Britax Verve User Manual
User Guide
UK
2 Attaching your child seat for use as a travel system
(this vehicle is intended for children from birth and up to 13kgs)
Verve P-Type
adaptor
Verve P-Type
socket
To remove the child
seat move the handle
to the carrying position.
Lift the lever on the
adaptors and lift the
child seat out of the
sockets (dia 2d).
IMPORTANT -
It may be necessary to
remove the adaptors
from the child seat
when installing it in
your vehicle.
If the adaptors are in
contact with the vehicle
seat cushion, remove
them.
To remove the
adaptors from the child
seat, pull the lever on
the adaptors away from
the child seat while
pulling down (dia 2e).
Repeat the process for
both adaptors.
The child seat is
compatible with
the ISOFIX base
(purchased separately).
See www.britax.eu for
further information.
Only use a P-Type child seat on this buggy when tted with a Verve P-Type socket
HANDY HINT -
You may nd it easier
to apply the brake
when tting the child
seat. Please refer to
the user guide for your
buggy.
Clip the socket onto
the chassis from the
inside. Align the bottom
edge of the socket with
the edge shown on
the chassis (dia 2a).
Rotate the xing arm.
Squeeze the housing
and xing arm together
with one hand and
snap over the hook
with the other hand.
Repeat this process for
both sockets.
Ensure that the left
hand and right hand
sockets are used on
the correct side of the
buggy.
To t the adaptor to the
child seat squeeze the
lever and insert into
the space below the
handle (dia 2b). Make
sure it is fully tted and
release the lever to
lock into place. Repeat
this process for both
adaptors.
Ensure that the left
hand and right hand
adaptors are used on
the correct side of the
child seat.
IMPORTANT -
The buggy seat unit
must be removed
before attaching your
car seat.
Lower the child seat
onto the buggy making
sure that the adaptor
on either side drops
into both the sockets on
each side of the buggy
(dia 2c). Push down
rmly. Once the seat is
engaged you will hear
a click.
Move the handle to
the rocking position.
Please refer to the user
guide for the child seat.
WARNING -
Check that the child
seat attachment
devices are correctly
engaged before use.
IMPORTANT -
Ensure your child is
harnessed at all times.
Unclip the hooks on
both sides of the buggy
(dia 1d).
Remove the seat unit
from the chassis by
sliding the base tabs
upwards and out of the
grooves.
Then slide the top tabs
upwards and out of the
grooves until the seat
unit is disengaged
(dia 1e).
To re-t the seat
unit reverse these
instructions.
HANDY HINT -
You may nd it easier
to apply the brake
before removing or
re-tting the seat unit.
Please refer to the user
guide for your buggy for
operation of the brake.
Unfasten the press
studs on the backrest
and unfasten the hook
and loop fastenings on
both sides of the seat
unit where it overlaps
the hood (dia 1a).
HANDY HINT -
You may nd it easier
to stand behind or to
the side of the buggy.
Remove the hood
and bumper bar
by simultaneously
pressing the buttons on
the mouldings on both
sides of the buggy and
slide them upwards
until they disengage
(dia 1b).
Unfasten the hook and
loop fastenings and
press studs shown by
the red circles
(dia 1c).
1 Removing or re-tting your seat unit
(the seat cover must be removed before tting the infant carrier)
B
A
BBO-662-00
A
B
1a 1b 1c 1d
B
B
A
A
1e
2b 2c
2d 2e
2a
1282.000 - Verve Adaptors & Sock1 1 10/1/07 09:15:40
accessories are available from your Britax
stockist or contact Britax Customer Service
Department on 01264 386034. This product
is not intended for commercial use.
Guarantee
All Britax products are carefully designed,
manufactured and tested. However, should
this product prove faulty within six months of
purchase due to a materials or manufacturing
fault please return it to the original place of
purchase. We will then, at our discretion,
either repair it free of charge or replace it with
the same or a similar product.
For guarantee purposes proof of purchase
will be required. We recommend that you
retain your receipt and attach it to this user
guide. They should be kept in a safe place.
Britax does not accept liability for damage
arising from abuse, misuse or negligence.
This guarantee is not transferable and
therefore does not apply to second-hand
products.
Your statutory rights are not affected by
this guarantee.
WARNING – A CHILD’S SAFETY IS YOUR RESPONSIBILITY
Read these instructions carefully before use and keep them for further reference.
Your child’s safety may be affected if you do not follow these instructions.
IMPORTANT!
Please read this User Guide carefully BEFORE trying to use your buggy
Looking after your buggy
The buggy and its cover have been carefully
designed, manufactured and tested to high
safety standards.
Regularly inspect and maintain your buggy to
ensure freedom of movement of the locking
devices and security of components. To
prolong the life of your buggy, keep it clean
and do not leave it in direct sunlight
for extended periods of time.
Helpful hints
Regularly clean and inspect your buggy.
To ensure trouble free operation lubricate
moving parts and joints with a silicon based
spray. If the wheels squeak use a silicon
based spray or light lubricating oil ensuring it
penetrates the wheel and axle assembly.
When using the buggy on the beach, clean it
completely afterwards to remove all the sand
and salt from the mechanisms and wheel
assemblies.
Under certain climate conditions the covers
and trims may be affected by mould and
mildew. To help prevent this occurring, do not
fold or store this buggy if it is wet or damp.
Always store in a well ventilated area.
Cleaning the cover
The hood, seat covers and trims may be
cleaned using warm water with household
soap or mild detergent. Allow it to dry fully,
away from direct sunlight.
DO NOT dry clean or use bleach or any other
aggressive cleaning agents.
To maintain the safety of your buggy, seek
prompt repairs for bent, torn or broken
parts. Use only those parts and accessories
approved by Britax. Replacement parts and
Britax Excelsior Limited
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
A Britax Childcare company
Customer Service Helpline: 01264 386034
Email: helpline@uk.britaxeurope.com
Switchboard: +44 (0) 1264 333343
Fax: +44 (0) 1264 334146
www.britax.eu
WARNING - Ensure that all locking devices are
engaged before use.
WARNING - Children must be harnessed at all
times.
WARNING - Overloading, incorrect folding
and the use of non-approved accessories
may damage or break this buggy and make it
unstable for use.
WARNING - Regularly inspect the buggy to
ensure all parts are in full working order.
WARNING - Any load attached to the handle
affects the stability of the pushchair.
WARNING - This seat is not suitable for
running or skating.
WARNING - It may be dangerous to leave your
child unattended.
DO NOT leave or place your child in a position
where they are exposed to the sun. The canopy
or hood on this product will not give your child
total protection from the harmful rays of the sun.
DO NOT allow the buggy to remain wet for
prolonged periods of time. If it does get wet,
allow to dry unfolded at room temperature.
DO NOT place more that 4kg in the basket.
DO NOT allow children to play with or adjust
the buggy.
DO NOT carry more than one child on this
buggy.
DO NOT use accessories that are not approved
by Britax Excelsior Limited.
DO NOT use a PVC rain cover indoors, in a hot
atmosphere or near a direct heat source - your
child might overheat.
DO read the cleaning instructions for the cover.
DO ensure children are clear of moving parts
and locking devices while making adjustments.
DO periodically check that any screws, nuts,
bolts and other fastenings are fully tightened.
DO store the buggy in a safe place when not
in use. Avoid placing heavy objects on top of it
and do not store near direct heat sources, e.g.
radiators, open bar res or in direct sun light as
the cover may fade.
ALWAYS remove the child from the buggy
before going up or down stairs or escalators.
This buggy is designed and manufactured to
comply to EN1888: 2005.
1282.000 - Verve Adaptors & Sock2 2 10/1/07 09:15:40
Loading...