILD:

To unfasten your child, press the release button on the car seat buckle.

5. ADJUSTING THE HEADREST

A correctly adjusted headrest nal strap

, and gives your child optimum protection. The headrest 22 must be positioned so that two ﬁngers can be inserted between your child's shoulders the headrest

To adjust the height of the headrest to ﬁt your child:

1. Grasp the adjustment handle

headrest 22 and pull it upwards. This unlocks the

headrest.

2. You can now move the unlocked headrest

the desired height. When you release the adjustment handle 10, the headrest

3. Place the child seat on the car seat.

4. Sit your child on the child seat and check the height.

Repeat the above procedure until the headrest at the correct height.

ensures optimal positioning of the diago-

on the back of the

locks into place.

DANGER! The child seat must always be secured when in the vehicle, even

if not carrying achild.

RE-ATTACHING THE BACKREST:

4. Follow steps 1 - 7 in paragraph 10.1 “Removing the backrest“ in the re-

verse order.

Please follow the disposal regulations applying in your country.

Disposal of packaging Container for cardboard boxes Seat cover Residual waste, thermal recycling Plastic parts To be placed in the corresponding container

Metal parts Container for metals Belt straps Container for polyester Buckle and clip Residual waste

REMOVAL:

1. Press the release button on car vehicle seat buckle.

2. Open the dark red belt holder

button on the belt holder

the diagonal

belt

Only for installation type A (ISOFIT):

3. To release the ISOFIT ﬁtting, squeeze the green locking button

and red release button

on one side then on the other.

►The child safety seat can now be removed.

as labelled

on the rear of the back-

on the front of the back-

on the rear of the back-

on the front of the back-

by pressing the

backwards, then pull out

together, ﬁrst

8. Remove and install SecureGuard

We recommend using the seat with SecureGuard.

TIP!

The following chapters describe use with

SecureGuard.

8.1

8.2

Remove SecureGuard

Remove the seat cover

1. Fold up the cover of the backrest

2. Fold the cover of the seat shell

3. Unhook the cover straps on the seat shell 29.

4. Pull the SecureGuard

downward and away through the

seat cover.

5. Remove the plastic cards

shell

6. Remove the cover and the seat cushion.

Remove SecureGuard

1. Press the SecureGuard

cureGuard

out of the recess 31.

TIP! Keep the SecureGuard 13 for later use.

Mounting the seat cover

1. Position the seat cover on the seat shell

2. Insert the plastic cards

designated recesses on the seat shell

3. Pull the seat cover over the seat shell

4. Hook the cover straps back onto the seat shell

5. Position the seat cover behind the backrest cover

Installing SecureGuard

Remove the seat cover

1. Fold up the cover of the backrest

2. Fold the cover of the seat shell

3. Unhook the cover straps on the seat shell 29.

of the seat cover from the seat

downward and slide the Se-

of the seat cover into the

forwards.

4. Remove the plastic cards

seat shell

of the seat cover from the

5. Remove the cover and the seat cushion.

Attaching SecureGuard

1. Take the SecureGuard

the recess

2. Slide and press the metal plate

until the plate

and position it right in front of

clicks into place.

into the recess 31

Mounting the seat cover

1. Position the seat cover on the seat shell

2. Pull the SecureGuard

through the slot in the seat

cushion.

3. Insert the plastic cards

nated recesses on the seat shell

4. Pull the seat cover over the seat shell

5. Hook the cover straps back onto the seat shell

6. Position the seat cover behind the backrest cover

of the seat cover into the desig-

15 kg – 36 kg

(~4 Y – 12 Y)

KIDFIX² R

KIDFIX² S

User instructions

2000031236 19/12

www.britax-roemer.com

9. Installation with backrest

9.1

The child seat is installed permanently in the vehicle with the ISOFIT locking arms

seat belt.

1. If your vehicle is not equipped with ISOFIX seat ﬁttings as standard,

TIP! The ISOFIX ﬁxing points are located between the seat surface and

* The insertion aids make it easier to install the child seat with ISOFIX ﬁxing points and

prevent damage to the car seat covers. If they are not being used, remove them and keep them in asafe place. For vehicles with afolding backrest, the insertion aids need to be removed before folding the backrest. Any problems that occur are usually caused by dirt or external objects on the insertion aids and on the hook. Remove the dirt or external objects to resolve such problems.

2. Push the headrest of the vehicle seat to its top position.

3. Follow the steps in Section 5 “ADJUSTING THE HEADREST”.

► the child seat is engaged on both sides with the ISOFIT locking arms

► the lap belt

► the lap belt ► the diagonal strap

► the diagonal strap

► the diagonal strap ► the straps are tight and not

With ISOFIT + BACKREST

. Your child is then buckled into the child seat using the vehicle's 3-point

clamp the two insertion aids

supplied with the seat*, with notch facing

upwards, onto the two ISOFIX ﬁxing points 01 in your vehicle.

the backrest of the vehicle seat.

4. Hold down the ISOFIT setting button

the ISOFIT locking arms 05 fully out.

5. On either side of the seat, squeeze the green locking

button This ensures that both hooks on the ISOFIT locking

and the red release button

arms 05 are open and ready to use.

6. Place the child seat facing forward on acar seat ap-

proved for this purpose. Check that the backrest is ﬂat against the backrest of the car seat.

7. Position the two ISOFIT locking arms

front of the two insertion aids

8. Push both ISOFIT locking arms

aids 02 until the ISOFIT locking arms 05 engage on

both sides with an audible click.

DANGER! The green locking button

ble on both sides, indicating that the child seat is correctly fastened.

9. Hold down the ISOFIT setting button

the child seat as far back as possible.

10. Shake the child seat to check that it is securely fas-

tened, and check the locking buttons sure that they are both fully green.

11. Carry out the steps in paragraph 9.3 "SECURING

For the safety of your child, before every car journey check that...

THE CHILD IN A CHILD SEAT WITH BACKREST".

in the ISOFIT ﬁxing points 01 and both locking buttons 07 are fully green;

is passed into the bright red belt guides

of the seat cushion;

into the bright red belt guide

is passed through the bright red SecureGuard 13;

on the vehicle belt buckle side 18 is also passed

on the seat cushion;

is passed through the dark red belt holder 03 at the

headrest;

runs diagonally backwards;

twisted;

into the insertion

and push

together.

directly in

must be visi-

and push

again to en-

on both sides

► the vehicle belt buckle

is not placed in the bright red belt guide 04 on

the seat cushion.

DANGER! If your child tries to open the ISOFIT locking buttons

the vehicle belt buckle, red SecureGuard

or to insert the diagonal strap 16 into the bright

, stop your vehicle as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

9.2

Follow the steps in Section 5 "ADJUSTING THE HEADREST".

With 3-POINT BELT + BACKREST

1. Place the child seat on the car seat.

Check that the backrest rest of the car seat.

is ﬂat against the back-

TIP! If the headrest of the car seat is preventing this,

it should be removed and stowed safely somewhere in the vehicle.

2. Carry out the steps in paragraph 9.3 "SECURING THE CHILD IN A CHILD SEAT WITH BACKREST".

For the safety of your child, before every car journey check that...

► the child seat is securely fastened, ► the lap belt

is passed into the bright red belt guides

of the seat cushion,

► the lap belt ► the diagonal strap

into the bright red belt guide

► the diagonal strap

is passed through the bright red SecureGuard

on the vehicle belt buckle side 18 is also passed

on the seat cushion,

is passed through the dark red belt holder

headrest,

► the diagonal strap ► the straps are tight and not

► the vehicle belt buckle

runs diagonally backwards,

twisted,

is not placed in the bright red belt guide 04 on

the seat cushion.

DANGER! If your child tries to open the vehicle belt buckle

the diagonal strap

into the bright red SecureGuard 13, stop your vehicle as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

9.3

SECURING THE CHILD IN A CHILD SEAT WITH BACKREST

KIDFIX² S

On the side nearer the vehicle door, turn the SICT anti-clockwise until it is at adistance of 5 mm from

the vehicle door or until it is fully unscrewed.

All versions:

Pull out the vehicle belt and pass it in front of your child to the vehicle belt buckle

DANGER! Check that the vehicle belt is not twisted,

otherwise the full protective eect of the restraint

system is not ensured.

2. Engage the belt clip in the vehicle belt buckle

that there is an audible CLICK.

3. Insert the diagonal strap

and lap belt 15 on the vehicle belt buckle side 18 into the bright red belt guide 04 on the seat cushion.

DANGER! The vehicle belt buckle

tioned between the bright red belt guide 04 and the

armrest.

must not be posi-

on both sides

at the

or insert

in the bright red belt guide

must lie as low as possible

in the bright red SecureGuard

is fully

is lying over

into the

into the dark red belt

without twisting.

is covering the belt holder 03,

upwards. The diago-

must run diagonally

must never run for-

For the safety of

7. So as not to lose them, screw the 4 screws back into

the holes provided in the backrest

10.2

8. Pull the seat cushion cover

transparent plastic piece onto the notch provided.

USING THE FLEXIBLE BELT GUIDE

For design reasons in some vehicle models, the diagonal strap shoulder area. When using as abooster seat, always check that the diagonal strap 16 is located in the area

indicated. If the diagonal strap

may not pass ideally over your child's

back and hook the

does not pass

through the correct (green) area, the ﬂexible belt guide

must also be used.

Attaching the ﬂexible belt guide - securing with ISOFIT locking arms

1. Open the ﬂap on the storage compartment

bottom of the seat cushion ble belt guide

2. Close the ﬂap on the storage compartment

3. Pass the metal attachment

ing arm 27 located on the vehicle belt buckle side.

4. Place the belt guide clip

”

on the sitting surface of the seat cushion

5. Follow the remaining steps for the installation meth-

10.3 FASTENING WITH ISOFIT LOCKING ARMS

AS A SEAT CUSHION WITHOUT BACKREST

and take out the ﬂexi-

over the ISOFIX lock-

of the ﬂexible belt guide

6. Attach the belt guide clip

Check that the belt of the ﬂexible belt guide

twisted.

to the diagonal strap.

is not

into the bright red belt guide

► the diagonal strap

► the straps are tight and not ► the vehicle belt buckle

on the seat cushion,

runs diagonally backwards,

twisted,

is not placed in the bright red belt guide 04

on the seat cushion.

7. Adjust the belt in the belt guide clip

agonal strap

agonal belt is not in the green area even with the ﬂexible belt guide used without the backrest on this seat.

is located in the green area. If the di-

, the child seat must not be

DANGER! The diagonal belt must always be located

in the area indicated.

so that the di-

DANGER! If your child tries to open the ISOFIT locking buttons

the vehicle belt buckle

red SecureGuard

, stop your vehicle as soon as possible. Check that

or to insert the diagonal strap

into the bright

the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

10.3

The child seat is installed permanently in the vehicle with the ISOFIT locking arms. Your child is then buckled into the child seat with the vehicle's 3-point seat belt.

FASTENING WITH ISOFIT LOCKING ARMS AS ABOOSTER SEAT WITHOUT BACKREST

10.4

FASTENING WITH 3-POINT BELT AS A SEAT CUSHION WITHOUT BACKREST

The child seat is not installed permanently in the vehicle. It is simply secured along with your child by the vehicle's 3-point seat belt.

on the

1. If your vehicle is not equipped with ISOFIX seat ﬁttings as standard,

clamp the two insertion aids

supplied with the seat*, with notch facing

upwards, onto the two ISOFIX ﬁxing points 01 in your vehicle.

TIP! The ISOFIX ﬁxing points are located between the seat surface and

1. Place the child seat on asuitable vehicle seat.

Follow the steps in paragraph 10.5 “SECURING THE CHILD IN A CHILD SEAT WITHOUT BACKREST”.

the backrest of the car seat.

* The insertion aids make it easier to install the child seat with the ISOFIX ﬁxing points and

they prevent damage to the car seat covers. If they are not being used, remove them and keep them in asafe place. For vehicles with afolding backrest, the insertion aids need to be removed before folding the backrest. Any problems that occur are usually caused by dirt or external objects on the insertion aids and on the hook. Remove the dirt or external objects to resolve such problems.

2. Hold down the ISOFIT setting button

and push

the ISOFIT locking arms 05 fully out.

For the safety of your child, before every car journey check that...

► the child seat is securely fastened, ► the lap belt

is passed into the bright red belt guides 14 on both sides

of the seat cushion,

► the lap belt ► the diagonal strap

into the bright red belt guide

► the diagonal strap ► the straps are tight and not

► the vehicle belt buckle

is passed through the bright red SecureGuard 13,

on the vehicle belt buckle side 18 is also passed

on the seat cushion,

runs diagonally backwards,

twisted,

is not placed in the bright red belt guide 04 on

4. Also place the lap belt

on the other side of the seat cushion.

DANGER! The lap belt

over your child's hips on both sides.

5. Insert the lap belt

DANGER! Do not pass the diagonal strap

bright red SecureGuard

6. Pass the diagonal strap

holder 03 at the headrest 22 until it is fully inside the belt holder

TIP! If the backrest

youcan adjust the headrest nal strap

the headrest sure that the button on the belt holder closed.

can then be easily inserted. Now move

back to the correct height. Make

7. Make sure that the diagonal strap

your child's collarbone and not at his or her neck.

TIP! You can still also adjust the height of the head-

rest

in the vehicle.

DANGER! The diagonal strap

backwards. You can adjust the belt routing with the adjustable belt deﬂector in the vehicle.

DANGER! The diagonal strap

ward to the belt deﬂector on the vehicle. In this case, use the child seat on the rear seat only.

8. Tighten the vehicle belt by pulling on the diagonal

strap

9. Follow the steps listed in Section 9 “ your child, before every car journey check that ...

the seat cushion.

6. Attach the belt guide clip

to the diagonal strap

. Check that the belt of the ﬂexible belt guide

not twisted and passes diagonally behind your child.

070605

3. On both sides of the seat, squeeze the green locking

button

and the red release button 06 together. This ensures that both hooks on the ISOFIT locking arms 05 are open and ready to use.

DANGER! If your child tries to open the vehicle belt buckle

the diagonal strap

into the bright red SecureGuard 13, stop your vehi-

or insert

cle as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

10. USING AS A BOOSTER SEAT

10.1

For age group 3 (22 kg to 36 kg), the

REMOVING THE BACKREST

child seat can also be used as aboost-

7. Adjust the belt guide clip

strap

is located in the green area.

DANGER! The diagonal strap

so that the diagonal

must always be in

the area indicated.

er seat without the backrest. Follow the steps described below for the removal and attachment of the backrest. You will need aTX20 Torx screwdriver. BRITAX RÖMER recommends using it with the backrest as this

Attaching the ﬂexible belt guide - securing with the vehicle 3-point belt

provides your child with optimum protection in the case of aside impact. If using without the backrest, sucient side impact protection can be ensured

only with side curtain airbags at the seat positions. For information about

vehicle equipment options, please contact the manufacturer of your vehicle.

DANGER! Use this product as abooster seat only if your child is in age

group3 (22 to 36 kg) and is taller than 125 cm. For all other age groups, the product must be used with the backrest .

1. Open the ﬂap on the storage compartment

bottom of the booster seat and take out the ﬂexible belt guide 24.

2. Close the ﬂap on the storage compartment

on the

We recommend using the seat with the backrest for as long as possible, and as abooster seat starting from achild height of 135 cm.

in the ISOFIX lock-

1. Place the seat on alevel surface.

2. Open the ﬂap on the storage compartment

bottom of the booster seat and take out the

on the

Torx

3. Engage the metal attachment

ing arm 27 located on the vehicle belt buckle side.

screwdriver.

3. Lift the cover of the backrest

4. Lift the cover of the seat cushion

and fold it forward.

and fold it back-

ward.

4. Place the belt guide clip

on the sitting surface of the booster seat.

5. Follow the remaining steps for the installation meth-

10.4 FASTENING WITH 3-POINT BELT AS A

SEAT CUSHION WITHOUT BACKREST

of the ﬂexible belt guide

► the child seat is engaged on both sides with the ISOFIT locking arms

For the safety of your child, before every car journey check that...

in the ISOFIT ﬁxing points 01 and both locking buttons07 are fully

green,

► the lap belt

5. Loosen the 4 Torx screws on the backrest

6. Push the seat cushion

until the connection snaps out.

towards the backrest 12

sides of the seat cushion,

► the lap belt ► the diagonal strap

4. Place the child seat facing forward on acar seat ap-

proved for this purpose.

5. Position the two ISOFIT locking arms

front of the two insertion aids 02.

6. Push both ISOFIT locking arms

into the insertion aids02 until the ISOFIT locking arms 05 engage on both sides with an audible click.

DANGER! The green locking button

must be visible on both sides, indicating that the child seat is correctly fastened.

7. Hold down the ISOFIT setting button

the child seat as far back as possible.

8. Shake the child seat to check that it is securely fas-

tened, and check the locking buttons

ensure that they are both fully green.

9. Carry out the steps in paragraph 10.5 "SECURING THE CHILD IN A CHILD SEAT WITHOUT BACKREST".

is passed into the bright red belt guides

is passed through the bright red SecureGuard 13,

on the vehicle belt buckle side 18 is also passed

on both

directly in

and push

again to

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

10.5

SECURING THE CHILD IN A CHILD SEAT WITHOUT BACKREST

1. Sit your child sit in the child seat.

2. Pull out the vehicle belt and pass it in front of your

child to the vehicle belt buckle

DANGER! Check that the vehicle belt is not twisted,

otherwise the full protective eect of the restraint system is not ensured.

3. Engage the belt clip in the vehicle belt buckle

that there is an audible CLICK.

4. Insert the diagonal strap

vehicle belt buckle side 18 into the bright red belt guide 04 on the seat cushion.

DANGER! The vehicle belt buckle

the same area as the bright red belt guide

and lap belt 15 on the

should not be in

The lap belt 15 must lie as low as possible over your child's hips on both sides.

5. Insert the lap belt

DANGER! Do not insert the diagonal strap

bright red SecureGuard

in the bright red SecureGuard

into the

Britax Romer Kidfix 2 S, Kidfix 2 R User guide

Specifications and Main Features

Frequently Asked Questions

User Manual