12
WEEKENDER
3 in 1 Portable Cot
series R032S
4001054
KEEP INSTRUCTIONS IN SAFE PLACE FOR FUTURE REFERENCE
Distributed by:
AUSTRALIA
BRITAX CHILDCARE PTY.LTD.
A Britax International company.
(Incorporated in Victoria)
A.B.N. 55 006 773 600
99 Derby Road, Sunshine,
Victoria 3020, Australia
Phone: (03) 9288 7288
Fax: (03) 9311 5798
Due to our continuing program of development, Britax reserves the right to alter the specifications,
colour or design without any further notice.
The Steelcraft trademark is the property of Britax Childcare Pty. Ltd-Australia.
The Britax trademark is the property of Britax Excelsior Limited - UK.
Visit the Britax website at: http:/www.britax.com.au or email us at custserv@britax.com.au
Due to the variations in the style and design of our products the illustrations used in this instruction
booklet are generic.
12/06 c 2007 Copyright Britax Childcare Pty. Ltd. Australia.
NEW ZEALAND
BRITAX CHILDCARE NZ. Limited.
A Britax International company.
101 Diana Drive, Glenfield,
Auckland 9, New Zealand.
Phone: (09) 443 0102
Fax: (09) 443 0120
Each Steelcraft unit is thoroughly inspected in our Quality Assurance
department prior to delivery. In the unlikely case that you find any
material or workmanship that affects the units normal operation,
we will repair the unit free of charge within 12 months of purchase.
You are required to present your receipt as proof of purchase.
For all concerns with your product please contact our Customer
Service team.
CUSTOMER SERVICE
1300 303 330 - Australia
0508 688 822 - New Zealand
Please read all the information carefully before using this product.
This warranty does not apply to failure due to improper care,
or normal wear and tear caused by product use. We reserve the
right to inspect the unit. You may be charged for repairs if the product
has been damaged accidentally.
Warranty
02
BEFORE ASSEMBLING THIS COT READ AND UNDERSTAND THE INSTRUCTIONS.
INCORRECT ASSEMBLY MAY MAKE THE COT UNSAFE. KEEP THESE INSTRUCTIONS IN A
SAFE PLACE FOR FUTURE REFERENCE.
WARNINGS
.
Never leave your child unattended.
.
Do not use your cot if any part is broken, torn or missing.
.
Do not use or leave the cot near open fires, naked flames, electric bar fires, gas fires,
stoves, heaters or barbecues.
.
Do not place the cot where your child could reach medication, money, string, elastic,
small toys or other small objects.
.
Do not place the cot near trailing cords, leads or flexes such as cords or electrical
leads, etc.
.
Do not use additional mattress or padding.
.
Do not place toys or other objects in the cot which could provide a step or foothold to help
the child climb out.
.
Cots with padded rails should not be used if the covered fabric is torn or bitten through.
.
Do not use parts or accessories except those tested and approved by Steelcraft.
.
Always check that the folding parts are fully locked before using the cot.
.
Do not place more than one child in the cot at the same time.
.
Do not use this cot with a child who can climb out, weighs more than 15kg, or is taller than
90cms.
.
When using a fitted sheet it must fit the mattress tightly.
.
Check that the assembly of the cot is correct and safe.
.
The thickness of the mattress has been specified to ensure that the distance from the top
of the mattress to the top of the lowest side or end will always be at least 500mm. This will
reduce the risk of children falling out of the cot.
.
Always check parts regularly for tightness of screws, nuts and other fasteners - tighten
if required.
.
Use only the mattress supplied with the cot.
.
Do not use an additional mattress, padding, toys or other objects in the cot which would
help your child fall out.
.
Using the wrong size mattress may create hazardous gaps that could result in suffocation
or could reduce the side height of the cot, which may result in your child falling out
of the cot.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
11
www.britax.com.au
www.britax.com.au
CARE AND MAINTENANCE
To prolong the life of your nursery product keep it clean and do not leave it in the direct
sunlight for extended periods of time.
Removable fabric covers and trims may be cleaned using warm water with a household
soap or a mild detergent. Allow it to dry fully, preferably away from the direct sunlight.
DO NOT DRY CLEAN, OR USE BLEACH.
Do not machine wash, tumble or spin dry, unless the care labelling on the product permits
these methods.
Non removable fabric covers and trims may be cleaned using a damp sponge with soap
or mild detergent. Allow it to dry completely before folding or storing it away.
In some climates the covers and trims may be affected by mould and mildew. To help
prevent this occurring, do not fold or store the product if it is damp or wet. Always store
the product in a well ventilated area.
To maintain the safety of your nursery product, seek prompt repairs for bent, torn, worn
or broken parts. Use only those parts and accessories tested and approved
by Steelcraft.
WARNING: IF THE SIDES DO NOT LATCH FIRMLY OR THERE ARE HOLES IN THE
MESH SIDES, DISCONTINUE USE IMMEDIATELY AND SEEK REPAIR.
TESTED AND APPROVED ACCESSORIES
Mattress by Steelcraft - series R032S
Bassinet by Steelcraft - series R032S
Change Table by Steelcraft - series R032S
10
03
www.britax.com.au www.britax.com.au
This cot is made for a mattress which is 740mm wide,
1000mm long and no more than 25mm thick. Using the
wrong size mattress may create hazardous gaps that
could result in suffocation or could reduce the side height
of the cot which may result in your child falling out from
the cot.
For its correct use, ensure you follow these instructions in
the order that they are written.
PARTS LIST
A 1 - Carry bag
B 1 - Mattress
C 4 - Mattress Support Rods
D 1 - Cot
E 1 - Bassinette
F 1 - Change Table
WARNING - MATTRESS SIZE
A
NOTES
B
C
D
E
F
04
09
THESE STEPS WILL ENSURE THAT THE COT IS
CORRECTLY OPENED AND READY FOR USE.
A Unzip the carry bag and remove the cot.
B Stand the cot on its feet and undo the hook & loop
straps that hold the mattress around the frame.
C Remove the mattress and set other accessories aside.
D Separate the legs of the cot.
E Starting with the short rails pull the centre up with
both hands quickly until they are locked in place.
(CAUTION: TAKE CARE, AS FINGER PINCHING CAN
OCCUR IN THE CORNERS WHEN LOCKING THE RAILS
IN PLACE.)
F Now do the same with the longer rails.
NOTE: ALL THE TOP RAILS SHOULD BE LOCKED IN
PLACE. IF THEY ARE NOT, RELEASE THEM AND TRY
AGAIN. THE CENTRE OF THE COT BASE MUST
BE IN A RAISED POSITION TO ALLOW THE RAILS
TO LOCK EASILY. CHECK FOR THE SECURE
ENGAGEMENT OF THE RAILS BY PUSHING DOWN
ON THEM.
G Holding one end of the cot clear of the ground, gently
press down the handle in the middle of the base until
the base lays down flat. The base should now be
locked into position.
1. TO OPEN THE COT
www.britax.com.au www.britax.com.au
A
B
C
D
E
5. TO USE THE CHANGETABLE (con’t)
C Pick the changetable up by the plastic hooks and
connect to the Portable Cot short end rail as shown.
D Rotate the Changetable over the Portable Cot and
engage each of the four clamps onto the side rails.
Move the Bassinette clamps slightly if they interfere
with attaching the Changetable.
NOTE: MAKE SURE THE FOUR CLAMPS ARE ENGAGED
ON TO THE SIDE RAILS.
E Pull the pocket flap over the end of the Portable Cot.
Attach the plastic clamps to the leg tubes to keep the
pocket in place.
F When the Changetable is not in use, always fold over
the end rail until required again.
G To remove the Changetable, release the plastic hooks
from the top rails.
C
D
E
C
G
05
08
1. TO OPEN THE COT (con’t)
H Place the mattress into the cot with its padded side
facing up.
I Secure the mattress to the cot by passing the loop
straps through the slots in the cot base and pressing
it into the hook attachment strips, sewn to the
underside of the cot base.
NOTE: ALWAYS SECURE THE MATTRESS BEFORE
USING THE COT
2. TO USE THE WHEELS
A Push the brake lever down to lock, or lift the brake
lever up to unlock.
NOTE: ALWAYS APPLY THE BRAKES WHEREVER AND
WHENEVER YOU ARE USING THE COT.
(Push down to lock) (Lift up to unlock)
3. TO FOLD THE COT
THESE STEPS MUST BE FOLLOWED IN THIS ORDER
TO EASILY FOLD THE COT.
IF BASSINET OR CHANGE TABLE ARE FITTED, THEY
MUST BE REMOVED BEFORE FOLDING THE COT.
A Release the loop straps under the base that secure
the mattress and remove the mattress from the cot.
www.britax.com.au
www.britax.com.au
4. TO USE THE BASSINET (con’t)
H
I
D Snap the 12 plastic clips onto the top rails of the cot.
Make sure the plastic clips are positioned against the
edge of the corner mouldings.
E Attach the “hook & loop” strips in each corner of
the cot.
NOTE: ALWAYS SECURE THE MATTRESS BEFORE
USING THE BASSINET.
WARNING: TO PREVENT FALLS, THIS BASSINET
SHOULD NOT BE USED ONCE A CHILD CAN SIT UP.
ALWAYS REMOVE THE BASSINET BEFORE FOLDING
THE PORTABLE COT.
5. TO USE THE CHANGETABLE
A
B
D
E
WARNINGS
.
NEVER LEAVE CHILD UNATTENDED.
.
NEVER PLACE A CHILD IN THE PORTABLE COT
WHEN THE CHANGETABLE IS IN USE.
.
ALWAYS USE THE HARNESS WHEN USING THE
CHANGETABLE.
.
ALWAYS FOLD THE CHANGETABLE AWAY WHEN
NOT IN USE.
A Lay the changetable face down with the two plastic
hooks facing up.
B Connect the tubes together on either side of the
changetable. Insert one tube end into the other
until the pin engages. Pull to make sure they are
locked together.
A
06
07
B Pull the strap up in the middle of the base and then pull
base up approximately 50cm.
C Release each top rail by lifting the rail slightly and
squeezing on the buttons, located in the centre joint.
The buttons are located under centre of each rail.
IF THE TOP RAILS DO NOT FOLD - DO NOT FORCE
THEM - LIFT THE BASE HIGHER AND RE SQUEEZE THE
BUTTONS TO FULLY RELEASE THEM.
D Ensure that each rail is fully released and then pull all
the way up on the cot base strap, while gathering the
legs and the frame together until its fully folded.
DISASSEMBLE AND STORE THE BASSINET AND CHANGE
TABLE IN THE CARRY BAG.
E Take the mattress and wrap it around the folded cot
with the padded side facing inwards.
F Thread the straps through the plastic loops,
pull them tight and secure using the hook and
loop attachments.
G Take the carry bag and cover the folded cot.
Finish covering the cot and close the zipper, with the
mattress handle through the opening.
www.britax.com.au
www.britax.com.au
4. TO USE THE BASSINET
A Insert the 2, two-piece support rods into bassinet
inner sleeves separately, then engage them in the
middle by the locking pin.
B Insert the mattress and secure it to the bassinet
by passing the loop straps through the slots in the
bassinet base, then press the loop straps onto the
hook padding, sewn to the underside of the bassinet.
C Lower the bassinet within the cot with warning
label at short end.
3. TO FOLD THE COT (con’t)
C
D
E/F
A
B
A
A
B
C
B
Loading...