Britax KIDFIX II XP, KIDFIX II XP SICT User Instructions

01 02

05 06

Belt guide (bright red)

Release knob

XP-SICT (only KIDFIX II XP SICT)

Belt holder (dark red)

ISOFIX insertion aids

ISOFIX fastening points (automobile)

ISOFIT locking arms

01 02 03 04

05 06 07

Backrest

SecureGuard

ISOFIT adjustment button

Safety button

Storage compartment

09 10

XP-PAD

Adjusting handle of the headrest

13 14

Removing the seat cover

Moving the headrest of the vehicle seat into the top

position.

2. Unhook the cover hook

on the rear of the backrest.

Remove the top part of the cover and fold it forwards to

the seat surface.

4. Unhook the cover hook

on the front of the backrest.

5. Pull the cover o of the seat surface.

Removing the headrest cover

Unhook the cover loop

on the rear of the backrest.

7. Unhook the cover hook

on the front of the backrest.

Pull o the cover of the headrest

ŹThe cover can now be washed.

Please observe the

instructions on the washing label of the cover:

Re-ﬁtting the cover

Proceed in reverse order to put on the cover.

5. CARE AND MAINTENANCE

Seat cushion

2. INTRODUCTION

Thank you for choosing

KIDFIX II XP / KIDFIX II XP SICT

to keep your child

safe through a new stage of their life.

In order to protect your child correctly, the

KIDFIX II XP / KIDFIX II XP

SICT

must always be used and installed as described in these instructions.

If you have any further questions regarding its use, please feel free to contact us:

These instructions use the following symbols stated below:

Symbol Keyword Explanation

DANGER! Risk of severe personal injury

WARNING! Risk of minor personal injury

CAUTION! Risk of material damage

TIP: Useful notes

Instructions that follow a set sequence are numbered. Example:

1. Press the button...

Belt guide colours

For better dierentiation, the two vehicle seat belts are highlighted in dierent colours. The diagonal seat belt

in dark red and the lap belt

in bright red. The colour of the belt guides on the child safety seat follows the same colour scheme.

4. USE IN THE VEHICLE

Please observe the instructions for using children's restraining systems in the operating instructions of your vehicle. The seat can be used in vehicles with ISOFIX anchoring systems (see type list) and in vehicles with a

3-point belt.

Please ﬁnd the information on the seats approved for child safety seats of the weight classes 15 to 36 kg in the operating instructions of your vehicle

The KIDFIX II XP / KIDFIX II XP SICT is approved for two dierent methods of installation:

Symbol Installation type Approval type Section

with the ISOFIT locking arms on the ISOFIX fastening points in the vehicle. Observe the vehicle type list.

semiuniversal

with the vehicle's 3-point seatbelt

universal

This means that the child safety seat may only be used in vehicles that are listed in the vehicle type list enclosed. This type list is consistently kept up to date. The latest version can be obtained from us or from www.britax.com

You can use your child safety seat as follows:

In the direction of travel Yes

Against the direction of travel No

with 2-point belt No

with 3-point belt

Yes

with ISOFIX fastening points

(between seat surface and

backrest)

Yes

on front passenger seat Yes

on outer rear seat Yes

on centre rear seat (with

3-point belt)

Yes

1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only if the vehicle seat is also approved for use by adults. The seat may not be in the area of eect of an airbag.

2) The safety belt must be approved to ECE R 16 or a comparable standard (see test label on belt with an "E" or "e" in a circle).

3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions in vehicle owner's manual.

4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.

15-36 kg

3. CERTIFCATION

BRITAX RÖMER

Vehicle child safety

seat

Testing and certiﬁcation

In accordance with ECE* R 44/04

Group Body weight

KIDFIX II XP

KIDFIX II XP SICT

II+III 15 to 36 kg

*ECE = European Standard for Child Safety Equipment

The child safety seat has been designed, tested and certiﬁed according to the requirements of the European Standard for Child Safety Equipment (ECE R 44/04). The seal of approval E (in a circle) and the approval number are located on the orange approval label (sticker on the child safety seat).

DANGER! This approval will be invalidated if you make any modiﬁcations to

the child safety seat. Only the manufacturer is permitted to make modiﬁcations to the child safety seat.

WARNING! Use the

KIDFIX II XP / KIDFIX II XP SICT

exclusively for securing your child in your vehicle. It is in no way suitable as a seat or toy in the home.

DANGER! Never secure your child or the child safety seat with a 2-point

belt. If you secure your child in the child seat with only a 2-point belt, then in the event of an accident this may cause serious injuries to your child, possibly resulting in death.

PAGE I

6. DISASSEMBLY AND DISPOSAL

Please ensure that you only use the original BRITAX RÖMER replacement seat covers, as the seat cover is an integral part of the child safety seat and fulﬁls important functions to ensure the smooth operation of the system. Replacement seat covers are available from your dealer.

• The cover can be removed and washed with a mild detergent in the delicates programme of the washing machine (30 °C). Please observe the instructions on the washing label of the cover.

• The plastic parts and the XP-PAD can be cleaned with a soap sud. Do not use any caustic cleaning agents (such as solvents).

DANGER! The child seat must not be used without the seat cover.

1. PRODUCT OVERVIEW

1. Operate the release key of your vehicle seat buckle

2. Open the XP-PAD

on the Velcro fastener and

remove the diagonal belt

3. Open the dark red belt holder

by pressing

backwards the key on the belt holder

and

unthreading the diagonal belt

Only for installation type A (ISOFIT):

4. To release the ISOFIT fastening, release the green

safety button

and the red release button 07 ﬁrst on the one and the on the other side opposite on another.

ŹThe child safety seat can now be removed.

DANGER! The child safety seat must always be

secured when it is in the vehicle, even if no child is being transported.

DISPOSAL:

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes Seat cover Residual waste, thermal utilisation Plastic parts According to the labelling in the

corresponding container Metal parts Container for metals Belt straps Container for polyester buckle and tongue Residual waste

0807

REMOVAL:

UNFASTENING YOUR CHILD:

1. To unfasten your child, use the release button of your vehicle seat buckle.

TIP! The XP-PAD can remained applied for easier use on the diagonal belt

of your vehicle, the diagonal belt must be retensioned before every journey; see: Section10 step 12 [page II].

KIDFIX II XP KIDFIX II XP SICT

User instructions

www.britax.com

2000022092 - 06/15

15 kg - 36 kg (~4 Y - 12 Y)

Britax Childcare

Britax Römer Kindersicherheit GmbH Blaubeurer Strasse 71 D-89077 Ulm Germany

T.: +49 (0) 731 9345-199/-299 F.: +49 (0) 731 9345-210 E.: service.de@britax.com www.britax.com

Britax Childcare

Britax Exelsior Limited 1 Churchill Way West Andover Hampshire SP10 3UW

T.: +44 (0) 1264 333343

F.: +44 (0) 1264 334146 E.:

service.uk@britax.com

www.britax.com

6. Place the XP-PAD 11 in the side of the child safety

seat closer to the vehicle door.

8. Place the child safety seat in driving direction on

a vehicle seat approved for use.Ensure that the backrest

is ﬂush with the backrest of the vehicle

seat .

9. Position the two ISOFIT locking arms

directly in

front of the two insertion aids

10. Push both ISOFIT locking arms

into the insert

guides

until the ISOFIT locking arms 06 engage

on both sides with a clicking sound.

DANGER! The green safety button 08 must be

visible on both sides so that the child safety seat is correctly fastened.

11. Hold the ISOFIT

settings button

down and push

the child safety seat as far back as possible.

1. Carry out the steps in Section 8 "ADJUSTING THE HEADREST".

2. Place the XP-PAD

on the side of the child safety

seat closer to the vehicle door.

3. Guide the elastic holding strap of the XP-PAD

into the dark red belt holder

of the headrest 22

until it lies completely in the belt holder

and is

not twisted.

4. Place the child seat on the vehicle seat. Ensure that the backrest

is ﬂush with the backrest of the

vehicle seat.

Tip! If the headrest of the vehicle seat gets in the way, turn it the other way.

5. Carry out the steps in Section 10 "SECURING YOUR CHILD".

12. Shake the child safety seat to ensure that it is

securely fastened and check again the fastening buttons

to ensure that both are fully green.

13. Carry out the steps in Section 10 "SECURING YOUR CHILD".

For the safety of your child, before every journey in the car check that...

Źthe child safety seat is slotted in on both sides with the ISOFIT locking arms

in the ISOFIT fastening points 01 and both safety buttons 08 are fully green;

Źthe child safety seat is securely fastened; Źthe lap belt 16 runs in the bright red belt guides on both sides of the seat

cushion 05,

Źthe

lap belt 16 runs through the bright red

SecureGuard 10.

Źthe diagonal seat belt section 17 on the side of the vehicle seatbelt buckle

also runs through the light red belt guide 05 of the seat cushion,

Źthe diagonal seat belt section 17 runs through the dark red belt holder 03 of

the headrest,

ŹXP-PAD

and XP-SICT 04 are correctly installed and used,

Źthe diagonal seat belt section 17 runs diagonally backward, Źthe straps are tight and not twisted, Źthe seatbelt buckle 18 must not be positioned on the red belt guide 05 in

the seat cushion.

DANGER!

If your child try to use to open the vehicle belt buckle 18 or

introduce the diagonal belt section

into the bright red SecureGuard 10, stop as soon as possible. Check whether the child safety seat is correctly fastened and ensure that your child is correctly secured. Explain to your child the dangers associated with his actions.

7. SAFETY NOTES

Please take the time to read these instructions carefully and keep them

to hand in the intended storage compartment

on the child safety seat at all times! The instructions must be with the child safety seat if the latter is passed on to a third party.

DANGER! For the protection of your child:

• In the event of an accident with a collision speed of more than 10 km/h, the

child safety seat may be damaged without the damage becoming immediately visible. In this case the child safety seat must be replaced. Please dispose of it properly.

• As a rule, have your child safety seat checked if it was damaged (e.g if it falls

on the ground).

• Regularly check all important parts for damage. Ensure that all mechanical

parts, in particular, are fully functional.

• Never lubricate or oil parts of the child seat.

•

Never leave your child unattended in the child seat in the vehicle.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Protect the child safety seat from intensive direct sunlight when it is not in use.

The child safety seat can get very hot in direct sunshine. Child skin is sensitive and could thereby be harmed.

•

The more snugly the belt ﬁts over your child's body, the better they will be protected. Therefore avoid putting thick clothes on your child under the belt.

• Take regular breaks on long journeys in order to give your child the

opportunity to play around.

• Use on the rear seat: Move the front seat forward far enough that you child's

feet cannot hit the backrest of the front seat (to prevent risk of injury).

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or an accident, unsecured persons or objects may cause injury to other vehicle occupants. Please always check that...

• the backrests of the vehicle seats are locked (i.e. that any foldable rear seat

bench latch is engaged).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are

secured.

• all persons in the vehicle have their seatbelts fastened.

• the child safety seat is always secured when it is in the vehicle, even if no child

is being transported.

WARNING! For your protection when handling the child seat:

• Never use the child safety seat free-standing, not even for test sitting.

• The backrest

may tip backward. Always place the child seat on the vehicle

seat before having your child sit down in it.

• When swivelling up the backrest

, nothing must come between the

backrest

and the seat cushion15 . You or your child could pinch your

ﬁngers, injuring them.

•

To avoid damage, ensure that the child safety seat is not jammed in between hard objects (car door, seat rails, etc.).

•

Keep the child safety seat in a safe place when it is not in use. Do not place any heavy objects on the seat and do not store it directly next to sources of heat or in direct sunlight.

CAUTION! To protect your vehicle:

•

Certain car seat covers made from more sensitive materials (e.g. velour, leather, etc.) may sustain signs of wear and tear when using child safety seats. For optimum protection of your car seat covers, we recommend using the BRITAX RÖMER car seat protector from our range of accessories.

PAGE II

For the safety of your child, before every journey in the car check that...

Źthe child safety seat is securely fastened; Źthe lap belt 16 runs in the bright red belt guides on both sides of the seat

cushion

Źthe

lap belt 16 runs through the bright red

SecureGuard 10.

Źthe diagonal seat belt section 17 on the side of the vehicle seatbelt buckle

also runs through the light red belt guide 05 of the seat cushion,

Źthe diagonal seat belt section 17 runs through the dark red belt holder 03

of the headrest,

Źthe diagonal seat belt section 17 runs diagonally backward, Źthe straps are tight and not twisted, ŹXP-PAD 11 and XP-SICT 04 are correctly installed and used, Źthe seatbelt buckle18 must not be positioned on the red belt guide 05 in

the seat cushion.

DANGER! If your child try to use to open the vehicle belt buckle 18 or

introduce the diagonal belt section

A correctly set headrest

ensures that the diagonal seat belt section 17 is optimally positioned, and gives your child optimum protection. The headrest

must be adjusted so that there is a space two ﬁngers wide

between the headrest

and your child's shoulders.

To adjust the height of the headrest to ﬁt your child:

1. Reach into the adjustment handle

on the back

of the headrest

and pull it towards you.

This unlocks the headrest.

2. You can now move the unlocked headrest

to the desired height. As soon as you release the adjustment handle

, the headrest 22 will lock

into place.

3. Place the child safety seat on the vehicle seat.

4. Have your child sit down in the child safety seat and

check the height. Repeat the procedure until the headrest

has the correct height.

1. If your vehicle is not ﬁtted with ISOFIX insertion aids by standard, clamp

the two insertion aids

, with are included in the scope of delivery of the

seat*, with the section pointing upwards to the two ISOFIX fastening points

of your vehicle.

TIP!

The ISOFIX fastening points are located between the surface and the backrest

of the vehicle seat.

* The insertion aids facilitate the installation of the child safety seat with the use of the SOFIX fastening points and prevent damage to the car seat covers. As long as they are not used, remove them and keep them in a safe place. For vehicles with foldable a backrest, the insertion aids need to be removed before folding the backrest. Any problems occurring usually come from soiling or external objects on the insertion aids and on the hook. Remove soiling or external objects to rectify such problems.

2. Moving the headrest of the vehicle seat into the top position.

3. Carry out the steps in Section 8 "ADJUSTING THE HEADREST".

8. ADJUSTING THE HEADREST

9. INSTALLATION

With ISOFIT + 3-point belt

The

KIDFIX II XP / KIDFIX II XP SICT

is installed permanently in the vehicle with

the ISOFIT locking arms. Your child is then buckled into the child seat with the vehicle's 3-point seatbelt.

4. Hold the ISOFIT

settings button

down and push

the ISOFIT locking arms

out in full .

KIDFIX II XP SICT & KIDFIX II XP:

1. Let your child sit in the child safety seat and place

the XP-PAD

over the chest area of your child

2. Pull out the vehicle belt and guide it in front of your

child to the vehicle seat buckle

DANGER! Ensure the vehicle belt is not twisted, as

otherwise the full protective eect of the retaining system is not ensured.

3. Engage the buckle tongue in the vehicle seat buckle

with a CLICK!

4. Place the diagonal seat belt section

and lap

belt section

on the side of the vehicle seatbelt

buckle

into the light red belt guide 05of the seat

cushion.

DANGER! The vehicle seatbelt buckle must not

be positioned between the light red belt guide and the armrest.

18 05

5. Also place the lap belt section 16 on the other side

of the seat cushion in the light red belt guide

DANGER! The lap belt section 16 must lie as low

as possible over your child's hips on both sides.

7. Guide the diagonal seat belt section

into the dark

red belt holder

of the headrest 22 until it lies

completely in the belt holder

and is not twisted.

Tip! If the backrest 14 conceals the belt holder 03, you can adjust the headrest

upwards. The diagonal

seat belt section

can now be easily inserted. Now

return the headrest

to the proper height.

8. Ensure that the diagonal belt 17 runs over the collar-

bone of your child and is not on the neck and that the key on the belt holder is

fully closed.

Tip! You can still adjust the height of the headrest 22

again here in the vehicle.

9. Open the Velcro fastener on the XP-PAD

and fold

the top part of the XP-PAD

to the side.

10. Insert the diagonal belt

in the die nubby surface

of the XP-PAD

11. Close the XP-PAD

again by folding the folded

part back and closing the Velcro fastener.

DANGER! The diagonal seat belt section 17 must

run diagonally backward. You can adjust the course of the belt with your vehicle's adjustable belt deﬂector.

DANGER! The diagonal belt 17 must never be

directed forwards to the belt deﬂector on the vehicle. In this case, use the child safety seat on the back seat only.

12. Tighten the vehicle seat belt by pulling on the diagonal

seat belt section

13. Observe the further steps of the relevant installation

type.

KIDFIX II XP SICT:

Unscrew the XP-SICT

anti-clockwise (on the side closer to the vehicle door) until it has a distance of 5 mm to the vehicle door or has been unscrewed to the maximum.

5. Push the green safety button 08 and the red release

button

on both sides of the seat towards each other. This ensures that both hooks on the ISOFIT locking arms

are open and ready to use.

10. SECURING YOUR CHILD

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child safety seat, observe the steps in Section 6 "

REMOVAL AND DISPOSAL" [PAGE I]

2212

0807

The

KIDFIX II XP / KIDFIX II XP SICT

is not installed permanently in the vehicle. It

is simply secured together with your child using the vehicle's 3-point seatbelt.

With 3-point belt

7. Guide the elastic holding strap of the XP-PAD 11

into the dark red belt holder

of the headrest 22

until it lies completely in the belt holder

and is not

twisted.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child safety seat, observe the steps in Section 6

"REMOVAL AND DISPOSAL" [PAGE I]

170322

Adjusting the backrest: The backrest

is connected to the seat cushion 15 by

an articulated axis. The backrest

of the child seat can be adjusted to any inclination of the vehicle seat. Please know that optimal protection is guaranteed only if the vehicle seat is in an upright position.

0602

6. Guide the lap belt section 16 into the bright red

SecureGuard

DANGER!

Do not guide the diagonal the section 17 into the bright red SecureGuard

10 16

Britax KIDFIX II XP, KIDFIX II XP SICT User Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual