Page 1
Series No. S3401
Flexx
™
Travel System Stroller
Instruction Manual
Note: Second Seat, Bassinet, Britax Safe N Sound Unity Neos Baby Capsule or
Britax Safe N Sound Unity Baby Capsule ISOFIX compatible are all sold separately.
IMPORTANT: KEEP THIS BOOKLET IN A SAFE PLACE FOR FUTURE REFERENCE.
Page 2
02
CONTENTS
STROLLER SECTION
Stroller Warnings & Important Notes.....................................................................
Manual Handling Techniques................................................................................
Stroller Parts List...................................................................................................
Single Stroller Configurations.................................................................................
Tandem Configurations..........................................................................................
STROLLER ASSEMBLY
Opening the stroller frame......................................................................................
Installing & removing the single stroller axle..........................................................
Installing the front wheels.......................................................................................
Removing the front wheels.....................................................................................
Installing the rear wheels.......................................................................................
Removing the rear wheels......................................................................................
Attaching the storage basket..................................................................................
Attaching the stroller seat......................................................................................
Removing the stroller seat.....................................................................................
Attaching the canopy.............................................................................................
Removing the canopy............................................................................................
Attaching the arm bar.............................................................................................
Removing the arm bar...........................................................................................
Attaching the shoulder harness pads....................................................................
Attaching the boot cover........................................................................................
Attaching the rain cover.........................................................................................
STROLLER OPERATION
Using the brakes....................................................................................................
Using the front wheel swivel lock...........................................................................
Adjusting the handle height...................................................................................
Adjusting the leg rest.............................................................................................
Adjusting the backrest...........................................................................................
Securing your child in the harness.........................................................................
Adjusting the harness............................................................................................
Opening the harness.............................................................................................
Adjusting the shoulder harness height..................................................................
Using the tether strap............................................................................................
05
07
08
11
12
13
14
15
15
16
16
17
18
19
20
22
22
23
24
24
25
25
27
27
28
29
30
31
32
32
33
Page 3
03
CONTENTS
STROLLER OPERATION
Using the stroller....................................................................................................
Folding the stroller.................................................................................................
Lifting and carrying the stroller...............................................................................
TANDEM PACK SECTION
Second Seat Warnings & Important Notes............................................................
Tandem Pack Parts List.........................................................................................
TANDEM PACK ASSEMBLY
Installing and removing the tandem axle...............................................................
Attaching the storage basket.................................................................................
Attaching the second seat to the tandem axle.......................................................
Removing the second seat from the tandem axle.................................................
Installing and removing the height adaptors..........................................................
BASSINET SECTION
Bassinet Warnings & Important Notes...................................................................
Bassinet Parts List.................................................................................................
BASSINET ASSEMBLY
Assembling the bassinet........................................................................................
BASSINET OPERATION
Attaching the bassinet to the stroller frame...........................................................
Attaching the boot cover........................................................................................
Removing the bassinet from the stroller frame......................................................
Adjusting the canopy.............................................................................................
Attaching the bassinet to the tandem axle.............................................................
Removing the bassinet from the tandem axle........................................................
BABY CAPSULE SECTION
Baby capsule Warnings & Important Notes...........................................................
BABY CAPSULE OPERATION
Installing and removing the Baby capsule adaptors..............................................
Attaching the Unity Click & Go Baby capsule to the stroller frame........................
34
35
37
39
40
41
42
43
44
45
49
51
51
52
53
53
47
48
48
55
57
58
Page 4
04
CONTENTS
BABY CAPSULE OPERATION
Removing the Unity Click & Go Baby capsule from the stroller frame...................
CARE AND MAINTENANCE ................................................................................
NOTES ..................................................................................................................
59
60
61
Page 5
05
WARNINGS
ALWAYS FOLLOW THE MANUFACTURERS INSTRUCTIONS.
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE OF
THIS STROLLER.
THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL.
WARNINGS: TO AVOID INJURY OR DEATH:
• DO NOT LEAVE CHILDREN UNATTENDED.
• SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU
ADJUST THE STROLLER.
• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR
USE WITH THIS STROLLER BY BRITAX.
• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH
THIS STROLLER.
• THE MAXIMUM WEIGHT OF THE CHILD USING THIS STROLLER IS NOT
TO EXCEED 20 KG, 9KG FOR THE BASSINET, 12KG FOR THE SAFE-N SOUND UNITY NEOS OR SAFE-N-SOUND UNITY BABY CAPSULE ISOFIX
COMPATIBLE CLICK & GO BABY CAPSULE OR 17KG FOR THE SECOND
SEAT.
This CAUTION Symbol is shown at certain steps in this
Instruction Manual to highlight the danger of being injured by
moving parts.
CAUTION
FOR IMPORTANT NOTES AND WARNINGS ON ACCESSORIES - REFER TO
THEIR INDIVIDUAL SECTIONS IN THIS BOOK. THE MAXIMUM WEIGHT
VARIES FOR EACH ACCESSORY.
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS
STATIONARY.
Page 6
06
IMPORTANT NOTES
• USE GREAT CARE WHEN USING THE STROLLER ON STAIRS,
ESCALATORS, TRAVELATORS OR OTHER MOVING SURFACES.
• IT IS RECOMMENDED TO REMOVE THE CHILD FROM THE STROLLER
BEFORE GOING UP OR DOWN STAIRS OR ESCALATORS.
• DO NOT LIFT THE STROLLER BY THE ARM BAR (Supplied) BECAUSE IT
MAY DISENGAGE.
• DO NOT ALLOW CHILDREN TO STAND ON THE SEAT.
• DO NOT HANG BAGS OR GOODS FROM THE HANDLE AS THIS COULD
CAUSE THE STROLLER TO TIP OVER.
• DO NOT LEAVE THE STROLLER AND ITS ACCESSORIES NEAR AN OPEN
FIRE OR EXPOSED FLAME.
• DO NOT PLACE MORE THAN 4 KG IN THE BASKET, OR 1KG IN THE
CANOPY POCKET (IF SUPPLIED).
Page 7
07
MANUAL HANDLING TECHNIQUES
The SMART lifting technique
This technique can be used to pick up small light loads from low levels.
Size up the Load
• Assess the load (size, shape and weight).
• Assess whether the load needs to be moved;
• Where is it going to be placed” Check that there are no obstructions;
• Assess whether mechanical or human assistance is required.
Move the Load as close to the body as possible
• A load is heavier to lift or carry if it is not close to the body.
• The whole hand should be used to ensure a firm grip.
Always bend your knees
• Maintain balance.
• Keep feet apart and in a comfortable position.
• Minimise lower back bending.
• Bend knees preferable at as large an angle as possible but not at a right angle use a semi squat in preference to a full squat.
Raise the load with your legs
• Achieve the lift smoothly and without jerkiness.
• Maintain the normal curvature of the spine to allow the force of the load to be
distributed evenly from the spine to the pelvis.
Turn your feet in the direction that you want to move the load.
• Avoid unnecessary bending, twisting and reaching.
• Change direction by turning your feet and not your back.
• To set the load down, squat down, keep your head up and let
• Let your legs do the work.
Remember to ‘THINK TALL’ chest lifted, shoulders relaxed, chin tucked in
and head level.
Page 8
08
PARTS LIST
1 x Stroller frame
1 x Stroller axle
1 x Canopy
2 x Front wheels
2 x Rear wheels
1 x Stroller seat
Page 9
09
PARTS LIST
1 x Arm bar
1 x Extendable Storage basket
1 x Set of shoulder harness pads
1 x Boot cover
1 x Rain Cover
Page 10
1010
SINGLE STROLLER CONFIGURATIONS
Stroller seat forward-facing
Bassinet rearward-facing
Baby Capsule rearward-facing
Stroller seat rearward-facing
Page 11
11
TANDEM CONFIGURATIONS
WARNING:
DO NOT USE THE FLEXX STROLLER OR FLEXX
ACCESSORIES IN ANY TANDEM CONFIGURATION NOT SPECIFIED IN
THIS INSTRUCTION MANUAL.
The stroller seat and second seat can be used in all 4
recline positions.
The leg rest on the stroller seat will need to be
adjusted to allow for the recline position of the
second seat.
IMPORTANT NOTE:
HEIGHT ADAPTORS ARE SUPPLIED WITH THE TANDEM PACK.
THE HEIGHT ADAPTORS ARE USED TO CREATE MORE SPACE BETWEEN
THE UPPER & LOWER POSITIONS (IF REQUIRED) OF THE STROLLER.
DO NOT USE THE HEIGHT ADAPTORS IN SINGLE STROLLER MODE.
PLEASE NOTE: Shown with optional Accessories (sold separately).
The stroller seat can be used in all 4 recline positions.
The canopy on the bassinet will need to be adjusted to
accommodate the lower recline positions of the
stroller seat.
The stroller seat and second seat can be used in all 4
recline positions.
Page 12
12
TANDEM CONFIGURATIONS
The stroller seat can be used in all 4 recline positions.
The leg rest on the stroller seat will need to be
adjusted to accomodate the bassinet.
The canopy on the bassinet will need to be adjusted to
allow for the recline positions of the stroller seat.
Please Note: The bassinet in the lower position cannot
have the canopy fully extended.
The second seat can be used in all 4 recline positions.
Page 13
13
STROLLER ASSEMBLY
1
2
IMPORTANT NOTES:
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
• RELEASE THE STORAGE LATCH WITH DUE CARE AND OPEN THE
FRAME.
• WHEN OPENING THE STROLLER, BE AWARE OF THE DANGER OF
BEING INJURED BY MOVING PARTS AND LOCKING DEVICES DURING
THE PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS.
• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE
INJURED WHEN THE STROLLER IS BEING UNFOLDED, DUE CARE
SHOULD BE EXERCISED.
• KEEP CHILDREN CLEAR OF THE STROLLER WHEN UNFOLDING THE
STROLLER FRAME.
• OPEN THE STROLLER SLOWLY AND BE CAREFUL WHERE YOU PLACE
YOUR HANDS. KEEPING YOUR HANDS ON THE HANDLE IS THE BEST
WAY TO UNFOLD THE STROLLER.
OPENING THE STROLLER FRAME
A Release the frame lock (1) and open the frame (2).
B Lift the handle as shown by the arrow until you hear a clicking sound which
indicates the frame is fully opened and locked.
CAUTION
‘CLICK’
A
B
Page 14
14
STROLLER ASSEMBLY
A Slide both sides of the axle into the axle attachment housings on the stroller
frame until you hear a ‘click’. Pull on the axle to ensure it is locked into position.
B To remove the axle, press down on the axle release buttons (left and right) (1)
and pull the axle away from the stroller frame (2).
‘CLICK’
‘CLICK’
INSTALLING AND REMOVING THE STROLLER AXLE
1
2
CAUTION
CAUTION
Page 15
STROLLER ASSEMBLY
INSTALLING THE FRONT WHEELS
A Slide each front wheel mounting pin into the housings on the frame until you
hear a ‘click’ which indicates they have locked into place.
B Pull on both front wheels to ensure they are locked into the frame housings.
‘CLICK’
‘CLICK’
REMOVING THE FRONT WHEELS
A Press and hold the release button on the front of the wheel housing (1) and pull
each wheel out of the housing (2).
1
2
15
Page 16
STROLLER ASSEMBLY
INSTALLING THE REAR WHEELS
A Slide the rear wheel axle into the rear wheel housing and push in until you hear
a ‘click’ which indicates the wheel is locked into place.
B Pull on both rear wheels to ensure they are locked into the frame housings.
REMOVING THE REAR WHEELS
A Locate the rear wheel release button found on the brake bar (1). Hold the
button down and pull the rear wheel out of the wheel housing (2).
‘CLICK’
‘CLICK’
2
1
16
Page 17
STROLLER ASSEMBLY
ATTACHING THE STORAGE BASKET
17
1
2
ATTACHING THE STORAGE BASKET
A Position the storage basket into the area under the seat. Slide the hook tabs at
the front of the basket (No. 1) behind the metal bar and attach to the loop tabs
on the basket to secure. Slide the hook tabs on the side of the basket (No’s. 2
& 3) behind the metal bar and attach to the loop tabs on the basket to secure.
Slide the hook tab (No. 4) through the brackets on the inside of the frame and
attach to the loop tabs on the basket to secure.
B Wrap the hook tabs on the rear of the storage basket around the axle and
attach to the loop tab to secure.
4
3
2
1
Page 18
18
STROLLER ASSEMBLY
ATTACHING THE STROLLER SEAT
ALWAYS REMOVE YOUR CHILD FROM THE STROLLER SEAT BEFORE
INSTALLING, REMOVING OR CHANGING THE SEAT DIRECTION.
PLEASE NOTE: The seat is reversible so it can be attached to the frame in
the forward facing position or the rearward facing position when used alone
in the upper position on the stroller frame.
A Press down on the lower section of the brake pedal to engage the brake.
Insert the seat connectors on the seat unit into the housings on the stroller
frame.
B Push down on the seat until a ‘click’ is heard which indicates the seat
connectors have locked into the housings. Pull up on both sides of the seat to
ensure that it is locked into place correctly.
IMPORTANT NOTE:
‘CLICK’
CAUTION
A
B
Page 19
19
STROLLER ASSEMBLY
REMOVING THE STROLLER SEAT
ALWAYS REMOVE YOUR CHILD FROM THE STROLLER SEAT BEFORE
INSTALLING, REMOVING OR CHANGING THE SEAT DIRECTION.
A Lift both release levers on the seat connectors at the same time to release the
seat from the housings on the stroller frame.
B Lift the seat up and away from the stroller frame.
IMPORTANT NOTE:
CAUTION
B
A
Page 20
STROLLER ASSEMBLYSTROLLER ASSEMBLY
ATTACHING THE CANOPY
20
The sun is very strong. DO NOT LEAVE YOUR CHILD EXPOSED TO THE
SUN. The canopy or hood on this product will not give your child total
protection from the harmful rays of the sun.
A Slide the canopy runners on each side of the canopy into the canopy
attachments located on either side of the seat frame.
B Attach the canopy to the seat with the zipper to secure the canopy to the seat
frame.
C To adjust the canopy, open the canopy by pulling forward or close by pushing
the canopy backward.
IMPORTANT NOTE:
CAUTION
‘CLICK’
C
B
A
Page 21
STROLLER ASSEMBLY
ATTACHING THE CANOPY
21
ATTACHING THE CANOPY
D To expose the mesh section of the canopy, fully unzip the centre section of the
canopy and fold the fabric panel in the centre section over the front section of
the canopy.
E For extra protection from the sun, pull the sun visor out from under the front of
the canopy.
F To cover the mesh section of the canopy, pull the fabric panel back over the
mesh.
F
D
D
E
Page 22
22
STROLLER ASSEMBLY
REMOVING THE CANOPY
A Fully unzip the canopy from the seat.
B Slide the canopy runners out of the canopy attachments located on either side
of the seat frame.
A
B
ATTACHING THE ARM BAR
WHEN A CHILD IS IN THE STROLLER, KEEP THE ARM BAR ATTACHED TO
THE STROLLER SEAT At ALL TIMES.
A Align the pins on each side of the arm
bar with the sockets on the seat and
slide the arm bar pins into the sockets
until a ‘click’ is heard which indicates
the pins have locked in.
B Pull up on the arm bar to ensure
that it is locked into place correctly.
IMPORTANT NOTE:
CAUTION
Page 23
23
STROLLER ASSEMBLY
IMPORTANT NOTE:
THE ARM BAR CAN BE OPENED FROM EITHER SIDE OF THE SEAT WITH
OUT REMOVING IT FROM THE STROLLER SEAT.
A Press the release buttons in on the
side of the arm bar socket on both
sides of the stroller seat and pull the
arm bar out of the sockets to remove.
REMOVING THE ARM BAR
B To assist with putting a child in the
stroller you can release the arm bar
on one side. Press the release button
in on the side the arm bar socket and
pull the arm bar forward. Rotate the
arm bar clear of the stroller. Reattach
the arm bar after fastening the child in
the harness.
Page 24
STROLLER ASSEMBLY
ATTACHING THE SHOULDER HARNESS PADS
IMPORTANT NOTE:
ENSURE THAT THE SHOULDER STRAPS ARE FITTED THROUGH THE
APPROPRIATE HARNESS SLOTS TO SUIT YOUR CHILD’S SEATED
SHOULDER HEIGHT.
A Release the harness buckles (Refer
to Page 32) and slide the shoulder
harness pads onto the shoulder
harness straps.
ATTACHING THE BOOT COVER
A Place the bottom of the boot cover
over the leg rest.
B Pull the top section of the boot cover
under the arm bar and the fold it over
the top of the arm bar.
C Connect the hidden magnets to
secure the boot cover in place.
24
Page 25
25
IMPORTANT NOTE:
ENSURE THE RAIN COVER IS KEPT AWAY FROM THE CHILD’S FACE.
REFIT THE RAIN COVER IF REQUIRED TO ENSURE YOUR CHILD IS SAFE.
ATTACHING THE RAIN COVER
A Place the rain cover over the canopy.
Pull the front elastic section of the
rain cover over the stroller leg rest.
Ensure the rain cover fits snugly over
the canopy and is securely fitted to
the stroller seat.
B Attach the rain cover together at the
back of the leg support using the
press studs on the tabs.
STROLLER ASSEMBLY
USING THE BRAKES
PLEASE NOTE: Pressing down on the brake pedal locks both rear wheels.
A Press down on the lower section of
the brake pedal to engage the
parking brake.
WARNINGS: ALWAYS APPLY THE BRAKES WHEN
THE STROLLER IS STATIONERY.
A
Page 26
26
STROLLER OPERATION
B When the stroller is being used in
single stroller mode, press down on
the upper section of the brake pedal
to disengage the parking brake.
USING THE BRAKES
C When the stroller is being used in
tandem mode (e.g. using the second
seat or bassinet in the lower position
on the stroller), lift the lower section
of the brake pedal with your foot to
disengage the parking brake.
Page 27
27
STROLLER OPERATION
ADJUSTING THE HANDLE HEIGHT
2
1
2
1
‘CLICK’
PLEASE NOTE: There are 11 handle
height settings.
A Release the handle by unlocking the
handle height adjustment locks on
both sides of the handle. Adjust the
handle to the required height and
lock the handle height adjustment
locks on both sides of the handle.
PLEASE NOTE: Always lock the swivel wheels when using the stroller on
rough surfaces as it will minimise wheel wobble.
You may need to swivel the wheels to the proper position to engage the
swivel lock.
A Locate the swivel lock slider on the
front of the wheel. Push the swivel
lock slider down to allow the wheels
to swivel.
B Push the swivel lock slider up to lock
the wheels.
USING THE FRONT WHEEL SWIVEL LOCK
360º
‘CLICK’
Page 28
28
STROLLER OPERATION
ADJUSTING THE LEG REST
B Depress the release buttons on both
sides of the leg rest hinge (1) and
hold while lowering the leg rest (2) to
the desired position.
1
1
2
3
2
1
ADJUSTING THE LEG REST
• THE LEG REST FEATURE IS PROVIDED FOR YOUR CHILD'S COMFORT.
• THE LEG REST IS NOT DESIGNED TO SUPPORT EXTRA WEIGHT.
• DO NOT ALLOW CHILDREN TO STAND OR SIT ON THE LEG REST. IT WILL
DISENGAGE IF EXTRA WEIGHT IS APPLIED.
• IF LEG REST DISENGAGES SIMPLY LIFT UP AGAIN TO RESET LEG REST
MODE.
PLEASE NOTE: There are 3 leg rest
positions.
A Pull the leg support up to raise to the
desired height.
IMPORTANT NOTE:
Page 29
29
STROLLER OPERATION
ADJUSTING THE BACKREST
3
4
3
2
1
WARNINGS:
• THE UPRIGHT POSITIONS ARE NOT SUITABLE FOR USE WITH CHILDREN
LESS THAN 6 MONTHS OLD.
• THE LOWEST RECLINE POSITION SHOULD BE USED TO TRANSPORT
BABIES. THE BACKREST CAN BE ADJUSTED TO A MORE UPRIGHT
POSITION AS THE CHILD GROWS OLDER AND IS ABLE TO SUPPORT
ITS HEAD WITHOUT ASSISTANCE.
PLEASE NOTE: There are 4 backrest recline positions.
A Lift the recline lever located at the back of the seat and hold while raising or
lowering the backrest to the desired position. The seat will lock into position
when the recline lever is released
PLEASE NOTE: If the child is sitting in the seat, support the backrest as it
reclines. If you have difficulty adjusting the backrest you may need to
remove the child from the seat to allow you to raise or lower the backrest
with ease.
Page 30
30
STROLLER OPERATION
SECURING YOUR CHILD IN THE HARNESS
• A five point harness is provided to restrain your child.
• Buckle tongues separate for added safety.
• To reconnect buckle tongues and to secure the child in the harness please
follow the steps below carefully.
PLEASE NOTE: Each waist buckle tongue has a raised rib on one side and
can only be locked into the buckle assembly with the raised rib facing up.
Ensure the harness straps are not twisted as they may become
uncomfortable for the child.
A Always apply the brakes.
Place child in stroller seat.
Position the shoulder strap near the
child’s shoulder.
Position crotch strap between legs.
Thread the waist strap buckle
tongues through the shoulder straps
tongue guides.
• ENSURE YOUR CHILD IS SECURED WITH A CORRECTLY ADJUSTED
HARNESS.
• THE ADJUSTED HARNESS SHOULD CLOSELY FIT THE CHILD.
• NEVER LEAVE THE HARNESS BUCKLED WHEN NOT FITTED TO A CHILD
IN THE STROLLER, BECAUSE THE HARNESS CAN FORM LOOPS WHICH
MAY POSE A STRANGULATION HAZARD.
• WHEN HARNESS IS NOT IN USE, DISCONNECT SHOULDER STRAPS
FROM THE WAIST STRAPS AND BUCKLE TO PREVENT
STRANGULATION.
WARNING: USE THE HARNESS AT ALL TIMES.
Rib
Page 31
31
ADJUSTING THE HARNESS
A Tighten or loosen the shoulder straps and crotch strap by sliding the 3 bar
harness adjuster up or down. The crotch strap should be adjusted to a snug fit.
B Tighten or loosen the waist straps, hold and lift the 4 bar harness adjuster and
pull the harness strap to adjust to the desired fit. The waist strap needs to fit
firmly around the child.
CAUTION: DO NOT SLIDE 3 BAR SLIDER OVER THE
SEWN TAB ON SHOULDER HARNESS.
STROLLER OPERATION
SECURING YOUR CHILD IN THE HARNESS
B Hold the centre button in on the crotch buckle and insert the waist buckle
tongues into the crotch strap buckle until you hear a ‘click’.
C Repeat the procedure on the other side.
IMPORTANT: Pull on each waist buckle tongue to make sure they are
locked into the crotch buckle assembly. If not, repeat above procedure.
Page 32
32
STROLLER OPERATION
OPENING THE HARNESS
A Release the harness by pressing the centre button in on the crotch buckle
while pulling the waist tongues out of the crotch buckle.
IMPORTANT NOTE:
THE HARNESS CAN BE ADJUSTED TO THREE DIFFERENT HEIGHTS TO
ACCOMMODATE THE CHILD. THE SHOULDER STRAPS MUST BE
POSITIONED NEAR THE CHILD’S SHOULDERS.
ADJUSTING THE SHOULDER HARNESS HEIGHT
A To change the shoulder harness height, push the shoulder harness tongue out
of the current harness slot and through the back of the seat. Select the
appropriate shoulder harness height and pull each shoulder harness tongue
through the harness slot.
Page 33
33
STROLLER OPERATION
USING THE TETHER STRAP
WARNINGS: USE THE TETHER STRAP TO STOP
THE STROLLER ROLLING AWAY.
• THE STROLLER IS DESIGNED FOR USE ON FLAT OR GENTLY SLOPING
SURFACES, AND MAY BE UNSTABLE ON HIGHER SLOPING AND
UNEVEN SURFACES AND USERS SHOULD BE AWARE OF THE
POSSIBILITY OF THE STROLLER ROLLING AWAY OR TIPPING OVER.
• NEVER LET GO OF THE STROLLER WHEN PARKED ON AN INCLINE OR
SLOPING SURFACE BECAUSE IT MAY SLIDE OR TIP OVER. ALWAYS
PARK ON A FLAT SURFACE AND APPLY THE BRAKES.
• ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS
STATIONARY.
A A wrist tether strap is provided on the handle grip. Slide your hand through the
tether strap loop whenever you use the stroller. Only remove your hand from
the tether strap loop when the brakes have been applied to the stroller wheels.
Page 34
STROLLER OPERATION
USING THE STROLLER
PLEASE REFER TO PAGE 7 FOR LIFTING TECHNIQUES.
• Always ensure you bend your knees where appropriate and take due care when
lifting the frame.
• With your hand through the wrist tether strap loop, push the stroller holding the
handle.
• The stroller can be steered in the desired direction - allowing the front wheels to
swivel will make this easier.
• The front wheels may wobble or oscillate when walking fast. Locking the front
swivel wheels will stop this.
• The stroller can be taken up kerbs by either pressing down on the handles and
raising the front wheels or turning the stroller around and pulling the stroller up
the kerb.
• Caution is required when pushing the stroller on a steep slope as the stroller
may become unstable. Always hold the handles firmly.
• Do not run with the stroller.
• Whenever you stop, always apply the brakes before you leave the stroller.
• Do not hang bags or goods from the handle. Use the storage basket.
34
Page 35
35
STROLLER OPERATION
FOLDING THE STROLLER
• REMOVE THE CHILD FROM THE STROLLER BEFORE COMMENCING
ANY FOLDING OPERATION.
• FOLD THE STROLLER SLOWLY AND BE CAREFUL WHERE YOU PLACE
YOUR HANDS.
• WHEN FOLDING THE STROLLER, BE AWARE OF THE DANGER OF BEING
INJURED BY MOVING PARTS AND LOCKING DEVICES DURING THE
PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS.
• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE
INJURED WHEN THE STROLLER IS BEING FOLDED, DUE CARE SHOULD
BE EXERCISED.
• KEEP CHILDREN CLEAR OF THE STROLLER DURING FOLDING THE
STROLLER.
PLEASE NOTE: It is recommended to remove the stroller seat from the
frame before folding for easier handling & a more compact fold.
PLEASE REFER TO PAGE 7 FOR LIFTING TECHNIQUES.
A Remove the child from the stroller.
B Close the canopy. (Refer to Page 20)
C Lock the brakes. (Refer to Page 25)
D Lock the swivel wheels. (Refer to Page 27)
E Adjust the leg rest to the lowest position. (Refer to Page 28)
F Raise the backrest to the fully upright position. (Refer to Page 29)
Page 36
36
STROLLER OPERATION
G To fold the frame when in tandem mode, ensure the handle is extended so that
the black triangle markers are clearly visible.
H Lift the frame folding handle and push down on the secondary lock button until
it is in the position shown.
I Lift the frame using using the frame folding handle (1); the frame will fold (2),
allowing you to engage the frame lock.
CAUTION
CAUTION
H
I
H
1
2
FOLDING THE STROLLER
Page 37
37
STROLLER OPERATION
IMPORTANT NOTES:
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
• TO AVOID INJURY: BEND YOUR KNEES WHEN OPENING, LIFTING,
CARRYING, FOLDING, UNFOLDING OR ADJUSTING THE STROLLER OR
ANY ACCESSORIES.
A Ensure the chassis lock is engaged on the frame before lifting the stroller.
To lift the stroller, grasp the frame halfway along the stroller, so the stroller is
balanced.
LIFTING AND CARRYING THE STROLLER
Page 38
Series No. TP3401
Flexx
™
Tandem Pack
Includes: Second Seat, Tandem Axle,
Height Adaptors & Rain Cover
Page 39
WARNINGS
ALWAYS FOLLOW THE MANUFACTURERS INSTRUCTIONS.
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE OF
THIS STROLLER.
THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL.
WARNINGS:
• SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR
USE WITH THIS STROLLER BY BRITAX.
• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH
THIS STROLLER.
• THE MAXIMUM WEIGHT OF THE CHILD USING THIS SECOND SEAT IS
NOT TO EXCEED 17KG.
IMPORTANT NOTES
• DO NOT USE THIS SECOND SEAT WITH ANY OTHER MODELS OF
STROLLER.
• THE SECOND SEAT MUST BE CORRECTLY INSTALLED AND LOCKED
ONTO THE TANDEM AXLE.
• THE SECOND SEAT CAN ONLY BE USED IN THE FORWARD FACING
POSITION, CONNECTED TO THE REAR OF THE STROLLER.
• DO NOT OVERLOAD THE STROLLER. OVERLOADING WILL CAUSE THE
STROLLER TO TIP BACKWARDS.
• THE SECOND SEAT MUST BE REMOVED FROM THE FRAME BEFORE
FOLDING.
39
Page 40
PARTS LIST
1 x Second seat axle
1 x Second seat
1 x Canopy
1 x Set of height adaptors
1 x Arm bar
1 x Set of shoulder harness pads
40
Page 41
41
TANDEM PACK ASSEMBLY
INSTALLING AND REMOVING THE TANDEM AXLE
A Slide both sides of the axle into the
axle attachment housings on the
stroller frame until you hear a ‘click’.
Pull on the axle to ensure it is
locked into position
B To remove the axle, press down on the axle release buttons (1) located on the
left and right hand side and pull the axle away (2) from the stroller frame.
CAUTION
1
‘CLICK’
‘CLICK’
CAUTION
2
Page 42
TANDEM PACK ASSEMBLY
42
ATTACHING THE STORAGE BASKET
A When the tandem axle is installed on the stroller, the storage basket must be
increased in size to fit into the basket area under the seat. To enlarge the
storage basket, open all the press studs located around the middle section of
the basket. Position the storage basket into the area under the seat. Slide the
hook tabs at the front of the basket (No. 1) behind the metal bar and attach to
the loop tabs on the basket to secure. Slide the hook tabs on the side of the
basket (No’s. 2 & 3) behind the metal bar and attach to the loop tabs on the
basket to secure. Slide the hook tab (No. 4) through the brackets on the inside
of the frame and attach to the loop tabs on the basket to secure.
B Wrap the hook tabs on the rear of the
storage basket around the axle and
attach to the loop tab to secure.
1
2
4
3
2
1
Page 43
TANDEM PACK ASSEMBLY
ATTACHING THE SECOND SEAT TO THE TANDEM AXLE
A Lower the second seat and insert the
connectors into the housings on the
axle and push down on the seat until
a ‘click’ is heard which indicates the
connectors have locked into the
housings.
CAUTION
‘CLICK’
43
IMPORTANT NOTES:
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
• WHEN ATTACHING OR REMOVING THE SECOND SEAT, BE AWARE
OF THE DANGER OF BEING INJURED BY MOVING PARTS AND LOCKING
DEVICES DURING THE PROCESS. KEEP ALL HANDS AND LIMBS CLEAR
OF THESE PARTS.
• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE
INJURED WHEN THE STROLLER IS BEING FOLDED OR UNFOLDED, DUE
CARE SHOULD BE EXERCISED.
• KEEP CHILDREN CLEAR OF THE STROLLER DURING FOLDING OF THE
STROLLER.
• THE SECOND SEAT CAN ONLY BE USED IN THE FORWARD-FACING
POSITION.
ATTACHING THE CANOPY - See Page 20
REMOVING THE CANOPY - See Page 22
ATTACHING THE ARM BAR - See Page 22
REMOVING THE ARM BAR - See Page 23
ATTACHING THE SHOULDER HARNESS PADS - See Page 24
Page 44
TANDEM PACK ASSEMBLY
ADJUSTING THE BACKREST - See Page 29
SECURING YOUR CHILD IN THE HARNESS - See Pages 30 & 31
ADJUSTING THE HARNESS - See Page 31
OPENING THE HARNESS - See Page 32
ADJUSTING THE SHOULDER HARNESS HEIGHT - See Page 32
44
REMOVING THE SECOND SEAT FROM THE TANDEM AXLE
A Lift both release levers on the seat connectors at the same time to release the
seat from the housings on the axle. Lift the seat up and away from the axle.
IMPORTANT NOTES:
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
• ALWAYS REMOVE YOUR CHILD FROM THE SECOND SEAT BEFORE
FOLDING OR REMOVING THE SECOND SEAT.
CAUTION
CAUTION
Page 45
TANDEM PACK ASSEMBLY
B To remove the adaptors, press in and hold the button on the inside of the
adaptor and then pull each adaptor up and out of the frame sockets.
+10cm
A
B
45
IMPORTANT NOTE:
THE HEIGHT ADAPTORS ARE SUPPLIED WITH THE SECOND SEAT.
THE HEIGHT ADAPTORS ARE USED TO CREATE MORE SPACE BETWEEN
THE UPPER & LOWER POSITIONS (IF REQUIRED) OF THE STROLLER.
A Attach the height adapters to the stroller frame by lining up the connectors with
the frame sockets. Press down on the adaptors until you hear a ‘click’ which
indicates the adaptors have locked into the frame. Pull up on the height
adaptors to ensure they are locked into the frame sockets.
WARNING: DO NOT USE THE HEIGHT ADAPTORS
(SUPPLIED WITH THE SECOND SEAT) IN SINGLE STROLLER MODE.
INSTALLING AND REMOVING THE HEIGHT ADAPTORS
Page 46
Series No. C3401
Flexx
™
Bassinet
PLEASE NOTE: THE FLEXX BASSINET MEETS THE REQUIREMENT OF THE
AS/NZS 8811.1:2013 - SLEEP SURFACES - TEST FOR FIRMNESS, AND
EN 1466:2014/AC:2015 SAFETY REQUIREMENTS FOR CARRY COTS.
Page 47
WARNINGS
ALWAYS FOLLOW THE MANUFACTURERS INSTRUCTIONS.
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE OF
THIS BASSINET.
THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS ESSENTIAL.
WARNINGS:
• DO NOT USE THE BASSINET ONCE THE CHILD CAN SIT UP.
• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR
USE WITH THIS STROLLER BY BRITAX.
• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH
THIS STROLLER.
• THE MAXIMUM WEIGHT OF THE CHILD USING THIS BASSINET IS NOT TO
EXCEED 9KG FOR THE BASSINET.
IMPORTANT NOTES
• THE FLEXX BASSINET IS THE ONLY BASSINET DESIGNED TO FIT THE
FLEXX STROLLER.
• REMOVE THE STROLLER SEAT OR INFANT CARRIER FROM THE
STROLLER FRAME BEFORE FITTING THE BASSINET.
• ALWAYS REMOVE YOUR CHILD FROM THE BASSINET BEFORE
INSTALLING ON OR REMOVING FROM THE STROLLER FRAME.
• THE BASSINET MUST ALWAYS BE IN THE REARWARD-FACING
POSITION (FACING TOWARDS THE HANDLE) WHEN IN THE UPPER
POSITION ON THE STROLLER FRAME. THE BASSINET MUST ALWAYS BE
IN THE FORWARD-FACING POSITION (FACING TOWARDS THE FRONT
OF THE STROLLER) WHEN IN THE LOWER POSITION.
• THE BASSINET MUST BE REMOVED FROM THE FRAME BEFORE
FOLDING.
• DO NOT LIFT THE STROLLER BY THE BASSINET.
47
Page 48
PARTS LIST
1 x Bassinet frame
1 x Bassinet mattress
1 x Bassinet boot cover
1
2
‘CLICK’
‘CLICK’
A B
ASSEMBLING THE BASSINET
BASSINET ASSEMBLY
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
A Raise the bassinet canopy until it clicks into place.
B Press down on the base of the bassinet & pull up on the bassinet canopy
handle to raise the sides of the bassinet.
48
Page 49
ASSEMBLING THE BASSINET
BASSINET ASSEMBLY
C Pull the frame supports outward by the straps until they lock under all 4 clips.
Push down lightly on the top edges of the carry cot to ensure that the frame
support rods are firmly locked in place.
D Place the mattress into the bassinet.
4x
‘CLICK’
C D
ATTACHING THE BASSINET TO THE STROLLER FRAME
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
IMPORTANT NOTE:
ALWAYS REMOVE YOUR BABY FROM THE BASSINET BEFORE
ATTACHING OR REMOVING THE BASSINET.
PLEASE NOTE: The bassinet can only be used in rearward facing mode
in the upper position on the stroller frame. The stroller frame will not fold
with the bassinet attached. It must be removed before folding.
49
Page 50
BASSINET OPERATION
ATTACHING THE BASSINET TO THE STROLLER FRAME
A Press down on the lower section of the brake pedal to engage the brake.
Insert the connectors on the bassinet into the housings on the stroller frame.
B Push down on the bassinet until a ‘click’ is heard which indicates the
connectors have locked into the housings. Gently pull up on the canopy handle
to ensure the bassinet has locked into the housings on the stroller frame.
‘CLICK’
50
Page 51
BASSINET OPERATION
ATTACHING THE BOOT COVER
A Lift the bassinet release lever located at the bottom of the canopy and using
the handle, lift the bassinet away from the stroller.
REMOVING THE BASSINET FROM THE STROLLER FRAME
A Place the boot cover over the top
edge of the bassinet and attach using
the press studs and hook and loop on
both sides of the bassinet.
1
2
51
Page 52
BASSINET OPERATION
ADJUSTING THE CANOPY
PLEASE NOTE: There are 3 canopy positions.
A The bassinet canopy can be lowered by pressing in the two buttons on the
inside of the canopy hinge and rotate the canopy down to the desired position.
B Raise the bassinet canopy until it clicks into place.
ONLY USE THE CARRY HANDLE WHEN THE CANOPY IS IN THE FULLY
EXTENDED AND LOCKED POSITION TO TRANSPORT THE BASSINET.
CAUTION:
52
Page 53
ATTACHING THE BASSINET TO THE TANDEM AXLE
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
PLEASE NOTE: THE BASSINET CAN ONLY BE USED IN THE FORWARDFACING MODE (FACING TOWARDS THE FRONT OF THE STROLLER) WHEN
IN THE LOWER POSITION.
A Lower the bassinet and insert the
connectors into the housings on the
second seat axle and push down on
the bassinet until a ‘click’ is heard
which indicates the connectors have
locked into the housings. Gently pull
up on the bassinet canopy handle to
ensure it is locked into place.
CAUTION
BASSINET OPERATION
‘CLICK’
REMOVING THE BASSINET FROM THE TANDEM AXLE
A Lift the bassinet release lever located
at the bottom of the canopy and using
the handle, lift the bassinet up and
away from the axle.
IMPORTANT NOTES:
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
• ALWAYS REMOVE YOUR CHILD FROM THE BASSINET BEFORE
REMOVING THE BASSINET FROM THE TANDEM AXLE.
CAUTION
53
Page 54
Unity
Click & Go Baby Capsule
Please Note: Flexx Unity Baby Capsule Receivers are sold separately and must
be attached to the stroller before attempting to install the Britax Safe N Sound
Unity Baby Capsule or the Britax Safe N Sound Unity Baby Capsule Isofix Compatible.
Page 55
WARNINGS
• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH
THIS STROLLER.
• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR
USE WITH THIS STROLLER BY BRITAX.
• THE MAXIMUM WEIGHT OF THE CHILD USING THE BRITAX SAFE N
SOUND UNITY NEOS BABY CAPSULE OR BRITAX SAFE N SOUND UNITY
BABY CAPSULE ISOFIX COMPATIBLE IS NOT TO EXCEED 12kg.
• THE BRITAX SAFE N SOUND UNITY NEOS BABY CAPSULE OR BRITAX
SAFE N SOUND UNITY BABY CAPSULE ISOFIX COMPATIBLE ARE THE
ONLY COMPATIBLE BABY CAPSULES DESIGNED TO FIT THE FLEXX
STROLLER.
• REMOVE THE STROLLER SEAT OR BASSINET FROM THE STROLLER
FRAME BEFORE INSTALLING THE BABY CAPSULE.
• THE BABY CAPSULE MUST BE CORRECTLY INSTALLED AND LOCKED
ONTO THE STROLLER.
• THE BABY CAPSULE CAN ONLY BE ATTACHED IN THE UPPER POSITION
ON THE STROLLER FRAME AND MUST ALWAYS BE IN THE REARWARD FACING POSITION (FACING TOWARDS THE HANDLE).
• SECURE THE CHILD USING THE BABY CAPSULE HARNESS AT ALL
TIMES.
• DO NOT LEAVE CHILD IN THE BABY CAPSULE FOR EXTENDED PERIODS.
• THE BABY CAPSULE IS DESIGNED TO PROVIDE MOBILITY OUTSIDE OF
THE CAR BUT IT SHOULD NOT BE USED INSTEAD OF AN APPROPRIATE
COT.
• THE BABY CAPSULE MUST BE REMOVED FROM THE FRAME BEFORE
FOLDING.
WARNINGS:
IMPORTANT NOTES:
55
Page 56
IMPORTANT NOTES
IMPORTANT NOTES:
• THE SUN IS VERY STRONG. DO NOT LEAVE YOUR CHILD EXPOSED TO
THE SUN. THE CANOPY OR HOOD ON THIS PRODUCT WILL NOT GIVE
YOUR CHILD TOTAL PROTECTION FROM THE HARMFUL RAYS OF THE
SUN.
PLEASE NOTE: THESE INSTRUCTIONS ARE FOR INSTALLING AND
REMOVING THE BABY CAPSULE ON THE STROLLER ONLY. FOR
INSTALLING AND PROPER USE OF THE BABY CAPSULE IN THE CAR,
PLEASE FOLLOW THE INSTRUCTION BOOK PROVIDED WITH THE BABY
CAPSULE.
56
Page 57
CAUTION
BABY CAPSULE
A Insert the baby capsule receivers into
the stroller frame sockets ensuring
the white triangles on the receivers
and the stroller frame sockets are
aligned. Press firmly down on the
baby capsule receivers until you hear
a ‘click’ which indicates the receivers
have locked into the stroller frame
sockets. Pull up on the baby capsule
receivers to ensure they are locked
into the frame sockets.
B To remove the baby capsule
receivers, press in and hold the
button on the inside of the receiver up
and out of the frame sockets.
CAUTION
WARNING: THE FLEXX UNITY BABY CAPSULE
RECEIVERS (PURCHASED SEPARATELY) MUST BE ATTACHED TO
THE STROLLER FRAME BEFORE ATTEMPTING TO INSTALL THE
BRITAX SAFE N SOUND UNITY CLICK & GO BABY CAPSULE OR THE
BRITAX SAFE N SOUND UNITY BABY CAPSULE ISOFIX COMPATIBLE.
INSTALLING AND REMOVING THE BABY CAPSULE RECEIVERS
‘CLICK’
‘CLICK’
57
Page 58
BABY CAPSULE
PLEASE NOTE: Ensure the baby is secured in the baby capsule with the
harness at all times. Refer to the baby capsule instructions regarding
placing and securing your baby in the baby capsule.
The baby capsule has been fitted with a hood when using the stroller. The
hood may also be used in the car.
ATTACHING THE UNITY CLICK & GO BABY CAPSULE TO THE
STROLLER FRAME
CAUTION
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
IMPORTANT NOTE:
ALWAYS REMOVE YOUR BABY FROM THE BABY CAPSULE BEFORE
ATTACHING OR REMOVING THE BABY CAPSULE.
PLEASE NOTE: The baby capsule can only be used in rearward facing mode
in the upper position on the stroller frame. The stroller frame will not fold
with the baby capsule attached. It must be removed before folding.
A Lock the stroller brake. (Refer to
Page 25).
Insert the connectors on the
baby capsule into the receivers on
the stroller frame.
58
Page 59
BABY CAPSULE
ATTACHING THE UNITY CLICK & GO BABY CAPSULE TO THE
STROLLER FRAME
B Push down on the baby capsule until
a ‘click’ is heard which indicates the
connectors on the baby capsule have
locked into the baby capsule
receivers. Pull up on the baby capsule
to ensure that it is securely locked
onto the stroller frame.
REMOVING THE UNITY CLICK & GO BABY CAPSULE FROM
THE STROLLER FRAME
PLEASE REFER TO PAGE 7 FOR SMART LIFTING TECHNIQUES.
A Lock the stroller brake. (Refer to
Page 25)
Squeeze both release levers on the
Click & Go connectors at the same
time and support the weight of the
baby capsule. Lift and remove the
baby capsule from the stroller frame.
‘CLICK’
59
Page 60
CARE AND MAINTENANCE
• To prolong the life of your stroller, bassinet or second seat - keep each product
clean and do not leave it in the direct sunlight or in the car boot for extended
periods of time.
• Removable fabric covers and trims may be cleaned using warm water with a
household soap or mild detergent. Allow it to dry fully, preferably away from the
direct sunlight.
• Non removable fabric covers and trims may be spot cleaned using a damp
sponge with soap or a mild detergent. Allow it to dry completely before folding
or storing it away.
• In some climates the covers and trims may be affected by mould and mildew.
To help prevent this occurring, do not fold or store the product if it is damp or
wet. Always store the product in a well ventilated area.
• When using your stroller at the beach - completely clean your stroller
afterwards to remove the sand and salt from the mechanisms and wheel
assembly. Sand and salt will cause premature wear and corrosion.
• If there are compression marks on the tyres - Use a domestic hair dryer to
gently warm (DO NOT OVERHEAT) the tyre and the compression marks
should slowly disappear.
• Always check parts regularly for tightness of screws, nuts, and other fasteners tighten if required. To maintain the safety of your nursery product, seek prompt
repairs for bent, torn, worn or broken parts.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
60
Page 61
NOTES
61
Page 62
NOTES
62
Page 63
NOTES
63
Page 64
Art No. 4002098_C
BRITAX CHILDCARE PTY. LTD.
A Britax International Company
ABN 55 006 773 6000
99 Derby Road Sunshine
Victoria 3020 Australia
Britax Childcare Pty Ltd
(Customer Service 1300 303 330)
Britax Childcare (NZ) Ltd
(Customer Service 0508 688 822)
Due to the variations in style and design of our products, the
illustrations used in this instruction booklet are generic.
We reserve the right to alter these products without notice.
The Britax Trademark is the property of Britax Childcare
Holdings Limited - UK.
This product is designed to comply with Australian and
New Zealand standard AS/NZS2088:2013 “Prams and
Strollers - Safety Requirements.”
2017 Copyright Britax Childcare Pty. Ltd. Australia
youtube.com/britaxaustralia
facebook.com/britaxaustralia
twitter.com/britaxaustralia
pinterest/britaxaustralia
britax.com.au
1300 303 330
Loading...