Britax Kidfix² R Service Manual

1. SAFETY NOTES

Please take the time to read these instructions carefully and keep them to hand in the storage compartment provided on the child safety seat at all times! The instructions must accompany the child seat if it is passed on to athird party!

DANGER! To protect your child:

•

In the event of an accident at acollision speed of more than 10 km/h, the

child seat may be damaged without the damage being immediately visible. In

this case the child seat must be replaced. Please dispose of it properly.

•

Always have your child seat checked if it has been damaged (e.g by falling to

the ground).

•

Regularly check all important parts for damage. In particular, ensure that all

the mechanical parts are fully functional.

•

Never apply oil or grease to any parts of the child seat.

•

Never leave your child unattended on the child seat in the vehicle.

•

Only allow your child to enter and exit the vehicle on the pavement side.

•

Protect the child seat from intense direct sunlight when not in use. The child

seat can become very hot in direct sunshine. Children's skin is sensitive and

could be harmed as aresult.

•

The more snugly the belt ﬁts over your child's body, the better the child

will be protected. Therefore, avoid having your child wear thick clothes un-

der the belt.

•

On long journeys, take regular breaks in order to give your child the chance to

run about and play.

DANGER! For the safety of all vehicle occupants:

In the case of an emergency stop or accident, unsecured objects or people may cause injury to other occupants in the vehicle. Therefore, please always ensure that ...

•

the backrests of the vehicle seats are locked (e.g. If there is afolding rear seat

bench, check that it is latched in place).

•

all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are

secured.

•

all persons in the vehicle have their seat belts fastened.

•

the child seat is secured whenever it is in the vehicle, even if not carrying

achild.

WARNING! For your protection when handling the child seat:

•

Never use the child safety seat in afree-standing position, even for testing.

•

When swivelling the backrest up, 12 nothing must come between the back-

rest

and the seat cushion09. You or your child’s ﬁngers could be jammed

and injured.

•

To avoid damage, ensure that the child seat is not jammed in between hard objects (car door, seat rails, etc.).

•

Keep the child seat in asafe place when not in use. Do not place heavy objects on the seat and do not store it directly next to sources of heat or in direct sunlight.

CAUTION! To protect your vehicle:

•

Certain car seat covers made from more sensitive materials (e.g. velour, leather, etc.) may show signs of wear when achild seat is used on them. For optimum protection of your car seat covers, we recommend using the BRITAX RÖMER car seat protector from our range of accessories.

2. INTRODUCTION

We are delighted that you have chosen our child seat to accompany your child safely through anew stage in his or her life.

To protect your child correctly, the child seat must always be used and installed as described in these instructions!

If you have any further questions about the use of the child seat, please contact us:

Britax Childcare Britax Römer

Kindersicherheit GmbH Theodor-Heuss-Straße 9 89340 Leipheim Germany

Britax Childcare BritaxExcelsior Limited

1 Churchill Way West Andover Hampshire SP10 3UW United Kingdom

These instructions use the following symbols:

Symbol Keyword Explanation

WARNING! Risk of minor physical injury

CAUTION! Risk of material damage

Instructions that follow aﬁxed sequence are numbered. Example:

1. Press the button...

Belt guide colours

For clear dierentiation, the two vehicle seat belts are shown in dierent colours. The diagonal strap 16 is shown in dark red and the lap belt 15 in bright red. The belt guides on the child safety seat follow the same colour scheme.

T.: +49 (0) 8221 3670-199/-299 F.: +49 (0) 8221 3670 -210 E.: service.de@britax.com www.britax-roemer.com

T.: +44 (0) 1264 333343 F.: +44 (0) 1264 334146 E.: service.uk@britax.com www.britax-roemer.com

DANGER! Risk of serious physical injury

TIP! Useful notes

3. APPROVAL

BRITAX RÖMER

Child seat

KIDFIX² R KIDFIX² S

*ECE = European Standard for Child Safety Equipment

This child seat has been designed, tested and approved according to the requirements of the European Standard for Child Safety Equipment (ECE R 44/04). The certiﬁcation mark (letter E in acircle) and approval number can be found on the orange approval label (sticker on the child seat).

DANGER! The certiﬁcation is invalidated if any modiﬁcations are made to the

child seat. Only the manufacturer is permitted to make modiﬁcations to the child safety seat. The child seat is approved for use both with and without Secure-

Guard.

WARNING! The KIDFIX² R and KIDFIX² S must be used exclusively for securing your child in the vehicle. They are in no way suitable for use as aseat or atoy in the home.

DANGER! Never secure your child or the child seat with a2-point belt. If

your child is secured in the child seat with a2-point belt only, this may cause serious injuries, which could even be fatal.

Testing and certiﬁcation

In accordance with ECE* R 44/04

Group Body weight

II+III 15 to 36 kg

4. USE IN THE VEHICLE

Please refer to your vehicle’s instruction manual for instructions on how to use child restraint systems. The seat can be used in vehicles with ISOFIX anchoring systems (see type list) and in vehicles with 3-point belts.

Please refer to your vehicle’s instruction manual for information on the seats approved as child seats for weight class 15 to 36 kg.

The KIDFIX² R and KIDFIX² S are approved for two dierent installation methods:

Symbol Installation type Approval type

with the ISOFIT locking arms in the ISOFIX ﬁxing points on the vehicle. Check the list of vehicle types.

with the vehicle's 3-point seat belt universal

This means that the child seat may be used only in vehicles that are listed in the attached vehicle

type list. This type list is constantly being updated. The latest version can be obtained from us or at www.britax.com

You can install your child seat as follows:

in the direction of travel Yes against the direction of travel No with 2-point belt No with 3-point belt with ISOFIX ﬁxing points

(between seat surface and backrest)

On front passenger seat Yes On outer rear seat Yes on centre rear seat

(with 3-point belt)

Use is permitted on arear-facing vehicle seat (e.g. in avan or minibus) only if the vehicle seat is also

approved for use by adults. The seat must not be within the activated range of an airbag.

The safety belt must be approved to ECE R 16 or acomparable standard (indicated on the belt’s

test label by an "E" or "e" inside acircle).

If there is afront airbag: Slide the car seat well back and follow the related instructions in the vehi-

cle’s instruction manual.

Cannot be used if the vehicle seat is equipped with a2-point belt only.

Yes

semi-universal

15 – 36 kg

5. CARE AND MAINTENANCE

Please ensure that you only use original BRITAX RÖMER replacement seat covers, as the seat cover is an integral part of the child safety seat and fulﬁls important functions that ensure smooth operation of the system. Replacement seat covers are available from your dealer.

•

The cover can be removed and washed with amild detergent, selecting the

“Delicates” programme on the washing machine (30 °C). Please observe the

instructions on the washing label of the cover.

•

The plastic parts can be cleaned in soapy water. Do not use aggressive clean-

ing agents (such as solvents).

DANGER! The child safety seat must not be used without the seat cover.

Removing the seat cover

1. Push the headrest of the vehicle seat to its top position.

2. Unhook the cover hook

3. Pull o the top part of the cover and fold it forwards onto

the seat surface.

4. Release the cover hooks

and on both sides of the seat surface and loosen the plastic cards on the front of the seat cushion.

5. Pull the cover away from the seat surface. Removing the headrest cover

1. Unhook the cover straps

2. Unhook the cover hooks

3. Pull the headrest cover

hooks on the bottom of the headrest.

► The cover can now be washed. Please observe the

instructions on the washing label of the cover.

Putting the cover on

Follow the above steps in the reverse order to put the cover on.

on the rear of the backrest.

on the front of the backrest

on the rear of the backrest.

on the front of the backrest.

o; to do this, detach the two

6. ADJUSTING THE HEADREST

A correctly adjusted headrest 22 ensures optimal positioning of the diagonal

strap

, and gives your child optimum protection. The headrest 22 must be positioned so that two ﬁngers can be inserted between your child's shoulders the headrest

To adjust the height of the headrest to ﬁt your child:

1. Grasp the adjustment handle 10 on the back of the

headrest 22 and pull it upwards. This unlocks the headrest.

2. You can now move the unlocked headrest

to the desired height. When you release the adjustment handle 10, the headrest

3. Place the child seat on the car seat.

locks into place.

4. Sit your child on the child seat and check the height. Re-

peat the above procedure until the headrest correct height.

is at the

7. DISASSEMBLY AND DISPOSAL

UNFASTENING YOUR CHILD:

To unfasten your child, press the release button on the car seat buckle.

REMOVAL:

1. Press the release button on car vehicle seat buckle.

2. Open the dark red belt holder 03 by pressing the button on

the belt holder

backwards, then pull out the diagonal

belt 16.

Only for installation type A (ISOFIT):

3. To release the ISOFIT ﬁtting, squeeze the green locking

button 07 and red release button 06 together, ﬁrst on one side then on the other.

►The child safety seat can now be removed.

DANGER! The child seat must always be secured when in the vehicle, even if

not carrying achild.

RE-ATTACHING THE BACKREST:

4. Follow steps 1 - 7 in paragraph 9.1 “Removing the backrest“ in the reverse

order.

Please follow the disposal regulations applying in your country.

Disposal of packaging Container for cardboard boxes Seat cover Residual waste, thermal recycling Plastic parts To be placed in the corresponding container as

labelled Metal parts Container for metals Belt straps Container for polyester Buckle and clip Residual waste

8. Installation with backrest

8.1

The child seat is installed permanently in the vehicle with the ISOFIT locking arms05. Your child is then buckled into the child seat using the vehicle's 3-point seat

belt.

1. If your vehicle is not equipped with ISOFIX seat ﬁttings as standard, clamp the

TIP! The ISOFIX ﬁxing points are located between the seat surface and the

* The insertion aids make it easier to install the child seat with ISOFIX ﬁxing points and prevent damage

to the car seat covers. If they are not being used, remove them and keep them in asafe place. For vehicles with afolding backrest, the insertion aids need to be removed before folding the backrest. Any problems that occur are usually caused by dirt or external objects on the insertion aids and on the hook. Remove the dirt or external objects to resolve such problems.

With ISOFIT + BACKREST

two insertion aids the two ISOFIX ﬁxing points 01 in your vehicle.

backrest of the vehicle seat.

supplied with the seat*, with notch facing upwards, onto

2. Push the headrest of the vehicle seat to its top position.

3. Follow the steps in Section 6 “ADJUSTING THE HEADREST”.

4. Hold down the ISOFIT setting button

ISOFIT locking arms 05 fully out.

5. On either side of the seat, squeeze the green locking

button ensures that both hooks on the ISOFIT locking arms 05

and the red release button 06 together. This

are open and ready to use.

6. Place the child seat facing forward on acar seat ap-

proved for this purpose. Check that the backrest ﬂat against the backrest of the car seat.

02 05

7. Position the two ISOFIT locking arms

of the two insertion aids 02.

8. Push both ISOFIT locking arms

until the ISOFIT locking arms 05 engage on both

into the insertion aids

sides with an audible click.

DANGER! The green locking button

ble on both sides, indicating that the child seat is correctly fastened.

9. Hold down the ISOFIT setting button

child seat as far back as possible.

10. Shake the child seat to check that it is securely fastened,

and check the locking buttons

again to ensure that

they are both fully green.

11. Carry out the steps in paragraph 8.3 "SECURING THE

CHILD IN A CHILD SEAT WITH BACKREST".

and push the

directly in front

must be visi-

and push the

15 kg - 36 kg (~4 Y - 12 Y)

KIDFIX² R KIDFIX² S

User instructions

2000031236 18/09

www.britax-roemer.com

For the safety of your child, before every car journey check that...

► the child seat is engaged on both sides with the ISOFIT locking arms

in the

ISOFIT ﬁ xing points 01 and both locking buttons 07 are fully green;

► the lap belt

seat cushion;

► the lap belt

is passed into the bright red belt guides

is passed through the bright red SecureGuard 13;

► the diagonal strap

bright red belt guide

► the diagonal strap

on the vehicle belt buckle side 18 is also passed into the

on the seat cushion;

is passed through the dark red belt holder 03 at the

on both sides of the

headrest;

► the diagonal strap ► the straps are tight and not

runs diagonally backwards;

twisted;

► the vehicle belt buckle 18 is not placed in the bright red belt guide 04 on the

seat cushion.

DANGER! If your child tries to open the ISOFIT locking buttons 07 or the vehi-

cle belt buckle,

Guard

or to insert the diagonal strap 16 into the bright red Secure-

, stop your vehicle as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

8.2

With 3-POINT BELT + BACKREST

Follow the steps in Section 6 "ADJUSTING THE HEADREST".

1. Place the child seat on the car seat.

Check that the backrest

the car seat.

TIP! If the headrest of the car seat is preventing this, it

is ﬂ at against the backrest of

should be removed and stowed safely somewhere in the vehicle.

2. Carry out the steps in paragraph 8.3 "SECURING THE CHILD IN A CHILD SEAT WITH BACKREST".

For the safety of your child, before every car journey check that...

► the child seat is securely fastened, ► the lap belt

is passed into the bright red belt guides 04 on both sides of the

seat cushion,

► the lap belt ► the diagonal strap

bright red belt guide

► the diagonal strap

headrest,

► the diagonal strap ► the straps are tight and not

is passed through the bright red SecureGuard 13,

on the vehicle belt buckle side 18 is also passed into the

on the seat cushion,

is passed through the dark red belt holder

runs diagonally backwards,

twisted,

at the

► the vehicle belt buckle 18 is not placed in the bright red belt guide 04 on the

seat cushion.

DANGER! If your child tries to open the vehicle belt buckle 18 or insert the di-

agonal strap

into the bright red SecureGuard 13, stop your vehicle as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

8.3

SECURING THE CHILD IN A CHILD SEAT WITH BACKREST

KIDFIX² S

On the side nearer the vehicle door, turn the SICT 23 anti-clockwise until it is at adistance of 5 mm from the vehi-

cle door or until it is fully unscrewed.

All versions:

Pull out the vehicle belt and pass it in front of your child to the vehicle belt buckle 18.

DANGER! Check that the vehicle belt is not twisted,

otherwise the full protective e ect of the restraint system

is not ensured.

2. Engage the belt clip in the vehicle belt buckle

so that

there is an audible CLICK.

3. Insert the diagonal strap 16 and lap belt 15 on the vehi-

04 18

cle belt buckle side 18 into the bright red belt guide 04 on the seat cushion.

DANGER! The vehicle belt buckle 18 must not be

positioned between the bright red belt guide 04 and the armrest.

4. Also place the lap belt

in the bright red belt guide 04

on the other side of the seat cushion.

DANGER! The lap belt 15 must lie as low as possible

over your child's hips on both sides.

5. Insert the lap belt

in the bright red

SecureGuard 13.

DANGER! Do not pass the diagonal strap 16 into

the bright red SecureGuard 13.

into the dark red belt hol-

upwards. The diagonal

is fully closed.

is lying over your

der 03 at the headrest 22 until it is fully inside the belt holder 03without twisting.

TIP! If the backrest 12 is covering the belt holder 03,

youcan adjust the headrest

6. Pass the diagonal strap

strap

can then be easily inserted. Now move the

headrest the button on the belt holder

back to the correct height. Make sure that

7. Make sure that the diagonal strap

child's collarbone and not at his or her neck.

TIP! You can still also adjust the height of the headrest 22

in the vehicle.

DANGER! The diagonal strap

must run diagonally backwards. You can adjust the belt routing with the adjustable belt deﬂ ector in the vehicle.

DANGER! The diagonal strap 16 must never run for-

ward to the belt deﬂ ector on the vehicle. In this case, use the child seat on the rear seat only.

8. Tighten the vehicle belt by pulling on the diagonal

strap

9. Follow the steps listed in Section 8 “ your child, before every car journey check that ...

For the safety of

”

9. USING AS A BOOSTER SEAT

9.1

For age group 3 (22 kg to 36 kg), the child seat can also be used as abooster seat

without the backrest. Follow the steps described below for the removal and attachment of the backrest. You will need aTX20 Torx screwdriver. BRITAX RÖMER recommends using it with the backrest as this provides your child with optimum protection in the case of aside impact. If using without the backrest, suﬃ cient side impact protection can be ensured only with side curtain airbags at the seat positions. For information about vehicle equipment options, please contact the manufacturer of your vehicle.

group3 (22 to 36 kg) and is taller than 125 cm. For all other age groups, the product must be used with the backrest . We recommend using the seat with the backrest for as long as possible, and as abooster seat starting from achild height of 135 cm.

REMOVING THE BACKREST

DANGER! Use this product as abooster seat only if your child is in age

1. Place the seat on alevel surface.

2. Open the ﬂ ap on the storage compartment

bottom of the booster seat and take out the screwdriver.

on the

Torx

3. Lift the cover of the backrest 12 and fold it forward.

4. Lift the cover of the seat cushion

5. Loosen the 4 Torx screws on the backrest

6. Push the seat cushion

the connection snaps out.

towards the backrest 12 until

and fold it backward.

7. So as not to lose them, screw the 4 screws back into the

holes provided in the backrest

8. Pull the seat cushion cover

back and hook the trans-

parent plastic piece onto the notch provided.

9.2

For design reasons in some vehicle models, the diagonal strap

USING THE FLEXIBLE BELT GUIDE

may not pass ideally over your child's shoulder area. When using as abooster seat, always check that the diagonal strap 16 is located in the area indicated. If the diagonal

strap

does not pass through the correct (green) area, the ﬂ exible belt guide 24

must also be used.

16 16

Attaching the ﬂ exible belt guide - securing with ISOFIT locking arms

1. Open the ﬂ ap on the storage compartment 25 on the

bottom of the seat cushion belt guide 24.

2. Close the ﬂ ap on the storage compartment

3. Pass the metal attachment

arm 27 located on the vehicle belt buckle side.

4. Place the belt guide clip

on the sitting surface of the seat cushion

5. Follow the remaining steps for the installation method

and take out the ﬂ exible

over the ISOFIX locking

of the ﬂ exible belt guide 24

FASTENING WITH ISOFIT LOCKING ARMS AS A SEAT CUSHION WITHOUT BACKREST

6. Attach the belt guide clip

to the diagonal strap 16. Check that the belt of the ﬂ exible belt guide 24 is not twisted and passes diagonally behind your child.

7. Adjust the belt guide clip

so that the diagonal strap 16 is located in the green area.

DANGER! The diagonal strap 16 must always be in

the area indicated.

16 16

Attaching the ﬂ exible belt guide - securing with the vehicle 3-point belt

1. Open the ﬂ ap on the storage compartment

on the bottom of the booster seat and take out the ﬂ exible belt guide 24.

2. Close the ﬂ ap on the storage compartment

9.3

3. Engage the metal attachment 26 in the ISOFIX locking

arm 27 located on the vehicle belt buckle side.

4. Place the belt guide clip

on the sitting surface of the booster seat.

5. Follow the remaining steps for the installation method

of the ﬂ exible belt guide 24

9.4 FASTENING WITH 3-POINT BELT AS A SEAT CUSHION WITHOUT BACKREST

6. Attach the belt guide clip

to the diagonal strap. Check

that the belt of the ﬂ exible belt guide 24 is not twisted.

7. Adjust the belt in the belt guide clip

so that the diagonal strap 16 is located in the green area. If the diagonal belt is not in the green area even with the ﬂ exible belt

guide backrest on this seat.

, the child seat must not be used without the

DANGER! The diagonal belt must always be located

in the area indicated.

9.3

FASTENING WITH ISOFIT LOCKING ARMS AS ABOOSTER SEAT WITHOUT BACKREST

The child seat is installed permanently in the vehicle with the ISOFIT locking arms. Your child is then buckled into the child seat with the vehicle's 3-point seat belt.

1. If your vehicle is not equipped with ISOFIX seat ﬁ ttings as standard, clamp

the two insertion aids 02 supplied with the seat*, with notch facing upwards, onto the two ISOFIX ﬁ xing points 01 in your vehicle.

TIP! The ISOFIX ﬁ xing points are located between the seat surface and the

backrest of the car seat.

* The insertion aids make it easier to install the child seat with the ISOFIX ﬁ xing points and they

prevent damage to the car seat covers. If they are not being used, remove them and keep them in asafe place. For vehicles with afolding backrest, the insertion aids need to be removed before folding the backrest. Any problems that occur are usually caused by dirt or external objects on the insertion aids and on the hook. Remove the dirt or external objects to resolve such problems.

2. Hold down the ISOFIT setting button 08 and push the

ISOFIT locking arms 05 fully out.

3. On both sides of the seat, squeeze the green locking but-

070605

and the red release button 06 together. This en-

ton sures that both hooks on the ISOFIT locking arms 05 are open and ready to use.

4. Place the child seat facing forward on acar seat ap-

proved for this purpose.

5. Position the two ISOFIT locking arms

0502

of the two insertion aids 02.

6. Push both ISOFIT locking arms

until the ISOFIT locking arms 05 engage on both

sides with an audible click.

DANGER! The green locking button

directly in front

into the insertion aids

must be visible on both sides, indicating that the child seat is correctly fastened.

7. Hold down the ISOFIT setting button

and push the

child seat as far back as possible.

8. Shake the child seat to check that it is securely fastened,

and check the locking buttons

again to ensure that

they are both fully green.

9. Carry out the steps in paragraph 9.5 "SECURING THE

CHILD IN A CHILD SEAT WITHOUT BACKREST".

For the safety of your child, before every car journey check that...

► the child seat is engaged on both sides with the ISOFIT locking arms 05 in the

ISOFIT ﬁ xing points 01 and both locking buttons07 are fully green,

► the lap belt

seat cushion,

► the lap belt ► the diagonal strap

bright red belt guide

► the diagonal strap

is passed into the bright red belt guides

is passed through the bright red SecureGuard 13,

on the vehicle belt buckle side 18 is also passed into the

on the seat cushion,

runs diagonally backwards,

► the straps are tight and not

twisted,

on both sides of the

► the vehicle belt buckle 18 is not placed in the bright red belt guide 04 on the

seat cushion.

DANGER! If your child tries to open the ISOFIT locking buttons 07 or the vehi-

cle belt buckle

Guard

or to insert the diagonal strap 16 into the bright red Secure-

, stop your vehicle as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

9.4

FASTENING WITH 3-POINT BELT AS A SEAT CUSHION WITHOUT BACKREST

The child seat is not installed permanently in the vehicle. It is simply secured along with your child by the vehicle's 3-point seat belt.

1. Place the child seat on asuitable vehicle seat.

Follow the steps in paragraph 9.5 “SECURING THE CHILD IN A CHILD SEAT WITHOUT

BACKREST”.

For the safety of your child, before every car journey check that...

► the child seat is securely fastened, ► the lap belt

is passed into the bright red belt guides 14 on both sides of

the seat cushion,

► the lap belt ► the diagonal strap

the bright red belt guide

► the diagonal strap ► the straps are tight and not

is passed through the bright red SecureGuard 13,

on the vehicle belt buckle side 18 is also passed into

on the seat cushion,

runs diagonally backwards,

twisted,

► the vehicle belt buckle 18 is not placed in the bright red belt guide 04 on the

seat cushion.

DANGER! If your child tries to open the vehicle belt buckle 18 or insert the di-

agonal strap

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 7 “REMOVAL AND DISPOSAL”.

9.5

SECURING THE CHILD IN A CHILD SEAT WITHOUT BACKREST

1. Sit your child sit in the child seat.

2. Pull out the vehicle belt and pass it in front of your child to

the vehicle belt buckle

DANGER! Check that the vehicle belt is not twisted,

otherwise the full protective e ect of the restraint system is not ensured.

3. Engage the belt clip in the vehicle belt buckle

so that

there is an audible CLICK.

and lap belt 15 on the vehi-

vehicle

belt buckle 18 should not be

in the bright red

4. Insert the diagonal strap

cle belt buckle side 18 into the bright red belt guide 04

on the seat cushion.

DANGER! The

in the same area as the bright red belt guide 04. The lap belt

child's hips on both sides.

5. Insert the lap belt

must lie as low as possible over your

SecureGuard 13.

DANGER! Do not insert the diagonal strap 16 into

the bright red SecureGuard 13.