Britax Romer Advansafix III SICT User guide

Download

Page 1

A correctly adjusted headrest

ensures optimal protection for your child in the safety seat: The headrest

must be adjusted so that the shoulder belts

are at the same level as your child’s shoulders.

CAUTION! The shoulder belts

must not run behind the

back of the child or at ear height or above the ears.

The shoulder belts are adjusted as follows:

1. Loosen the 5-point harness

of the child seat as much

as possible.

Back side of the child seat:

2. Press the button of the shoulder belt height adjuster

at the rear of the seat shell and tilt the shoulder belt height adjuster

towards you.

3. Slide the shoulder belt height adjuster

to select the

correct height of the shoulder belts

and engage it in the

positon that ﬁts for your child by releasing the button.

A correctly adjusted headrest

ensures that the diagonal

seat belt section

is optimally positioned, and gives your child the optimal protection. The headrest

must be adjusted so that there is a space

two ﬁngers wide between the headrest

and your child‘s

shoulders.

To adjust the height of the headrest to ﬁt your child:

1. Squeeze the adjustment handle

on the back of the

headrest

This unlocks the headrest.

2. You can now move the unlocked headrest

to the desired height. As soon as you release the adjustment handle

the headrest

will lock into place.

3. Place the child seat on the vehicle seat.

4. Have your child sit down in the child seat and check the

height. Repeat this process until the headrest

07 is at

the optimal height. If in the lowest position the headrest

is still too high, additional adjustment can be made

through the shoulder belt height adjuster

, as explained

in section 5.2

5.3. Adjusting the headrest in vehicle belt installation

1. If your vehicle is not equipped with the ISOFIX insert guides as standard, clip the two insert guides

which are included with the seat* with the cut-out facing upwards onto the two ISOFIX attachment points

of your vehicle. TIP: The ISOFIX attachment points are located between the surface and the backrest of the vehicle seat.

2. Move the head restraint on the vehicle seat to the upper

position.

3. Pull the grey fabric loop

to pull out both locking arms

until you hear a click sound which indicates they are

fully engaged.

4. On both sides of the seat squeeze the green safety button

and the red release button 05 together and remove

the connector protection

* The insert guides make it easier to install the child safety seat with the aid of the ISOFIX attachment points and prevent damage to the seat covering. When not in use, they should be removed and stored in a safe place. On vehicles with a folding backrest the insert guides must be removed before the backrest is folded. Any problems which occur are usually caused by dirt or foreign objects on the insert guides and on the hooks. Clean o any dirt or foreign objects to remedy this type of problem.

5. PREPARATORY WORK

5.1 Prepare ISOFIX

5.2 Adjusting the headrest in 5-point harness installation

Please read the chapter with your desired installation method in chapter 6 ﬁrst.

For the safety of your child, before every journey in the car check that...

►the child safety seat is engaged on both sides with the ISOFIT locking arms

in the

ISOFIX attachment points

and that both green safety buttons 04 are completely green;

►the child seat is ﬁrmly installed in the vehicle; ►the SICT

is correctly installed and used.

►the Top Tether

is tightly tensioned over the backrest of the car seat and the tension

indicator

is green;

►the straps of the child safety seat are close to the body without constricting the child; ►the shoulder belts

are correctly adjusted and the straps are not twisted;

►the shoulder pads

are at the same level as your child´s shoulders;

►the buckle latches

are engaged in the harness buckle

;

Caution: If your child attempts to open the green safety buttons

or the harness

buckle

, make sure to stop at the earliest opportunity. Check that the child safety seat is correctly attached and make sure that your child is properly secured. Teach your child about the dangers involved.

6. Grasp the child seat with both hands and slide the two locking arms

ﬁrmly into the insert guides 02 until the locking arms engage with a clicking noise on both sides. The green safety button

must now be visible on both

sides. CAUTION! The locking arms are only correctly engaged if

both of the safety buttons

are completely green.

1. Make sure that the child seats 5-point harness is removed and the SecureGuard is installed correctly (see section 09)

2. Follow the steps in section 5.1

3. Follow the steps in section 5.3

4. Make sure the Top Tether

lies over the child seat. If not,

take the Top Tether

from the storage bag

and lay it

over the child seat.

5. Place the child seat facing in the direction of travel on the vehicle seat.

7. Push the child seat towards the backrest applying ﬁrm, even pressure on both sides.

8. Shake the child safety seat to make sure it is safely attached and re-check to the green safety buttons

to make sure

that both of them are completely green

13. Have your child sit down in the child seat.

14. Pull out the vehicle seat belt and guide it in front of your child

to the vehicle seat buckle

CAUTION! Do not twist the belt.

15. Engage the buckle tongue in the vehicle seat buckle

CLICK!

16. Place the diagonal seat belt section

and lap belt section

on the side of the vehicle seat belt buckle 29 under the

armrest and into the light red belt guide

of the child seat.

CAUTION! The vehicle seat belt buckle

must not be

positioned between the light red belt guide

and the armrest.

17. Place the lap belt

in the light red SecureGuard 46 .

CAUTION! Do not place the diagonal seat belt section

in the light red SecureGuard

18. Place the lap belt section

on the other side of the child

seat in the light red belt guide

CAUTION! The lap belt section

must lie as low as

possible over your child‘s hips on both sides

19. Guide the diagonal seat belt section

into the dark red

belt holder

of the headrest 07 until it lies completely in

the belt holder

and is not twisted.

Tip! If the backrest

conceals the belt holder 30, you can

adjust the headrest

upwards. The diagonal seat belt section

can now be easily inserted. Now return the headrest 07 to

the proper height, as in Section 5.3.

20. Make sure that the diagonal seat belt section

runs over your child‘s shoulder bone, and not in front of his or her neck.

Tip! You can still adjust the height of the headrest

again here

in the vehicle.

CAUTION! The diagonal seat belt section

must run diagonally backward. You can adjust the course of the belt with your vehicle‘s adjustable belt deﬂector.

CAUTION! The diagonal seat belt section

must never lead forward to the vehicle‘s belt deﬂector. In this case, only use the child seat on the rear seat.

For the safety of your child, before every journey in the car check that...

► the child safety seat is engaged on both sides with the ISOFIT locking arms

in the

ISOFIT attachment points

and that both green safety buttons 04 are completely green;

►the child safety seat is securely fastened; ►the SICT

is correctly installed and used.

►the Top Tether

is tightly tensioned over the backrest of the car seat and the ten-

sion indicator

is green;

►the lap belt section

runs through the light red belt guides 23 on both sides of the

seat cushion;

►the lap belt section

runs through the light red SecureGuard 46 .

►the diagonal seat belt section

on the side of the vehicle seat belt buckle 29 also

runs through the light red belt guide

of the seat cushion;

►the diagonal seat belt section

runs through the dark red belt holder 30 of the

headrest;

►the diagonal seat belt section

runs diagonally backward,

►the straps are tight and not twisted; ►the vehicle seat belt buckle

is not positioned between the light red belt guide

and the armrest of the seat cushion.

CAUTION! If your child attempts to open the safety buttons

or the harness

buckle

or is trying to put the diagonal seat belt section 11 in the light red

SecureGuard

, make sure to stop at the earliest opportunity. Check that the child safety seat is correctly attached and make sure that your child is properly secured. Teach your child about the dangers involved.

GROUP 2 (15-25 kg) & GROUP 3 (22-36 kg)

With ISOFIT + Top Tether + Vehicle belt

To remove the child seat follow the steps in section 8

7. Push the child seat towards the backrest applying ﬁrm, even pressure on both sides.

8. Shake the child safety seat to make sure it is safely attached and re-check the green safety buttons

to make sure

that both of them are completely green.

6. Grasp the child seat with both hands and slide the two locking arms

ﬁrmly into the insert guides 02 until the locking arms engage with a clicking noise on both sides. The green safety button

must now be visible on both sides.

CAUTION! The locking arms are only correctly engaged if

both of the safety buttons

are completely green.

1. Make sure that the child seat´s 5-point harness is installed correctly and the SecureGuard is NOT installed (see section

10).

2. Follow the steps in section 5.1

3. Follow the steps in section 5.2

4. Make sure the Top Tether 13 lies over the child seat. If not,

take the Top Tether

from the storage bag

and lay it

over the child seat.

5. Place the child seat facing in the direction of travel on the vehicle seat.

GROUP 1 (9-18 kg)

With ISOFIX + Top Tether + 5-Point Harness

6. INSTALLATION

9. Take the Top Tether

and press the metal tongue

away from the strap to lengthen the strap and pull the Top Tether

by the snap hook 17 until it makes a V-shape.

10. Route the Top Tether

on the left and right hand sides of

the vehicle headrest.

11. Hook the snap hook

into the Top Tether anchoring point

recommended in your vehicle owner‘s guide.

CAUTION! Be sure not to use the luggage hook instead of

the Top Tether point. Check your vehicle and look for this

sign:

12. To Tension the Top Tether

remove the slack by pulling

the free end of the belt through the metal tongue

, equalising the strap tension on both sides. The Top Tether is correctly tensioned when the green tension indicator

is extended by 1 cm.

13. Follow the steps in section securing your child with 5-point harness.

14. Press the SICT

into both SICT fastening points B on the side of the child seat nearest the vehicle door and clip in the SICT

CAUTION! Make sure that there is a gap of approximately

5 mm between the SICT

and the vehicle door in order to avoid pressure marks and other damage to the door trim.

SECURING YOUR CHILD WITH 5-POINT HARNESS

7. CARE INSTRUCTIONS

To ensure the full protective eect of the child safety seat:

►In the event of an accident with an impact speed above 10 km/h it is possible that the

child safety seat may have been damaged, but that the damage may not be immediately obvious. In this case the child safety seat must be replaced. Please dispose of it properly.

►Regularly check all important parts for damage. Make sure that the mechanical com-

ponents in particular are all in perfect working order.

►To prevent damage, ensure that the child safety seat does not become jammed

between hard objects (car door, seat runners etc.).

►Always have the child safety seat checked if it has been damaged (e.g. if it is

dropped).

►Never lubricate or oil parts of the child seat. ►In order to properly protect your baby, it is imperative that you install and use the

ADVANSAFIX IIII SICT exactly as described in this manual.

Disposal of packaging Container for cardboard

Cover Residual waste, thermal utilisation

Plastic parts In accordance with the labelling in the designated container

Metal parts Container for metals

Harness straps Container for polyester

Buckle & latch Residual waste

8. REMOVAL OF THE CHILD SEAT

CAUTION! Remove the child seat from the vehicle. The child seat must never be

transported in the car if it is not properly secured.

Detach/Reattach SICT

To detach the SICT

, press both SICT fastening points B and remove the SICT A.

The SICT

can now be reattached to the product.

Group 1 (ISOFIT & Top Tether)

1. To release the ISOFIT fastening, squeeze the green safety button and the red release button together,ﬁrst on one side, then on the other.

2. To release the TopTether anchoring loosen the belt by lifting the metal tongue of the adjuster away from the belt. Then take the spring hook out of the anchoring point.

3. Slide the ISOFIT locking arms back into the seat shell and put the connector protection on the ISOFIX.

Group 2 and Group 3 (ISOFIT & Top Tether)

1. Release vehicle seat buckle if securing the child seat.

2. To release the ISOFIT fastening, squeeze the green safety button and the red

release button together,ﬁrst on one side, then on the other.

3. To release the TopTether anchoring loosen the belt by lifting the metal tongue of the

adjuster away from the belt. Then take the spring hook out of the anchoring point.

4. Slide the ISOFIT locking arms back into the seat shell and put the connector protec-

tion on the ISOFIX.

4. Make sure that your child´s back lies ﬂat against the backrest of the child seat.

5. Guide the two buckle latches

together and engage them before putting them into the harness buckle

- this should

make a click noise.

6. Pull shoulder straps

to remove all slack from the lap

section ensuring the harness lies ﬂat.

7. Pull on the adjuster strap

until the harness lies ﬂat and is

close against your child‘s body.

CAUTION! Pull the adjuster strap

straight (not up-

wards or downwards).

CAUTION! The harness straps

must be positioned as

low as possible over your child‘s hips.

8. Pull down on the shoulder pads

to ensure they are cor-

rectly positioned.

1. Open the harness buckle

(press red button)

2. Press the adjusting button

and at the same time pull both

shoulder belts

forwards. Do not pull on the shoulder pads

3. Have your child sit down in the child seat.

The more snugly the harness ﬁts over your child‘s body, the better your child will be protected. Therefore avoid putting thick clothes on your child under the belt.

To remove the child seat follow the steps in section 8

9. Take the Top Tether

and press the metal tongue 16 away

from the strap to lengthen the strap and pull the Top Tether

by the snap hook 17 until it makes a V-shape.

10. Route the Top Tether

on the left and right hand sides of

the vehicle headrest.

11. Hook the snap hook

into the Top Tether anchoring point

recommended in your vehicle owner‘s guide.

CAUTION! Be sure not to use the luggage hook instead of

the Top Tether point. Check your vehicle and look for this

sign:

12. To Tension the Top Tether

remove the slack by pulling the

free end of the belt through the metal tongue

, equalising the strap tension on both sides. The Top Tether is correctly tensioned when the green tension indicator

is extended

by 1 cm.

1 cm

0405

21. Tighten the vehicle seat belt by pulling on the diagonal seat belt section

22. Press the SICT

into both SICT fastening points B on the side of the child seat nearest the vehicle door and clip in the SICT

CAUTION! Make sure that there is a gap of approximately 5

mm between the SICT

and the vehicle door in order to avoid pressure marks and other damage to the door trim.

1 cm

Page 2

4. CARE AND MAINTENANCE

Care for the harness buckle

It is vital for the safety of your child that the harness buckle works correctly. Malfunctions of the harness buckle are usually caused by accumulations of dirt or foreign bodies. Malfunctions are as follows:

• The buckle latches are ejected only slowly when the red release button is pressed.

• The buckle latches will no longer lock home (i.e. they are ejected again if you try to push them in).

• The buckle latches engage without an audible „click“.

• The buckle latches are dicult to insert (you feel resistance).

• The buckle only opens if extreme force is applied.

Remedy

wash out the harness buckle so that it functions properly once again:

Cleaning the harness buckle

1. Open the harness buckle

(press the red button).

2. Open the Velcro fastener on the crotch pad

and take o the crotch pad from the

cover.

3. Put the seat shell into the recline position

4. Grasp the metal plate

from underneath and turn it into a vertical position

5. Slide the metal plate

through the slot 34

6. Remove the harness buckle

7. Soak the harness buckle

in warm water with washing-up liquid for at least an

hour

8. Then rinse and dry it thoroughly.

Cleaning

CAUTION Please be sure to use only genuine Britax replacement seat covers, as

the seat cover is an integral part of the child safety seat which plays an important role in ensuring that the system works properly. Replacement seat covers are available from

your retailer.

CAUTION! The child seat must not be used without its cover.

• The cover can be removed and washed with a mild detergent using the washing machine‘s cycle for delicate items (30 °C). Please observe the instructions on the washing label of the cover.

• The plastic parts (including the SecureGuard) can be cleaned using soapy water. Do not use harsh cleaning agents (such as solvents).

• The harnesses can be washed in lukewarm soapy water.

CAUTION! Never remove the buckle latches

from the straps.

• The shoulder pads can be washed in lukewarm soapy water.

Removing the cover

A) Headrest

1. Move the headrest of the child seat to the upper position.

2. Take the elastic seam of the cover

from the hooks at the back side of the headrest

and remove the cover of the headrest.

B) Cover

1. Undo the hooks on the bottom side.

2. Undo the hooks located on the upper back side.

3. Undo the elastic loop on both sides of the belt guides.

4. Open the two plastic fasteners on the back side of the cover.

5. Remove the cover.

Re-ﬁtting the Cover:

Simply follow the steps in the opposite order.

CAUTION! Never use the child seat in installation method A without a correct

installed buckle. Make sure that the metal plate

is correctly attached.

CAUTION! Check that the harness straps are not twisted and that they

have been correctly inserted in the belt slots on the cover.

2. USE IN THE VEHICLE

Please observe the instructions on the use of child restraint systems described in your vehicle owner’s manual.

The seat may be used in vehicles equipped with ISOFIX, Top Tether anchoring systems and 3-point belt (see type list). Please consult your vehicle owner’s manual for information about the ISOFIX &Top Tether anchoring points and the installation with 3-point belt. Also check your vehicle owner’s manual for seats which are approved for child safety seats in the weight classes 9-18 kg, 15-25 kg, 22-36 kg.

You can use your child car seat as follows:

In the direction of travel Ye s

Against the direction of travel

with 2-point belt (Vehicle belt)

On seats featuring: ISOFIX attachments (between seat surface and back-

rest), Top Tether anchoring points (for example on the parcel shelf, on the ﬂoor or behind the backrest) and 3-point belt (Vehicle belt)

Yes

2) 3)

(Please observe the applicable regulations in your country)

1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only if the vehicle seat is also approved for use by adults. The seat must not be positioned anywhere where it is in range of an airbag which is being deployed.

2) The safety belt must be approved to ECE R 16 or a comparable standard (see test label on belt with an “E” or “e” in a circle).

3) If there is a front airbag: Slide the passenger seat a long way back and refer to any instructions in vehicle owner’s manual.

1. GENERAL SAFETY NOTES

Take the time to carefully read through these instructions, and always

keep them ready to hand in the designated pocket on the child seat.

For the protection of all vehicle occupants

In the case of an emergency stop or an accident, persons or objects which are not properly secured in the car can cause injury to other vehicle occupants. For this reason, please always check that:

• the backrests of the vehicle seats are locked (e.g. that the latch on a folding rear seat bench is engaged).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are secured.

• all persons in the vehicle have their seat belts fastened.

• the child safety seat is always secured in the car via the ISOFIX anchoring, the Top Tether, even when there is no child in the seat.

For the protection of your child

• The more snugly the harness ﬁts over your child‘s body, the safer your child

will be.

• Please do not ever leave your child unattended in the child safety seat in the

vehicle.

• Use on the rear seat:

Move the front seat forward far enough that you child‘s feet cannot hit the backrest of the front seat (to prevent risk of injury).

• The child safety seat can get hot in direct sunshine. Caution: Children‘s

skin is delicate and could be injured as a result. Protect the child seat against intensive direct sunlight when it is not currently in use.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Make stops during longer journeys to give your child an opportunity to run

about and play.

To protect your vehicle

Some vehicle seat coverings made of more delicate materials (e.g. velour, leather, etc.) may develop wear marks when child seats are used. For optimum protection of your seat covers, we recommend using the BRITAX Car Seat Protector, which is available from our range of accessories.

3. APPROVAL

BRITAX

child safety seat

Tested and certiﬁed according

to ECE* R 44/04

Group Body weight

ADVANSAFIX III SICT 1 9 to 18 kg

2 15 to 25 kg

3 22 to 36 kg

*ECE = European Standard for Child Safety Equipment

The child safety seat has been designed, tested and certiﬁed according to the requirements of the European Standard for Child Safety Equipment (ECE R 44/04). The test mark E (in a circle) and the certiﬁcation number are located on the orange certiﬁcation sticker (sticker on the child safety seat).

• This certiﬁcation will be invalidated if you make any modiﬁcations to the child safety seat.

• The ADVANSAFIX III SICT child safety seat must only be used to secure your child in the vehicle. It must never be used as a seat or toy in the home.

Risk of injury due to unauthorised modiﬁcations!

Unauthorised technical modiﬁcations may reduce or entirely void the seat’s protective properties.

• Do not make any technical modiﬁcations to the child seat.

• Use the child seat only as described in these user instructions.

The ADVANSAFIX III SICT is approved for three methods of installation:

Group Installation method Child installation User Guide

chapter

1 (9-18 kg) ISOFIX + TopTether with 5-point harness A

2 (15-25 kg) ISOFIT + TopTether

Vehicle belt B

3 (22-36 kg) ISOFIT + TopTether

Vehicle belt B

4. Squeeze the adjustment handle

at the rear of the headrest 07 and push the head-

rest into the lowest position.

5. Release the adjustment handle

to lock into place.

6. Lift the lower part of the headrest cover and place it over the headrest

7. Open the left and right buttons on the lower part of the cover

and lay the cover

piece on the seating area.

8. Take the shoulder belts

and the buckle latches 20 from the storage compartment

and unroll the shoulder belts.

9. Fold back the two cover pieces and close the left and right poppers

on the lower

part of the cover.

Should the child seat not be in the most reclined position: Press the recline handle so that the seat is in its most upright position.

10. Lift the harness buckle

and the shoulder pads 19 from the storage bag 14 on

the back side of the seat.

11. Reﬁtting harness buckle

and crotch pad 32: pull the elastic strip 44 in the seat-

ing area towards you. Use the belt slot closest to the backrest

12. Take the harness buckle

and hold the metal plate 33 vertically. Push it with the

narrow side upwards through the belt slot

to the seat shell from above.

13. Ensure by looking underneath the seat that the metal plate

is in a horizontal posi-

tion and check the installation by pulling on the harness buckle

several times.

14. Guide the two buckle latches

together and engage them before putting them

into the harness buckle

- this should make a click noise.

CAUTION! The lap belts must not be twisted or swapped.

15. Thread the shoulder pads

onto the shoulder belts 08 in the correct orientation

as shown ensuring there are no twists. Align the two loops of the shoulder belts

and strap loops of the shoulder pads

16. Pull the shoulder belts

and the strap loops of the shoulder pads 19 through the

slots

. Make sure that the shoulder belts 08 and the strap loops run through the

slots of the seat shell as well as the slots of the shoulder belt height adjuster

Tip: Fold up the rear cover part.

17. Pull the strap loops of the shoulder pads

onto the plastic extensions 41 of the

shoulder belt height adjuster

.Tip: the strap loops of the shoulder pads should

be the lower loop.

18. Fold the upper part of the cover downwards.

CAUTION! The shoulder belts

must not be twisted or swapped

19. Take the connecting piece

from the provided storage on the back side of the

child seat.

20. Hook the shoulder belts

back onto the connecting piece 39. The left loop on

the left arm of the connecting piece and the right loop on the right arm.

21. Pull slowly on the adjustment strap

and at the same time push the connecting

piece

between backrest and the provided storage of the connecting piece.

1. Put the storage bag

forward over the seat.

2. Loosen the 5-point harness

of the child seat as much as possible.

Back side of the child seat:

3. Press the button of the shoulder belt height adjuster

at the rear of the seat shell

and tilt the shoulder belt height adjuster

towards you.

4. Move the shoulder belt height adjuster

into the top position and ﬁx the position

by releasing the button of the shoulder belt height adjuster.

5. Loosen the 5-point harness

of the child seat as much as possible. Unhook the

shoulder belts

on the back side of the child seat from the connecting piece 39 .

6. Snap the connecting piece

in the provided storage.

7. Pull below both, the shoulder pads

and the two shoulder belts 08 to the front

through the slots

(front side of the child seat).

8. Slide the belt loops o of the plastic extensions

of the shoulder belt height adjust-

Front side of the child seat:

9. Pull out the adjuster strap

as far as possible.

10. Store the adjuster strap in the adjuster housing

11. Pull the shoulder pads

through the slots 40 to the front.

12. Remove the shoulder pads

from the shoulder belts 08 and put them in the

storage bag on the rear of the seat.

13. Open the harness buckle

(press the red release button)

14. Lift the lower part of the rear cover to the top and place it over the headrest.

15. Open the left and right poppers

on the lower part of the cover 43 and lift the

cover piece to the front. Slide the buckle latches

down into the storage compart-

ments.

16. Roll the shoulder belts

together and place them also into the storage compart-

ments.

17. Repositon the two cover parts to the rear and lock the poppers

on the left and

right side of the cover back side.

18. Lift the recline handle and pull at the front to fully recline the child seat.

19. Pull the elastic strip

over the harness buckle 21.

20. Grasp the metal plate

from underneath and turn it into a vertical position.

21. Push upwards and slide the metal plate

through the slot 34.

22. Remove the harness buckle

with the crotch pad 32 and store it in the storage

bag

09. REMOVING THE 5-POINT HARNESS& & REFITTING THE SECUREGUARD

10. REFITTING THE 5-POINT HARNESS & REMOVING THE SECUREGUARD

BRITAX RÖMER Kindersicherheit GmbH Blaubeurer Straße 71 D-89077 Ulm Germany

t: +49 (0) 731 9345-199/-299 f: +49 (0) 731 9345-210 e: service.de@britax.com www.britax.com

BRITAX EXCELSIOR LIMITED 1 Churchill Way West Andover Hampshire SP10 3UW United Kingdom

t: +44 (0) 1264 333343 f: +44 (0) 1264 334146 e: service.uk@britax.com www.britax.com

9 – 36 kg 9 m ~ 12 y

www.britax.com

2000026067 16/06

User instructions

ADVANSAFIX III SICT

23. Take the SecureGuard

from the storage bag and hold the metal plate 47

vertically. Push it with the narrow side upwards through the belt slot

closest to

you into the seat shell from above.

24. Ensure by looking underneath the seat that the SecureGuard metal plate

is in

a horizontal position and check the installation by pulling on the SecureGuard

several times.

1. Grasp the SecureGuard metal plate

from underneath and turn it into a vertical

position.

2. Push upwards and slide the metal plate

through the slot 34.

3. Remove the SecureGuard

and store it in the storage bag 14.

Britax Romer Advansafix III SICT User guide

Specifications and Main Features

Frequently Asked Questions

User Manual