Brinkmann INS-800-2200-B User Manual

OWNER’S MANUAL & OPERATING INSTRUCTIONS

MANUEL ET INSTRUCTIONS D'UTILISATION

WARNING

READ AND FOLLOW ALL WARNINGS

AND INSTRUCTIONS IN THIS

MANUAL TO AVOID PERSONAL

INJURY OR PROPERTY DAMAGE.

AVERTISSEMENT

LIRE ATTENTIVEMENT ET RESPECTER

TOUS LES AVERTISSEMENTS ET LES

INSTRUCTIONS DE CE MANUEL POUR

ÉVITER TOUTE BLESSURE CORPORELLE

ET ENDOMMAGEMENT DES BIENS.

INS-800-2200-B_DualXenon-bi.qxd 7/18/03 4:12 PM Page 1

Parts List

1 Dual Xenon spotlight 2 120-volt AC charger 3 12-volt DC charger/adapter lighter plug

Owner’s Manual

OPERATING INSTRUCTIONS

READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS IN THE OWNER’S MANUAL

BEFORE OPERATING SPOTLIGHT.

Inspect contents of the box to ensure all parts are included and undamaged.

Step 1: Depress trigger switch in handle to turn spotlight ON. Step 2: Release trigger switch to turn spotlight OFF.

To Operate

• Never place spotlight face down when light is on or is still hot from recent use. Doing so could burn/ignite surfaces such as seats, carpeting, etc. and cause major property damage.Always turn spotlight off when not in use.

• To prevent serious damage to eyesight,never look into spotlight when light is on. Do not shine light into the face of someone else.

• Do not touch lens of spotlight when light is on or if it was recently on.The lens will be hot and could cause serious burns.

• Do not place spotlight in water.Keep all components dry and out of water at all times.

• Do not allow children to handle or operate this spotlight.

• Do not use this product for other than its intended use.

• Do not operate in close proximity of combustible or flammable materials.

• Do not attempt to operate spotlight if cord, plug, bulb or any part of the spotlight is damaged or corroded.

• Only use AC charger and DC lighter plug that are provided with the Dual Xenon spotlight or their replacements.

• A damaged battery can leak acid. Avoid contact with eyes and skin. If contact occurs, flush immediately with large amounts of water.DONOT ingest.If contact with eyes or ingestion occurs, consult physician immediately.

IMPORTANT SAFETY WARNINGS

READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS IN THE OWNER’S MANUAL

BEFORE OPERATING SPOTLIGHT.

WARNING

USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR SPOTLIGHT.

FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL

COULD RESULT IN BODILY INJURY OR PROPERTY DAMAGE.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INS-800-2200-B_DualXenon-bi.qxd 7/18/03 4:12 PM Page 2

Step 1: Make sure trigger switch is not locked in the ON position. Step 2: Plug the AC charger or DC charger/adapter into the socket located on

the base of the spotlight handle as illustrated.

Step 3: For DC Charger/Adapter:

Plug the other end of the DC charger/adapter into a cigarette lighter receptacle.

For AC Charger:

Plug the other end of the AC charger into a wall outlet.

Step 4: Allow the spotlight to charge for at least 8 hours. Do not allow to

charge more than 12 hours.

Note: LED indicator on base of handle turns off automatically when battery

is fully charged.

Step 5: Remove spotlight from the charger before operating.

See chart for recommended charge times.

Continuous Beam Using Lock Button:

Step 1: For a continuous beam,depress trigger switch and slide the lock button

to the LOCKED position.

Step 2: To unlock and turn spotlight OFF, slide the lock button to the

UNLOCKED position.

NOTE: To lock the Dual Xenon in the OFF position, release trigger switch, then

slide the lock button to the LOCKED position.

WARNING: Always turn spotlight off when not in use.

Switching Between Single and Dual Beams:

Step 1: For single beam,slide switch on back of light to one dot, as illustrated. Step 2: For dual beam,slide switch on back of light to two dots, as illustrated.

NOTE: The Dual Xenon will burn for a pproxima tely 40 minutes if using both

beams, or approximately 85 minutes if using only one beam.

To Operate

Trigger Switch

LED Indicator

Lock Button

Beam Switch

Single Beam

Dual Beam

Unlocked

Locked

To Charge

4812

Battery Charge

USAGE (Minutes)

CHARGE TIME (Hours)

Charge Times

Charge time is dependent on usage of the

product. See chart below for recommended charge time.

IMPORTANT: The EPA Certified RBRC

Battery Recycling Seal on the nickel cadmium (NiCd) battery contained in our product indicates The Brinkmann Corporation is

voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC

program provides a convenient alternative to placing used NiCd batteries into the trash or the municipal waste stream, which may be illegal in your area. Please call 1-800-8-BATTERY™ for information on NiCd battery recycling and disposal bans/restrictions in your area. The Brinkmann Corporation’s involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.

INS-800-2200-B_DualXenon-bi.qxd 7/18/03 4:12 PM Page 3

Glass Retainer

Rubber Cap

To Replace Bulb

Only use Brinkmann xenon bulb that is designed for the Dual Xenon spotlight as a replacement. Use of any other bulb may result in poor performance and may damage your spotlight.

NOTE: Handling the bulb can leave oil from your fingers on the bulb. To

extend the life of the new bulb and maximize brightness, gently clean off bulb with soft cloth or tissue.Make sure the reflector does not touch or bend the bulb while replacing spotlight head.

Step 1: Disconnect spotlight from charger. Step 2: Remove front rubber cap from barrel of spotlight. Step 3: Pinch the wings of the glass retainer together and lift as illustrated. Step 4: Pull glass and reflector away from rear housing. Step 5: Pull old bulb straight out of bulb holder. Step 6: Make certain that "legs" on new bulb are straight. Insert "legs" into

the two holes in the bulb holder.

Step 7: Gently push bulb straight in until fully seated and centered. Step 8: To reassemble,place the glass and reflector on the rear housing.

Insert the glass retainer into the rear housing.

Step 9: Replace rubber cap. WARNING: Do not touch the lamps when light is on or if it was recently on.

The lamps will be hot and could cause serious burns.

Glass & Reflector

Rear Housing

Tips to Avoid Damage to Your

Dual Xenon Spotlight

• Never attempt to wipe or clean the inner reflective surface of the reflector. Touching or wiping the surface will damage it permanently.

• The lens is made of tempered glass.Avoid dropping or sharp impact on spotlight to prevent damage.

• Do not allow hot lens to come in contact with water or materials subject to heat damage.

• The spotlight is weather resistant.It is not waterproof. Do not use the spotlight under water or store outdoors.

• Use only Brinkmann xenon bulb that is designed for your Dual Xenon spotlight. Use of any other bulb may result in poor performance and may damage your spotlight.

• After months of use,cigarette lighters can build up corrosion that may prevent the DC lighter plug from making good contact. It may be necessary to clean the inside of your cigarette lighter receptacle with a fine emery cloth.Before cleaning receptacle,remove the fuse to prevent it from shorting out.

The retractable hanging ring allows spotlight to hang while in use or during storage.

To Hang/Store Dual Xenon

INS-800-2200-B_DualXenon-bi.qxd 7/18/03 4:12 PM Page 4

+ 2 hidden pages