Britax Romer Advansafix M i-Size User guide

Please take the time to read these instructions carefully and always keep

them in the storage pouch provided The instructions must accompany the child seat if it is later passed on to athird party.

DANGER! For the protection of your child:

• Before closing the vehicle door, check that neither your child nor any parts of the child seat can get jammed in the door.

• In the event of an accident at a collision velocity greater than 10 km/h, it is possible that the child seat may be damaged without the damage being immediately visible. In this case the child seat must be replaced. Please dispose of it properly.

• Always have the child seat examined if it has been damaged (e.g. if it falls to the ground).

• Regularly check all important parts for damage. In particular, ensure that all the mechanical parts are fully functional.

• Never lubricate any parts of the child seat with grease or oil.

•

Never leave your child unattended in the child seat in the vehicle.

• Have your child enter and exit the vehicle on the pavement side only.

• When not in use, protect the child seat from direct exposure to sunlight. The child seat can become very hot in direct sunshine. Children's skin is sensitive and could be harmed as a result.

•

7KHPRUHVQXJO\WKHEHOW¿WVRYHU\RXUFKLOGVERG\WKHVDIHU\RXUFKLOGZLOOEH7KHUHfore, avoid having your child wear thick clothes under the belt.

• On long journeys, take regular breaks in order to give your child a chance to run about and play.

• If using on the rear seat: Move the front seat far enough forward to ensure that your child's feet will not knock against the backrest of the front seat (to prevent the risk of injury).

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or accident, unsecured objects or people may cause injury to other occupants in the vehicle. Therefore, please always ensure that ...

QRORDGEHDULQJFRQWDFWSRLQWVDUHXVHGRWKHUWKDQWKRVHVSHFL¿HGLQWKHVH

instructions and those marked on the child seat.

• the backrests of the car seats are secured (for example, check that any folddown rear seat bench has snapped into place).

• all heavy or sharp-edged objects present in the vehicle (e.g. on the parcel shelf) are held securely.

• all persons in the vehicle have their seatbelts fastened.

• the child seat is secured whenever it is in the vehicle, even if it is not carrying a child.

14 on the child seat for later reference.

2.1 Use as intended

This child seat has been designed, tested and approved according to the requirements of the European Standard for Child Safety Equipment (UN 129/03). It is designed to secure a child in the vehicle. It may only be used on forward-facing or rear-facing vehicle seats. It is not a toy and is not suitable for use as a seat outside the vehicle.

2.2 SAFETY NOTES

Elimination of the protective function through modiﬁcations

Unauthorised technical changes can cause the protective function of the seat to be reduced or completely eliminated. The certiﬁcation is invalidated if any modiﬁcations are made to the child seat.

• Do not make any technical changes to the child safety seat.

• Only the manufacturer is permitted to make modiﬁcations to the child safety seat.

Risk of injury through improper use

If you do not use this product as intended, serious injury or death may result.

• Never secure the child seat with a 2-point seat belt.

• Read and follow the instruction manual for the vehicle used to transport this child seat.

• If there is a front airbag, slide the vehicle seat a long way back.

• If in doubt, refer to the manufacturer or the vendor of the child restraint system.

• Use the child seat according to the body height of the child to be secured.

2.3 Requirements

This child seat is approved for three installation methods, A, B1 and B2. Use the installation method depending on the size of the child to be secured.

Tip! The installation methods can be found in Section 5 “Installation & Use”

[pageII].

Tip! Information on the vehicle seats can be found in the instruction manual for

the vehicle. If in doubt, refer to the manufacturer or vendor of the vehicle.

From 15 months / 76 cm – 102 cm / up to 21 kg (i-Size Universal ISOFIX)

Use installation method A. The child seat may only be used on the following vehicle seats:

• Vehicle seats with i-Size approval.

• Vehicle seats approved for ISOFIX size class “B1” and a body weight of the child to be secured of 9–18kg. In addition, the vehicle seat position must have a top tether anchorage point.

100 cm – 133 cm (i-Size booster seat)

Use installation method B1 on vehicle seats with i-Size approval. The child seat may also be used on vehicle seats which are included in the enclosed vehicle type list.

Alternatively, you may use installation method proval or universal approval.

Tip! Some vehicle seats reduce the adjustability of the child seat. This aects the

“Adjust seat angle” and “Adjust headrest” functions.

133 cm - 150 cm (Speciﬁc vehicle booster seat)

Use installation method B1 or B2. The child seat may only be used in vehicle seats that are listed in the attached vehicle type list.

Tip! The latest version of this list can be obtained from our website.

www.britax-roemer.com

B2 on vehicle seats with i-Size ap-

3. CARE AND MAINTENANCE1. GENERAL SAFETY INSTRUCTIONS 2. USE IN THE VEHICLE

TAKING CARE OF THE HARNESS BUCKLE

To ensure the safety of your child, it is essential that the harness buckle continues tofunction correctly. Harness buckle malfunctions are usually caused by dirt accumulation or by external objects. Such malfunctions may be:

• When you press the red release button, the buckle clips are ejected only slowly.

• The buckle clips no longer engage (i.e. they pop out again when you try to push

them in).

• The buckle clips do not engage without an audible click.

• The buckle clips are dicult to push in (you feel a certain amount of resistance).

• It takes a lot of force to open the harness buckle.

Remedy

Rinse out the harness buckle so that it works perfectly again:

CLEANING THE HARNESS BUCKLE

1. Open the Velcro fastener on the crotch cushion

2. Remove the grey release plate

as described in Section “10. REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

3. Place the release plate

along with the harness buckle 20 in warm water

withsome washing-up liquid for at lease one hour.

4. Thoroughly rinse the harness buckle

5. Attach the grey release plate

as described in Section 10. “ REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

6. Attach the crotch cushion

CLEANING

CAUTION Please ensure that you use only original BRITAX replacement seat

covers, as the seat cover is an integral part of the child seat and is important for correct functioning of the system. Replacement seat covers are available from your dealer.

CAUTION! The child seat must not be used without its cover.

• The seat cover can be removed and washed with a mild detergent in a washing

machine with the “Delicates” programme (30 °C). Please follow the instructions onthe washing label of the seat cover.

• The shoulder cushions can be removed and washed in lukewarm soapy water.

• The plastic parts, belts, and SecureGuard can be cleaned with soapy water.

Donotuse any aggressive cleaning agents (such as solvents).

and remove it.

and dry it completely.

Removing the cover Headrest

1. Open the two press studs

at the belt slots.

2. Push the headrest of the child seat to the topmost position.

3. Pull the elastic band up from the edge of the tray and pull the tabs

out

ofthetwo slots in the seat pan.

4. Pull the cover edge out of the gap between the seat pan and the inlay cushion.

5. Unhook the rubber loops

under the headrest.

Seat pan

6. Undo the Velcro fastener on the crotch cushion

7. Open the four press studs

8. Push the harness buckle

9. Unhook the rubber loops

out of the seat pan.

on the seat and back surface.

or SecureGuard 26 through the cover slot.

at the front under the seat surface and pull the tabs

and remove it.

10. Pull the rubber loops carefully out of the gap around the belt guides

11. Pull the cover edge and tabs

out of the gap between the seat pan

andtheinlay cushion.

12. Pull the rubber loops

at the top of the back of the backrest out of the gap

inthe seat pan and and unhook them.

Reattaching the cover:

Simply follow the steps above in reverse order.

CAUTION! If the child seat is installed with Method A, always install the harness

buckle

correctly, and if installed with Method

correctly. Make sure that the release plate 32 is correctly attached.

B, always install SecureGuard

CAUTION! Check that the straps are not twisted and are laid correctly through

the slots in the cover. The rear slot in the seat cover is provided for the harness

buckle front edge of the seat is for the harness adjusting strap

and the front slot is provided for the SecureGuard 26. The slot at the

Removing the shoulder cushions

1. Loosen the shoulder straps

2. Open the shoulder cushions

as far as possible.

by the Velcro fasteners at the side.

Child seat back

3. Bring the top tether

4. Unhook the storage pouch

5. Pull out the shoulder straps

oftheshoulder cushions

6. Unhook the rubber loops from the plastic bars adjuster

7. Pull the shoulder cushions

forward over the front of the seat.

at the top.

a little so that you can see the rubber loops

underneath.

on the shoulder strap height

forwards out of the harness slots.

Reattaching the shoulder cushions

Simply follow the steps above in reverse order.

CAUTION The shoulder cushions

over. The shoulder straps inthe shoulder cushions

and belts must not be twisted or swapped

must be located under the black cover band 43

WARNING! For your protection when handling the child seat:

• Never use the child seat in a free-standing position, not even for testing.

•

To avoid damage, ensure that the child seat is not jammed in between hard objects (car door, seat rails, etc.).

•

Keep the child seat in a safe place when not in use. Do not place heavy objects on the seat and do not store directly next to heat sources or in direct sunlight.

CAUTION! To protect your vehicle:

• Certain car seat covers made from more sensitive materials (e.g. velour, leather, etc.) may show wear marks after a child seat has been used. For optimum protection of your car seat covers, we recommend using the BRITAX RÖMER car seat protector from our range of accessories.

9. DISPOSAL

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, waste incineration

Plastic parts To be placed in the corresponding container

Metal parts Container for metals

Belt straps Container for polyester

Buckle and clip Residual waste

www.britax-roemer.com | hello@britax-roemer.com

BRITAX RÖMER Kindersicherheit GmbH

Kindersicherheit GmbH Theodor-Heuss-Straße 9 89340 Leipheim Germany

+49 (0) 8221 3670 199

according to the labels

BRITAX RÖMER Child Safety EMEA

BRITAX Excelsior Limited

1 Churchill Way West Andover Hampshire SP10 3UW United Kingdom

+44 (0) 1264 386034

BRITAX Nordiska Barn AB

Jörgen Kocksgatan 4 SE-211 20 Malmö Sweden

10. REMOVING THE 5-POINT HARNESS AND RE-ATTACHING SECUREGUARD

21 44

5. Open the two shoulder cushions

6. Push the Velcro strip of the two opened shoulder cushions

restcover and attach it to the ﬂeece strip provided. Check that the two shoulder cushions are not overlapping.

7. Pull the adjusting strap

to tighten the harness.

8. Release the two press studs on the seat cover and fold the cover forwards. Whiledoing this, pull the harness buckle

“We recommend using the 5-point harness as long as possible. Only install the SecureGuard when the child to be secured is taller than 102 cm.”

1. Loosen the 5-point harness on the child seat as far as possible

2. Open the harness buckle and place the belt clips

in the belt guides

onthesides.

3. Loosen the press studs on the backrest and fold the upper half of the cover up- wards and the lower half downwards.

4. Insert the belt clips

in the recess provided on the 44 inside of the backrest.

11. RE-ATTACHING THE 5-POINT HARNESS AND REMOVING SECUREGUARD

Child seat back

1. Slide the headrest

2. Press the safety catch at the centre of the height change switch

to the lowest position.

, at the same

time moving it to the upper position.

Tip! The headrest

can be adjusted for body heights between 76cm and

102cm.

Child seat front

3. Fold the lower part of the headrest cover upwards and lay it over the headrest.

4. Open the two press studs on the inside of the headrest cover.

5. Release the two press studs on the back of the cover.

6. Release the two press studs on the seat cover and fold the cover forwards.

Whendoing so, pull the SecureGuard

7. Loosen the 5-point harness

on the child seat as far as possible.

Tip: Pull the two shoulder straps forward while pressing the adjustment button

8. Release the two opened shoulder cushions 19 from the Velcro strip and fold them

around the shoulder straps

by the Velcro fasteners on the side.

under the back-

out of the cover.

9. Raise the grey release plate towards the backrest

10. Turn the grey release plate around and the harness buckle (A)

11. Stow the harness buckle

back into the holder until it engages with an audible click.

12. Pass the SecureGuard

DANGER Make sure that the shoulder straps

der cushions

9. Remove the belt clips

10. Raise the grey release plate

the backrest 30.

11. Turn the grey release plate and the SecureGuard

and push it along with the harness buckle 20

in the recess provided and push the grey release plate

through the slot in the cover with sow-on B.

from the recess provided on the 44 inside of the backrest.

is at the bottom.

so that the SecureGuard (B) 26 is at the top

is at the bottom.

and push it along with the SecureGuard 26 towards

around so that the harness buckle 20 is at the top

pass correctly through theshoul-

13. Close the two bottom press studs on the cover.

14. Close the two top press studs on the cover.

15. Close the two press studs on the upper cover of the headrest.

Child seat back

16. Press the safety catch at the centre of the group change switch

, at the same

time moving it to the upper position.

Tip! The headrest

can be adjusted for body heights between 100cm and

150cm.

12. Store the SecureGuard

back into its holder until it engages with an audible click.

in the recess provided and push the grey release plate

13. Pass the harness buckle 20 through the slot in the cover which is nearer tothebackrest.

14. Close the two bottom press studs on the cover.

15. Close the two top press studs on the cover.

16. Close the two press studs on the upper cover of the headrest.

76 - 150 cm

ADVANSAFIX M i-SIZE

User instructions

www.britax-roemer.com

2000033377 - 03/20

click

1 cm

click

4. PREPARATORY STEPS

First please read the section describing the desired installation method in Section 5.

4.1 Preparing ISOFIX

1. If your vehicle is not ﬁtted with ISOFIX insertion aids

0506

as standard, clamp the two insertion aids are supplied along with the seat*), with recess facing upwards, into the two ISOFIX ﬁxing points vehicle.

TIP: The ISOFIX ﬁxing points are located between

theseat surface and the backrest of the car seat.

2. Move the headrest of the car seat to its topmost position.

3. Pull the grey handle

the ISOFIX locking arms

4. On both sides of the ISOFIX locking arms, squeeze the

green locking button 05 and the red release button

together. This ensures that both hooks on the ISOFIX

locking arms

A properly adjusted headrest your child on the child seat. Regularly check that the height of the headrest The headrest

are at the same level as your child’s shoulders, or slightly

higher.

ŹThe shoulder straps

zontal or just above your child’s shoulders.

ŹThe shoulder straps

back, or placed level with or above the child’s ears.

The shoulder straps are adjusted as follows:

1. Loosen the 5-point harness aspossible.

2. Press and hold the adjustment handle headres t

3. The unlocked headrest height. When you release the adjustment handle headrest

A correctly adjusted headrest

belt protection. Regularly check that the height of the headrest suitable for the body height of your child: The headrest inserted between the headrest

To adjust the height of the headrest to ﬁt your child:

1. Press and hold the adjustment handle headrest

2. The headrest desired height. When you release the adjustment handle the headrest

3. Place the child seat on the car seat.

4. Sit your child on the child seat and check the height.

Repeat this procedure until the headrest height.

is optimally positioned and gives your child optimum

at the back of the child seat until

are fully extended.

are open and ready to use.

ensures optimal protection for

is suitable for the body height of your child:

must be adjusted so that the shoulder straps

must be adjusted so that they arehori-

must not be passed behind the child’s

on the child seat as far

locks into place.

must be positioned so that two ﬁngers can be

can now be moved to the desired

ensures that the diagonal

and your child's shoulders.

is now unlocked and can be moved to the

locks into place.

(which

in your

on the back ofthe

is at thecorrect

* The insertion aids make it easier to install the child seat using the ISOFIX ﬁxing points and they prevent damage to the car seat covers. If they are not being used, remove them and keep them in a safe place. For vehicles with a folding backrest, the insertion aids need to be removed before folding the backrest. Any problems that occur are usually caused by dirt or external objects on the insertion aids and onthe hook. Remove the dirt or external objects to resolve such problems.

4.2 Adjusting the headrest (76 - 102 cm / ≤ 21 kg)

4.3 Adjusting the headrest (100 - 150 cm)

, the

5. INSTALLATION & USE

76 - 102 cm / ≤ 21 kg

With ISOFIX + Top Tether

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.

1.2 Follow the steps in Section 4.2 “ADJUSTING THE HEADREST (76 - 102 cm / ≤ 21kg)”.

2. PREPARING THE TOP TETHER

2.1 Unhook the snap-on hook

2.2 Take the top tether

2.3 Place the child seat in the direction of travel on an ap-

2.4 Take the top tether

2.5 Guide the top tether

3. FIXING THE TOP TETHER

Attach the snap-on hook

CAUTION! Check that you are not using luggage hooks

Look for the following symbol in your vehicle:

4. FASTENING THE ISOFIX

4.1 Position the two ISOFIX locking arms

4.2 Push the two ISOFIX locking arms

DANGER! The green locking button

5. PRESSING THE CHILD SEAT BACKWARDS Push the child seat ﬁrmly backwards as far as it will go.

6. CHECKING FOR CORRECT FASTENING

Shake the child seat to check that it is securely fastened

7. TIGHTENING THE TOP TETHER

Tighten the top tether

fastening on the back of the child seat.

the child seat.

proved car seat. Adjust the backrest angle of the car seat so that the gap between the car seat and the child seat is as small as possible.

away from the belt to extend it, and pull the top tether at the snap-on hook

the headrest to the top tether

mended in your vehicle's instruction manual.

instead of the top-tether anchorage points.

the two insertion aids

until the ISOFIX locking arms 04 engage on both sides

with an audible click.

both sides indicating that the child seat is correctly fastened.

and check the locking buttons indicators are fully green.

, for integrated headrests on the side closer

anchorage point of the vehicle.

turns green and the top tether

of the top tether 13 from the

out of the pouch

and press the metal tongue 15

in the middle between the bars of

to the anchorage point recom-

, until the belt tension indicator

and lay it over

directly in front of

into the insertion aids

must be visible on

to make sure that the two

is tight.

8. LOOSEN THE SHOULDER STRAPS

To loosen the shoulder straps, press the adjustment button

while at the same time pulling both shoulder straps 08

forward.

CAUTION! Do not pull the shoulder cushions

9. OPEN THE HARNESS BUCKLE

To open the harness buckle

buckle.

10. SET THE CHILD IN THE CHILD SEAT

Place your child in the child seat. Check that the harness buckle

11. PLACE THE SHOULDER STRAPS

Pass the shoulder straps

WARNING! Do not twist or swap the shoulder straps, as this

will remove their protective function.

12. FASTENING THE HARNESS BUCKLE

Take the two buckle clips

inserting them in the harness buckle audible click when inserted.

13. TIGHTENING THE ADJUSTMENT STRAP

Pull the adjustment strap

around your child’s body.

WARNING! The hip belts must be positioned aslowas possi-

ble across your child's hips.

press the red button onthe

is facing forwards.

over your child’s shoulders.

and hold them together before

– they must make an

until the strap lies ﬂat andsnug

100 - 150 cm

The secured along with your child by the vehicle’s 3-point seat belt.

1. PREPARATORY STEPS

1.1 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.

With car seat belt

ADVANSAFIX M i-SIZE

Before each journey, in order to ensure your child’s safety, make

sure that ...

Źthe child seat is engaged on both sides with the ISOFIX locking arms

intheISOFIX ﬁxing points

Źthe child seat is securely fastened; Źthe top tether

indicator

Źthe child seat belts ﬁt snugly around the child’s body without causing constriction; Źthe shoulder straps Źthe shoulder cushions Źboth buckle clips

is tight over the backrest of the car seat and the belt tension

is green;

and that both locking buttons 05 are fully green;

are correctly adjusted and are not twisted;

are in the correct position for your child’s body;

are fully engaged in the harness buckle 20;

100 - 150 cm

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 4.1 “PREPARING ISOFIX”.

1.2 Follow the steps in Section 4.3 “ADJUSTING THE HEADREST (100 - 150 cm)”.

With ISOFIX + car seat belt

6. ADJUSTING THE SEAT ANGLE

The seat shell of the positions. The

Seat angle Body height

Upright position 76 - 140 cm

4. PRESSING THE CHILD SEAT BACKWARDS

Push the child seat ﬁrmly backwards as far as it will go.

5. CHECKING FOR CORRECT FASTENING

Shake the child seat to check that it is securely fastened

and check the locking buttons indicators are fully green.

6. Follow the steps in Section 7 “SECURING YOUR CHILD”.

is not permanently installed in the vehicle. It is simply

2. Place the child seat on the car seat. Ensure that the back-

is ﬂat against the backrest of the car seat.

rest

Tip! If the headrest of the car seat prevents the child seat

from being fastened properly, it should be removed (see

vehicle’s instruction manual). Secure the removed headrest in a suitable place in the vehicle so that it will not be tossed around.

3. Follow the steps in Section 7 “SECURING YOUR CHILD”.

ADVANSAFIX M i-SIZE

FDQEHXVHGLQWKUHHGLႇHUHQWUHFOLQHG

is approved for use as follows:

to make sure that the two

7. SECURING YOUR CHILD

1. Sit your child in the child seat. Pullout the car seat belt, pass it in front of your child and into the car seat belt buckle

DANGER! Check that the car seat belt is not twisted,

otherwise the full protective action of the restraint system will be impaired.

2. Insert the buckle clip in the car seat belt buckle is an audible click.

3. Pass the diagonal belt belt buckle side seat cushion.

DANGER! The car’s seatbelt buckle

the dark green belt guide

4. Also pass the lap belt ion into the dark green belt guide

DANGER! The lap belt

ble over your child’s hips on both sides.

5. Pass the lap belt

DANGER! Do not pass the diagonal belt

green SecureGuard

6. Pass the diagonal belt

at the headrest 07 so that it is fully in the belt holder 29

without twisting.

Tip! If the backrest

holder diagonal belt adjust the headrest

7. Make sure that the diagonal belt bone, not the neck, of your child and that the button on the dark green belt holder is

Tip: You can adjust the height of the headrest

the vehicle.

DANGER! The diagonal belt

wards. You can adjust the belt routing with the adjustable belt deﬂector in the vehicle.

DANGER! The diagonal belt

towards the belt deﬂector on the vehicle. In this case, use the child seat on the back seat only.

8. Tighten the car seat belt by pulling on the diagonal belt

into the dark green belt guide 28 on the

into the dark green SecureGuard 26.

, you can adjust the headrest

can then be easily inserted. You can then

until there

and lap belt 25 on the car’s seat-

on the other side of the seat cush-

must be placed as low as possi-

into the light green belt holder

is covering the light green belt

back to the correct height.

fully closed.

must not be near

into the dark

upwards. The

passes over the collar-

again in

must run diagonally back-

must never run forwards

Middle position 76 - 150 cm

2. Place the child seat facing forward on an approved car seat.

Make sure that the backrest the car seat.

Tip! If the headrest of the car seat prevents the child seat

from being fastened properly, it should be removed (see vehicle’s instruction manual). Secure the removed headrest in a suitable place in the vehicle so that it will not be tossed around.

3. FASTENING THE ISOFIX

3.1 Position the two ISOFIX locking arms

the two insertion aids

3.2 Push the two ISOFIX locking arms

until the ISOFIX locking arms 04 engage on both sides

with an audible click.

DANGER! The green locking button

both sides indicating that the child seat is correctly fastened.

is ﬂush with the backrest of

directly in front of

into the insertion aids

must be visible on

Lying position 76 - 150 cm

To adjust the seat angle:

Pull the adjustment handle

the seat pan

DANGER! The seat pan

whatever the position. Pull on the seat pan 24 to check that it has engaged.

TIP! You can adjust the tilt angle of the child seat

while your child is sitting on it. Tighten the vehicle seat belt after adjusting the seat angle if you use the child seat with the vehicle seat belt (

into the desired position.

forwards and push/slide

PXVWEH¿UPO\HQJDJHG

B1 and B2).

even

Before every journey, for your child’s safety, check that ...

Źthe child seat is engaged on both sides with the ISOFIX locking arms in the

ISOFIX ﬁxing points and both locking buttons are fully green (only applies to

with ISOFIX and car seat belt);

Źthe child seat is securely fastened; Źthe lap belt is passed through the dark green belt guides on both sides of the

seat cushion,

Źthe

lap belt is passed through the dark green

Źthe diagonal belt on the car’s seat belt buckle side is also passed through the

dark green belt guide on the seat cushion,

Źthe diagonal belt is passed through the light green belt holder at the headrest,

SecureGuard.

B1 |

Źthe diagonal belt runs diagonally backward, Źthe straps are tight and not twisted, Źthe car’s seat belt buckle is not placed in the dark green belt guide on the seat

cushion.

DANGER! diagonal belt ately, or as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

If your child tries to open the car’s seat belt buckle

in the dark green SecureGuard 26, stop your vehicle immedi-

or insert the

8. REMOVING THE CHILD SEAT

8.1 UNFASTENING YOUR CHILD:

A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER) To unfasten your child, press the red button on the buckle.

B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)

To unfasten your child, use the release button of your car seat buckle.

8.2 REMOVAL:

DANGER! Remove the child seat from the vehicle. Never carry the child seat in

the car if it is not fastened properly.

A) 76 - 102 cm / ≤ 21 kg (ISOFIX + TOP TETHER)

1. Loosen the top tether

2. Release the snap-on hook

top tether

3. Loosen the ISOFIX fastening on both sides by squeezing the green locking button

4. Pull the seat forward and store the top tether attach the snap-on hook of the top tether child seat.

5. Move the ISOFIX locking arms

B) 100 - 150 cm (ISOFIX + CAR SEAT BELT / CAR SEAT BELT)

1. Press the release button on your car seat buckle

2. Open the light green belt holder

backwards, then pull out the diagonal belt

Only for installation method with ISOFIX:

3. To release the ISOFIX ﬁtting, squeeze the green locking button button

4. Move the ISOFIX locking arms

to the front over the child seat.

and red release button 06 together.

together, ﬁrst on one side then on the other.

by pushing the metal tongue

from the anchorage point in the vehicle and lay the

to the fastening on the back of the

back into the seat pan 24.

by pressing the button on the belt holder 29

back into the seat pan 24.

away from the belt.

in the storage pouch 14 and

and red release

Britax Romer Advansafix M i-Size User guide

Specifications and Main Features

Frequently Asked Questions

User Manual